ASA5500 radius attributes web vpn

Similar Questions

• IOS Easy VPN Server / Radius attributes

  Hello

  I made an easy VPN server installation with a running 12.2 2621XM router (15) output T5. VPN Clients/users are authenticated against Cisco ACS 3.2 by RADIUS.

  It works fine, but there is a problem that I can't solve. Each user must have the same VPN assigned IP address whenever it is authenticated.

  The ACS sends the right radius attribute (box-IP-Address) back to square of IOS, but this address is not assigned to the client. The customer always gets the next available IP address in the local set on the router.

  How can I solve this problem?

  You will find the relevant parts of the configuration and a RADIUS "deb" below.

  Kind regards

  Christian

  AAA - password password:

  AAA authentication calls username username:

  RADIUS AAA authentication login local users group

  RADIUS AAA authorization network default local group

  crypto ISAKMP policy 1

  Group 2

  !

  crypto ISAKMP policy 3

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto identity hostname

  !

  ISAKMP crypto client configuration group kh_vpn

  mypreshared key

  pool mypool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac shades

  !

  mode crypto dynamic-map 1

  shades of transform-set Set

  !

  users list card crypto mode client authentication

  card crypto isakmp authorization list by default mode

  card crypto client mode configuration address respond

  dynamic mode 1-isakmp ipsec crypto map mode

  !

  interface FastEthernet0/1

  IP 192.168.100.41 255.255.255.248

  crypto map mode

  !

  IP local pool mypool 172.16.0.2 172.16.0.10!

  Server RADIUS attribute 8 include-in-access-req

  RADIUS-server host 192.168.100.13 key auth-port 1645 acct-port 1646 XXXXXXXXXXXXXXXX

  RADIUS server authorization allowed missing Type of service

  deb RADIUS #.

  00:03:28: RADIUS: Pick NAS IP for you = tableid 0x83547CDC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:28: RADIUS: ustruct sharecount = 2

  00:03:28: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:28: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  4, len 73

  00:03:28: RADIUS: authenticator 89 EA 97 56 12 B1 C5 C2 - C0 66 59 47 F7 88 96

  68

  00:03:28: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:28: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:28: RADIUS: username [1] 10 "vpnuser1".

  00:03:28: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:28: RADIUS: User-Password [2] 18 *.

  00:03:28: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/4 l

  in 108

  00:03:28: RADIUS: authenticator C1 7 29 56 50 89 35 B7 - 92 7 b 1 has 32 87 15 6

  A4

  00:03:28: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:28: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:28: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:28: RADIUS: Tunnel-Password [69] 21 *.

  00:03:28: RAY: box-IP-Netmask [9] 6 255.255.255.0

  00:03:28: RADIUS: Framed-IP-Address [8] 6 172.16.0.5

  00:03:28: RADIUS: [25] the class 37

  00:03:28: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:28: RADIUS: 2F 33 63 30 61 38 36 34 31 61 76 70 75 73 [3/c0a8641a 6F 2F

  /vpnus]

  00:03:28: RADIUS: 65 72 31 [1]

  00:03:28: RADIUS: saved the authorization for user 83547CDC to 83548430 data

  00:03:29: RADIUS: authentication for data of the author

  00:03:29: RADIUS: Pick NAS IP for you = tableid 0x82A279FC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:29: RADIUS: ustruct sharecount = 3

  00:03:29: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:29: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  5, len 77

  00:03:29: RADIUS: authenticator 13 B2 A6 CE BF B5 DA 7th - 7B F0 F6 0b A2 35 60

  E3

  00:03:29: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:29: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:29: RADIUS: username [1] 8 'kh_vpn '.

  00:03:29: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:29: RADIUS: User-Password [2] 18 *.

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/5 l

  in 94

  00:03:29: RADIUS: authenticator C4 F5 2F C3 EE 56 DA C9 - 05 D6 F5 5 d EF 74 23

  AF

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:29: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:29: RADIUS: Tunnel-Password [69] 21 *.

  00:03:29: RADIUS: [25] class 35

  00:03:29: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:29: RADIUS: 2F 34 63 30 61 38 36 34 31 61 2F 6 b 5F 68 76 70 [4/c0a8641a

  [/ kh_vp]

  00:03:29: RADIUS: 6 [n]

  00:03:29: RADIUS: saved the authorization for user 82A279FC to 82A27D3C data

  Assignment of an IP address via a server Raidus is currently not supported, even if your Radius Server is through an IP address, the router will ignore it and just assign an IP address from the pool locla. In fact, the pool room is the only way to assign IP addresses currently.

  On the only way to do what you want right now is to create different groups VPN, each reference to a local IP pool with an address in it. Then ask each user connect to the appropriate by their VPN client group.

  Yes, messy, but just try to provide a solution for you.

• ACS5.1 - AD and mapping of RADIUS attributes

  Hello

  I am trying to dynamically assign IP addresses for users of VPN of AD (without IAS service). Is it possible?

  I know that there is a restriction that "Dial-in users are not taken in charge by announcement in ACS (note in 'acsuserguide51') but I'm not exacly sure, which may or may not do with it."

  "Authorization profiles" RADIUS attributes tab I try manually add a specific attribute (box-IP-Address).

  I have no problem (everything works fine) with the award of a static in a way as address below:

  

  AD is already integrated with ACS and I managed to download the directory attributes particular msRADIUSFramedIPAddress

  

  When I change the ' attribute value 'static to the dynamic type I see to select AD (but "Select" which should list all of the available attributes is empty).

  

  Is it possible in this way or my concept wrong?

  I know I can do it directly (ASA <->AD attribute mapping), but I want to ACS to make

  best regards and thx for all help

  Przemek

  Your baisc approach is

  fix. However, when you dynamically assign the IP address of type RADIUS attributes in an authorization profile you get only presented for the selection of attributes in the store identities (in this case AD) which are also a type IP address. In your example, it is of the type "integer64.

• WEB - VPN in outsite interface

  Hi all

  I'm putting a WebVPN, but I have a problem when the vpn through outsite interface access.

  If I put inside the interface for web vpn users allowed, access is normally done, but outside the interface is not possible.

  Debug displays the message "can't find political IKE initiator.

  Configuration:

  WebVPN

  port 444

  allow outside

  allow inside

  Auto-signon allow ip 172.17.2.35 255.255.255.255 type auth ntlm

  remote type tunnel-group WEBVPN access

  attributes global-tunnel-group WEBVPN

  authentication-server-group LOCAL AD_LDAP

  I try to access between the link https://ASAIP:444

  OBS: I can get telnet using port 444 on the external interface

  Can someone help me?

  TKS a lot.

  Rafael Mendes

  Why don't you just remove the ACL of the dynamic encryption card? that should be the case and the two connections will work.

  Thank you

• Web VPN/SSL - general Split Tunnel capable?

  When I look through some examples of configuration for IOS Web VPN - it seems you attract to the filling of a web page of web sites that users can go to. I would be rather thin client act as client light 4.x CVPN - divided for example tunnel with access to a resource internal resource. Is this possible with Cisco VPN Web? Also - with is WebVPN any ability of the NAC?

  I'm not sure IOS SSL vpn, but on the asa webvpn, there is a complete client ssl option. With this, you can either create a tunnel, or all split tunnel and the only defined networks. I hope that answers your question.

• ACS 5.2 - Support for RADIUS attributes per user

  Hi all

  Does anyone know if it is possible to configure the RADIUS attributes on a per user in GBA 5.2 basis?

  That was possible under ACS 4.x, however, that I can't seem to find reference if ACS5.2 supports.

  Thank you

  Leon

  You can do this by setting by using attributes and then by substution attribute.

  You can see an example of it to set an internal user attribute to use as the value for the field address-IP-box

  This is just an example and can be applied also to any attribute RADIUS in which set an attribute of the user of the same type. Values can also be taken from an external identity as AD store

• PIX 515e - Web VPN

  Hello

  Just a quick question, am I right to think that a PIX 515e would not support Web VPN?

  Concerning

  J Mac

  You are right!

• Web vpn:

  Hi all

  I'm vpn web configuration on cisco 3845, I have a few questions

  (1) how to change the appearance of the web vpn portal to include include logos of company etc.

  (2) that it supports connections to ip phone/Tablet/iPad etc.? If Yes is that it requires no special configuration?

  (3) If a router can be integrated directly into PPL?  without Ray thanks

  1. check say customization link

  http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6657/prod_white_paper0900aecd80512071.html

  2. no need for special configuration for this.

  3 ldap is System1 15.1 m version

  Note all useful messages *.

  Jawad

• Add under "Setting up groups" RADIUS attributes ACS 4.2

  Hi Security Experts,

  I need to add RADIUS attributes to a custom under the 'Groups Configuration' page provider ACS 4.2. From now on, I see of Cisco Aironet RADIUS attributes.

  IETF RADIUS attributes etc in the page "setting up groups. How can I ensure that the RADIUS attributes for a provider also appear on this page?

  PS: I have the useful messages rate

  Thank you

  Boudou

  Under the "Interface", you can set which you want to view the RADIUS attributes. It is probably just a missing check for your provider.

  The Options for RADIUS are described here:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/A_RADAtr.html

• ACS 5.1 - profile of the authorization, the RADIUS attributes

  Hello

  I am setting up Radius AAA for cat6K switch.

  For the authentication of its work and the user can connect to. But for the assignment of a privilege level, it does not work.
  After loging in, I always get the privilege 1.

  I need your guide on how to Setup GBA 5.1, RADIUS attribute.

  I followed the document to configure the cisco-av-pair to assign 15 privilege and privilege 5, but it does not work.

  This format of the attribute has been shown in document is to define the privilege 15 "shell: priv-lvl = 15.

  Please refer to my screen shot, it's the right way to set it up on ACS 5.1

  Creation date: June 12, 2011 05:56 by: Damiano, Anisha A(ANDAMANI,279917) problem:

  =========

  Authorization does not not as expected

  Resolution:

  ============

  Adding a type of NAS-Prompt service

• False claims RADIUS of customer VPN Cisco ASA 5510

  Hello world

  I use the Cisco VPN client 5.0.7 and Cisco ASA 5510 (7.4 and 8.4.2) VPN RAS solution. Clients are authenticated using certificates and RADIUS AAA (ACS 3.3) and AD.

  Each time, when the client connects, ASA 2 RADIUS requests questions, correct first - which is successfully authenticated by FAC and immediately - second that always fails. I couldn't find information related to this strange behaivor. Function "Double Authentication" (more sympathetic to his name) is only accessible to Anyconnect customers who we do not. When I'm authenicated by using password group, there is only one query RADIUS.

  What is the source of such behavior?

  The negative impact is that my logs are filled with the failed authentication attempts fallacious and users are incrementig attempts failed in the AD meter.

  Debugging of ASA:

  -First application-

  RDS 2011-10-24 16:16:01 0232 14884 request code 172.16.8.1:1645 host = 1 id = 22, length = 145 on port 1025

  RDS 2011-10-24 16:16:01 I 2519 14884 [001] value of username: User1

  RDS 2011-10-24 16:16:01 I 2519 14884 [002] value username-password: 2D A9 B2 D0 15 5F 1E B8 BB DB 3A 38 F5 24 72 B5

  RDS 2011-10-24 16:16:01 I 2538 14884 [005] NAS-Port value:-1072693248

  RDS 2011-10-24 16:16:01 I 2538 14884 [006] Type of Service value: 2

  RDS 2011-10-24 16:16:01 I 2538 14884 [007] value Framed-Protocol: 1

  RDS 2011-10-24 16:16:01 I 2519 14884 [030] value Called-Station-Id: 172.16.8.1

  RDS 2011-10-24 16:16:01 I 2519 14884 [031] value of Calling-Station-Id: 10.4.14.14

  RDS 2011-10-24 16:16:01 I 2538 14884 [061] NAS-Port-Type value: 5

  RDS 2011-10-24 16:16:01 I 2533 14884 [066] Tunnel-Client-Endpoint value: [T1] 10.4.14.14

  RDS 2011-10-24 16:16:01 I 14884 2556 [004] value of NAS-IP-Address: 172.16.8.1

  RDS 2011-10-24 16:16:01 I 2561 14884 [026] Vendor-Specific vsa id: 9

  RDS 2011-10-24 16:16:01 I 2596 14884 [001] cisco-av-pair value: ip:source - ip = 10.4.14.14

  RDS 2011-10-24 16:16:01 I 0282 14884 ExtensionPoint: run the configured scan extension points...

  RDS 2011-10-24 16:16:01 I 0314 14884 ExtensionPoint: advertising [AuthenticationExtension] provider [Cisco EAP generic]

  RDS 2011-10-24 16:16:01 I 0763 14884 ExtensionPoint: Message-[generic EAP] lack of EAP, ignorant...

  RDS 2011-10-24 16:16:01 I 0319 14884 ExtensionPoint: [GenericEAP.dll-> AuthenticationExtension] returned [1 - ignored]

  RDS 2011-10-24 16:16:01 I 0314 14884 ExtensionPoint: asking provider [Download Cisco ACL] [AuthenticationExtension]

  RDS 2011-10-24 16:16:01 I 0763 14884 ExtensionPoint: [DnldACLs] asking not a download of ACL, ignorant...

  RDS 2011-10-24 16:16:01 I 0319 14884 ExtensionPoint: [DnldACLs.dll-> AuthenticationExtension] returned [1 - ignored]

  RDS 2011-10-24 16:16:02 I 14884 0475 AuthorExtensionPoint: run the configured scan extension points...

  RDS 2011-10-24 16:16:02 I 14884 0507 AuthorExtensionPoint: requesting provider [Download Cisco ACL] [AuthorisationExtension]

  RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: looking for ACL from [DnldACLs] to [user1]

  RDS 2011-10-24 16:16:02 I 0512 14884 AuthorExtensionPoint: [DnldACLs.dll-> AuthorisationExtension] returned [1 - ignored]

  RDS 2011-10-24 16:16:02 3360 14884 sent response code 2, id 22 to 172.16.8.1 on port 1025

  RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9

  RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:addr - pool = vpnpool

  RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9

  RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:wins - servers = 10.2.9.12 10.3.9.10 10.4.2.202

  RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9

  RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: IP: DNS-servers = 10.2.9.12 10.3.9.10 10.4.2.202

  RDS 2011-10-24 16:16:02 I 2538 14884 [006] Type of Service value: 2

  RDS 2011-10-24 16:16:02 I 2538 14884 [007] value Framed-Protocol: 1

  RDS 2011-10-24 16:16:02 I 2538 14884 [013] box-Compression value: 1

  RDS 2011-10-24 16:16:02 I 14884 2556 [008] value box-IP-Address: 255.255.255.254

  RDS 2011-10-24 16:16:02 I 2519 14884 [025] value class: CISCOACS:002cb2a9/ac100801/3222274048

  -The second request-

  RDS 2011-10-24 16:16:02 0232 14884 request code 172.16.8.1:1645 host = 1 id = 23, length = 145 on port 1025

  RDS 2011-10-24 16:16:02 I 2519 14884 [001] value of username: User1

  RDS 2011-10-24 16:16:02 I 2519 14884 [002] value username-password: 06 EA 08 AB C7 8F 75 D0 A5 E5 AE B7 A8 1 48 96 b

  RDS 2011-10-24 16:16:02 I 2538 14884 [005] NAS-Port value:-1072693248

  RDS 2011-10-24 16:16:02 I 2538 14884 [006] Type of Service value: 2

  RDS 2011-10-24 16:16:02 I 2538 14884 [007] value Framed-Protocol: 1

  RDS 2011-10-24 16:16:02 I 2519 14884 [030] value Called-Station-Id: 172.16.8.1

  RDS 2011-10-24 16:16:02 I 2519 14884 [031] value of Calling-Station-Id: 10.4.14.14

  RDS 2011-10-24 16:16:02 I 2538 14884 [061] NAS-Port-Type value: 5

  RDS 2011-10-24 16:16:02 I 2533 14884 [066] Tunnel-Client-Endpoint value: [T1] 10.4.14.14

  RDS 2011-10-24 16:16:02 I 14884 2556 [004] value of NAS-IP-Address: 172.16.8.1

  RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9

  RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:source - ip = 10.4.14.14

  RDS 2011-10-24 16:16:02 I 0282 14884 ExtensionPoint: run the configured scan extension points...

  RDS 2011-10-24 16:16:02 I 0314 14884 ExtensionPoint: advertising [AuthenticationExtension] provider [Cisco EAP generic]

  RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: Message-[generic EAP] lack of EAP, ignorant...

  RDS 2011-10-24 16:16:02 I 0319 14884 ExtensionPoint: [GenericEAP.dll-> AuthenticationExtension] returned [1 - ignored]

  RDS 2011-10-24 16:16:02 I 0314 14884 ExtensionPoint: asking provider [Download Cisco ACL] [AuthenticationExtension]

  RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: [DnldACLs] asking not a download of ACL, ignorant...

  RDS 2011-10-24 16:16:02 I 0319 14884 ExtensionPoint: [DnldACLs.dll-> AuthenticationExtension] returned [1 - ignored]

  RDS 2011-10-24 16:16:02 P 2237 14884 user: User1 - Windows user unknown or invalid password

  RDS 2011-10-24 16:16:02 3360 14884 sent response code 3, id 23 to 172.16.8.1 on port 1025

  RDS 2011-10-24 16:16:02 I 2519 14884 [018] value Reply-Message: rejected...

  RDS 2011-10-24 16:16:03 0232 14884 request code 10.2.47.200:1812 host = 1 id = 254, length = 227 on port 32769

  RDS 2011-10-24 16:16:03 2788 14884 (VSA unknown Vendor ID 14179)

  GBA debug:

  -First application-

  AUTH 24/10/2011 16:16:01 I 0365 13060 external DB [NTAuthenDLL.dll]: from [user01] user authentication
  AUTH 24/10/2011 16:16:01 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 user

  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: authentication Windows successfully (by DCCORPMSK04)
  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: information get RAS to the user user1 DCCORPMSK04

  -The second request-
  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: from [user1] user authentication
  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 user
  AUTH 24/10/2011 16:16:02 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication FAILED (Error 1326 L)
  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: retry authentication to the CORP domain
  AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 user
  AUTH 24/10/2011 16:16:02 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication FAILED (Error 1326 L)

  The ASA config:

  Crypto ikev1 allow outside
  Crypto ikev1 allow inside
  IKEv1 crypto ipsec-over-tcp port 10000
  life 86400
  IKEv1 crypto policy 65535
  authentication rsa - sig
  3des encryption
  md5 hash
  Group 2
  life 86400

  !

  internal Cert_auth group strategy
  attributes of Group Policy Cert_auth
  client ssl-VPN-tunnel-Protocol ikev1 l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list aclVPN2
  the address value vpnpool pools
  rule of access-client-none

  !

  attributes global-tunnel-group DefaultRAGroup
  address (inside) vpnpool pool
  address vpnpool pool
  authentication-server-group RADIUS01
  authorization-server-group RADIUS01
  authorization-server-group (inside) RADIUS01
  Group Policy - by default-Cert_auth

  !

  RADIUS protocol AAA-server RADIUS01
  AAA-server host 10.2.9.224 RADIUS01 (inside)
  key *.
  RADIUS-common-pw *.
  AAA-server host 10.4.2.223 RADIUS01 (inside)
  key *.

  Hello

  It is a 'classic' error and has nothing to do with dual authentication, but rather with the fact that you do both radius and authorization of RADIUS authentication.

  If you remove this line:

  authorization-server-group RADIUS01

  you will see that it starts to work properly

  In short: when ASA no authorization of RADIUS, it sends a request to access radius with the username as a password, that's why you see the second application fails all the time.

  This is because the RADIUS authorization is intended to be used when authentication happens using certificates (only) so there is no password.

  Also note that within the RADIUS protocol, authentication and authorization are not separate things, both occur in a single step. So if the ASA makes the radius authentication, he already gets the user attributes in the authentication step and it makes no sense to also make a separate authorization stage (except in a few very rare scenario where you have 2 radius servers, one for authentication and another for permission).

  HTH

  Herbert

• Can ACS adds more Juniper RADIUS attributes?

  Hello

  These attributes RADIUS Juniper taken in charge by Cisco default ACS4.0

  Juniper-Local-user name

  Juniper-allow-orders

  Juniper-deny-orders

  Is it possible to add more 2 attributes

  Juniper-help-Configuration

  Juniper-deny-Configuration

  Kind regards

  Audrey

  Hi Audrey,.

  4.0 the only way to add these attributes is to contact TAC and get the script directly from the developers.

  This problem has been resolved in ACS 4.1.23

  http://www.Cisco.com/cgi-bin/support/Bugtool/onebug.pl?BugID=CSCsi18979&submit=search

  If that answers your question, then please mark this thread as solved, so that others can benefit from.

  Kind regards

  Jagdeep

• MS RADIUS and Cisco VPN client

  We currently have with a Server Windows RAS and IAS authentication with PPTP to users.

  I want to move a hub (we have two not used) and the use of the Cisco VPN client with IPSEC 3005, also using the RADIUS (IAS) in Windows to authenticate against Active Directory.

  I have a config to work for the client and it performs authentication, but I'm afraid that you can't configure IAS to work with IPSEC, unless you configure the policy for

  "Unencrypted authentication (PAP, SPAP).

  on the Authentication tab

  and

  "No encryption".

  on the encryption tab.

  Are encrypted with IPSEC credentials to establish the tunnel of the Cisco VPN client?

  For RADIUS PAP authentication, the user name is clear and the password is encrypted with the RADIUS shared secret.

  To maximize security, you would use GANYMEDE + or IPSec transport mode and isolated VLAN. But for most of us, strong passwords and physical security prevents the RADIUS PAP to a significant weakness.

• How to account for the Radius Server cisco vpn client

  Hello

  I would like to realize vpn cisco customers

  My config is:

  AAA authentication login default local radius group
  RADIUS AAA authentication login aaa_radius local group
  RADIUS group AAA authorization exec default authenticated if
  AAA authorization vpn LAN
  failure to exec AAA accounting
  action-type market / stop
  RADIUS group
  !
  AAA accounting network aaa_radius
  action-type market / stop
  RADIUS group

  RADIUS-server host x.x.x.x auth-port 1812 acct-port 1813 key xxxxx

  No package of accounitng is sent to the server radius, only the packages autthetication

  RADIUS server is freeradius

  Thank you

  Pet

  Hello!

  The sequence of commands you add to your configuration:

  1. in the case of former card crypto

  crypto-NAME of the customer accounting card card list aaa_radius

  2. in the case of isakmp profiles

  Profile of crypto isakmp PROFILE NAME

  accounting aaa_radius

  When the NAME of the map and the PROFILE NAME real names for you profile crypto map or isakmp respectively.

  I hope this helps.

  Best regards.

• change the customer RADIUS attributes sent by switch

  I recently started to use NPS to authenticate logins to my Cisco devices and I have the basics of work.  However, I have a need to add an additional constraint corresponding to my NPS network policies.

  Now I use the friendly name of the RADIUS client and/or IP address but I can't find the template for the syntax of these constraints NPS can do what I need without I create literally dozens of policies.  I need somehow add an attribute to a certain group of switches so that I can "filter" which group AD Windows can connect to them by using a strategy that corresponds to that custom attribute.

  In the constraint list NPS, I see I have a few options like 'Called Station ID', 'NAS ID' and 'Customer Vendor ID', etc. available.  Is there a way to change these attributes of the switch and send them to the NPS then I could achieve what I want.  For example, I could set up the 'Client Vendor ID' of my special switches with custom data that I could then use to match the political refusal NPS.

  Any ideas?

  TIA

  Hello Diego again :)

  I checked with a friend who used the NPS more than me and he was not aware of a way to create groups of location"in NPS or something similar where you can distinguish two different NADs.

  However, it provided an interesting solution. He suggested that we use a regular expression in the field identifier Sin in NPS. The regular expression would be for the IP subnet for that particular site. For example, assume that you have two sites:

  1 A: site with local subnet of 192.168.30.x 24

  2. site B: with local subnet of 10.10.1.x 24

  In NPS, you can build a rules like this:

   If NAS Identifier is 10\.10\.1\.* and AD Group is Site_B_Admins Then Full access

  And for the Site A

   If NAS Identifier is 192\.168\.30\.* and AD Group is Site_A_Admins Then Full access

  Of course, to do this, each site must have a single subnet that does not overlap with other sites.

  Hope that gives you some kind of a solution