the last equivalent to the PCI-6024E

Similar Questions

• Simultaneous use of PCI-6024E (former) and BNC 6210 (new) possible?

  Hi all

  I've updated to NOR-DAQ 8.9.5 to get the job of BNC 6210. I also have an old 6024E PCI installed. After the update, MAX shows the PCI-6024E and all tasks configured for this device with a little red cross. The tasks do not work (error-200477 message: no devices configured), and while I can choose the PCI-6024E or-Daq, the button for etc test panel is grayed out in the devices section.

  According to the NOR-DAQ 8.9.5 readme, both the 6210 BNC and the PCI6024E are supported for my XP system.

  Clues as to how I could get both work?

  Thanks for the reply. I solved the problem by uninstalling OR-DAQ 8.9.5 and installation 8.9 (because 8.9.5 wouldn't work with my LabView 7.1). Now, the two devices work fine.

• Digital triggering PCI-6024E problem

  In my view, the PCI-6024E is intended to support that integrates digital triggering. However, I get the following message if poster every time I try a digital triggering:

  "Error-200452 is produced in property Node DAQmx trigger (arg 1) in DAQmx Start Trigger (PowerPlay) .vi:1-> relaxing test.vi.

  Possible reasons:

  Vital statistics: Property specified is not supported by the device or is not applicable to the task.

  Property: Start.TrigType

  "Task name: _unnamedTask<245>"

  I'm on 8.9 DAQmx and Labview 8.6.

  I've included the simple vi, I tried to test a digital triggering with where I made some stupid mistakes.

  Thank you!

  Hey Ptuinluff,

  Have a look here for information and an example on how to use another subsystem to allow the trigger to start.  Let me know if you have any questions.

  John S

  Technical sales engineer

  National Instruments

• Incorrect, test the results of the e/s digital PCI-6024E in MAX

  Hi all

  I have a problem with PCI-6024E. It is for the Commission alone OR installed on a target computer. First he just used OR-traditional DAQ (7.1, if I'm not mistaken) and it worked fine. Some time ago I installed NOR-DAQmx 8.7.1 on the same computer because it is necessary to run both programs written with NOR-DAQmx and NOR-traditional DAQ. As I know there is no harm to do both OR-DAQ and NOR-DAQmx on the same computer if they are not used at the same time. You can see the traditional under NOR-DAQmx devices and peripheral branches DAQ PCI-6024E jury in MAX. When I run the self-test, self-calibration or Reset Device, Max there is no problem. But Test panels (under the direction of NOR-DAQmx) has a rather strange behavior. When I press the "Start" button in tab e/s digital Test panels window with all the digital lines in input, the 4 first green indicators are on and the other 4 are not. And then nothing happens or I press the 'Stop' button or not. I have the same card as a virtual in my MAX on a development computer, and there is a different behavior of it (I don't have traditional DAQ here, just the same version DAQmx). During the entire procedure of test until I press the button 'Stop', the port State 8 lines constantly evolves so the Green indicators are switched on and off with different ways through all possible combinations of logic '1' and '0' in each line of the port.

  The problem is really obvious when trying to control the statements of some laboratory equipment using their passage through PCI-6024E. digital controls. In this case I get auto turn on/off devices connected to the first 4 lines (which are always lit for some reason any as stated that the Green indicators).

  What should I do? This means the Agency is malfunctioning or there is some conflict of data acquisition and acquisition of data-mx? I would try reinstalling DAQ - mx, but I don't think it's a way out of the situation. I work under Windows XP SP2.

  I appreciate all help.

  Igor-

  Your digital outputs will remain in their last State configured unless the device is reset, in which case they will go to the default value (high, in this case).  So if the last State of the low output of your digital program, as long as you do not call the Device.vi DAQmx reset or shut down the computer, they will remain weak.

  If you have other questions about this application in LabVIEW, it would be better to create a new post on the forum so that we can keep these two separate issues (States of I/O digital by default against digital programming in LabVIEW).  If you are looking for a starting point, you can open the Finder example in LabVIEW ('Help' to find examples).  "" Once the example Finder opens, click on input and output material"DAQmx ' digital generation ' write Dig Chan.vi.  This will help you start.

  Better luck with your request and have a great day!

• How the pressure transducer Validyne system-&gt; Validyne CD280-Dual-&gt; SCB - 68-&gt; PCI-6024E-&gt; LABVIEW works and how we can calibrate the pressure sensor?

  Hello

  I am completely new to LABVIEW software.

  I learn a LABVIEW code existing my pressure (attached) acquisition system which has the path of data as follows: pressure transducer Validyne--> Validyne CD280 - Dual--> SCB - 68--> PCI - 6024E--> LABVIEW and I have a few question:

  1. How does the complete system of the transducer to the LABVIEW work? That is, if we apply the pressure of the transducer, it will change the resistance of the probe then...?

  2. How can I find the equation that expresses the relationship between the pressure and the tension to the keys of the Validyne double-CD280 in the LABVIEW?

  3. If I want to do the probe calibration, what are steps?

  Thank you

  You did not include most of the subVIs.

• What version of the PCI Express x 16, it's my motherboard has

  I am running:

  Pavilion - p6320y

  -AMD Phenom II X 4 820

  -8 GB RAM

  -SATA HARD DRIVE 1 TB (7200 RPM)

  -Motherboard model: Violet6-GL8E

  Question: What version of the PCI Express x 16 is the slot on this motherboard: 1.x, 2.0 or 2.1?

  Can't get this information anywhere.

  Hello:

  I don't think that anyone will be able to give you a definitive answer.

  This article gives the date for the PCIe ranges various x versions.

  http://en.Wikipedia.org/wiki/PCI_Express

  Since you have a relatively new PC, I would say that it is certainly not less than PCIe 2.0 and probably PCie 2.1.

  I have a HP 8200 Elite CMT. I think that it is released at the beginning of this year, or very end of last year. 6570 PCIe 2.1, I use an AMD Radeon card in my PC.  It works very well.

  Paul

• How to calibrate the PCI-6110 with NOR-DAQmx

  Hello

  I am a new user of the PCI-6110 Council tries to run the calibration using LabVIEW procedure. I look at the document "Calibration" on the page of the manuals for the Board of Directors,

  http://sine.NI.com/NIPs/nisearchservlet?nistype=psrelcon&NID=11888&lang=us&q=FQL: 28locale % 3Aen % 29 + AND + % 28phwebnt % 3 A 1081 + OR + phwebnt % 3 A 7075% 29 + AND + 28nicontenttype % 3Aproductmanual % 29 + AND + % 28docstatus % 3Acurrent % 29% 20RANK % 20nilangs: en & title = NOR + PCI-6110 + manual

  One of the first steps in the document is to call the AI_Configure command to set the input mode, beach, etc. I'm using LabVIEW 8.5 with the NOR-DAQmx software, and I can not find the command (which, in LabVIEW, seems to be "AI Config.vi") anywhere. The calibration paper was written in 2003, and I gather from Google searches (please, correct me if wrong) that this command is actually a part of NOR-DAQ traditional, who was replaced by driver OR DAQmx.

  My question is this: what is the equivalent to AI_Configure command in the latest software? Is it perhaps a subsequent document describing how to calibrate using NOR-DAQmx?

  Thanks much for any help.

  Tom McLaughlin

  Hi Tom,

  The calibration Procedure series B, E, M, S, which is also linked from this page, describes how to calibrate the PCI-6110 with NOR-DAQmx.

  Brad

• Satellite U840-113: pilot missing for the PCI Communications controller

  "* Toshiba Satellite U840-113 - PSU4SE: * Win7-Prof - 64-bit with MS-DVD original on off RAID, no RAID oder installed software RAID driver, internal SSD now like normal running, new installed SSD SSD completely new, all the drivers installed successfully - with the exception of the following device: in Device Manager, I find under the"other devices"the position?" Controller PCI-Communications (single) ". *

  Who can help me to locate / find the right driver for this "PCI Communications controller"?

  What ist this? Do I need this?
  The system seems to work perfectly; I disable this feature?

  Thanks a lot for the helpful answers!

  Hello

  This article from Toshiba may be useful:
  http://www.MyToshiba.com.au/support/items/FAQ/222

  The PCI of Simple Communications controller is part of Intel AMT Management Engine Interface and is related to the networking on your computer.

  You will need to install the driver Intel (r) AMT Management Engine Interface.

• need an exact model of the PCI communications controller driver

  Mr President.

  my model is G62 B39 SE

  WINDOWS 7

  64-BIT

  HARWARE ID IS

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C & REV_06

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C

  PCI\VEN_8086 & DEV_3B64 & CC_078000

  PCI\VEN_8086 & DEV_3B64 & CC_0780

  Please I need an accurate model of the PCI communications controller driver

  Hello

  It's a system driver wise called "Intel Management Engine Interface (MEI) ' as mentioned in the following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-83746-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5040732 & sw_lang =

  Please download the exe on the link above and install on your machine.

  Kind regards.

• Compaq DV7800: A Bios Configuration is required for the PCIE graphics card

  HII

  I have a small form factor dc 7800 Desktop

  And I also have a Nvidia 8600GT graphics card

  When I mount the graphics card on the computer PCIe slot

  would you like to work in VGA connector and when I use tha Port DVI form map

  Nothing... So I need a Bios Config to work?

  For the factor, I put the motherboard can configure the card

  I have all the equipment, power supply, HARD drive...

  Can you help me?

  Thank you

  This card is perhaps too powerful to 240W power supply that has your PC.

  I would go with a less powerful card like the Radeon HD 6450.

  Also before installing the video card, uninstall you the card integrated Intel graphics and check the driver to uninstall before installing the nvidia card?

  NVIDIA used to list the current of each of their cards, but now when I click on the sheet for the 8600 GT, I get very little info.

  http://www.GeForce.com/hardware/desktop-GPUs/GeForce-8600-GT/specifications

  The PCI x 16 slot in your PC has a certain power of only 25W max draw and I'm sure that the 8600 GT draws more power than that.

• Satellite M30X-165 - need a driver for the PCI Flash memory

  Hey,.

  I need a driver for the PCI Flash memory, I have already searched the web and posted in other Forums, but I can't find anything. I heard he is hidden somewhere in another file... ? !
  I have a toshiba sm30X-165

  I would be very happy if someone can help me!

  Kind regards

  Freddy

  Drivers for Satellite M30X are placed in the archive on the European driver Toshiba page.
  Product type choose Archive.
  Then the Satellite-> Satellite M-> Satellite M30X

  There, you must download and install the Cardbus and Chip Set Utility driver

• Satellite L500 where I can download the PCI drivers audio No. 82801IB/IR/IH

  Help, please. I have not installed the sound drivers / audio of my Toshiba Satellite L500, can someone please tell me where I can download the PCI drivers audio No. 82801IB/IR/IH
  Its a chip intel.
  Thank you.

  Hello

  If you need drivers then I recommend the European driver of Toshiba page.
  If you have a series of Australian for Toshiba laptop, then you should check the driver Toshiba Australia page.

  But if you need more specific information here, then you should put more details on the specifications and BONES as posted by Akuma.

• Solution to adapt a location PCIe to the PCI standard?

  A few months ago, I buy a HP Pavilion slimline s5750z desktop computer.  The motherboard included has 1 PCIe x 16 slot, 3 x 1 PCIe slots and 1 PCIe x 1 socket minicards.  My question is: are there i/o cards or another solution that will adapt one of these PCIe connectors in a standard PCI?  I have an E - MU 1616 m studio which requires an internal PCI card.  The card E-MU is rather big (definitely not a low-profile card), so I'll probably have to move the internal data of the s5750z in a larger box.  My only holdup is finding a way to adapt one of the PCIe slots (or plug) in a standard PCI card.  All advice, solutions or answers telling me that I'm a dreamer, eager to make the impossible would be most appreciated!

  Hello

  You're right, it is used with a low profile according to this link, even card on newegg Web site, was my bad

  http://www.StarTech.com/product/PEX1PCI1-PCI-Express-to-PCI-adapter-card

  Here is the link, call them and ask them this question they have something for the full card size

  They chat

• 2000-2d19wm HP: I need drivers for the PCI device and SM Bus controller

  I have a Hp 2000-2d19wm and I have downgraded to win8 to win7. Now I am trying to install the drivers and I can't find it on the HP website. Please help me.

  Hello:

  You need this driver for smbus controller...

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=cp_118001_1

  You need this driver for the PCI Dev:

  Realtek card reader driver

  File name: sp64801.exe

• Weird waveform using the PCI-5922

  Hello

  I'm having some difficulty with PCI-5922.

  Rather than see a sinusoidal signal (generated by the PCI-5421), I see the forms attached wave, MAX and configured niScope EX Acquisition.vi

  Sometimes he would turn to show a normal sine wave, often times it expires.

  What could be a problem?

  Thank you

  Fomin

  It's weird.

  Could you give more details about your Setup?

  (1) what is your operating system?

  (2) what are the versions of NOR-SCOPE and NOR-FGEN you?

  (3) you have another source of signals to test so that you can narrow down the problem to the digitizer or the generator?

  (4) can we measure the same thing on the channel 0 and channel 1?

  (5) what is expected of your sinusoidal signal amplitude?

  (6) what is the result of executing a self-calibration on two of these cards?

  -Jennifer O.