ASUS A8AE - THE is compatible pci-e 2.1?

Similar Questions

• What graphics card do you have used with the motherboard Asus A8AE THE?

  I have an old a1210n with a motherboard A8AE THE with a PCIe x 16 slot 1.0.   I would like to know what graphics cards does anyone have successfully run on this motherboard (see list of models of computer below)?  Unfortunately, which should theoretically work often does not work.   I tried a HD 4850, which produced only blurred video, despite reading a slower hd 4830 and 4650 had worked.

  This forum and other research made me some operation card names (which are too slow or too expensive, (I'm looking for a pass of about 1000 Mark): 7800 oc x1600xt, 8600gs, hd 6850, gtx 470)  I was surprised/skeptic on the last 2.

  The HD 5770, 5750, 5450, 5870 failed.

  At least some of the older hp computers that have the a8ae:

  Pavilion a1100e Desktop, Pavilion a1130e Desktop, Pavilion a1200e Desktop Pavilion a1206n Desktop, Pavilion a1210n Desktop, Pavilion a1211n Desktop, Pavilion a1222n Desktop, Pavilion a1226n Desktop, Pavilion a1228x Desktop a1229x Desktop Pavilion, Pavilion a1230n Desktop Pavilion a1243w Desktop a1253w Desktop Pavilion, Pavilion a1310n Desktop, Pavilion a1314n Desktop, Pavilion a1330e Desktop, Pavilion a1330n Desktop, Pavilion a1350n Desktop, Pavilion a1355c Desktop, desktop Pavilion a1357c Pavilion a1383w Desktop, Pavilion Desktop a1428x, Presario SR1020Z Desktop, SR1030Z Desktop Presario, Presario SR1601NX Desktop, Presario SR1602HM Desktop, Presario SR1603WM Desktop, Presario SR1611NX Desktop, Presario SR1614X Desktop, Presario SR1616NX Desktop, Presario SR1617CL Desktop, Presario SR1630NX Desktop, Presario SR1650NX Desktop, Presario SR1675CL Desktop, Presario SR1700Z Desktop, Presario SR1703WM Desktop, Presario SR1707WM Desktop, Presario SR1710NX Desktop, Presario SR1711NX Desktop, Presario SR1717CL Desktop, Presario SR1720NX Desktop Presario SR1730Z Desktop, Desktop Presario SR1738NX, Presario SR1750NX Desktop, Desktop Presario SR1802FR, Presario SR1802HM Desktop, Desktop Presario SR1807CL, Presario SR1811NX Desktop, Desktop Presario SR1817CL, Presario SR1834NX, Presario SR1850NX Desktop Desktop, Desktop Presario SR1830NX

  Thank you!

  I got the HD 4850 replacement and it works great so far!    Unfortunately, I can't tell what brand, because it was a Chinese generic card.

• How will I know if my Asus laptop is wifi compatible? The model number is PRO61G.

  WiFi compatibility

  How will I know if my Asus laptop is wifi compatible?  The model number is PRO61G.

  Contact ASUS supports.

• How to change the configuration of the BIOS with NO SIGNAL - to accept the new card PCI - ex

  Compaq Presario SR2030NX

  Product #RJ036AA

  S/N {removed privacy}

  MB: ASUS A8M2N - LA

  Bought: October 2006

  OS: Windows XP Media Center 05

  New graphics card: MSI N210-D512D2 graphics card GeForce 210-512 MB, DDR2, PCI-Express 2.0 (x 16), 1 x DVI, 1 x VGA, DirectX 10.1, mono-emplacement

  New: 480w PSU

  ERROR:  NO SIGNAL on monitor and can not reset the BIOS to accept the new video card in the PCI slot

  PROBLEM: The user reports the monitor suddenly became white with blue lines finally erased.   On start-up, the screen shows "No Signal" then turns off.

  Troubleshooting has included:

  Fixing monitor with its cable to another PC - monitor work

  Fixing working monitor and cable to the PC - No Signal

  There is no boot beeps, fans, lamps, not work cable defeated, no video.   I concluded the embedded video component failed.

  Installed the new video PCI - ex card and new power supply 480w and still get NO SIGNAL.   New video card specifications called for a minimum 350w power supply.  The fan on the new video card PCI - ex works.  Search on the HP Support pages indicates that the BIOS should be modified to change the type of PCI slot type in-flight video.  Makes perfect sense to me, sounds like it might work.

  How to reset the BIOS when you do not see what you are doing?

  I have moved the jumpers to reset the CMOS, but cannot tell if it worked or not.  I tried a couple blind BIOS resets, but I could do this for months.

  If I could determine the Version of the BIOS, I might be able to blindly to reset the BIOS.  The Compaq Options of Menu and "BIOS Setup Utility information" web page provides instructions for BIOS version 6 or less and version 7 and greater - menus and access steps are very different.

  QUESTIONS:   How to determine the version of the BIOS.  Which key I hit to access the BIOS (F1, F10, esc, Del)?  Which menu I followed to reset the type of video, so how can I save and exit?

  

  Thanks for any help

  GJB

  Thank you Paul,.

  I didn't know that it was just a function of Regedit - piece of cake.

• Is the iPad compatible with iOS 10 3rd generation?

  Is the iPad compatible with iOS 10 3rd generation? I want to upgrade, mainly using the new maps application. I saw some sites state that it is possible to upgrade a 3rd gen iPad. If not, is there a way to download just the Maps app.

  Thank you

  Lou

  Yes, the 3 gen iPad is compatible with iOS 10. You can update.

• is the new compatible update 37.0.1 with the norton toolbar? If not when?

  is the new compatible update 37.0.1 with the norton toolbar? If not when?

  According to Norton, he works with 37, https://community.norton.com/en/blogs/product-update-announcements/firefox-37-support-norton-toolbar

• Is the ipad-compatible trackpad 2 12,9 pro

  Is the ipad-compatible trackpad 2 12,9 pro

  N ° iDevices use not external pointing devices except the finger or the iPencil in the case of an iPad Pro.

• Upgrading the BIOS. Mobo ASUS P5LP - THE. BIOS of PHX. Tech. of ver.3.16. Pavilion a1620n. Win 7OS.

  I have a Hp Pavilion a1620n with a motherboard ASUS P5LP - THE using Phoenix Technologies Bios VER.3.16 and running Windows 7. I want to upgrade the processor and said that I have to upgrade the Bios before upgrading the processor. I have been researching but can't find any info on how to do it for this particular machine. There is no on-board Bios Flash program and I can't seem to find any information. Any ideas?

  AZ_scuba_dude, welcome to the forum.

  There is no update software/BIOS for Win7 for the computer.  It is unlikely that there will be a developed.  However, there is a BIOS update for XP.  You will need to do a system restore to the original configuration that includes XP.  Once this operation is complete, you can update the BIOS to version: 3.19.  You can do the update using the executable file (sp35100.exe). Although she did not mention anything about what makes the upgrade of the processor.  Here are the Specifications of the motherboard of the computer.  In the processor upgrade information section, it lists the updates that supports HP.

  Please let us know if this solved your problem or not.

• Is the 6s compatible IQ?

  Is the 6s compatible IQ?

  Not without some kind of third party in charge of case or dongle.

• How to get a regular clock (100 MHz, 10 MHz to 20 MHz) of the NI 4462 PCI?

  Is it possible to extract a regular clock, high frequency of the 4462 OR?

  I need to synchronize with another card (a PulseBlaster), which requires a 100 MHz clock: every card can be the main source, but they must stay perfectly synchronized.

  (Both cards have on-board crystal oscillator modules of 100 MHz; one of the PulseBlaster is nested, would be so easy to connect a source external intead)

  I use the PCI version, so the star PXI 10 MHz clock is not available. The 10 MHz or 20 MHz clocks that DAQmx usually exports seem not to be available for routing on this device.

  I can't use the Sampleclock, because it is variable (~ 25.6 MHz, changing with sample-freq) and because it is not active when the 4462 is actually measurements.

  In addition, this clock must be either 100 MHz, or a whole simple fraction of it (e.g. 10 MHz, so that a PLL can re - generate the 100 MHz).

  At the present time, the best option seems to be to solder on the 4462 output pin quartz oscillator - but it's a really ugly way do... has anyone had an experience to make relevant changes?

  Is there a better place to connect to? I would prefer to use the RTSI bus connector, but despite tempting advice in the documentation, it seems not possible to get out of the 10/20 MHz master time base: there is

  an axis called RTSI7/RTSI_OSC, but it is a permanent decline.

  Thanks for your help.

  Nick Dear,

  Thanks a lot for your help. As you say, this confirms what I already knew.

  But we really need keep everything in harmony. So, here is what I did, which should hopefully help someone else in the same position.

  The circuit is very simple, using a FIN1001 LVDS line driver. It is a SOT-23 package. Connections are the following:

  * Din connects to the output of oscillator 100 MHz (TC0-2104, pin 4).

  * Gnd connects to the Earth (C210, lower)

  * + 3v3 connects to the more accessible place, that TCO-2104, PIN 6.  [The 3V3 regulator is on the back of the map]

  * FIN1001 food is decoupled with a 0.1uF adjacent capacitor.

  * Dout + and Dout-are connected to a short (30cm long) of the unshielded, twisted pair made of wire 0.7 mm PTFE. (Z ~ 110 ohms)

  Photograph is attached. The SOT-23 package is physically secure, with a tiny drop of cyano, C210 and mounted on his back.

  The receiver uses a FIN1002 receiver, finished with 100 ohm twisted pair and uses a 74VHC04 to convert 3.3V 5V TTL.

  It is mounted on a 14 pin DIL socket, to plug directly into the socket on the other card PCI which normally has its own oscillator module.

  Result: everything works, and I have a 100 MHz clock available to drive the other timing card.

• HP Touchsmart 310 1125y: installation of USB 3.0 in the Manager of PCI express expansion

  The office, I have a HP Touchsmart 310 1125y, is completelystock other than 2 updates, I did. I installed an SSD and I also upgraded the RAM 8 GB to my computer. I was wondering, is it possible for me to install a USB 3.0 through the location of PCI express mini-map? If this isn't the case, would be to remove the DVD drive and runing slimline sata (13-PIN) to sata (22 pins) in the work of usb 3.0?

  Best, Matthew Dehlinger

  Hello

  When Pan you to connect it to the mother following your machine card?

  

  Kind regards.

• What is the best compatible microSD and the maximum capacity for a Tablet android Iconia 10 One?

  Could someone tell me what is the best compatible microSD and the maximum capacity for a Tablet android Iconia 10 One?

  Two possibilities: perhaps the message is that your actual RAM is low, which means that you are trying to run applications too at the same time. Closing some should help a lot. The other is more likely, and that is the internal memory which is running low. There is a lot that can be done to help that, but it is especially dependent on what is causing the space to fill. If this is a case of too many installed applications (when applications are installed by default, they are going to the internal storage, the SD card is generally used only for data), one or more of the app that fills with things very with log files or personal always data in memory instead of on the DD of the.

  Check first for the last. Make sure that your photos, videos and music are all on the SD card. If you find tham in the internal memory, move them. Make sure you say the applications that use where is the new location.

  Then find the application specific data when it shouldn't be. Many file managers will do for you, you are looking for by flying over or logfiles extra-large. Parameters; Applications; Application Manager (or similar, names depend a bit on OS version) should allow you to look at each application data and cache. Those compensation where appropriate will free up the space.

  Finally, look at the applications that you have downloaded. Are there any that you do not use? If so, uninstall them. Note that the system and preloaded apps in general cannot be uninstalled, but you can often remove updates and then disable them in order to free some space.

  Storage on a device Android always tends toward the back of his head and gets the older unit the problem seems to be. If I were a type of plot I would suggest that Google is encouraged to keep buying us new machines every two years... None.

• Device driver unknown dv2718us in the system compatible ACPI Microsoft

  Gentlemen.

  I have a HP Pavilion dv2718us and I need all the drivers for windows 7 Ultimate 64-bit, the only show of HP in the site for Vista 64-bit drivers, so I have problem. Today I install the unknown in the system compatible ACPI Microsoft device driver, please, send me a link to download this driver.

  Best regards

  Hello

  Windows 7 should fix because otherwise, you try the following link:

  http://www.pcpitstop.com/drivers/download/Microsoft~ACPI-compliant~system.html

  Good luck.

• I can't get my PNY NVIDIA GT 520 to install in my Pavilion a6123w. I set the BIOS to PCIe

  I can't get the new video card GT 520 to stay in the Device Manager list.  I upgraded to a Psalm of 650 watts I set the BIOS to PCIe and also tried PCI.  I have disabled and also tried to uninstall the integrated video graphics card GeForce 6150 nForce 430.  The GT 520 worked twice after I leave the PC closed for several hours unplugged and then boot with the monitor connected to the GT 520 VGA connection.  Both times she came back to the integrated graphics card, which has no red color.  I have the latest driver for the installed GT 520 and he demonstrated to be driven to the integrated graphics card.  When the GT520 was working he executed perfectly and I used it for several hours each time.  The first time it worked until I close the PC (Pavilion Office a6123w) down to try to get the DVI on the GT 520 connection.  The next day, I left the PC for a few minutes after using it for about 2 hours.  When I got home, I had no signal on the screen.  I went from the connection to the integrated VGA and was back in the video.  It's the second GT 520 I tried, the first was returned to Fry, because the customer (?) support PNY suggested it might be a bad card and that I should up grade of PS.  I hope someone knows the specific steps to take to make the stay of GT520 as the main graphic.  I saw a suggestion on a site that said there may be a jumper or a way to disable the video edge physically.

  Oldwrench, welcome to the forum.

  I would uninstall all (driver, video card) that you have done and start over again.  I suggest to use Revo Uninstaller to remove the driver. I always use the advanced option. This will remove all files from the registry and hard drive.  Then, restart the system.  This should put you back where you started.

  When you install the discrete video card, integrated graphics subsystem should be automatically disabled.  Makes no changes in the BIOS.  This could be the cause of some problems.  Once this is done, you can install the latest video driver from nVidia.  Restart the system and see what happens.

  If your problem is solved, please click "accept as a Solution.

• What makes the incompatible compatible

  I tried to connect my Lexmark X 83 printer/scanner to my laptop but it won't work by saying that my printer is not compatible with this version of windows. (Unfortunately I do not have installation disc either.)

  Is it possible to make the incompatible compatible? Can I download something or do something to make it work?

  Thank you!
  -the desperate student for a printer to work

  You can't make Compatible with Vista drivers.

  Lexmark has drivers, or they do not.

  http://support.Lexmark.com/index?page=Home&locale=en&UserLocale=en_US+.

  The Lexmark site to check for Vista Compatuible drivers for your printer model.

  See you soon. Mick Murphy - Microsoft partner