Audition 3 seeing pricing different sample than that the device presents

Hello

I just installed Adobe Audition 3 and 3.01 patch, on a brand new system running under Windows 7 64-bit. The motherboard is an Asus Sabertooth X 58 using Realtek High Definition Audio. Device drivers show that for line input audio sampling rate is set to 24 bit 192K. I wanted to put up the sound card would test the performance and audio quality.

The problem is when I raise Audition 3 and hit record, I get the message 'we don't support recording when your file does not match your hardware sampling rate. Current hardware sample rate is 44100 Hz." Clearly, this isn't the case since the line properties - Advanced tab displays "2 channels, 24-bit, 192000 Hz (Studio quality).

According to the installation of the audio of the hearing, it shows only one choice for Audio Driver: Audition 3.0 Windows Sound. It also displays the sample rate: 44100 Hz, clock Source: internal buffer size: 2048 samples with no way to change these values.

If I click the button on the Control Panel, I get:

DirectSound input ports:

Device name: line (Audio device high definition)
Audio channels: 2
Bits per sample: 16

Anyone know how I can change these settings to get the hearing agree with device settings?

Thank you

Dale

DaleChamberlain wrote:

Anyone know how I can change these settings to get the hearing agree with device settings?

I'm afraid that life is nowhere near as simple as that. The main issue here is that hearing, in common with most of the audio software, uses a system of driver called ASIO to speak with the audio device - it will cancel much of the operating system and significantly reduces the latency of the system. There are several problems with ASIO if - the first being that it supports only one device per system (or sometimes multiple devices identical if the manufacturer can make look like a single device) and with software designed to use this driver, then to use any other driver (like a native Windows) you must use a converter like ASIO4ALL step. This convert the ASIO WDM Stream and allow you to use multiple devices sound - but with an increase in latency.

That's the second problem that will really you stuff well - and it's quite reasonable, ASIO is limited by its inventors to run only three sampling frequencies; 44.1 k, k k 48 and 96. So there is no way you can run that you think that may be a higher quality setting. All of the above parameters even 48 k make your audio device much more difficult work and what for? All that happens is to increase the potential bandwidth to well beyond the range of human hearing - to no purpose at all. You do not have sources that can produce useful at these frequencies output, and you certainly do not have the means to reproduce. This all is well documented and explained before, so I'm not all that again. In a Word, Nyquist points out that any device digital sampling has a bandwidth limited to a maximum of half of the sampling frequency, for 48 k which gives us a frequency upward to 24kHz response - comfortably more high that any adult can hear from far away. Whatever it is you enjoy and save out of it using the same 96 k nothing but noise is as far as humans are concerned, and unpercievable of noise to that.

What says the line properties tab is so, if you have a no ASIO driver designed to support all the possible, possible rates. You don't have an ASIO driver is available, because it is a built-in audio device, and anyway you have already pointed out that it uses the Windows driver for the hearing (a lighter version of ASIO4ALL, actually), so a conversion is already underway. Call Realtek as "High Definition Audio" does not exist - all audio devices built of this nature exist to universally of poor quality and improve it that you would need an external device - which are numerous, usually with ASIO drivers dedicated. But none of them works with ASIO beyond 96 k, everything simply because the standard does not support higher rates.

If you download and use ASIO4ALL (it's free), then you will get a control panel extra that will show you exactly what your audio device is able to do as much as hearing or any software ASIO is concerned, it is a useful diagnostic tool anyway, so it is better to do. Simply select this option during installation, instead of hearing Windows driver.

I'm sorry to be the bearer of what appears to be bad news, but in fact, it is not. You won't see any difference in quality at all the clocked at something beyond 48 k sampling frequency; everything you do needlessly wastes the resources of your computer. Waste you the resources processing and disk space available by treatment at ridiculously high sampling rate, and there are zero returns.

Tags: Audition

Similar Questions

  • How can I get my computer my external USB drive (portfolio) after that I repeatedly get the message that the device "can not be removed?

    Original title: I need a market to resolve the problem remove the instrument.

    How can I get my computer my external USB drive (portfolio) after that I repeatedly get the message that the device "can not be removed? I have closed all other programs and waited for varying amounts of time, and tried all of the fixes that have been proposed on this site. Nothing works. I don't want to turn off the computer whenever I have to remove the device.

    I can't know what "all patches" you've tried, but:

    Make sure that the system restore does not monitor the external drive.  SR does need to control the system drive and to the system drive, SR has only about 1 GB of space max.  Make a right click my computer and select properties then the System Restore tab to configure SR.

    Make sure that the Indexing Service is turned off (at least for the external drive).  To disable disk indexing completely, which will also speed up your computer a bit, see http://lifehacker.com/031440/turn-off-indexing-and-speed-up-windows-xp.  For the external drive, right-click on the drive icon in my computer, select properties and uncheck the indexing disc

    There are different workarounds short to shut down the computer, but you might want to try this third-party app first:
    http://safelyremove.com/index.html  Among other features:

    The device cannot be stopped now. Why? Never encountered the situation when Windows does not allow you to remove a device? Unlike Windows, USB remove will show you programs which prevent the device to be stopped and let you close these programs or just files that they opened on the device.

  • I have laptop Toshiba and windows 7, but my webcam is not working it shows that the device is locked by another application.

    I have laptop Toshiba and windows 7, but my webcam is not working it shows that the device is locked by another application. Help me please!

    For a built-in webcam see this support from manufacturers or their forums.

    You could I think trying a boot minimum http://support.microsoft.com/kb/929135 and see if its then OK

  • Im having problems to connect my helmet at the entrance in front of my laptop, and I can't use my microphone, which says that the "device" is not connected.

    Hi im having problems to connect my helmet at the entrance in front of my laptop, and I can't use my microphone, which says that the "device" is not connected. What should I do? Thank you

    Hello

     
    1. have you checked the problem by plugging the headset to another computer?
    2. it worked before?
    3. What are you talking about ""device"is not connected?
     
     
     
    I suggest you to connect to another computer and check.
    Also check if the device is compatible with Windows 7.
    Reference:
    Windows 7 Compatibility Center
    If it's compatible, perform the methods below
    If it is not compatible, see the following articles:
     
     
     
     
     
     
     
    Method 1: Run the audio Troubleshooter and see if it helps.
     
     
     
    Method 2:
    Run the Fixit described in the article and perform the steps:
    See also:
     
     
     
     
     
    I hope this helps.

  • What can I do if I found an iphone and that the device is erased but still linked to account of the former owner.

    What can I do if I found an iphone and that the device is erased but still linked to account of the former owner. ?

    Call your local police.

  • Adding a device:-201401. Make sure that the device is connected?

    I was able to set up my Explorer Measurement & Automation to detect my device (NI cDAQ-9188), but I'm unable to add the device.  The error statement says:

    Add the device failed.  From the device driver error report is as follows:

    Add a device

    -201401

    Recovery of the properties of the network device failed.  Make sure that the device is connected.

    How can I fix this so that I can test my modules e/s?

    DAQmx version: 9.7.5

    Operating system: Windows 7 64-bit

    Initially:

    In the tab network adapters, it reads:

    -No network adapters found

    In the tab of the firmware, it reads:

    -firmware version: 1.1.0f0

    Based on the status of the network configuration tab, I assumed that my problem was related to the network connection.  I have reset my network cards and this seemed to solve my problem.  Thanks for your help.

  • I can not get the automatic updates on my samsung jack sgh-i616. _ "connection to the update server is not available. Check your data connection settings and make sure that the device date and time are correct "___RESULT CODE: 80072ee7__ _"

    I can't get the automatic updates on my samsung jack sgh-i616.

     

    "Connection to the update server is not available. "Check your data connection settings and make sure that the device date and time are correct.

     

    RESULT CODE: 80072ee7

     

    -It is a windows mobile 6.1

    Thank you very much! = D

    As a guide.

    This error code translates ERROR_INTERNET_CANNOT_CONNECT.

    You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
    http://support.Microsoft.com/kb/836941

    Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

  • Different sampling rate with the same connector AIO, Labview FPGA

    Hello

    I use LV 2009 with the new Toolbox FPGA and an NI PXI 7854R. I acquire an analog signal with a sampling frequency of 600kS / s. I need as the sampling rate for the processing of the data, but I also need the signal sampled with a much smaller, variable sampling frequency to a FFT.

    I've attached a picture to clarify, in a simple example, I'm looking for.

    I tried with the structure case only take each ' iht iteration, but did not get the expected results.

    Does anyone have another idea how to solve my problem? Of the, "Resampling" express VI in the funtion FPGA palette does not help me.

    Thanks in advance,

    Concerning

    Hello

    the connector for the analog input is a "shared resource", so you should he alone in your FPGA Code.

    Find attached an example that shows how to perform this task of analysis.

    Concerning

    Ulrich

    AE OR-CER

  • A "synch" iTunes always means that the device (iPhone) will be synchronized to the iMac?

    A "synch" iTunes always means that the files will be copied to or removed from the device (iPhone) to match what is currently on the computer to iTunes (iMac)?    And not the other way around?     In other words, if my iPhone has a photo that does not exist on the iMac, the photo will be deleted from the iPhone when the two are in sync?  Thank you!!

    A "synch" iTunes always means that the files will be copied to or removed from the device (iPhone) to match what is currently on the computer to iTunes (iMac)?

    Yes. See recover your iTunes from your iPod or an iOS device if necessary.

    TT2

  • You registering R7000 says that the device is already registered to another accountR7000, engineering, AC1900, Adva

    Hello

    I have a Netgear Nighthawk R7000 (AC1900) router with firmware 1.06.40. I tried to register for the first time the router with Netgear genius, so I can access it from the Cloud. I have created a genius account, validated email address. But when I try to add the router to the cloud I get a message error "this device is already registered by another account.

    How can I connect my router to my Netgear genius account?

    Thank you!

    Hi @linxeye182,.

    I made my own tests and was able to cancel the registration of the unit by resetting it. Please try to use the latest firmware available on the support site which is version 1.0.4.30 then reset and reconfigure the router. You can check out the link below to download.

    http://www.NETGEAR.com/support/product/r7000.aspx

    Once you have reset and reconfigured the device, you can go through the record. You can refer to the link below for the steps.

    http://KB.NETGEAR.com/app/answers/detail/A_ID/26109

    Please keep us posted on the results so that we can proceed accordingly if it does not work.

    Kind regards

    Dexter

    The community team

  • I found an ipod and kept for 2 days... I thought to use it, but it says there that the device is disabled... How can I use it?

    I need help to reset the unit so that I can use it... TQ

    Turn the iPod into the nearest police station, it it is not yours.

    If the iPod is disabled, this means that the owner has enabled iCloud locking.

    There is NO WAY to bypass the lock to iCloud.

    There is NO point to what iCloud lock if it could be bypassed.

    iCloud lock is a measure of protection against theft.

  • MyRIO_problem have to deploy every time that the device is not

    Hello
    I just want to ask u MyRIO.

    After that I deployed MyRIO program. I can run.
    Went however that I power off the power supply and that the former program cannot run. I have to deploy the program again.

    So, how to run the program without deploying the program. That mean that eating IT the MyRIO, the program runs continuously. (no need to redownload the program).

    Maybe you can help with that.
    TQ

    concerning
    Louis

    Hi Louis,.

    Try to build an executable application of the RT VI using the specification build and configure the application to run in real time to run at startup. Then the executable would automatically be stat up when myRIO boots.

  • How to display a different value than that of back-end for a quick dashboard data

    Hello Experts,

    We have a command prompt of dashboard for a report that has short values. I need display a full name for the prompt value instead of abbreviated values such as San Francisco SFO, in New York for NYC, etc. Here are the back-end OFS data values, etc. of NYC. Any ideas on how to achieve this?

    You can create a static table and use the column id descriptor in RPD.

    http://www.rittmanmead.com/2010/08/Oracle-BI-EE-11g-handling-double-columns-iddescription-interoperability/

  • ASA 5520: SSL VPN by using a different IP address that the ASA public IP address

    Hi guys,.

    I'm trying to configure an SSL VPN on a Cisco ASA5520.

    Unfortunately port 443 interface OUTSIDE of the SAA is already used by Microsoft Outlook Web Access and I can not change the configuration of Outlook. This configuration already in place allows me to use the public IP address of the ASA as IP Cisco VPN for the Web page.

    I don't not want to use a different port so to keep life easy for users.

    I have a few available public IPs that I can use so I wanted to use one of them instead of the OUTSIDE of the ASA interface. Any idea how I could do?

    Thank you

    Dario

    Unfortunately you can not use any other public ip address, except the ASA outside IP interface to complete the SSL VPN.

    The only options that you have is to change the Outlook to use another port or the SSL VPN to use a different port.

  • JTable to use a different TableUI than BasicTableUI the value

    I need to have a use JTable a different object to TableUI that I created. I know I put the user interface into the JTable constructor via table.setUI (uiComponent); but in this case the BasicTableUI is installed, uninstalled, and then my custom user interface is installed. I would avoid the BasicTableUI being installed in the first place and have the right use of JTable go my UI of the EEG. I extend possibly off the JTable to this component if I had to do something that would be an option. An idea I had that I wasn't able to get to work was the substitution of the following:
    private static final String _uiClassID = "CustomTableUI";
public String getUIClassID() { return _uiClassID;}
    and in so doing:
    UIManager.put("CustomTableUI", CustomTableUI.class);
    but this seems to just give me the following error message:
    UIDefaults.getUI() failed: no ComponentUI class for: gui.components.customtable.CustomTable[,0,0,0x0,invalid,alignmentX=0.0,alignmentY=0.0,border=,flags=251658248,maximumSize=,minimumSize=,preferredSize=,autoCreateColumnsFromModel=true,autoResizeMode=AUTO_RESIZE_SUBSEQUENT_COLUMNS,cellSelectionEnabled=false,editingColumn=-1,editingRow=-1,gridColor=,preferredViewportSize=java.awt.Dimension[width=450,height=400],rowHeight=16,rowMargin=1,rowSelectionAllowed=true,selectionBackground=,selectionForeground=,showHorizontalLines=true,showVerticalLines=true]
java.lang.Error
     at javax.swing.UIDefaults.getUIError(Unknown Source)
     at javax.swing.MultiUIDefaults.getUIError(Unknown Source)
     at javax.swing.UIDefaults.getUI(Unknown Source)
     at javax.swing.UIManager.getUI(Unknown Source)
     at javax.swing.JTable.updateUI(Unknown Source)
     at javax.swing.JTable.<init>(Unknown Source)
     at javax.swing.JTable.<init>(Unknown Source)
     at javax.swing.JTable.<init>(Unknown Source)
     at gui.components.customtable.CustomTable.<init>(CustomTable.java:37)
     at gui.components.customtable.CustomTable.main(CustomTable.java:94)
    Any help/thoughts would be apprecited!

    Thank you for your time,
    Brandon

    Officialhopsof wrote:
    and in so doing:

    UIManager.put("CustomTableUI", CustomTableUI.class);

    UIManager.put("CustomTableUI", "CustomTableUI.class");

    You will need the full qualified class name.

    How I investigate such things is by default to sysout and examine it.

    System.out.println(UIManager.get("TableUI"));
System.out.println(UIManager.get("TableUI").getClass());

    Impressions

    javax.swing.plaf.basic.BasicTableUI
class java.lang.String

    DB

Maybe you are looking for