Authentication RADIUS for VPDN

Similar Questions

• Try to set up authentication RADIUS on ASA5505 8.3

  I set up my firewall with local authentication for a regular dynamic VPN put in place, but I need to change it to authenticate with the server. The server is configured and ready to go, but I want to make sure that the firewall will also be.

  Here is my config:

  ASA # sh run
  : Saved
  :
  ASA Version 8.3 (1)

  ASA host name
  mydomain.local domain name
  activate the encrypted password of GmSL9emLLUC2J7jz
  2KFQnbNIdI.2KYOU encrypted passwd
  names of

  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0

  interface Vlan2
  nameif outside
  security-level 0
  PPPoE client vpdn group pppoe_group
  IP address pppoe setroute

  interface Ethernet0/0
  switchport access vlan 2

  interface Ethernet0/1

  interface Ethernet0/2

  interface Ethernet0/3

  interface Ethernet0/4

  interface Ethernet0/5

  interface Ethernet0/6

  interface Ethernet0/7

  boot system Disk0: / asa831 - k8.bin
  passive FTP mode

  clock timezone CST - 6
  clock to summer time recurring CDT

  DNS server-group DefaultDNS
  mydomain.local domain name

  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface

  network obj_any object
  subnet 0.0.0.0 0.0.0.0

  object obj-vpnPool network
  192.168.101.0 subnet 255.255.255.0

  the SERVER01 object network
  the host 192.168. *. *

  object obj-internal network - 192.168.1.0
  subnet 192.168.1.0 255.255.255.0

  network of the SERVER02 object
  the host 192.168. *. *

  network of the SERVER03 object
  the host 192.168. *. *

  object obj-OutsideIP network
  Home 74.164.148.6

  splittunnel list standard access allowed 192.168.1.0 255.255.255.0

  access extensive list ip 192.168.101.0 outside_in allow 255.255.255.0 192.168.1.0 255.255.255.0
  access extensive list ip 192.168.1.0 outside_in allow 255.255.255.0 192.168.101.0 255.255.255.0

  outside_in list extended access permit tcp any host 192.168. *. * eq www
  outside_in list extended access permit tcp any host 192.168. *. * eq https
  outside_in list extended access permit tcp any host 192.168. *. * eq smtp

  pager lines 24
  asdm of logging of information

  Within 1500 MTU
  Outside 1500 MTU

  IP local pool vpnpool 192.168.101.50 - 192.168.101.100

  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 524.bin
  don't allow no asdm history
  ARP timeout 14400

  NAT (inside, outside) source static obj-internal - 192.168.1.0 obj-internal - destination 192.168.1.0 static obj-vpnPool obj-vpnPool

  network obj_any object
  NAT dynamic interface (indoor, outdoor)

  the SERVER01 object network
  NAT (inside, outside) interface static tcp smtp smtp service

  network of the SERVER02 object
  NAT (inside, outside) interface static tcp www www service

  network of the SERVER03 object
  NAT (inside, outside) interface static tcp https https service

  Access-group outside_in in external interface

  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console

  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  http 0.0.0.0 0.0.0.0 inside

  No snmp server location
  No snmp Server contact

  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto dynamic-map-RA - VPN 1 set of transformation-ESP-3DES-MD5
  Crypto dynamic-map-RA - VPN 1 set of security association lifetime seconds 28800
  cryptographic kilobytes 4608000 life of the set - the association of security of VPN - RA 1 dynamic-map
  Crypto than VPN-RA - dynamic-map 1jeu reverse-road
  Crypto map 65535 ipsec-isakmp dynamic VPN - RA RA - VPN
  RA - VPN interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow inside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  ISAKMP crypto 10 nat-traversal
  crypto ISAKMP ipsec-over-tcp port 1000

  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet 0.0.0.0 0.0.0.0 outdoors
  Telnet timeout 60

  SSH 0.0.0.0 0.0.0.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 60

  Console timeout 0

  management-access inside

  VPDN group pppoe_group request dialout pppoe
  VPDN group pppoe_group localname [email protected] / * /
  VPDN group ppp authentication pap pppoe_group
  VPDN username [email protected] / * / password *.

  dhcpd dns 192.168. *. * 4.2.2.2
  dhcpd lease 8400
  dhcpd ping_timeout 750
  dhcpd mydomain.local domain
  dhcpd outside auto_config

  dhcpd address 192.168.1.2 - 192.168.1.33 inside
  dhcpd allow inside

  priority queue inside
  priority-queue outdoors

  a basic threat threat detection
  Statistics-list of access threat detection

  no statistical threat detection tcp-interception
  WebVPN

  internal examplevpn group policy
  attributes of the strategy of group examplevpn
  value of server DNS 192.168. *. * 4.2.2.2
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list splittunnel
  mydomain.local value by default-field

  vicky 9fO.vlLc77pAFoHp of encrypted privilege 15 password username
  username otherusers encrypted password privilege 10 hhckff6QokyoRdar
  examplevpn IKg0RMHfprF6Ya3u username encrypted password

  admin DwCTJcBn.Q0dDe9z encrypted privilege 15 password username
  attributes of user admin name
  VPN-group-policy examplevpn

  type tunnel-group RA - VPN remote access
  type tunnel-group examplevpn remote access
  tunnel-group examplevpn General-attributes
  address vpnpool pool
  authorization-server-group (outside LOCAL)
  Group Policy - by default-examplevpn

  examplevpn group of tunnel ipsec-attributes
  pre-shared key *.

  Global class-card class
  match default-inspection-traffic

  class-map class_sip_tcp
  sip port tcp eq game

  class-map inspection_default
  match default-inspection-traffic

  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512

  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect sqlnet
  inspect the tftp
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the icmp
  inspect the amp-ipsec
  Review the ip options
  class class_sip_tcp
  inspect the sip

  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:3edb25d4a550f0394e8c1936ab3326ad

  Did I all I have to add / is this correct?

  RADIUS protocol AAA-server RADIUSvpn
  Max - a attempts failed 5
  AAA-server vpn (DMZ) host 172.16.1.1
  interval before new attempt-1
  timeout 30
  key cisco123

  type tunnel-group RA - VPN remote access
  General-attributes of RA - VPN Tunnel-group
  address vpnpool pool
  authentication-server-group RADIUSvpn

  I'm still relatively new to firewalls and find the overwhelming online help sometimes. Help, please

  Vicky

  Can you comapre the config with the doc and see if something may be missing?

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808c3c45.shtml

  Use the troubleshooting area in the doc to find the DN, I think that you are missing a part of the DN string. Sorry for the late response

• Is RV320 - possible to use the RADIUS for the users of PPTP VPN?

  We replace a Draytek with a RV320 router and have trouble with the last step which is the VPN configuration. We currently have our VPN users defined in a RADIUS server, and the Draytek check credentials against this. However, the RV320 doesn't seem to work in the same way - the server RADIUS is configured but VPN users cannot connect. There is nothing in the system log to indicate if there is a problem connecting to the RADIUS server, or if the router is even able to use RADIUS for PPTP connections. Adding a user manually allows PPTP connection so I don't know the PPTP settings on the client are correct, and that the PPTP on the RV320 server is functional and configured correctly.

  RADIUS authentication should not work for users of PPTP then I could set them up manually, except that the web interface of RV320 has a restriction on the length of usernames - it seems to allow only 11 characters, where I would need to have user names up to about 15 characters for some of our remote users. Why the RV320 have such a length short maximum username?

  Dan

  Dan,

  I got the feedback from the engineering group. Even if she has the RADIUS as a drop-down option, the PPTP server only supports local user database authentication. I was wrong in my first answer. They confirmed THAT SSLVPN & Easy VPN will support RADIUS but not installing PPTP.

• Authentication Radius Cisco with Windows NAP with encrypted authentication

  I need authentication radius configuration for Cisco IOS devices for device management. My radius server is on Windows 2008 R2.

  Can I implement this with encrypted authentication? In the attached diagram, can what protocol I use for encrypted authentication?

  According to some sites, we need activate authentication in clear text. All those put in place secure as MSCHAP authentication?

  Hello

  You activate the text authentication (PAP) clear. Don't forget Ray sends the username in clear but encrypts the password. You can confirm this take a wireshark capture. You will also get the RADIUS encryption using a key to Ray long and complex.

  If you want to encrypt the user name and password, then you would use GANYMEDE

  Thank you

  John

• WLC with ACS 5.1 (RADIUS) for management * AND * Network users

  Hello

  I have authentication RADIUS of installation for the users of the network AND management on my NM - WLC (5.2 ongoing execution) against ACS 5.1

  My Question is:-

  For users to log in to Admin, I need to come back "Service-Type = Administrative - User" in order to make it work.

  Because the ACS sees all applications from the same device (WLC) for Admin and network users,

  the way I am currently treats it is by creating a filter based on the user name

  Thus, users that contain 'admin' in their ID, use a set of

  Network access policy authorization, who has an authorization associated with the attributes RADIUS profile.

  Normal users have a ' network access policy authorization different rule ", with a different profile.

  While this DOES WORK fine, still me I was wondering if there is a better way to do it, rather than create a rule

  based on the user name.

  I could use GANYMEDE + for the management, but I don't think that ACS allows the same client AAA (WLC) to use both protocols.

  Thank you

  I think it's something very common for things to do

  You may notice that ACS 5 comes preinstalled with a selection policy of service that differentiates them the Protocol-based queries and orders or service 'Access to the network by default' or "Default Device Admin" out of the box

  If you want only to RAY can either disable or delete the rule for applications of GANYMEDE + or not choose GANYMEDE + in the definitions of the unit

• Authentication Radius 4.2 ACS and RADIUS Accounting

  Is it possible to configure 4.2 ACS to authenticate users of a wireless network (with autonomous APs) through RADIUS while I use the same ACS to provide the command represent the points of access via GANYMEDE +? This issue came out because when I configure the APs 'AAA Clients' under 'Network Configuration' of the ACS server (necessary config for authentication APs and end users), the authentication method used is the RADIUS (Cisco Aironet) and it prevents the generation GANYMEDE server command accounting reports under "reports and activities > GANYMEDE + Administration.

  Any idea on how to solve this problem?

  Thank you

  Antonio

  Hello

  Need to add a different hostname for the AP... IE, RPOS and APt, where you can use the same IP n but use radius for Ganymede and the other.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• Setting up authentication Radius ACS 4.0.2

  Dear Experts,

  I have GBA 4.0.2 to my network, I want to use for 802. 1 x Radius for customers on the methodology of PEAP-MSCHAPv2 authentication.

  According to the documentation "" EAP authentication with RADIUS server ", Doc ID: 44844 "

  I have configured Network Configuration and populated by AAA client IP address range and the key secret.

  Question 1:

  Under option to authenticate using, there are various flavors available for the selection RANGE. For a Non AAA Cisco client, choose IETF RADIUS?

  

  Question 2:

  In the snapshot above, it has an option called Global authentication configuration, where we can configure EAP configuration. Under subsection PEAP, there is an option to 'allow EAP-MSCHAPv2' checkbox.

  After checking that a restart is required on the ACS server? It would cause disruptions to existing services on GBA?

  Kindly help that she is not mentioned in the documentation available with me.

  Kind regards

  Knockaert

  Hello

  Question 1:

  3 rd-Party devices should generally conform to the RADIUS standards. In this case select RADIUS (IETF) should be fine. If specific attributes of 3rd-party (for example the VLAN ID) are required and then contact support for 3rd - Party device to confirm if a RADIUS dictionary must be added to the RADIUS server in order to send vendor specific attributes.

  NOTE: We can add dictionaries of RADIUS for GBA in the case described above, but you will need to file the appropriate dictionary usually provided by 3rd - Party device support.

  Question 2:

  To enable PEAP or EAP 4.x GBA any other method, we need to use the option send + apply. ACS services will be restarted (RADIUS and Auth services). It should take less than a minute on a common scenario for the candidate countries to apply the changes. It is not a reboot of the server, but a restart of the services instead.

  I hope this helps.

  Kind regards.

• ISE device administration authentication Radius possible?

  Hello

  does anyone know if the edge RADIUS authentication and authorization administration is possible with the actual release of ISE? I know that GANYMEDE will be available in future releases.

  Concerning

  Joerg

  Yes it is possible according to the "Ask the experts" forum

  --------------------------

  https://supportforums.Cisco.com/thread/2172532

  "If you use RADIUS for the administration of the system, ISE can be used using authorization policy elements that return Cisco av-pairs."  But personally, I think that ACS is currently superior to ISE for this task. »

  --------------------------

  In any case, I'm about to test "device admin" and "network access" at the same time in the same switch with Radius and ISE.

  Please rate if this can help

• The use of certificates as the authentication method for AnyConnect VPN

  I'm trying to add certificates as authentication method for one of my AnyConnect connection profiles, that is, by using the option 'Corresponding certificate' available in the profile of the Client AnyConnect. My question concerns the "Distinguished Name Entry" options available. I know what some of them refer to the (for example, "TRANSMITTER-CN" is just like that), but some of them I don't know ("GENQ", "EA", etc.). Is there a reference somewhere that I can use to understand what each of these options to average? Here a sreenshot of the window in question. Thank you!

  Untitled.PNG

  

  The order has a good explanation of the various DN fields. Here is a copy of the inscription:

  Tag values are as follows:

  DNQ = qualifier DN
  Generational qualifier = GENQ
  I have original =
  GN = first name
  N = name
  SN = surname
  IP = IP address
  SER = sΘrie numΘro
  UNAME = unstructured name
  EA = address Email
  T = Title
  O = organization name
  L = local
  SP = State/Province
  C = country
  OU = organizational unit
  CN = common name

• How do I put 4 different RADIUS for the same element?

  I work with a rectangle and I need to set the radius of the top left corner at 100 and 10 other 3 corners.

  Hello

  Unfortunately, this is not possible. You can have two different RADIUS for corner, to the same rectangle. You can only activate/RADIUS for each corner. But if they are enabled, all the corner will have the same RADIUS.

• Get "authentication error" for a device that is not in the OME

  Hello

  I'm really stuck here. We have over 15,000 "authentication failure" for a device that is not listed in the section "devices." That's why I'm unable to remove this device. The alert is displayed with the ip address that points to a live device (Equallogic member).

  Here's what I've done so far:

  When I try to "ignore this device only" I get an error saying that there is no mechanism for this alert. When we look at the device ID in the database table is displayed as -1

  The goal is to have the reporting of Equallogic in OME and when I add the Group and the Member (which is using this ip address) the device adds ok. But the Alerts continue to occur (showing the correct DNS name this time).

  I then removed the discovery range devices but alerts keep coming (with ip address).

  So for me, it looks like this device got stuck somewhere in the OME and is accessible, although there is no device. But I don't see it came from. These alerts are just a pain and I need to find a way to get rid of it.

  Please is - can anyone enlighten us in this strange behavior. We are on OME 1.2.0.3441

  Thank you

  Thorsten

  Hi Thorsten,

  Well I can confuse or missing some subtle detail here.

  When it comes to SNMP alerts, OME don't communicate with the target, the target device sends an alert to OME.  So if OME Gets a rogue alert in the alert/event console, this is because the device is pointing to the OME IP for sending traps.

  You looked at the target device SNMP parameters itself?

  THX

  Rob

  (Sorry if I'm being dense and not your question)

• BAM connection with jdeveloper authentication failed for Basic realm

  Hi all
  
  
  I'm trying to connect to BAM 11 g, my authentication is correct, but when I try to test the connection I get the error authentication failed for Basic realm = "oracle-bam-webservices.
  
  any ideas on how to solve this problem?
  
  Thank you
  K

  Hello

  Please ask your question on the forum BAM. I guess that they are aware of the possible error messages in their product (at least better that we are)

  Frank

• Authentication failed for Basic realm = "oracle-bam-webservices" - BAM 11 g

  Hi all
  
  I BAM 11g, im trying to create a connection of BAM of Jdeveloper, but I get this error authentication failed for Basic realm = "oracle-bam-webservices.
  
  I tried boucing the server and rebooting my machine, but I still have the problem. All my authentications are correct. is there a way to get around this?
  
  Thank you
  K

  Hello
  BAM11g is certified with SOA 10.1.3.4 and beyond. Therefore, it is preferable to use JDev 10.1.3.4 and later versions.
  We don't certify with 10.1.3.3 SOA.
  The other thread is BAM connection
  Poyard

• How Anyconnect VPN users will connect with cisco ASA, which uses the server (domain controller) Radius for authentication

  Hi team

  Hope you do well. !!!

  currently I am doing a project which consists in CISCO ASA-5545-X, RADIUS (domain controller) server for authentication. Here, I need to configure Anyconnect VPN and host checker in cisco asa.

  1 users will connect: user advanced browser on SSL VPN pop past username and password.

  2. (cisco ASA) authentication: VPN sends credentials to the RADIUS server.

  3 RADIUS server: authentication: receipt and SSL VPN (ASA) group.

  4 connectivity creation: If employee: PC so NAW verified compliance, no PC check Assign user to the appropriate role and give IP.

  This is my requirement, so someone please guide me how to set up step by step.

  1. how to set up the Radius Server?

  2. how to configure CISCO ASA?

  Thanks in advance.

  Hey Chick,

  Please consult the following page of installation as well as ASA Radius server. The ASA end there is frankly nothing much difference by doing this.

  http://www.4salesbyself.com/1configuring-RADIUS-authentication-for-webvp...

  Hope this helps

  Knockaert

• ISE - authentication radius AAA for n access

  Hello

  I have configured the switches to use the ISE as a Radius Server to authenticate with, on the ISE, I configured an authentication strategy

  for the 'DNA' using the devices 'Wired' group that points to the source of identity AD to authenticate.

  All testing switches access connection we found 2 results:

  1.A domain user can connect to the switch as expected.

  2. each domain user that exists in the source of advertising identity can connect, this is an undesirable result.

  So I will try to find a way to restrict access to the ENAD to only a specific group belonging to the announcement, for example the group/OU

  of the IT_department only.

  I did not, would appreciate any ideas on how to achieve this.

  Switching configurations:

  =================

  AAA new-model

  !

  AAA authentication login default local radius group

  !

  ISE authentication policy

  ==================

  !

  Policy name: DNA authentication

  Condition: ": a device Type equal to: all Types of devices #Wired.

  Authorized Protocol: default network access

  Use the identity source: AD1

  !

  No problem is how to set up policies, don't forget to evaluate any useful comments when you are finished testing.

  Thank you

  Tarik admani