Associate and extrude path

Similar Questions

• How drive letters are assigned to external drives and file path names?

  How drive letters are assigned to external drives and file path names? MyBook is a drive letter (M) when it is connected to my desktop computer and another letter (L) when it is connected to my husbands office, USB key has the same letter, no matter what usb port is used. Is the letter assigned when the file is created and does not change? or is it to the port to which it is connected to? in what computer?

  Each computer assigns the player to the first drive letter not used in alphabetical order.  It makes no difference what port it connects to.

  Boulder computer Maven
  Most Microsoft Valuable Professional

• What is the difference between Unicast RPF and Reverse Path Forwarding?

  I am confused between Unicast RPF and Reverse Path Forwarding function.

  What is the difference between Unicast RPF and Reverse Path Forwarding?

  Because they have all two please check the address of the source of each package before sending it to the destination too?

  Reverse Path Forwarding is used only when the network want to build a tree shared multicast communication and then we must use Unicast RPF after creation of the shared tree?

  The mechanism of the RPF is mainly used to ensure no loop of routing traffic.

  As you probably already read, it does by ensuring that his route to the source address of a packet received is accessible via the same interface that the packet is entered in the. Think of the notion of "root port" in STP. all root ports are similar to the root, sunflower follow the Sun. Therefore, it is naturally a loop prevention mechanism.

  With multicast traffic, it is quite likely to create multiple loops of routing the nature of 'destination' traffic. For this reason, using a mechanism as the RPF to ensure you are on the "road to the root" (to say) to the source originating multicast traffic. Otherwise if you're not then you either receive this traffic route in a loop, or a suboptimal path.

  uRPF works essentially the same way, except that it is done for unicast traffic instead. Now with unicast traffic your flow is from a source and directs to a single destination. Given that, as the fact that you are using a dynamic routing algorithm (which allows to select the path to a destination), you can have loops of your network for unicast traffic flow routing; of course there may be exceptions to pitfalls of configuration route redistribution.

  However RPF when it is applied to traffic unicast can add another advantage, and it's verification IP source. That's why we can use it as a security mechanism to ensure that data are from where it is supposed to come.

  On the limit of the L2, you then have mechanisms such as guard source IP to ensure that the correct host is not usurpation of their IP address.

  By analogy RPF can be used for checking at source for multicast traffic, and it is intrinsically that however, the most important role is so that it can be used to guarantee without loop routing of multicast traffic.

  I hope that helped clear things upwards and not confused you any more with all this.

• Get the list of virtual machines, storage of data and VMDK / path by cluster

  Hi people,

  as I m new to such things, I m wondering if someone already has a few scripts work to gather a list of all virtual machines, its corresponding data store (s) and the path to the files VMDK (or at least the name of it) - I know that this part has already been resolved - found a couple of them ;-)

  But my problem is, I need this script drilled down by Cluster Edition or Datacenter Edition. As I said I m completely new for this CLI stuff and Don t have any idea how to solve this problem...

  See you soon

  Markus

  Luke, you are right. I should have tested.

  There is a downside to the ForEach command that I almost never use. Normally I use the Foreach-Object cmdlet and that works very well with pipeing the output to Export-CSV.

  Markus, you must use option 2 in this case.

• Problem copy and paste paths in the new document

  Before when I copied and pasted the traces on a new document, it was working fine and the paths are out of the right size. Now even if I don't do anything else when I copy and paste a path into a new document, the trail comes out really small! I tried the two dragging the path and copy and paste, but neither will not work! Any suggestions? Thank you

  Nice day!

  Make the two files have the same resolution (Image > Image size)?

  Kind regards

  Pfaffenbichler

• How to transform a layer object and a path at the same time?

  Hi all

  I know that I will start when you tell me the answer to this!

  I would really like to know if there is a way I can manage to transform a layer object and a path at the same time... or if there is no work around to get there.

  In a Word, for example I spend a VERY long time to create a drive complex around a very detailed object and then at the end note to what twisted and perspective, and would like to straighten.

  Of course I could turn and correct the object and then carefully turn the path - but it will not correct and I have to spend a lot of time the path of adjustment and make SURE, it is perfect.

  Are there not somehow, I was able to transform set?

  Usually, of course, I do all the correction to straighten and correct the perspective in advance, but in some cases after I am done creating the path I then notice that image could have used other adjustments.

  I appreciate all the advice you can get :)

  Thank you kindly,

  Christine

  Transform the layer and then target the way and make "Edit > Transform path > Again. If you make several changes on the layer, and then each time that validate you and leave transformation mode, remember to do the ' transform path > Again "to keep the layer and the synchronized pathname.

• Wait events "direct path write" and "direct path read".

  Hello
  
  We have a query that takes more than 2 minutes. It's a 9.2.0.7 database. We took the request trace/tkprof and identified there so manay 'direct entry path' and 'direct path read' wait for events in the trace file.
  
  WAITING #3: nam = "Write" direct path ela = 5 201 p1 = p2 = p3 70710 = 15
  WAITING #3: nam = "direct path read" ela = 170 201 p1 = p2 = 71719 p3 = 15
  
  In the light of the foregoing, "p1 = 201" is a the file_id, but we could not find any data file, the temporary file, the control file with this id # 201.
  Can you please let us know what "p1 = 201" here, how to identify the file that is causing the problem.
  
  Thank you
  Sravan

  Whatever it is:

  show parameter db_files
  

  back? I think, is that it returns 200.

  Read the file live and direct file writing events are reads and writes of tablespace TEMP. Wait events, folder # is reported as db_files + id of a temporary file. So, 201 means temp #1 file.

  Now, as to your real performance issue.

  Without seeing the SQL and the corresponding implementation plan, it is impossible to be sure. However, the most frequent causes of temporary entries are the operations of sorting and group by operations.

  If you decide to display your plan and SQL execution, please be sure to make it readable by formatting it. Information on how to do this can be found here.

  Hope that helps,

  -Mark

  Published by: mbobak on May 1st, 2011 01:50

• I can't find the "plugin.expose_full_path" preference in the ' subject: config "list and full path is activated!

  I've tried to get rid of some plugins/extensions owrrisome and wanted to show their full path in ' on: plugins ", so went to set the preference of"plugin.expose_full_path"the ' topic: config" list to 'true '. But, I couldn't find there, and the full path seems already displayed in "subject: plugins. What worries me, is that you are supposed to disable the full path when you are finished, because it creates a security risk. So why don't I see the option "plugin.expose_full_path" and why the full path is activated?

  Copied from:
  http://KB.mozillazine.org/about:plugins

  Location of the plugin file:

  • Mozilla 20 and below: To display the full path to the plugin instead of just the file name (for example, in Firefox 20), type Subject: config in the address bar and press the Enter key. Find the plugin.expose_full_path preference and change the value true (by double-clicking on the name of the preference will switch the setting). Warning: Expose the location plugin can have repercussions on safety on some systems. It is best to reset the preference to "false" by default, when you are finished. 1
  • Mozilla 21: There is no way to display the full path of the file in the topic: plugins list. Another way to find the location of the plugin file (for example, in Firefox 21) must inspect the contents of the "pluginreg.dat" file, located in the profile to your Mozilla application folder.
  • Mozilla 22 and above: From version 22 (for example, Firefox 22) an extra row "path:" is included in the on: plugins list, which displays the full path of the file for all plugins. (bug 661961).

• WSN Routing Tables and better path decisions

  Hello

  My team has placed a total of 10 knots in an industrial environment of factory.  Nine are defined as routers, and there is only one end node.  The gateway is a little in the center of this area, and there is no node failed.  The coverage area is four floors with approximately 63000 square feet of floor area per level.  I'm having a problem with a section of the path used to reach the end node: a quality signal between the 3rd and 4th routers gateway has been ignored in favor of a lower quality signal.  If I take this 4th router and move it very closely the 3rd router and do a reset it will pick up the 3rd router signal and remain at about 60% intensity of the signal for several minutes.  However, this 4th router will soon fall sharply to about 20% intensity (much less that NEITHER recommended by 30%) of the signal.  The network is to decide than 3 jumps of signal is relatively good is worse than a jump involving a bad signal?  Also, is there a way to read what are routing tables to determine if it is indeed the case?

  Thank you!

  Garrett

  We suggest you use the least necessary routers for your background. Routers add the chance for the performance of the network has declined due to uninteded jump. Then, even when food is available, the default choice for the nodes must be nodes except routers are needed.

• TS2012 - SequentialModel customization to include the version of sequence and the path in the report header

  I was able to add a PreUUT reminder to a single sequence to allow me to understand the SequenceFile.Version and the SequenceFile.Path to the header of my report.

  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  

  The station ID:	TESTENG6-DMA
  Serial number:	NONE
  Date:	Friday, October 17, 2014
  Time:	09:35:09
  Operator:	pbrooks
  Run time:	14.0482135 seconds
  Number of results:	25
  The result of the object to measure:	Past
  Reference number:	423 00079
  Name of the manufacturer:	*******
  Reference of the manufacturer location:	*******
  Test mode:	Production
  Version of the sequence:	0.0.0.130
  Path of the sequence:	C:\Sonus\UX\UX Common.seq

  The recall, I get the sequence using RunState.SequenceFile.AsPropertyObjectFile file reference.

  I don't want to add this reminder to each test sequence, so I want to change the sequence of SequentialModel PreUUT to add the SequenceFile.Version and the SequenceFile.Path to the report header instead.

  Should what technique I use to get a reference to the file of the sequence on the process model PreUUT running?

  Phillip,

  You can use RunState.ProcessModelClient to access the file from the client's sequence in the process template.

  I hope that helps!

• Workspace TestStand, project and relative path

  Hi all

  My colleagues and I use a lot of small projects in TestStand with the architecture of the following folder:

  ...\Package\

  Reports\

  TestStandReport1.html

  TestStandReport2.html

  SubSequence\

  SubSeq1.seq

  SubSeq2.seq

  Main.SEQ

  Configuratio_Files\

  ConfFile1.ini

  ConfFile2.ini

  We move these package a lot on different bench which are not connected to the network and also move us them a lot on a bench (archive, record, work...).

  Several package can have different review in a sequence, so from the point of view of TestStand those are different sequences with the same name. So the problem is when several package exist on the same computer, TestStand could take a sequence from another package without generating an error, but think of the user the sequence used is good.

  So my question is: are there at - it a way, using the workspace and or project in our packages, teststand to say to use the sequence of the packaging and not the other, WITHOUT having to constantly update the search directories?

  Something like setting the path of the sequences relatively to the path of the workspace file.

  Thank you!

  I don't understand why you want to use the workspace or project.  Those not deployed nor are they called what it is.  Therefore, I don't think using the workspace is the right way.

  If I were in your shoes I would like this:

  ...\Package\

  Main.SEQ

  Reports\

  TestStandReport1.html

  TestStandReport2.html

  SubSequence\

  SubSeq1.seq

  SubSeq2.seq

  Configuratio_Files\

  ConfFile1.ini

  ConfFile2.ini

  With your mainsequence at the top level of your package, you can now use the current sequence files directory with Subdirs verified.  In this way, that they will not use modules or dependencies of in this package.

  Hope this helps,

• Signal dynamically defined and clickable path feature

  Hi all

  IM developing a LabVIEW built cutomer application.

  What I want to accomplish is a GUI showing a signal path (photo by treatment and son of connection blocks) that can be changed dynamically also clickable someone.

  In my mind I imagining me a solution involving a container ActiveX holding an HTML object. The HTML object is a local .html file with forms of svg forming threads and treatment blocks. Unfortunately the Microsoft Web browser ActiveX container implemented in LabVIEW support svg and that's why I'm looking for another solution...

  Most likely, the best option for you is by using the image control screws you can use to draw arbitrary shapes (boxes, lines, etc.) by program and you can use mouse events down to see where the user has clicked on the image and to implement things like drag-n - drop.

  Realize that the image control is essentially sets an image as a series of commands (opcodes and data) and is not super effective, then you should probably make sure not ever edit the same photo, but rather use a base image and then add to that.

  Another alternative implementation for something like this is something like the picturebox .NET, but it's perhaps more complicated.

• What is the difference between refnum and the path?

  Hello!

  There is an output of the read/write to the file refnum.

  There is also a data type for the path.

  can someone elaborate a little bit?

  And as explained in the help, you can plug a refnum to the path entry. Please note the behavior of different when you wire up a path or a reference.

• Environmental parameters for Start Up and recovery path

  Is this the path variable normal environment for start-up and recovery in Control Panel?

  "% SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem; C:\Program Files\Fichiers SharedCOM Shared\DLLShared\; C:\Program Files\Fichiers SharedCOM Shared\DLLShared\; C:\Program Files\Fichiers SharedCOM Shared\9.0\DLLShared\"

  Also in the services, I started and running a secondary connection with an unattached profile and another service called 'readyboost' with another unattached profile that is disabled, but these two have passwords on them.

  I reinstalled vista windows from a recovery disk that I ordered from HP.  I have a Pavillion DV6500 and the new facility took 6 hours to complete.  Also my service packs keep uninstall and I have more than 40 x active controls in my addons on new IE8 running without permission.   Is this normal?

  First, it is not normal that Roxio entries be in the path of the environment (although I don't know what Roxio did when installing - it can for some reason any add them, but I can't imagine why).  Did you install Roxio or came with the HP recovery disk?  I would like to remove the entries from Roxio, but it is your decision to do that I don't know what effect this will have on your system.  Roxio doesn't play well with Vista in general (or you can leave them alone because they are probably not wrong).

  Secondly, it is not normal to have 40 controls ActiveX in IE8 modules quickly and without add them yourself.  I don't know how they got there or what they're doing.  I all would disable them until you get this thing figured out.  It is possible that they have been added by HP because you used their recovery process - but I don't know.  Ask HP.

  Thirdly, it seems that the recovery of the system did not work properly.  To install service packs, you must first do a complete update of Windows (perhaps several times), before appear no more.  And then install SP1 (unless it was one of the updates).  Then run Windows update again until no furter updates appear and then install SP2.  Then run Windows Update again until no other updates appear and you will be updated.  If you have tried to install service packs without installing updates firstly this is perhaps why they do not work properly (it isn't normal for service packs to uninstalll on their own).  You need to contact HP again and explain the situation - they can send you bad discs or you will have to start the process.  They may help you with the process and problems of this result.  We can't really help you because it it to HP to start the process and non-Microsoft.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• The soft and critical path calculation

  Hello world

  I'm trying to find some documentation on the critical path and how soft is calculated in Instantis but unfortunately can not find. I hope that it calculates the standard way (criticism = 0 or minus 0 soft; soft = difference between the dates earlier to one less than the later dates of a task task) but seeks to find confirmation for that.

  Any help is appreciated. Thank you

  Eva

  Eva,

  Instantis made a pass forward and backward on the planning activities, looking for the critical path.  These activities have 0 slack or float as well as any changes that they will change the project completion date.