at the same time start the VI

Similar Questions

• D7260: two problems at the same time - started paper jams and ink intermittent problems

  First of all, let me say that the printer is out of warranty.

  Paper jams – there is nothing inside the printer. Looking at the back of the printer there is a point inches long finger inside the printer (far left) plastic just above the document that grabs the paper and photo paper.  Each paper and photo paper that goes through the printer grabs on this extension and ends with a truncated top left corner after printing.

  Intermittent problem of ink - sometimes magenta will not print, sometimes black doesn't print, sometimes, they all will be printed.

  I am ready to throw this printer out, but before I I want to take it apart.  I want to take the cover off, but there seems to be no easy way to do it.  Can someone tell me how to remove the cover?  There seems to be two screws at the back of the printer that needs a tool small, hexagonal, but there also seem to be some pins plastic all around the bottom which can have simultaneous "pressing" need to release the tabs.

  Any ideas? Don't forget, I am ready to throw this clipboard outside, but I don't want to take a "sledgehammer" to take it apart.

  It did not work.  Paper/transport jams now.  Magenta ink still does not print. This printer is worthless.  I get an Epson printer for photos. This printer D7260's official "junk" now and will be thrown...

• After the update to Firefox 16.0.2 flash vid to youtube started to freeze and plays a few seconds and freezes again, at the same time my computer crashes also?

  This only occurs in firefox 16.0.2 but not in chrome. In the Task Manager, I see FlashPlayerPlugin_11_4_402_287.exe 2 times and 2 times plugin - container.exe. At the same time my cpu starts to rise the temp and the computer freezes. Everything starts to work when I close flash video in youtube. Firefox functioned well before the last update for 16.0.2.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do not click on the reset button on the start safe mode window or make changes.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

  You can check the problems caused by the recent updates of Flash and try these:

  • disable an eventual extension of the browser for Firefox Plugin RealPlayer Record and if installed RealPlayer update
  • disable the safe_mode in Flash 11.3 and later versions
  • turn off hardware acceleration in the Flash plugin
  • http://KB.mozillazine.org/Flash#troubleshooting
  • https://support.Mozilla.org/KB/Flash-113-doesn ' t-charge-video-firefox

• Windows 7 Enterprise random screen in white at the start of laboratory of computers at the same time

  We have several laboratories in the school district where business customers with service pack 1 windows 7 random would be white screen if the laboratory is started at the same time. If the network cable is unplugged, it doesn't. This happened over several years, devices have been recreated, drivers have been updated always the same question. Different model were used at HP with the same result. Software LanSchool is used to start the devices into the holder. I tried to start all lab with WOL problem persists. Students have tried to start the lab at the same time, same problem. Confused about what is causing this problem. Network is on each apparatus and the uplink 1Gps. Several bones of different switch have been tried. No newspapers or port switch off common errors.

  Hello

  Thanks for posting your question on the Microsoft community.

  The question will be better suited to the audience of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet forums.

  TechNet Forum
  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Thank you

• WMP 12 plays 2 songs at the same time. If a piece is played and I spend almost another song, the second song starts to play and the first

  A frustrating problem with wmp on my new laptop of ASIS Windows 7. During playback of an mp3 file, if I hover near a second file, the second file starts to play in the first.

  The system is used for dance classes, and I need to have the ability to choose a second track spontaneously.

  This does not happen with the previous version of wmp (11).

  The problem would be the touchpad on the laptop?

  Charles Todd

  Hi Charles,

  The description of the problem, it looks like Windows Media Player plays 2 different songs at the same time when hover near a second file in Windows Media Player.

  You can run the troubleshooting Windows Media Player Settings Troubleshooter & check if the problem persists.

  Troubleshooting of Windows Media Player settings

  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Please come back with more queries on Windows, we will be happy to help you.

• Windows has started to put some files in two places at the same time, will appear in some programs

  Hello

  in the last two weeks, I noticed that Windows (I use Windows 7) began to act up with its allocation record. First of all, I noticed that a new folder I created for some music files was not detected when I tried to open the file in a music editing program (Adobe Audition). If I created a new folder in a different location and copied the files into that, suddenly hearing would recognize the folder. Change a few days I noticed that in addition to this, when I copied a disc into my computer, after you select a new folder for the files to copy, Windows would create a second copy mirror of the folder and the files and place it in another location not of my choice (this all happens within my music library folder). Some files that I had cut my folder "work on", to stick to my folder to archive tips that did it, and windows in two copies of each of them - one where I had pasted it and other oddly in a separate folder completely in my archives. For some reason any Windows decided to put copies ghosts of several things in this folder without special report. So, if I change the files in a folder, they are automatically changed on the other; If I try to delete a copy of this file, it removes the two; and if I try to cut and paste the lot assigned folder and put it where it should be back (IE if there is already the original copy) Windows says it can't do that because the destination file matches the location of origin. I don't know how to remove these files has doubled up foreign, which create a lot of confusion trying to figure out where my files and which ones to change. I can't find any way or return of Windows to its appropriate classification system, including maximum until recently had none of these problems.

  Music library is not a folder, it's just a definition of research.

  Libraries are really just XML files that define search criteria.

  The real essentials you need to know is that libraries are not records.  They are really just a quick search of several places.  Try this: right click on the document library and select Properties.  This will tell you where the library is looking.  Whenever you open the document library, it performs an instant analysis of these places and tells you what he found.  Is not additional copies files, it's just search results. If you delete something, you remove the one and only original, everywhere where it is.

  You might ask "well, what's the point of a library?  I'm glad you (perhaps) asked.  The reason is you have a lot of places.  Take me for example.  I have some movies on my hard drive.  I have more moves on an extra drive (they will all take place on the main drive).  In addition, my roommate has a few movies on his drive.  With a library, I have a library of videos that research on all drives and gives me a single view combined all our movies instantly.  Now I can see all my films in my library at the same time, no matter which disc they are on.

  The files are not duplicated or moved, you see just a list of them, such as a telephone directory or the Google search results.

• Remote start esxtop mutiple hosts at the same time?

  Hello people,

  I'm trying to figure out how to take this esxtop command:

  ESXTOP d 10 - a-b - n 6 > /tmp/cs242_esxtop1.csv

  .. .and convert it for use with get-esxtop-Server esxhost1 and PowerCLI.

  This perhaps is that I could call get-esxtop mutiple times in a script on multiple servers at the same time.

  Check if anyone has suggestions or comments?

  Thank you

  romatlo

  No response.  Will close.

• Download all the songs at the same time

  I have 3 400 + on my Apple Phone music and just got an iMac. I want to download all the songs in iTunes on the hard drive. What I have to download every song or album individually or is there a solution with a single right click download them all at the same time?

  Better would be to transfer them from your old computer to the new. In this way, you would hold playlists, ratings, etc.

  Download all the songs match [iCloud] both - https://discussions.apple.com/message/18223535#18223535

  Ludovic August 2015 message: https://discussions.apple.com/message/28692305#28692305 .

  "Choose the music.

  Select Tunes Store.

  Select bought on right side.

  Select not in my library.

  Click Download all down right. »

  Page 6 of Apple, more meticulous instructions step by step: how to move your iTunes library to a new computer - https://support.apple.com/HT204318 it is convenient if you think that all your materials are not in the standard location.

  My resume in a sentence if you use preferences by default iTunes settings: copy the folder integer iTunes (and to ensure that all of its subfolders and files) intact at the other disk, hold down the option/alt key (shift on Windows) keys to start iTunes and on request to select a library select iTunes Library.itl file in the copied folder (open a different iTunes library file or create a new one - https://support.apple.com/HT201596).

• More often than in other music Apple will not be broadcast on my iMac, but at the same time, it will be on my iPad

  I am continually frustrated with Apple's music streaming on my iMac.  Looks like a song loads, but never gets started playing.  I always thought the problem was my internet connection, but lately I discovered that, although my iMac does not load a song, if at the same time, I use my iPad on my wifi it loads and plays immediately.  What is the problem with the music does not not on my iMac?

  Hello Lucyskye,

  Thank you for asking your question here in Apple Support communities. I understand you want to be able to play your music. I can't do anything without my music all day. Let me give you what I can to help you solve this and get your music to play on the iMac.

  I don't want to bring music to Apple implemented correctly first. Apple's music composition only allows you to stream music from Apple on one device at a time, unless you have a family membership. Even if you have a family membership, you can still only broadcast on one device at a time by Apple ID. For this reason, I suggest isolate us the devices first and this test with the iMac.

  1. exit the Apple music on the iPad. Please leave the app. You can do this by double tapping the home screen and drag the application to the top music. This article has the instructions and example pictures. Force a nearby application on your iPhone, iPad or iPod touch

  2. restart the iMac.

  3. If the problem persists, start the iMac in Mode safe mode and see if the load and play songs. (Although the speakers will be disabled, just visually see if she manages to go anywhere where it usually hangs up on. This article talks about fashion without failure: try safe mode if your Mac does not start-up

  4. you want to then also to test in a Test user. This article helps with that. How to test a question in another account on your Mac user

  If the problems remain and music will not play on the iMac in Mode without failure or user Test, then we want to stop the iMac. Back to the iPad, then click Settings > cellular and disable cellular data for a while. Make sure your iPad is only able to use a Wi - Fi connection and not able to access cellular data if the songs will not play on your Wi - Fi network. Then, open the app music again and try to play a song.

  If the music will not play one cell time is off, the cause is some parameters with your wireless network. You can check this information for the most common causes of problems with home networks. First of all, make sure that you use a wireless network open as your home network. If you connect to a Wi-Fi as a school, work, or other business, the airport, a military base or a hotspot of a network type, it probably won't work because these types of high security and high traffic and high security networks. They do not have the necessary data back causing problems exactly like the one you are currently experiencing.

  Do you use any third-party firewall (even on the router!), protection against viruses or proxies (which hide your identity on the internet)? Some security applications also do, but are called only for security or VPN. These few apps with names like Astrall or Webroot Secure Anywhere Antivirus, antimalware apps. There are literally hundreds of these applications that block the incoming ports that will not allow the function runs.

  If you want to check that the port is open on your iMac and the network, you can use this article: port TCP test between computers and peripheral connectivity. Apple music uses port 80, and iTunes music sharing is port 3689. You can find a list of all the ports used by Apple here: TCP and UDP ports used by Apple software.

  You can also find these two useful articles if you find that the problem is with your network.

  Recommended settings for the WiFi routers and access points

  Solve the problems between iTunes and third-party security software

  Don't forget to turn your cellular data within settings > cellular on the iPad once you're done test. Just in case music plays in Safe Mode or the Test user, you work through this article to resolve the issue. Mac OS x: how to solve a problem of software.

  Thanks again and have a great rest of your day!

• You can use the activity tracker and an application running at the same time?

  I've been running just with my watch and the Apple activity tracker.

  But I wanted to calibrate so tonight I ran with my iPhone, too.

  I tried to use the Nike + and the PPP of activity both starting on my watch. I ran with the application of the activity on the screen.

  When I did I stopped the activity app and went to the Nike + app, but it was stopped.

  Then can you run the application of activity and a different running application at the same time. Or do you need to start another app on your phone and activity on your watch?

  Thank you all

  Hello

  To save your route at the same time apps, save the workout using the application of the workout on your Apple Watch (early check it there first) and also through the application of Nike + running on your iPhone.

  Monitoring of your training via the integrated application of the watch workout will cause your heart rate to be monitored at all times for the duration of your workout.

  The app Nike + running cannot currently access heart rate monitor watch directly, but if I read the heart rate data of the health on the iPhone app, it will always be able to access - indirectly - the same heart rate for your exercise data:

  -On your iPhone, in the application of health, press Sources (tab) > Running > turn on Allow 'Running' to read heart rate data.

• At the same time, both Firefox (with images, the other without)?

  Hello

  Is if possible to use two browsers firefox at the same time, one with active images, the other is disabled?

  Easy way on Windows: you'll need 1) the name of the second profile you have created, 2) a shortcut existing (already on the desktop, I hope) to Firefox.

  1. Create a copy of the shortcut, you can right-click on the shortcut and select send to > desktop. It will create a nice copy of second.
  2. Right-click on the copy and go to properties.
  3. In the 'Target' box, you should see something like "C:\Program Files (x86)\Firefox\firefox.exe" .
  4. After all (including the quotation marks) in the target box, add -no-remote -P <profile> where <profile> is the name of the profile that you created.
  5. For example, if the path to the firefox.exe am I guessed above, it would look like"C:\Program Files (x86)\Firefox\firefox.exe" -no-remote -P my-second-profile

  To run the second instance at the same time, simply use the new shortcut. The -no-remote flag tells him to start another process of Firefox, instead of simply to open a new window in the current.

  Never, ever run two separate processes with the same profile. This is the case, if evil.

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Cannot connect and use 2 hard drives Canvio de Store.E at the same time

  Hello

  I have 2 devices Store.e Canvio: 2 TB and 3 TB respectively but it seems that I can't connect/use them at the same time, as if I do it, one of them (the last I connected), becomes inaccessible ("access denied").

  If I disconnect the first device I connected, the other starts to work,

  Is an odd question, and I can not find someone to live something similar...

  No idea how could it be the cause, or how can I solve it?

  Thank you

  I m wondering if the same problem is displayed using another computer or another USB hub with an additional power supply.

  From my point of view of the few this problem could be related to the low power provided by a single USB port.

  The two hard drives seem to support the USB 3.0 standard.
  The USB 2.0 port common provides 500mA and USB 3.0 requires 900mA
  This means that two USB devices connected simultaneously use 1800mA which could be too much for the USB ports for s laptop

• Satellite A65-S065 - button Power LED is blue & amber at the same time

  1st off I have a S065 A65 and worked well after a replacement motherboard, my fault, he had to be replaced.

  In any case, I have the power button LED is blue & amber LED light up at the same time. Anyone has any idea as to what it means, or maybe I'm going into something, I don't know what it is and it should be reset at the back. Any ideas?

  Thank you
  Ben

  Hello

  I checked the manual of the Satellite A65 and there I can find information that the Power LED blinks orange indicating the machine is in standby mode. So for me it sounds like that your laptop is in sleep mode.

  What happens if you click Start > stop and choose the closing down in the menu drop-down? Normally, the power LED button must be turned off and also the laptop is in sleep mode.

• Some profiles running at the same time, others are not

  I have three 'profiles' that I use for firefox (a general, a working one and locked). I can load them with the '-p' option on the command-line very well. If no firefox runs, and then one of them works perfectly. So I think I have the basics working properly.

  However, two of the profiles (work and general) does not work at the same time. But that locked will run with either of the other two. I cannot understand why and I'm looking for some clues on the newspapers to activate or to debug levels to raise or parameters to twist inside (or outside) profiles.

  Specifically, by "does not work", I mean that if 'general' profile firefox is running, so if I start my work profile (i.e., "PEI working firefox"), he has just opened a new window on the current general profile. If I open the locked profile (i.e., "firefox Pei lockdown") which appears fine (starts a separate instance of firefox, with its own plugins and whatnot).

  I had this problem for a long time (many version of Firefox, before even the 3.0, I think). I have this problem on Windows (but WinXP and now Win7).

  I am comfortable with tweaking the settings and looking through the logs, but not sure what to activate. Google searches have not been successful (it seems to be relatively few people using Firefox profiles).

  You can get Firefox to run different profiles simultaneously by adding-no option command line remotely and more of the P-

  For more information, see opening a new instance of your application of Mozilla with a different profile - MozillaZine Knowledge Base