Batteria per PowerEdge 2950 [MS] 6i controller

Similar Questions

• PowerEdge 2950 Perc 6 / i battery failed

  Hello

  We have a Dell PowerEdge 2950 that signals a failure of the PERC 6 / i battery. Where can I buy a spare battery? This server is no longer under warranty.

  Thank you

  Shang-Lin

  U8735 part number.  You might be able to buy them through Dell, but you can get them from many suppliers:

  http://www.Amazon.com/Dell-U8735-NU209-battery-PowerEdge/DP/B0045ZNJJU

  http://store.flagshiptech.com/Dell-u8735-nu209-P9110-PERC-5-i-6-i-H700-RAID-controller-battery/

  http://www.impactcomputers.com/u8735.html

• Upgrade of ram per server DELL PowerEdge 2950

  Buongiorno,

  necessitiamo di assistenza per UN PowerEdge 2950 venduto a nostro client nel 2008, by cui ormai fuori co (he e S/N FJ0C34J).

  It client vorrebbe fare della di 16GB ram upgrade.

  In attesa di risposta, in want pre-empted by attenzione

  Buongiorno,

  Unfortunately no vendiamo più banchi di memoria per questo modello di server.

  Who can find I banchi di memoria currently available alla vendita.

  Accessories.euro.Dell.com/.../genselector.aspx

  Marco

• riflettore ridondante da sul Server PowerEdge 2950

  Buongiorno,

  avrei need di UN preventivo per sostituzione di UN riflettore ridondante da by server it

  PowerEdge 2950 con number number {{Svc Tag rimosso dal intimate}}

  Fuori co.

  Grazie

  Speaking saluti

  Domenico Procopio

  Domenico,

  Reed is it Server e fine della vita, ancora cercare di way we can it number e lo stato parte. Corretta part links the di di corrente installata, cosi can way side tension.

• Dell PowerEdge 2950 Backplane - error message: SAS B missing cable. Misconfigured?

  We have a bunch of Dell PowerEdge 2950 s, they came with a built-in SAS Perc5i RAID controller.

  Unfortunately the Perc5i is a kind of fake raid 10 (a span of mirrors) rather than a bunch of mirrors so we had to get some raid cards appropriate instead.

  So now the perc5i on board is disconnected from the bottom of basket and disabled in bios, and we have our new raid card installed and connected to the bottom of basket - all is well and they work well.

  However when the machines bios startup stops and we get an error message saying the following:

  «SAS B cable missing /.» Misconfigured.

  Turn the system power off and connected properly. Details for the wiring of storage system information label and manual Ownders hardware.

  Press F1 to continue, F2 to run the configuration utility.

  How can we stop this message? This is obviously completely false; our new SAS cards are connected to the bottom of the basket and works very well. I don't see anywhere to disable this message in the bios or the 5 BMC Management utility.

  BIOS version is 2.2.6 (last)

  BMC firmware is 1.97 (last)

  Backplane firmware is 1.05 (last)

  Help, please!

  
  

• PowerEdge 2950: Disco con Volume Raid 5 [MS] offline

  Su winds del supporto tecnico vi sewn by take UN preventivo per sostituzione di UN difettoso disco.

  VI allégo i dati del disco del e Server

  Dati server:

  Chassis model PowerEdge 2950

  Revision III system

  Service of chassis number

  Dati dell open manage server administrator:

  Critical; Physical disk 0:0:0; Failed

  type: SAS

  136,12 GB capacity

  vedor DELL

  ProductID ST3146356SS

  revision HS09

  serial number 3QN091J5

  day 03. 41; 2008

  SAS address 5000C50004EDD38D

  Buongiorno,

  Offerta inviata: Offerta Dell n ° client 15509878: IT2786257 - TECNEMA TECHNOLOGY SRL

  * Offerta offers great al successivo giorno lavorativo (eccetto che in caso di problemi di reperimento parte) senza retreat del guasto *.

  Speaking saluti

  Manual

• PowerEdge 2950 HARD 500 GB SAS [MS] drive

  Abbiamo UN PowerEdge 2950

  Codice di matricola: |
  Codice di servizio rapido:

  Per questo Server above serve disco UN auswechseln: Seagate 500 Gb SAS 7.2 Potete fornirlo

  Potete inviarmi offerta al mio address e-mail:

  [email protected]

  Reference Dell SPA pulito gia' registrata come nostro fornitore

  Grazie

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione:
  1. company name:
  2 address:
  3 City:
  4 Provincia:
  5 cap:
  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione:
  1 nome società:
  2 via:
  3 City:
  4 Provincia:
  Heading 5:
  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:
  7 partita IVA

  Speaking saluti

  Manual

• PowerEdge 2950. Need advice to add 1 TB SATA disk.

  This is my first post.

  I have a PowerEdge 2950 with PERC 5 / i.  The firmware version is 5.2.2 - 0072.   Configuring PERC controller 0 shows.   0 to 2 physical disks in SAS controller.  2 physical disks are used to create a virtual drive.  The virtual drive is used as the C: drive.  Readers of the excellent work.

  

  I want to add a 1 TB SATA drive which will act as a stand alone D: drive.  I had planned to add the SATA controller drive 1, but when I run the PERC configuration utility, I don't see a setting 1.

  What should I do to add a 1 TB SATA drive?

  

  Looks very good.

• Dell PowerEdge 2950 P2V problem

  Physical server:

  Dell PowerEdge 2950

  Windows 2003 R2 Standard x 86 operating system

  Sheet music:

  Dell - hidden partition

  C: BONE

  D: Data1

  E: Data2

  F: Data3

  G: data4

  vSphere ESXi 4.1 (under license)

  ISCSI SAN

  vCenter Server

  I tried on cold hidden server with boot CD, but received the error "unable to determine the operating system invited."  Looks like that I don't have the driver for the Dell raid controller in the boot CD.

  I decided to go with the hot P2V using the plug-in for VirtualCenter.  I stop the SQL server service and disabled the firewall disabled the anti-virus tools.  Only two partitions (C and G) on the physical server must be in the new virtual machine.  So, I've selected partitions C and G and has increased the size of the drive at a time.  I made sure not to install the vmware tools and unchecked the option reconfigures.   The P2V conversion was successful.   But when I went to start the virtual machine, it starts with the 'VMWARE' logo and restarts immediately.  Restart the virtual computer so fast I can't even in the BIOS unless I hit the key several times.   I did the clonning with the hidden partition, but with the same problem.   There are no BSOD or any indication that the virtual machine cannot find the vdisks.   Called in vmware support.  They used webex for an hour, but could not fix.  Asked me to send in the logbundle.

  I HERE it if someone tell me what I am doing wrong?

  Thank you

  Another option is to install the Standalone Converter 3.0.3 on the PowerEdge, stop all services and performing the conversion.

  André

• ESXi 3.5 on Dell Poweredge 2950 and Dell 6 GB/s card SAS HBA?

  Hello.

  I'm under ESXi 3.5 u4 on a Dell poweredge 2950 machine.

  I recently bought a Dell Powervault 124 t. autoloader with a HBA SAS 6 GB/s card.

  I installed the card SAS in the PE 2950, but now I can't seem to see in ESXi.

  Can someone help me with this?

  Thank you very much.

  I'm afraid that the Dell technician is correct.

  Someone at - it a link on ESX support not directly connected devices?

  This isn't the issue. The question is: do you have a link that shows devices supported?

  Reference Dell does support the autoloader Powervault 124 t. on ESXi 3.5?

  Have you checked the VMware HCL already, if the SAS controller is included/supported for ESXi version, you are running?

  There are a few articles which have tape readers running with Adaptec SCSI controllers, I don't see anything for ESXi 3.5 with a SAS controller still...

  Maybe there's a better chance to make this work with ESX 4.x with VMDirectPath

  André

• II of the PowerEdge 2950 not allowing for space HARD to be accessible

  Nice day

  I have an old server PowerEdge 2950 II (card: 2x3.0 Ghz Xeon, 24 MB Mem 1 TB SATA HDD, 1 Tb SATA HDD, 2 TB SATA HDD - Server data center in 2012).

  The question I have is that I recently updated the operating system from 2008 to 2012 DC, then installed an extra drive (2 TB).  I run RAID 0, and the system is only show a MAXIMUM of space disk HARD 1.98 TB, with the other Tb 0.02 table allocated to file systems.  RAID Perc 5i controller has all the three marked as online HARD drives.  BUT I can not use the additional 2 tablespoons in the table.  I was going to buy and install a 2nd HARD drive of 2 to SATA and RAID 1 go; but, if I can't fix this storage space not represented in the storage Bay I can't justify the purchase.  If anyone can help I would be grateful.

  So, you have three disks - 1 TB, 1 TB, 2 TB - during a RAID 0, and you expect to see 4 TB of space?  If so, see my notes above.  Each virtual disk (RAID array) is presented to the operating system as a separate 'disc'.  Windows cannot use a more 2 TB drive unless it has been converted to GPT.  First of all, the conversion to TPG is data destructive, so you will need to do a backup/restore.  Secondly, convert your boot 'disc' TPG will not cause it to start on a 2950 because it only supports UEFI, which is necessary to start from a GPT disk.

  Bottom line?  You need to rethink your configuration on this machine.  You could make two 1 TB disks in a 1 TB RAID 1 for the OS (in MBR and bootable on a 2950), and then you could add 2 TB RAID 1 for data disks.  2 TB, it would be unnecessary to convert to GPT, but if you have added more than 2 TB of space, you would then convert that TPG and use as many TB for the data that you can hold in the system.

  In addition, you realize how dangerous running a RAID 0 is, right?

• PowerEdge 2950 Boot

  Hi, I'm not a person of material at all, so please be patient with me.

  I recently acquired two PowerEdge 2950. Currently, I don't have any operating system installed, and I don't know if two hard disks that came with it are truly functional. I install two hard drives on the server and put under tension. Hard drives blinked once and the indicator remained offshore. I try to enter the raid controller to see if yes or no hard disks are working, or showing upwards, as suggested by my work.

  Supposedly should have an option (Ctrl + R) on start up to enter THE RAID controller BIOS, but its lack of my server for reason. I thought that the bio for server was old, therefore, that I have updated to the latest (2.0.7 I think). However, it now shows the option. Then, I thought that maybe the RAID controller is not recolonized by the server, so I unplugged the RAM RAID controller and started the server, but resulted in an error indicating that the RAM is missing.

  All of the above are the same in both servers I have.

  At the end of the day, I am just installing a server on these servers operating system and now the hard drives are not recognized by the server.

  Please help me with this problem.

  Thank you

  Qun

  qungg

  When I plug the RAID controller, the built-in RAID controller option does not appear in the SETUP (F2)

  It's normal, but it shows that the controller is at least very little functional. Most of the hardware failures cause a piece dead circuits, but rather of bad operation of the circuits.

• Secure Hard Drive wipe for Poweredge 2950

  Hello, I recently got a hold of a Dell Poweredge 2950 but until I can do something with it. I need to clear safe hard drives with killdisk (or something similar that will provide newspapers) and I have problems with what I believe, it is the raid controller. I followed these instructions

  http://sysadmin-e.com/securely-wiping-hard-disk-drives-on-Dell-PowerEdge-servers-with-BartPE-and-kill-disk

  and came very close, but it did not work. I have when I get on the use of killdisk for windows, I am able to see the virtual drives all named with the perc 5 / i but later I receive errors when trying to erase the drives. I'm starting to think that it is not possible at this point, the Active Server, but I wanted to see if anyone had experience with this or advice and assistance. Thank you.

  Why do you need to erase the discs on the receiving server safe?  It is usually the responsibility (desire and political) of an organization, before getting rid of a system/disk.

  Are these SAS or SATA drives?  You could attach them to a JBOD controller (PERC 5 support NOT of JBOD/no RAID), and then do the wipe directly to disk without the need to manage virtual disks on the controller.

• (Redirected) PowerEdge 2950 - disk failure

  Buon giorno

  HO a PowerEdge 2950 cui non riesco a qa Server da collegarmi console (window sin corso accesso).

  failure of disco 3 he display tell

  STO pensando di riavviare comunque server of it

  My devo acquistare UN disco in sostituzione.

  Come posso fare.

  Grazie by it support

  Sartore franco-

  ADMIN NOTE: replace character removed according to the TOU >

  Best of this post in the Forum servers, here:

  http://en.community.Dell.com/support-forums/servers/default.aspx

  Bev.

• PowerEdge 2950 III w / Server2008 64 bit: cannot activate TOE

  I recently purchased a PowerEdge 2950 III with standard options, which includes a double NetXtreme II Broadcom nic with TOE capabilities. Due to some communication problems, it was delivered without active TOE and the TOE installed key. I installed Windows Server 2008 64 bit on it.

  After some time Dell send me a TOE key, and I off the server and installed it.

  In the BIOS, it now says "able TOE." In the Dell OpenManage Server Administrator it said ' able TOE: available 'and' enable TOE: 'Yes. But in the Broadcom Control Suite to unload his abilities he doesn't list that the LSO and CO, PINCH.

  I have tried several things:

  -J' ran "netsh interface tcp > set global chimney = on" to activate TOE

  -disabled the Windows Firewall

  -remove the Broadcom drivers and reinstall them (the more recent on the Dell site)

  -installed the SNMP functionality

  But I can't seem to make it work.

  TOE benefits to the whole Server 2008? If so, what am I doing wrong?