BSOD, unable to erase the hd.

Similar Questions

• Unable to start the computer - boots of BSOD

  Dell Dimension 210/9200c Windows XP Pro SP3 desktop

  Here's what I spent...

  Start-up, enter the admin password.

  Floppy drive seek failure

  Strike F1 key to continue, F2 to run the utility series

  If I choose the F1...

  Loading PBR for descripto 2... In fact.

  Playing a disc error has occurred

  Press CTRL + ALT + DELETE to restart

  I press CTRL + ALT + DEL and it leads to FAILURE to SEEK the FLOPPY DISKETTE.

  If I choose to F2, it goes to creating useful and I don't know what to try to change the problem.

  If I press F12 and go to the start menu...

  SafeMode to start the BSOD

  I tried to boot from the CD and use my recovery CD and the result was...

  Window, set up ran with the establishment is responsible (file exchange...), then he went up to the game starts windows.

  Here's what came...

  A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS SHUT DOWN TO PREVENT DAMAGE.

  IF IT IS THE FIRST TIME YOU'VE SEEN THIS STOP ERROR... RESTART YOUR COMPUTER

  CHECK FOR THE PRESENCE OF VIRUS.  REMOVE ANY NEWLY INSTALLED HARD DRIVES OR HARD DRIVE CONTROLLERS.

  CHECK THE DRIVE FOR THE CORRECT AND COMPLETE CONFIGURATION

  RUN CHKDSK/F TO CHECK FOR HARD DRIVE CORRUPTION, AND THEN RESTART

  TECHNICAL INFO:

  STOP: 0X0000007B (0XF78DA63C, 0XC0000034, 0X00000000, 0X00000000)

  I can't the system to start.  I haven't added hardware or software.  I think that the computer has restarted after downloading some updates, but I can't to start or restore system. What can I do?

  Yes, I can get to this screen.  After you have clicked on enter, it looks like this:

  SET UP WINDOWS

  __________________

  __________________

  downstairs "SET UP IS LOADING FILES (*)...

  Then it turns down in "SET UP START WINDOWS"

  Then, it goes straight to the BSOD.

  I tried several times and he always goes for the BSOD.

  In the menu Setup, I ran a hard drive diagnostic and it showed this:

  "RUNNING HARD DRIVE DIAGNOSTICS, PLEASE WAIT...

  DRIVE 0: ST3320620AS

  IN CASE OF FAILURE.  RETURN CODE: 7

  Is this to say that the HD is shot?

  Your hard drive may or may not be at fault. Error code 7 could mean just corrupted hard disk controllers. This could also be the reason for the bsod.

  Enter your bios and follow the instructions below.

  1. start-up (Dell logo), press F2 to enter the BIOS

  2. expand the section "readers".

  3. go in "SATA Operation."

  4 change that "RAID Auto/AHCI" to "RAID Auto / ATA.

  Furthermore, if your bios does not have this option simply switch from SATA IDE mode.

• px12-350r unable to join the domain - what now?

  Hi all!

  I hope you can give me some advice because at the moment I'm in a really silly situation, being probably locked out of my Iomega px12-350r.

  Here is what happened:

  * The device was successfully linked to my domain name Microsoft AD and worked with this config at least a year.

  * I expanded the storage matrix, 2 days adding 2 drives. Everything went well and the end of the expansion, the new total disk space is displayed correctly in the web administration interface.

  * After this, I restarted the device. After the reboot, I couldn't connect to the device more using my domain account. This account had administrative rights on the NAS and I connected on the NAS using this account before.

  * I don't alter the domain infrastructure.

  * I know that the device cannot join the domain more because I enabled e-mail notifications and he continues to send me "unable to join the domain".

  I have already tried:

  * Connection using the usual accounts: doesn't seem to work once the device is connected to a domain.

  * Connection via SSH. Does not work, probably for the same reason as above.

  I wasn't yet:

  * The user manual mentions reset the admin password by pressing the reset on the back button. But this will only reset config (I'd be okay with it), or it will erase the data on the drives as well?

  I'm from the Germany. Despite having purchased a service plan 24 x 7 hotline support German will only redirect me to the hotline American which claim to do only office, no SIN px12. I'm kinda in the middle of nowhere now. ;-)

  Thanks for your help!

  Best regards

  Florian

  Hi André,.

  I fixed it without reboot - by chance.

  In a desperate attempt, I tried to connect using the domain administrator account - and it worked! I don't remember giving any px12 admin permissions to this user and I certainly don't connect to the device using this user before. But the account has permissions to create computer accounts in the ad, and in the moment when I logged in the computer account of the AD px12 updated password.

  I tell myself that the px12 has used the account admin for re - joining the domain. From the web interface, I could now do a sync AD and after that, all users of domain reworked.

  So, if anyone has the same problem, try connecting the device with any account that has administrative rights on the whole of the field, even if you have not used the account on the device before. It can work for you, too.

  Local accounts still do not work. I think that if the device is connected to a domain and the domain link is broken permanently, so it's only the reset button.

  Andrew Merci for your support!

  Best regards

  Florian

• What should I do when I receive the message 'unable to load the flash shockwave.

  What should I do when I receive the message 'unable to load the flash shockwave.

  Hello

   
  1. how many times you get this error message? This problem is limited to specific Web pages?

  2. Once you get this error message? What is your default browser?

  
  Find out what version of Internet Explorer you are using
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using
  
  3. have you installed new hardware or software before the show?

  4. What is the operating system installed on the computer?

   
  5. are you logged in as administrator?
   
  
  Method 1:
  If you are facing problems with Internet Explorer 9, I suggest you read the article and try to run theFix it:
  Troubleshoot Internet Explorer to IE quick, safe and stable
  http://support.Microsoft.com/GP/pc_ie_start
  Note: Note that the reset Internet Explorer (IE) resets all settings defined by the user, including those established by the installed extensions, toolbars and other add-ons for IE by default. This includes all the security, privacy and settings area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.
   
  Method 2:
   
  a. search for Internet Explorer in the start menu.
   
  b. right click and select "Run as Administrator".
   
  Check if the problem occurs.
   
   
  Method 3: Uninstall and reinstall Adobe Shockwave
   
  To uninstall a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program
   
  
  I also suggest you to download and install the latest version of Adobe Shockwave player and check if that helps:
  
  http://get.Adobe.com/Shockwave/
  Provide more information about the issue so that we can better help you.
   
  I hope this helps.

• When I hook compruter to the tv it works but it does not not to erase the s video cable

  When I hook compruter to the tv it works but it does not not to erase the s-Video cable

  Hello

  1. are you unable to connect the TV to the computer via the S-Video cable?

  2 what exactly happens when you try to connect the S-Video cable?

  3 how you have connected the TV to the computer?

  4 do you encounter issue with the clarity of the video when it is connected with the S-Video cable?

  Please provide more information on the issue so that we can better help you.

  You can also visit the link of the article of Microsoft that will guide you on how to ask questions below.

  Suggestions for a question on the help forums

  http://support.Microsoft.com/kb/555375

• Windows 7 Home Premium 32-bit OS is unable to complete the installation.

  Windows 7 Home Premium 32-bit OS is unable to complete the installation.

  I have a Dell Inspiron 530 of 2007 which came with Vista and has been updated 2 years later at 7 w. I had to reinstall 7 W... 3 or 4 times since 2010. I guess that my machine can't handle W7 very well.
   
  My current problem started with a BSOD problem. After trying some suggestions Internet on how to solve this BSOD problem that did not work, including repair of Windows, I did a data back up mode without failure and then decide to reinstall Windows 7 from the MS CD. My level of understanding is limited, but as noted, I've done this before with success. What I didn't understand is there seems to be another unsolved problem which does not allow the complete reinstallation of windows.
   
  I did a clean install, then a formatting and in both cases, W7 could not complete the installation. It progresses to the final stage of "complete installation" and then there is a second error message 1 that I can't read... "" a problem has been detected... close... "."  It seems to be a reboot loop.
   
  I have since read that the original BSOD problem and the 'detected problem' could also well be linked to the display driver. And this driver it must be disabled before performing a Windows installation. But I'm not able to access Safe Mode or the control panel to turn it off. If this driver is the problem, is there another way to turn it off?
   
  Or are there any other suggestions on how to complete the installation of the operating system?
   
  Thank you.

  I see that you have posted on the Dell desktop Forums and Robert (rdunnill) gave you a suggestion. He is the expert forum on upgrade/repair of equipment in Dell desktop computers:

  http://en.community.Dell.com/support-forums/desktop/f/3515/t/19632098

• Unable to kill the task of Consolidation for HFM application

  The user is unable to kill the task of Consolidation in HFM application. Consolidation process that lasts 2 minutes did evidence of State that execution of @79 % for 4-6 hours. The user ID is a configuration manager, to lock the data and unlock the provisions of common data Services. The task button in the list of running tasks is not enabled. Our support team has helped users access which is not as able to stop the task. Please Note Access Admin is limited and not allowed for these tasks.

  I would check the HFM log to see if you find anything referring to blocked documents locked.

  If your HFM application is killed in the middle of consolidating or perform other activities that requires him to "lock" a memory segment in the database, that "lock" is maintained on these data points when the application restarts.

  If you then try to make an another codification and it hits one of these points of data locked, it will sit there for a very long time waiting for the "lock" erase.

  I forgot the exact error message that you will find in the newspaper AND I forgot the time-out; However, it sucks having to wait over there.

  The other possibility that comes to mind is that really abandoned building and the State has not updated. (once more check the logs)

  Charles

• Can't erase the history of Safari completely

  So somehow, I managed to set up the date to December 31, 2100. The only problem is that I opened YT in Safari and now I can't erase it from history. When I remove and reopen Safari it comes back. I tried to erase the history, but it did not help. However, it seems that it has disappeared from my Mac, now I can't remove it to iOS.

  There are solutions to this problem?

  Yes, I absolutely do not learned to play with the date.

  Settings/Safari/clear history and data from the Web site does not work?

• updated Mac and now I am unable to answer the phone calls of the Mac

  Yesterday I updated my Mac to the new operating system.  Since then, I could not pick up calls from the Mac as I used to.

  Can someone tell me how to solve this problem?

  Hi jlfrisella!

  I see that you are unable to use the calls feature cell phones iPhone on your Mac since the update to Mac OS Sierra.  I can understand wanting this function runs on the right, and I'm happy to help you.  Please see requirements and instructions in the following articles.

  Continuity of use to connect your Mac, iPhone, iPad, iPod touch and Apple Watch

  Thank you for using communities of Apple Support.

  See you soon!

• Unable to get the song on ipod

  I opened it in iTunes and got 51 Wav songs on it but it wouldn't hold any more. I then went online looking at a manual, and I realized I needed to convert songs to a lower compression.

  I formatted the iPod and then tried to compress some songs, but I can't figure out how.

  I need quick tips because if I can not all the songs on it I have to take this and switch so I can have the music while I'm out of town for the next 5 days.

  Thanks in advance

  When you say "formatted", did this using Windows?  Because that completely erases the iPod, including its software shipped necessary to operate as an iPod.  The right way to erase an iPod is to do a restore via iTunes, which implements (after deletion) condition 'factory' by default.

  When you connect it now (with iTunes running), the iPod still appear in iTunes?

  Are your 'Wav 51 songs"in your library iTunes music?

• Erase the iPhone 6, iOS 10 to negotiate?

  I was in a hurry and do not pay attention to all the steps when I was preparing my phone to trade. I disabled the parameter "Find my iPhone" and then "erased all content and settings", then packaged upward and sent to Verizon. I didn't sign icloud first.

  My question is, I'm having a problem?

  No, if you have disabled find my iPhone. You can check it out by going to iCloud.com on a computer, open find my iPhone and see if your device is still on display. This it is, and it is connected to Wifi, you can select it and delete it again. It will ask you your password ID Apple/iCloud, and which will disable and erase the device. If you remove an instrument - this means that find my iPhone has been disabled. I wouldn't remove the device at this point.

  Once you are sure that Verizon is to have no problem with your device, you can then remove it from your iCloud account. But better not to do it until you get the all clear on their part. Easier to solve the problem if you are always bound...

  See you soon,.

  GB

• How can I erase the data on my laptop before I give it away?

  How can I erase the data on my laptop before I give it away?

  See this document.

  https://support.Apple.com/en-us/HT201065

• Unable to see the comments on Huffington Post

  In version 41 and earlier versions, I could see the comments section of the Huffington Post with no problems. With the recent upgrade to the 42 version and now 43b 04, I am unable to see the reviews online. I installed a previous version (b 41, 09) and they were there without changing my settings; If something has changed within Firefox.

  private browsing mode has always meant that firefox doesn't store information from your session locally on your device - now, it is also associated with blocked content on Web sites.

  more: the service-not-track allows you to communicate your preferences to not follow to Web sites, but it is for them if they respect it and follow on this subject. the new follow-up mechanism necessary actively blocking connections with elements that are deemed be trackers...

• Unable to choose the range in iMovie

  Unable to choose the range of iMovie 10.1.2

  Hi, Jeff.

  You can select a range inside a clip with your clip in the timeline, placing your cursor on it and hold the 'r' key when you drag your cursor over the clip while pressing your mouse or track pad.  The range will be described in a yellow box.

  To select a range of multiple clips, select the first clip, and then select the last element while holding down the SHIFT key.

  Best,

  -Rich

• Unable to put the bookmark bar on the page after your last update

  MONITORING INDICATES TO BOOKMARK BAR BUT IT WON'T SHOW WENT TO CUSTOMIZE BAR BOOKMARK CHECKED AND CLICK ON CUSTOMIZE AGAIN WHICH SHOULD PLACE IT UNDER THE SEARCH BAR BUT DOES NOTHING. THIS HAS HAPPENED AFTER YOUR LAST UPDATE.
  ANY IDEA?
  Thank you

  Hello

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that temporarily disables hardware acceleration, restores some settings and disables add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • Click the menu button

    

    click Help

    

    then select restart with disabled modules.

  If Firefox does not work, you can start Firefox in Mode safe as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the problem is not present in Firefox Safe Mode, your problem is probably caused by an extension, theme or hardware acceleration. Please follow the steps described in the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

  If this does not work, maybe it's time to try refresh (called "Reset" in older versions of Firefox) which can resolve many issues by restoring Firefox as his default from factory and save your bookmarks, history, passwords, cookies, and other essential information.

  Note: When you use this feature, you will lose all the extensions, toolbar customizations, and certain preferences. See article Firefox Refresh - reset modules and parameters for more information.

  Refresh for Firefox:

  1. Open the troubleshooting information page using one of the following methods:
     • Click the menu button

       

       click Help

       

       and select troubleshooting information. Should open a new tab containing your troubleshooting information.

     • If you are unable to access the Help menu, type Subject: support in your address bar to bring up the troubleshooting information page.
  2. At the top right of the page, you should see a button that says 'Refresh Firefox' ('reset Firefox' in older versions of Firefox). Click on it.
  3. Firefox closes. Once the update process is complete, Firefox will display a window with the imported information.
  4. Click Finish and reopen Firefox.

  This corrects the problem? Please report to us!

  Thank you.