Automatically by turning and the wifi network?

Similar Questions

• Pavilion dv7 6c70el: drivers PCI and the Wifi network?

  Hello
  I recently formatted my laptop and when I reinstalled I noticed that I miss 2 pilots:

  -Wifi pilot
  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C & REV_01
  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C
  PCI\VEN_10EC & DEV_8176 & CC_028000
  PCI\VEN_10EC & DEV_8176 & CC_0280

  -Pci (maybe?)

  USB\VID_138A & PID_0018 & REV_0078
  USB\VID_138A & PID_0018

  Can someone help me?

  Hello:

  You need these drivers...

  WiFi:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5060882&swItemId=ob_105197_1&swEnvOid=4058

  Fingerprint sensor...

  This package contains the driver that allows the validity fingerprint sensor in the notebook models that are running a supported operating system. The fingerprint sensor analyzes fingerprints for use with biometric security applications.

  File name: sp56169.exe

• OfficeJet 6600 connects to the wifi network

  Hello

  I bought an Officejet 6600 and effortlessly connected to my wifi network, print and scan for a day. And there are two days that he stopped conntecting to the wifi network. In the meantime, our router turned off and turned back on. That's the only difference.

  First of all, the printer would not even detect the wifi network. I solved that by changing the configuration of the router (Cisco 3925 EPC) and passed under the Setup wireless "Wi - Fi protected setup" to "manual". I can now see the network on the printer again.

  But after that I've selected my wifi network and enter the WPA password, the printer tells me that the network connection is impossible. I printed a page of diagnosis, which told me that the problem is perhaps related to the MAC filter. But I have no MAC filters. I also tried to pass of WPA/WPA2 to WPA only, but that doesn't change anything.

  I also tried to set the mode wireless via the USB cable, but no avail. Everything seems to work, until the moment when he tries to connect to the wifi (screen with 'configuration' with the large antenna and pulses of radio waves).

  Should I give up and bring it to the store? I'm getting desperate!

  Thanks for your help in advance,

  Raphaël

  OK, to make sure I understand - the printer connects effectively to your wireless network, and well it works for a while once the printer goes to sleep, your computer or router may not wake.

  If this is the case there are a few things that we can try:

  1. in the settings of your router, make sure that the multicast is enabled.

  2. set the 2.4 GHz router to 11 channels.  I know it sounds weird, but please try.

  3. set an IP address of the printer:
  
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  
  Now, stop the router and printer, start the router, wait, and then start printing.

• Optimal, set up for the airport and the power network line?

  Hoping to any network gurus can advise on the optimal configuration for my network.  Current configuration is as follows.  1 Zyxel DSL modem configured to act as the router, PPPoE (not the bridge mode) mode, which is the default value.  2. Airport Time Capsule (ATC) connected to the modem via an ethernet cable plugged into the WAN ATC port.  ATC configured in Bridge mode.  Adapter network line connected to the LAN of the ATC port.  2nd line network adapter is connected to the opposite end of the House where the Time Capsule wireless signal is weak to non-existent.  Airport Express (AE) plugged into 2nd network adapter line.  I have a lot of devices (computers, printers, cell phones, DVR, etc.) which must connect wirelessly to the network.  Here are my questions:

  1. is it better to act as the router, rather than on the bridge, as I have to reconfigure the modem in Bridge mode and the most convenient way to connect using PPPoE Airport Airport?  Or is it not important?

  2. my hope is that by using the network adapters and the AE in the part of my house with the worst WiFi signal, I can push the range of my network and all devices to give a good signal.  My hope is that the devices will be connected to any signal is stronger.  At present, ATC and EI do not have the same network name (or password).  It is better for them to broadcast 2 differently named networks, or both would be they networks of broadcast with the same name and password.  Or is it not important?  Is how important it that the ATC is able 802.11ac, EI is just 802.11n?  For reasons not clear to me, even though I have several 802.11ac devices (MacBook Pro and Nexus5x), they are on the 2.4 ghz band (I even if ca is the 5 ghz).  Don't know if something is set up wrong on my ATC.

  All the equipment is running the latest version of the software (OS X, iOS, Android, etc.).

  Thanks for any advice.

  1. is it better to act as the router, rather than on the bridge, as I have to reconfigure the modem in Bridge mode and the most convenient way to connect using PPPoE Airport Airport?  Or is it not important?

  Doesn't matter, unless there is a special feature like the network option of comments on the airport... that would require that the airport be configured as router.  Airports are not known for their reliability, PPPoE, so it is best to have the modem or modem/router to provide the credentials of the PPPoE connection.

  2. my hope is that by using the network adapters and the AE in the part of my house with the worst WiFi signal, I can push the range of my network and all devices to give a good signal.  My hope is that the devices will be connected to any signal is stronger.

  If the two access points use the same wireless network name and password, Mac will do a nice job of automatically move from one access point to another to pick up the best quality signal as they move home... but iPhones, iPads, and most of the PC will not.  If you name the two networks as well, so you will need to get used to temporarily disable WiFi on iPhone, iPad, etc. When you move from one region to the other. Then, when the device is in the new location, turn on the WiFi and the device usually pick the strongest signal from the nearest access point.

  If you use names of separate network for access points, you need to manually switch networks on each device whenever the camera moves from one region to the other.

  Is how important it that the ATC is able 802.11ac, EI is just 802.11n?

  Well, you know that the Express is not "ac" capable, so any device "ac" close the Express will connect at low speed "n".  You will probably not notice a difference in respect if your Internet speed is less the Express features.  If you copy large files from one computer to another or backup on the network, then a device that connects to the Express is going to be slower than a device capable of "ac" that connects to the ATC.

  For reasons not clear to me, even though I have several 802.11ac devices (MacBook Pro and Nexus5x), they are on the 2.4 ghz band (I even if ca is the 5 ghz)

  Everything in the wireless is a compromise. In other words, to get something, you must give up another.  "ca" is used to that in the band 5 GHz, so if your devices are connect 2.4 GHz, they connect to a slower 2.4 GHz signal.

  Here is the compromise...

  5 GHz signals have capacities of speed much higher than the 2.4 GHz signals... BUT... 5 GHz signals are significantly weaker than the 2.4 GHz signals. So you're really not going to get the benefit of 5 GHz, if your device "ac" is in the same room or it has line-of-sight with the router "ac".

  If a device of "ac" is a room or two away from the router "ac"... the device will probably connect 2.4 GHz... because these signals are more powerful penetration of walls and other obstacles a lot better than 5 GHz can never hope.  It is also possible that the 2.4 GHz signal several rooms away the router will also be the fastest signal at this location, because the signal slows down more it moves the router.  5 GHz quickly signals really slow down.

• Satellite U920T - need help to turn on the WiFi

  Hello!

  I have a laptop Toshiba Satellite U920T.
  My OS is Windows 8.1 x 64 with all updates.
  There is a challenge with wireless which started after I put in place a flight on charm bar Mode and back fired.

  When I disabled the flight Mode, the switch wireless of charm bar is remained handicapped as shown on the screenshot (sorry, all the screenshots are in Russian, but if something is not clear I'm ready to explain)
  http://bit.LY/12HGayL
  The adapter in Device Manager is Normal
  http://bit.LY/1Gd2ygA
  It is the latest version of the driver installed
  http://bit.LY/1Itn4NO
  The Windows Network Diagnostics Wizard detects that the wireless is turned off.
  http://bit.LY/1w84plz
  When I try to enable wireless using the utility of the farm, he pointed out that I should turn the WiFi hardware button
  http://bit.LY/1ItncNd
  But my laptop is not any material for the WiFi button. Only hokey, but it comes to establish a flight Mode.

  Need your help.

  Sincerely,
  Vadim

  Guess, what, I think that there is a problem between the driver and the system and consequently the system reports that the WiFi network is DISABLED.

  I recommend you to uninstall the Intel Wlan Device Manager driver.
  Then, you must restart the laptop.
  Please perform a complete shutdown (no hybrid closed, standby, etc.)

  After the new reboot, install the Wlan driver and reboot once more.
  It would be really interesting to know if you can activate the WLan after this short driver installation procedure.

• Satellite R840 - 12 c: cannot manually turn off the WiFi function

  I recently bought a brand new Toshiba Satellite R840 - 12 c Notebook.
  The Wifi light is still "on" and the function key does not work, in other words cannot manually turn off the WiFi feature.

  Although the WiFi feature is still "on" I can't connect to wireless modem. "

  When I go to Device Manager I find conflicts in "other devices" for

  1. network controller
  2 PCI Simple Communications Controller
  3 unknown Device

  Tried updating drivers connecting via ethernet cable to the modem, but nothing helped.

  Can anyone help?

  Hello

  Have you installed the driver WLan?
  The laptop seems to be equipped with the Atheros AR9285 WiFi card and in most cases the Fn + F8 key does not work because the Wlan driver is not installed or is not working properly.

  Recommend first of all remove the network card wireless from Device Manager, then restart the laptop. After restarting again install the new driver Atheros Wlan downloaded for this wlan card.

  Here you can find all the drivers Wlan published by Toshiba:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

• Can't connect to WIFI on all locations where the WIFI network is available

  Sometimes my computer will connect and detect the networks without wire, Hotels, airports etc. but do not work in the home and in some offices.

  I run put WXP updated with SP2 have an Artheros5005gs adapter. Any ideas?

  Hello

  It is a matter of compatibility between the WLan router and wireless network card.
  If the wireless network adapter does not support the same Wlan standards then you will not be able to establish the WiFi connection.
  Especially the hotspots (Wlan on airports, city, etc.) are not secure and that is why the laptop automatically connects to these wireless LANs.

  The WiFi network at home or in the office is secure for most and you need a right encryption key to connect to these wireless LANs.

  So I think you should check you settings router WLan configuration and usage of encryption right key, SSID, etc.

• I can't turn on the Wifi, Satellite L40 - 18Z

  Hello

  I use Satellite L40 - 18Z but I can not turn on Wifi.

  I am very sure that peripheral lla is installed another property and I tried a few ways to turn on the Wifi device but never turned on. Of course, never caught the signal. Rooter has no problem either.

  Manager says Deveice peripheral island works another property. And the driver is correctly installed. But I can't turn on parameter of network or windows Mobility Center.

  It's very embarrassing to write something like that, but I need your help.

  PS This is the first time that I post on this thread, but who answers? Toshiba support team?

  Thank you

  Hello
  You said, did you check if the device is properly installed in Device Manager. Is there a red X on the wlan module in the list? And he must have this name: RTL8187B.

  There are several ways to enable the wlan on your laptop. One, is the hardware switch of your laptop, the other thing you can try is a combination of FN to FN + F8.
  You can control if the WiFi is working when you see the symbol of the LED is on or not.

  Finally, it is a forum for user to user here.

• G5E22EA #A2N: unable to connect to the wifi network

  When I turn on the wifi in my HP Pavilion 15 laptop pc and try to connect to my network of your choice... it says "check and connection. After a minute, it says "cannot connect to this network '...

  I tried to use the other pc and smartphones to connect to my network of your choice via wifi and they connect successfully and I can use wireless net in other devices!

  Hello @Khaled-819.

  Thank you for your query,

  I understand that you are unable to connect to your wireless network, but other devices connect correctly.

  Have you ran the Windows troubleshooting tool?

  Did you run the Internet functionality and security in HP Support Assistant ?

  Here is a link to HP PC - troubleshooting wireless network and Internet (Windows 8) that should help you.

  If you are unable to connect I would test for a hardware failure.  You will locate network under the title of part.

  HP Notebook PC - detection of hardware failures (Windows, 10, 8)

  To say thanks for the reply please click the thumb up below.

  If you were now able to solve your problem please click on accepted the solution to help others.

• HP Photosmart 8000 A809 printer offline connects to the Wifi network

  My printer would sometimes disconnect from wifi, but by turning and the new, would solve the problem.  Now, I can not connect via wifi at all.  Diagnosis plug said: I'm very good signal strength with odds of PASSAGE on everything, no other corresponding network mine.

  Config with the correct network name and an IP address of 10.10.10.125.  I tried the USB connection and then converting to wireless, but establishing assistant gets as much as setting her up and recognizing the device, then I get this msg:

  NON-CONTACTED DEVICE

  The network configuration has been correctly transferred to the device. However, to continue to configure the network device, your Mac must have access to the device. So please make sure that your Mac has access to the network: "JC XXXX" and try again.

  Yet, the report says that I'M connected.  When I try to print something the msg happens "printer is off-line" still the blue light is on, and as I said, all diagnostics PASS.

  I turned everything works, including unplugging the router several times, restart my mac etc.  I'm not missing any software updated.

  I tried the suggestion of hp to put my IP address in my browser to access the Networking tab, but Google Chrome tells me that it can't find the address.

  I also reset the printing system.

  What else can I try to fix this?  Grateful for your suggestions!  Thank you!!!

  Looks like you have problems multiple) a printer goes offline and then b) you can not access the IP address of the printer and c) you get an error saying 'Inaccessible device.'

  What is the Mac version that you use to configure the printer? You're on a VPN or proxy?  Is the printer on the same network as the computer?  You have blinking lights on the printer?

  Here is a very comprehensive document that covers everything you need to do to get the configuration of the printer.  I recommend restoring the printer by default and then try to connect again.  Page 76 of the User Guide talks about what to do if you are unable to access the built-in web server

• L440 kills the wifi network

  Hello

  A few days ago, I bought Lenovo L440.

  I have problem with Wi - Fi. WiFi works perfectly with other devices: phones, tablets, laptops. When I connect to wifi with L440, wifi works from 5 to 30 min. and then crash. L440 kills the wifi network. All devices cannot connect to wifi up until I have to reboot the router.

  I've read about this problem, but I can't find in the Manager of tasks "discovery.exe" or LenovoEMC Storage connector Contral Panel.

  p.s. Win8

  Post what you did to solve the problem. There are a lot of users having problems with wifi to l440.

• Unable to connect to the WIFI network.

  Original title: Need computer help laptop to connect to the WiFi at home

  I have FIOS at home, but my new laptop is impossible to connect to the WIFI in my house, the diagnostic computer wasn't able to fix the problem, what can I do?

  Hello

  1. what exactly happens when you try to connect to the WIFI network?
  2. do you receive any error messages?

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:
  If the problem persists, you try the procedure described in the article and check out them.
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702

  Alternatively, you can check the link for more information:

  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless
  http://support.Microsoft.com/kb/871122

  Method 3:

  If the problem persists, you can temporarily disable the antivirus software and check.

  (a) click Startand then click run.

  (b) copy and Paste the following text in the box run command and then press enter:

  wscui.cpl

  (c) in the Windows Security window, click Virus Protection.

  (d) if the software is activated, display information about the antivirus program and note the name of the application.

  (e) click Start, click programs principally made and then look for and run the anti-virus program.

  (f) temporarily disable the software.

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this information helps!

• ProBook 6455 b: Probook 6455 b accidentally turned off the wifi connection

  I bought a hp probook 6455 b windows 7 yesterday and had everything set up, while he was playing with it, it turned off the wifi and now we can't put it back on, the light is orange and when I press nothing happens, any ideas

  Hello @thebutton

  Thanks for posting on the HP Forums.

  To get your question more exposure I suggest you post in the trade forums since the Probook 6455 b is a commercial product. You can do so here: laptop - HP ProBook, EliteBook, Compaq, slate/Tablet PC, Armada, LTE

  Support of your product page can be useful in the meantime: HP ProBook 6455 Notebook PC b

  I hope this helps!

• MDS is the WiFi networking

  My job application on mode MDS and BIS (IE push and pull)

  Now I have WiFi network...

  is MDS (push) WiFi networking

  Yes. The BlackBerry is trying to keep a tunnel to the BES/MDS via the WiFi network, the network provided allows such a tunnel (whether to the RIM network infrastructure or directly to the router BES/MDS).

• restrict the physical size of the wifi network

  Hello

  I intend to cover the building 80x80m by the amount of 1131AG APs and WLC4402 controller. But the strong demand of the customer is to physically restrain the posibilities of the long distance wifi connections (100 m and more building).

  Is there a function in wifi Cisco to drop connections incoming in case if the customer is 100 + m AP? (I mean that the power of the customer is high enough for this)

  What are the regular methods of resricting the physical size of the wifi networks?

  Thank you.

  Someone could be more than 100 meters away using a parabolic grid antenna, and the signal strength is perhaps not different from your regular users.

  You can try using the location device, but I think that even this might go a little goofy, if someone tries to spoof a MAC address.