Avaya PG
Hi all
I mean, we need to know if it is supported to connect an Avaya PIM using 2 boards MAPD for failover, each pim is connected (MAPD1) host1 and host2 (MAPD2). What failover in this scenario with PGs in duplex?
Thanks in advance.
You can do anyway, but the more traditional concept of deployment makes card/D #1 and PG PG a-side b-side to map/D #2. If you had two card/Ds in the scales and PGs b-side: the PG will require connection to the two all the time
It has no impact on ICM failover in traditional design as a failure of the card/D could lead to the other side of PG try to connect to the another card/D.
/ Jeff
Tags: Cisco Support
Similar Questions
-
I'm trying to download Avaya Communicator for iPhone, and every time I get in the App Store, I get no results found. In fact, just search the general term of Avaya shows no results.
Apple did shoot the Avaya apps out of the store? I just had a user to download and install it yesterday without any problem.
Thanks to Dom wrote:
Don't try to download Avaya Communicator for iPhone, and every time I get in the App Store, I get no results found. In fact, just looking for a general term of Avaya shows no results.
Apple did shoot the Avaya apps out of the store? I just had a user to download and install it yesterday without any problem.
Contact Avaya and ask them. It's their decision on what areas of app store so that their app available in.
-
Card PCMCIA Avaya on a machine Satellite Pro 4320 - 31 to load the driver error code
The machine works perfectly in all respects. Recently attempted to add an Avaya Silver wireless card to the system.
Somehow the system has problems with the supplied driver. I have redownloaded the driver support site (now on version 7.62, the driver should support the card as a "Avaya Wireless PC Card".) I have to the latest driver available.
Given that the machine works under Windows 2000, SP4 and all available patches, and yet didn't have questions about installing a card like this on a Windows 2000 computer before, I'm a little confused as to what may cause the problem.
The card is detected properly, and the pilot is recognized. When installed the Device Manager still representing a yellow exclamation mark on the map of Avaya. When investigating this error shows that Windows 2000 cannot load the drivers on an error code 31.
I found Code 31 made reference to possible support material that gives the questions. I turned my attention to the CardBus controller (ToPIC100 according to Device Manager). The version used is Microsoft, 20/06/2003, 5.00.2195.6717.
Appearantly it is a newer driver (5.1.2600.0) but I failed to bring one downloaded. Seems that it is only available through Windows Update, which does not show the update as being available for the machine.
Then... Anyone know how to get the map Avaya Wireless Silver active PCMCIA on a Satellite Pro 4320? I need a newer driver, or can not be done at all?
[Edited by: admin on 26 June 05 20:19]
Hello
Can you please check this 2 & temp 108020 = .bucketID & PAGE = Document http://support.avaya.com/japple/css/japple?temp.documentID=127473&temp.productID=10763. Maybe it helps you too.
Good bye
-
Problems with FVS336GV2 and AVAYA 9620L VPN
Hello
I have Avaya 9620 L is currently working and all the settings successfully with netgear FVS336gv3. My problem is, when the phone is turned off at the remote site in the afternoon and return the morning that he fails to connect via VPN. Just told IKE Phase 1 error. In my VPN log it says "cannot find the file configuration xx.xx.xx.xx. Now this configuration worked the previous day.
When I go to the netgear and change "encryption algorithm" or 'Authentication algorithm' (no matter what) that the newspaper says that it does not. I have change it back to what it was before and how you know he is running like a charm. In the course of the day, no matter how many times the phone or the netgear feeding cycle, it always connects. Only when he is off all nite, the next day, the netgear let the phone not connect unless I have change a setting and than back to his original one. If I change a setting on the Avaya netgear and it works.
Does anyone have any ideas as to why the netgear blocks VPN until I have change the setting?
Hi Moussa,.
The firmware 3.1.1 - 08 seems to be more stable than version 4.3.3 - 6 at least for my setup here. Last week I had no problems and it works every morning when powered. For now I'll stick to firmware V3.1.1-08.
-
Turning on my laptop and can't do anything says not avaiable netwoks
I turned on my laptop and it opened to a page windows not my usual login page and it showed a box with cord where my wifi allows you to be, I pluged in the power cord and it shows still no networks avaiable... help me solve this please
I turned on my laptop and it opened to a page windows not my usual login page and it showed a box with cord where my wifi allows you to be, I pluged in the power cord and it shows still no networks avaiable... help me solve this please
Hello! You can check your internet connection. Make sure that your internet hub is turned on and all cables are securely fixed to the hub of the internet.
-
Spelling in Windows Mail: "langauge is no longer avaiable.
Original title: spell check new messages
In windows mail when I whant to use out check when I whant to send a new e-mail, he said that language is no longer avaiable
Your Caps Lock key is stuck.
This language is no longer available for spell checking
http://www.Vistax64.com/tutorials/68395-Windows-Mail-spell-check.htmlBruce Hagen
MS - MVP October 1, 2004 ~ September 30, 2010
Imperial Beach, CA -
TMS and AVAYA scopia endpoint interoperability
Hello
I have the management console of the TMS version 13.2. It is not the latest version, but I wonder if AVAYA SCOPIA XT-4300 products are compatible for integration in the TMS. It's like the product POLYCOM HDX?
Y at - it a document on which products are supported?
Thank you very much!
For TMS 13.2, you can take a look at the Documentation of integrated systems, specifically Product Support and documents using the feature to see what Cisco and 3 third-party products are supported.
Note, for the most recent releases TMS, you will need to look at the admin guides as well as Telepresence interoperability of data because there are no available detailed compatibility document, similar to those mentioned above, for the version beyond TMS 13.2.
-
Compatibility phone Avaya with Cisco Unified Communications Platform
Hello
We are currently a user all-Cisco on the side of routing, switching and network security, however, we are a user all Avaya on the phone, IP phone and voice communications. I laugh with all the problems we had with Avaya and would migrate to Cisco. My department head wants to know is it possible to have a Cisco platform manage all unified communications and voice mail on the back end, but continue to use the Avaya phones currently in place in each office, until we can replace in the coming years through attrition? It is essentially a measure of cost that is the main factor in management are unwilling to make any changes whatsoever because of investment is already in the existing system.
None of the Avaya endpoints are officially supported on Cisco CUCM, but if they SIP phones, they can be defined as 3rd-party SIP endpoints. That being said you get far more features and satisfaction with phones Cisco CUCM, otherwise ask for another set of questions, and at that time there a seller will point to the other.
-
Integration of ICM with Avaya with AES and CMS
My client is using Cisco ICM 7 (0) SR3 which is integtrated to an ACD Avaya help EAS and CMS. It's Live for a year, recently they tried to reach officer reason codes is not ready but MHI receives only zeroes instead of the reason code. I was wondering if anyone has experienced this or if there is a setting on the PG or the Avaya which could be changed so that CIM at the front desk officer is not ready codes.
Hi Klarash,
Thank you for closing the loop. Please check the question as answered in futures and other persons referred to them.
Thank you
/ Cedric
-
SF300 - 24 p with Avaya phones
Hello everyone,
I'm having a SF300 Switch - Cisco Small Business 24 p and I'm trying to connect it to an avaya phones and it gives me the headache of a lifetime for 3 days now. I tried all kinds of switchports and settings Vlan voice and LLDPs and all. I think I still messed with him vlan data after that was working fine and I have probably a configurations odd now would someone please help me with it.
Thank you very much
Here are the configs:-
User name: cisco
Password: *.
switch0a1172 #.
switch0a1172 #.
switch0a1172 #.
switch0a1172 #.
switch0a1172 #sho run
config-file-header
switch0a1172
v1.2.9.44 / R750_NIK_1_2_584_002
CLI v1.0
SSD of encrypted file indicator
@
SSD-control-start
config of SSD
control of password file unrestricted SSD
no control of the integrity of the file ssd
SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
!
database of VLAN
VLAN 9,13,20
output
ID of the vlan 20 voices
State of vlan automatic voice activated
Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
Add a voice vlan Yes-table 00036 b Cisco_phone___
Add a voice vlan Yes-table 00096e Avaya___
Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_
Add a voice vlan Yes-table 00d01e Pingtel_phone___
VLAN voice Yes-table add Polycom/Veritel_pho 00e075
Add a voice vlan Yes-table 00e0bb 3Com_phone___
VLAN voice Yes-table add 3475c 7 Avaya
LLDP-med-network strategy 1 voice-signaling vlan 20 v
hostname switch0a1172
line telnet
e c8e383b1dd7be99f878a387d87766e875404e0b3 password
output
Cisco c8e383b1dd7be99f8 encrypted password username
LG 15
The telnet server IP
!
interface vlan 13
192.168.11.1 IP address 255.255.255.0
!
interface vlan 20
no ip address dhcp
!
interface fastethernet1
spanning tree portfast
switchport mode access
switchport access vlan 13
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet2
spanning tree portfast
switchport mode access
switchport access vlan 13
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet3
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet4
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet5
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
fastethernet6 interface
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet7
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet8
spanning tree portfast
point to point spanning tree-type of link
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
description macro switch
No auto smartport macro
! next order is internal.
macro auto smartport unknown dynamic_type
!
interface fastethernet9
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet10
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet11
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet12
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet13
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet14
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet15
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet16
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet17
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet18
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet19
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet20
spanning tree portfast
point to point spanning tree-type of link
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
description macro switch
No auto smartport macro
! next order is internal.
macro auto smartport unknown dynamic_type
!
interface fastethernet21
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet22
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet23
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface fastethernet24
spanning tree portfast
switchport mode general
VLAN allowed switchport General add 13 unidentified
LLDP-med enable
LLDP automatic address management
No auto smartport macro
!
interface gigabitethernet4
switchport mode access
switchport access vlan 9
!
auto macro disabled
switch0a1172 #.
Hi Abdulrahman, the config seems kind of weird.
I have just by default of the switch and follow this document.
https://supportforums.Cisco.com/docs/doc-27005
-Tom
Please mark replied messages useful -
ISE 1.1.2 change of authorization with Avaya switches (5520)
Hello
I'm ise configuration to make the assessment of posture. I saw avaya my LAN and Core switches. The idea is once the user is authenticated using 802. 1 x, then it will be moved to qurantine vlan and after that it complies with the policy of the company then it will be moved to the vlan real. I have configured the switch avaya to accept the assigned vlan and also configured RADIUS authentication dynamic 802. 1 x. Currently, RADIUS assigned qurantine vlan works but once the nac scan agent and mark the status of compatible PC then the CoA is not the case, and user is not moved to the vlan real.
I tested the same authorization of the ise policy to assign dynamically VLANS on switches cisco and it worked perfectly, but the same thing is not happening on avaya switch.
Any idea on this?
Kind regards
Akhtar
Akhtar,
Posture with ISE flows have only been tested with Cisco switches:
http://www.Cisco.com/en/us/docs/security/ISE/1.1.1/compatibility/ise_sdt.html
The RFC says that port 3799 is for CoA, but due to a conflict, we use port 1700 so that my have something to do with it. That said we don't pretend to support 3rd party switches currently. If you do not want to see this please contact your Cisco account team to check the status of the part 3 switch support or request the feature.
-Jesse
-
Avaya for VCS SIP/h.323 neighbouring area
Hello
I found the former Avaya documentation on how set up a SIP trunk between the Manager of Avaya Session for Cisco VCS, but customer has only Avaya Communication Manager (Session Manager not) and both SIP and H323 endpoints registered to it. They want to set up an area of neighbor to a Cisco VCS, that also hosts H323/SIP endpoints. I don't see a problem with VCS VCS will ensure interoperability of calls but I understand Avaya CM does not Interworking caps and that's why we seek to put in place a trunk that can handle both voice and video calls SIP/h.323 on the side Avaya.
Ideas or maybe the documents that I have done to?
Thanks in advance
Yes, it should work.
I would advise use you a H323 trunk, but it will help save the traversal licenses (since calls interoperability course licensing) also, I found H323 trunks in the Avaya CM to work better (I have a slight tendency that I have a similar environment and use a H323 trunk with no problems.
Please note the answers and score the questions as "answered" as appropriate.
-
Problems with phones Avaya IP &; PIX 515
I have a setup where an Avaya MedPro/CLAN is connected to the DMZ with Avaya IP phones even inside with H323/225/323RAS s active correction and an access rule of DMZ within the LAN IP address, phones don't register. What IP is enabled MedPro/clan started to work inside the phones.
The PIX OS, I have is 6.3 (1), what is happening here? Any ideas would be much appreciated.
Thank you.
Disable any correction h.323, it does not work with the doorman avaya 'clan '.
no correction h225 1720 h323 Protocol
no correction protocol h323 ras 1718-1719
Then make sure
your static (inside the dmz) is configured correctly and the ACL have 1719/1720 tcp open
In addition, open range of udp ports that correspond to your avaya "area network server configuration.
-
Sign up for Cisco and Avaya CS1000 C40
Hello
I would like to know, is it possible to connect Cisco Telepresence C40 to Avaya CS1000 for audio conferencing
Thank you in advanced for your help
Best Regadrs
Titebiket Mohamed Yatim
Hi titebiket,
Avaya CS1000 is old nortel cs1000 systems supporting h.323/sip.
I think that you should be able to register as it supports standard protocols which, in my view, it does. Although I've never tried.
Concerning
Alok
-
Dialing SIP calls SIP Trunk (Avaya SM)
Hello. I work with the telco team to send sip of our endpoints VTC voice calls to an Avaya Session Manager.
I think I have all the areas and rules of research on the side of VCS in order to transfer the call to the SM. I am able to confirm with the team of the phone company that the call reached the SM, but they receive the error "cannot determine realm."
On the side of the VCS, I see the output below. Is the problem on the VCS or SM side? I need to create a trust with the SM? THX. - F
- searchRule (2)
- Name: SIP Audio out rule2
- Zone (1)
- Name: TEST Session Mgr
- Type: neighbor
- Protocol: SIP
- Found: false
- Reason: Internal server error (cannot determine the domain)
- StartTime: 2015-03-09 13:21:58
- Time: 0.05
- Access controller (1)
- Address: 172.x.x.x:5061
- Alias (1)
- Type: Url
- Origin: unknown
- Value: [email protected] / * /
Another option is to see if you get up with 5060/udp or 5060/tcp, which could make it easier to trace. But yes, I prefer the encryption as well.
Often you have set a kind of trust for a specific connection, which could include the field src or dst, ip, port,...
good luck ;-)
Maybe you are looking for
-
HP Pavilion 15-n220ca drivers windos 7
I hate windows 8, I have install windows 7 64 bit on my computer no UN HP Pavilion 15-n220ca, I can't seem to find drivers on the HP site can someone me rescuer pour find drivers for windows 7 64 bit
-
HP Envy 700-430qe PC: Installation of SSD
I just bought a HP Envy 700-430qe PC and want to install a new 256GB Solid State drive.(1) can I just use the factory reset HP recovery option to install OEM Windows 8.1 on this operating system? Since the splash screen?(2) otherwise, what happens if
-
I can access the folder by default, but not the default user folder. I read somewhere one of them is installed OEM and not of Win7, but which, is necessary?Thank you
-
Media Player is up-to-date and copies of all the music files added, I have 5 copies now
I can't find any way to stop this update and addition of copies of everything in my music files. I delete thecop ies and they keep coming back. There is no settings I can find to solve this problem, please help. Diane
-
Hello We need to connect from an external computer connected by cisco-vpn-client to an internal server that is behind an ASA 5505 with easy VPN config. The VPN connection with the customer at our 5520 firewall is good, but when I try to connect to th