Authorization of 'change step list Configurations! -Still a bug?

Similar Questions

• Change the system configuration and yet no difference in config

  This question is about a router CISCO1941/K9, Version 15.0 (1r) M15.

  When I type

  reload in 4

  He asks me

  The system configuration has changed. Save? [Yes/No]:
  % Please answer 'yes' or «»

  even if

  See the config differences: running system of archives-config nvram:startup

  gives

  ! Contextual Diffs Config:
  ! No changes have been found

  and

  Show running

  gives

  Current configuration: 5031 bytes
  !
  ! No change since the last restart configuration

  My question is: How can I determine WHAT system configuration has been altered?

  As far as I know, the only thing changed is the Terminal length that I occasionally switches for use with the recording of session with PuTTY, which is

  Terminal length 0.

  This router has been in production for months and I don't want to break anything (obviously).  I need to make a change to the configuration of the access-list and wanted to protect me by saying to reload in 4, and then I was probably cancel about 1 minute.  But now I'm worried about it save yes/no question.

  Thank you.

  Hello

  Just save config running and configuration of boot in text files and compare them. Have you enabled all logging on the router?  It may be because of this.

  Just make sure that your configuration register is 0 x 2102. You can see by the show version command

• C4780 omitting step of configuration of wireless network

  Hi at all - no matter what I try, connect get the C4780 from the step network configuration.  All abstracts of the report status come back negative - "Cannot retrieve intellectual property."

  The wireless network is hosted by a DLINK DI-624 with WPA - PSK encryption. HOWEVER (!), I'm ONLY using the 624 as access point and not like the firewall/gateway to my ISP (verizon FIOS).  The real gateway is a DLINK DI-604 with an IP 192.168.0.1.  The DI-624 has a different IP address static (.15 in this case) without WAN connection.  The FIOS WAN is connected to the 604 and the 604 provides the DHCP service.  The DHCP service on the 624 (wireless) is off - it's just acting as a wireless access point.

  For the curious, the reason is that we only run the wireless when we need as the House is especially wired.

  This wireless setup works fine for all other devices that we tried (portable computers of all sorts.), the iPods of all kinds, games, etc.

  But not for this printer.  Question - is this printer assuming that the wireless access point _is_ the entry door?  Is there anything else I can try?  Thank you very much in advance!

  Amazing - I'm speechless.

  On the implication that the C4780 requires WPA2, I started looking into that.  It turns out that apparently verizon FIOS in the old days (for how long I don't know) used routers wireless DI-624 (revC), which is what I have.  I got their share.

  These routers _do_ WPA2 support out-of-the-box, but _not_ to verizon!  It seems that verizon charge their own copy of the firmware on the device before giving it to customers.  Their version of the firmware does not supports WPA2.  Also, their version does not support other options native dlink.

  In addition, the firmware upgrade process has apparently a security check where incompatible updates are rejected.

  Then, try to install the real dlink firmware to get the support of WPA2 by downloading just the dlink firmware does not work.  Instead, one must "jailbreak" the DI - 624 by doing a hard reset that removes everything.  This leaves the open unit to install any firmware (an implication being that if a bad firmware is loaded, one can brick the device).  So after a hard reset, I installed the firmware dlink real, re-configured as an AP with WPA2.

  And tada, it works!

  As a minor side note, everything works except to go to the page interface web printer via a device wired (it seems to me that to get the printer Web page needs a wireless device).  However, this is not a problem.  This works.

  Thanks a lot for the persistence and time to support this list.

  p.s. Here is a link to find out how to reset the DI-624 and load new firmware:

  http://www.dslreports.com/Forum/remark, 11672142? Hilite = di + 624 + firmware

• How I download/install adobe first cc on the D drive because I don't have enough on the C: drive? Ive gone to settings on creative cloud and location of the file changed already but it still does not work.

  How I download/install adobe first cc on the D drive because I don't have enough on the C: drive? Ive gone to settings on creative cloud and location of the file changed already but it still does not work.

  Hi brandong13,

  Here are the steps that you can follow.

  1 change the location of installation using Creative Cloud Desktop App, go to preference > creative cloud > Apps and change the installation location.

  2. delete the folder '%Temp%' and restart the process.

  NOTE: Application is downloaded to the default location, we can only customize the installation location using creative cloud app in this case.

• Editable interactive report. To change the list column dropdown type filter.

  Hi all, I thought I had posted this, but I can't find my post, so apologies if it turns up to twice more...

  XE SUMMIT 4.2 11.2

  Ive created an editable interactive report... Everything works very well, and I have several Text, LOV and selection list columns...

  However when I now click on a column header to filter, sort etc drop-down list is the same format as the column itself. So if for example, I have a text box, then the drop-down list is also text boxes, if the column is a column LOV, the filter drop-down list is a list of fields LOV. (Im assuming this is correct behavior, because it simply inherits the column parent..)   So, I would change the lists to a list of standard display so that they are in order and can be used...

  I think so? I know I have to do, which is either to substitute the function that generates the dropdown filter... or probably more simply, write a bit of JS/JQuery that modify data for drop-down lists.  Im still to learn, some help would be appreciated...

  I think so. (and please correct me if I'm talkiing... garbage)   I need to find each of the appearance of the DIV with the ID that corresponds to the drop-down list box, and then loop through each entry and change the structure...

  Currently the source for drop-down fields resembles the following (for a text field...). :

  < div id = "apexir_rollover_content" >

  < a href = "javascript:void (false); ">

  < input type = "text" value = "24489" maxlength = size "2000" = "6" name = 'f06' > < / input >

  < /a >

  < a href = "javascript:void (false); ">

  < input type = "text" value = "N1021" maxlength = "2000" size = "6" name = 'f06' > < / input >

  < /a >

  < / div >

  How could I 1) browse each occurrence of div id = "apexir_rollover_content" on my page, so I found out about each other, how would I go through the list and change the line above an input to a standard list item text...? Or is there a simpler way to do it?

  Kind regards

  Richard

  Hello

  Problem was on your process to GET the VALUES of LOV.

  You did not bind the variable values of cursor.

  I created another process for your page that manages LOV BUDGET_CAT

  Kind regards

  Jari

• How to change the list of bookmarks

  Where can I find instructions to change the list of bookmarks?

  You can change the bookmarks in the bookmarks (library) Manager.

  • Bookmarks > show all bookmarks
  • https://support.Mozilla.org/KB/how-do-i-use-bookmarks

  Just to be sure you understand how this works:

  • By clicking on the star in the toolbar navigation go to bookmark the page in the "Unsorted Bookmarks" folder and the star lights in blue to show that
  • Bookmarks > 'Bookmark this Page' (Ctrl + D) going to bookmark the page in the folder of bookmarks Menu (you will need to confirm that)
  • 'Bookmark this Page' is accessible via the context menu in the area through the bookmarks menu or navigation in the menu or Firefox menu button drop-down bar (Alt + B)
  • If the URL in the active tab is set bookmark and the star is highlighted blue and then click the star highlighted or use "Bookmark This Page/Edit this bookmark" (Ctrl + D) to change the properties of the bookmark as the name and the location and move the bookmark to another folder or delete the bookmark

• Spam: how to change the list of junk e-mail in iPad

  How to change the list of junk e-mail in iPad

  If your question is about - how to indicate whether or not an e-mail is sent to the junk e-mail folder-

  Your best bet would be to do it on the web portal of the email provider (e.g. for Yahoo it would mail.yahoo.com)

  There is usually a button or switch to designate mail "Junk" or "not junk".

  If your question is rather modify the list itself

  Mailbox - junk e-mail - Edit button is at the top right

• ThinkPad Tablet 2 BIOS: I can't change the list of boot devices. Help, please!

  Hello community,

  I need to restore Windows on my ThinkPad Tablet 2 via USB. But I can't change the list of boot devices in BIOS. The F12 option is not available. It is said: "F12 key is used to call a pop-up the boot devices list. This option is available only when supervisor enters setup. »

  What can I do?

  Kind regards

  The problem is solved!

• How do I know if my router has been compromised if a hacker does not any change in the configuration of the router?

  How do I know if my router has been compromised if a hacker does not any change in the configuration of the router?

  Do you know how to access the Linksys configuration screen?  Click Administration.  You should be able to access the logs from here.

  What happens if they have an older linksys router?

  

  Click on the Windows "Start" button and select "All programs." Click on "Internet Explorer" to open a web browser.

  Type "192.168.1.1" in the address text box and press "enter." This IP address is the default value for a Linksys router. If you have reprogrammed the router to have a different IP address, enter your IP address instead.

  Click the log tab

  model # here

  http://homesupport.Cisco.com/en-us/support?ICID=global-header-support-link

  192.168.1.1 is an IP address that is normally used by the routers broadbandfrom Linksys.

  If the router has an IP 192.168.1.1, you can connect by opening a Web browser and visiting

  http://192.168.1.1/

  This allows to connect you to the console of the router administrator and access its configuration screens.

  http://compnetworking.about.com/od/routers/g/192_168_1_1_def.htm

• How can I change the list of actions that appear when you right-click on a file?

  When you place your cursor over a file, then right click, you get a pop-up window with a list of actions that you can do in the file. Depending on the type of file, you get a different list of actions. How can I change this list. Or add or subtract from the it. Where Windows keeps related lists?

  In Windows Explorer, remove it all also missing button?
  Try to restore the files ZIP file association.

  For Windows Vista file association problems
  http://www.Winhelponline.com/articles/105/1/file-association-fixes-for-Windows-Vista.html

  Make a right click on the zip link, save target under... Right click on the REG file and choose merge. Note that you must be an administrator to apply these fixes.

• Cannot change the list of participants

  I'm trying to change the list of participants, but I get a message saying that the "system is unable to process' .  Any ideas?

  Thanks for responding. My role was that of the host. In any case, I'm finally able to change the list of participants. I was told that Adobe Acrobat Connect Pro is 'down' for a day or two, and it's probably why I couldn't change the list. It seems to be okay now.

  Thank you

  Suzanne

• How to make changes to existing configurations without quisceing

  Hi gurus B2B.
  
  How to make changes to existing configurations without quisceing and deployment of retirement?
  
  Its a production server, my project went live, a few weeks before. After two weeks my ISP asked me to change the delimiter setting of * to,.
  I then to the deployment, Quisced tab, retired, purge the existing configurations, and then I did the changes, approved the agreement and TP and recreated the (config) deployment even once, it happened successfully, but WE are unable to see the old transactions.
  
  Could someone help me how to make any changes without purging,
  
  If we simply pull out, wiothout purge, it shows error that name already exists.
  
  Concerning
  Suni

  Hi Suni,

  In B2B of Oracle 10g, it is mandatory. You must transfer the configuration (after quisceing and retirement) each time you make any change in the configuration.

  but WE are unable to see the old transactions.

  Once an old configuration gets served, messages related to it would not be included in the report, but they must exist in the DB tables. You can take an export (from the console) to the existing messages each time before you purge the old configuration to keep a backup copy of copy paper.

  If we simply pull out, wiothout purge, it shows error that name already exists.

  Two configurations with the same name cannot co-exist, and whence this error.

  Kind regards
  Anuj

• Rom1.2.1 calendar still has Bug - "this event don't exist anymore." (only for repeat well events)

  Upgrading to 1.2.1 solved many problems on my pre, including one-way sync with Google Calendar.

  But there is still a bug.

   

  Whenever I hit a recurring weekly or monthly event on the Meadow, a message bounces upward "this event no longer exists."

  Everything else is fine. For example, I can add new weekly/monthly events on Google or pre and they sync very well. Also, I can edit events at Google at will. Events not repeated works very well in all aspects, etc.

  Ok. I think I identified earlier bug, after many tests of course...

  Repeated events to meet with this bug ONLY when they are repeated forever, in a Word, if you set "until what MM DD YYYY", it will be ok.

  I had changed all the events repeated on my calendars, set repeat until 1 January 2015. Then, after a sync, all are accessible on the meadow.

  It is not correct to say that the only daily/weekly/monthly events have problems. Now, it may not be clear that the only problem is webOS does not handle the Google Calendar calendar for always repeated events.

  Hope this is useful and you guys at Palm can try and solve (this is still a bug, is it?) in the next update soon. Thank you very much.

• Photoshop CC2015.0.1 still have bug profile convert?

  Photoshop CC2015.0.1 still have bug profile convert?

  The PSD(must use my PSD) and the video.

  If in preferences > performance > the GPU settings > advanced settings > Drawing Mode = base

  

  The conversion is OK, but if it is Normal or high, the result is false.

  Windows 10 - CC2015.0.1 x 64 - AMD R9 280 x pilot Crimson edition 15.11.1

  Well, I constantly kept GPU to Basic for years, precisely because the normal/advanced is not always reliable. And I've known that for a long time. It is, however, that the view which is at issue, not the file itself.

  Unless you have found something else. Could you elaborate a little bit?

• How to change step.result.status

  Hello

  I know just how I can configure the result step to something else state that "passed" or "failed". I know that I've done it before, but now I can't get this to work.

  Simple sequence attached file to demonstrate what I'm trying. Report as text in my machine looks like this:

  Start the sequence: MainSequence
  (Text of C:\Temp\status change test.seq)

  Pass/fail test: skipped
  Pass/fail test: failed
  TEST
  Test digital limit: failure
  Measurement: 0
  Limits:
  Low:                   9
  High: 11
  Comparison type: FROZEN (> =)<>

  Complete the sequence: MainSequence

  No reference to what we are missing?

  BR

  Petri

  Petri,

  http://zone.NI.com/reference/en-XX/help/370052K-01/tsfundamentals/infotopics/step_execution/ contains a list of action a step performs when it is executed.

  As you can see, State Expression is evaluated after the Expression. Therefore, you can not use after Expression to set the Step.Result.Status property.

  The following two options, you can try to change the status of the step:

  Option 1:

  Create the custom step type and modify state Expression.

  Option 2:

  You can use the reminder of step motor after updating the result of step

  Option 3:

  Stage results will be added to the Locals.ResultList table. Therefore, after a stage performance, you can change the result container in the table if necessary.

  -Shashidhar