BDP-S580 white screen after startup

Similar Questions

• Satellite A85-s107 - white screen at startup by using the power of the battery

  Satellite A85-s107 white screen at startup by using the power of the battery

  When I boot A85-s107 in battery power, it is get booted up in the background, but my screen is empty.
  After that if I connect it to AC power and switch deactivation/activation of the laptop power button, the screen comes back to life.

  There is no problem when I start upward when it is connected to an electrical outlet.
  Battery is fully charged and computer will work off the battery voltage if I remove AC after boootup

  Any suggestions?

  PS:

  also note that when I remove AC and then reconnect I start the computer on two occasions that it does not start the 1st time?

  Don t need to recharge the battery if the AC adapter is plugged ;)
  Try the tips posted by Alex otherwise it of a hardware problem, in my view, there seems to be something wrong with the motherboard...
  In this case, only the replacement could help and it could be a costly affair

• White screen after log-in

  I have a white screen after login, but it lasts for about 30 seconds my desktop appears.  Any ideas?

  I ran Microsoft Security Scanner and everything out very well.  I have McAfee Anti-virus works as well.

  Hello LA_Hay,

  Thanks for posting your query in Microsoft Community Forum.

  You did it any significant hardware or change software on the computer before this problem?

  A problem with the card installed on your system, might be a major cause of the problem. So, I would suggest trying the following steps and check if the problem persists.

  Method 1:

  Step 1: Try to start your system in a State of services necessary to the operation and a minimum set of drivers enabled, called Safe Mode.

  Start your computer in safe mode

  Step 2: If you do not have the white screen in safe mode, try to clean the system startup:

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

  Note: See "How to reset the computer to start normally after a boot minimum troubleshooting" to reset the computer to start as usual after a repair.

  If the problem persists, try Method 2.

  Method 2:

  Update your graphics card.

  1. Open Device Manager by clicking the Start button, click Control Panel, click System and Security, and then, under System, click the Managerof peripheral . If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. In the list of hardware categories, find the display adapters and select the device driver you want to update, and then double-click the device name.
  3. Click the driver tab, click Update driver, and then follow the instructions. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, visit the below mentioned link:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If you are not able to update the device driver via windows update, you can visit your computer or graphics card manufacturer's Web site and download & install the latest driver.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Computer laptop white screen at startup

  A few days before, at a bend on a laptop, the screen remains blank (was not lit at all) but the computer sounded as if it was put into service. What are the possible causes for this problem?

  Hello Pierre,.

  Thank you for using Microsoft Community.

  1. does the computer boot to the desktop, or you see the white screen on startup of the computer?
  2 did you change on your computer?
  3. What is the brand and model of the laptop?
  4. as you mentioned, "when you turn on your laptop, the screen remains blank (was not lit at all) but the computer sounded as if it was put into service ', what exactly happens when you start the computer?

  If you get white screen SAT after the start of the desktop, then I suggest you follow this article and check.

  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Important notes:
  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  Please answer with results so that we can help you further.

  Thank you

• Apple MacBook Pro with a white screen on startup, help!

  Hello world

  I was the creation of a powerpoint for an AE conference is next week and while running my Mac screen is temporarily deformed and then turned to white. I left for a while and then held down the power button to restart. On this operation, he got successfully to the stage where I enter my password, then displays the bar loading. At mid-way through charging it cut to white again and reworded. I then repeated several times, same result.

  Solve by looking at the options online, I tried following technical success:

  Command-R power on: goes to the white screen after the chime.

  Command-option-R-p: goes to the white screen after the chime and apple logo.

  Command-shift: enter the stage newspaper but then white screen.

  Command + S and fsck - fy: mac says is 'OK', rebooted and got the white screen after the chime and apple logo.

  Connected to the mac to work with cable Thunderbolt: mode target open successfully, but the drive does not appear on the mac to work.

  What can I do else?

  There is no apple in my store.

  This is a 17 "Mac Book Pro with El Captain OS X (don't know which) no history of problems...

  I hope someone can help.

  Freya

  Try resetting the SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

  If you try a safe boot, just hold SHIFT when the computer comes on, not Command-Shift.

  In addition, if you can get to the login screen, try to hold SHIFT while you connect to your account (not while you type, but when you have finished your password and immediately after pressing enter/return).

• HP Jet 11: White screen at startup

  My 11 HP workflow starts with a white screen on startup. Sometimes responds with a hard reset but still does not work. Have changed the settings to do nothing when the lid is open or start button / stop is pressed, but still problems.

  Hello

  Thanks for posting in the Forum from HP Support. Welcome!

  Looks like a problem of driver for me.

  Please, use HP Support Assistant = > http://support.hp.com/us-en/document/c03467905

  Make sure that you have applied all the latest drivers and updates from HP.

  Please, use Windows Update and check if you have installed all the latest patches.

  I would like to know if it works for you.

• Satellite P300 - white screen after waking from sleep state

  I'm having this problem:
  The LCD screen may be empty when the computer is "awakened" from the sleep state. Nothing is visible on the internal LCD or an external monitor.

  There seems to be a solution:
  An update of the firmware for a component in the main circuit of the computer solves this problem. This update must be performed by an authorized Toshiba (ASP) Service provider. Until arrangements are made for the update, restart the computer by pressing the power on button for a few seconds.

  described here: [white screen after awakening from fallback status | http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_dtlView.jsp?soid=1642844&moid=1209152]
  -----
  I also found this, but it didn't really help me much further.
  [Satellite P200D and WinXP: no display after waking from sleep mode | http://forums.computers.toshiba-europe.com/forums/click.jspa?searchID=880412&messageID=118143]
  -----
  In fact, I think I'm able to solve myself, and I don't like not my laptop to be gone for two weeks or more. I just need some advice on where to find a correct upgrade. Is - this driver BIOS or graphics? Which version should download, where... etcetera. More tips on how to solve the problem are also welcome.

  -----
  Edit: link and no need for words of line. : s
  Edit2: grammar correction.

  Hello

  > An update of firmware for a component in the main circuit of the computer solves this problem. This update must be performed by an authorized Toshiba (ASP) Service provider. Until arrangements are made for the update, restart the computer by pressing the power on button for a few seconds.
  If you check the Toshiba document you would see that your Satellite P300 is not related to this issue.

  In your case I would recommend upgrading the BIOS and graphics driver.
  In addition to keep your operating system up-to-date.

  I had this problem under Win XP and a MS patch and an update of the graphics card driver helped solve this problem.

• white screen after the signing, the

  I have a laptop HP 2000 who now has a blank screen after I connect. I've removed ask.com because it never works and when I restarted my computer I get this white screen after the signing, the. I can still see my settings or start menu. What can I do to solve this problem. Help, please.

  Hello

  Try the following.

  Boot the computer normally and log.

  Black screen, old the ctrl and alt keys and press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When the system restore interface is loaded, choose a restore point at least 48 hours before the opening of the session the question first and then proceed with the restoration of the system.

  Kind regards

  DP - K

• PavilionDV4T-1400 white screen at startup

  I have a Pavilion DV4T-1400 , who immediately becomes a white screen on startup. I have no options. This happened out of nowhere.

  Here is some information:

  -Locks caps/scroll/num doesn't turn on when I press on the

  -It has a slight smell of burn on it when I turn it on

  -J' tried a hard reset (power off, then press on and hold power)

  -J' I tried to delete the memory, that I get no beeps, just a black screen and the scrolling/caps lock lights will Flash 4 times

  -J' had the computer almost 2 years warranty for 1 year.

  -J' have the knowledge/skills to remove and replace the maps system etc.

  I'm looking for some advice, or what someone might think the problem is, so I know what to replace.

  Any ideas? It is greatly appreciated. Thank you.

  Anything it is displayed on an external monitor? If so, it's the screen or the cable and not the mother/gpu card. If this isn't the case, the new, it's worse. According the description, of course looks a catastrophic failure of the motherboard. The slight burning smell is really a bad sign.

  Here's a motherboard on ebay:

  motherboard

  The price is a little high but lower than HP would be. Go down you $ 20 for a Exchange. There are also several services advertised on ebay that will repair your device for about the same price or a little less.

  Here is the manual if you choose to DIY:

  Manual

• White screen on startup after conversion

  Hello

  I converted a 2003 server. It seemed to have been successful.

  In workstation (version 5.x), when I tried to add the machine, it starts from upward, but after the screen of vmware it comes up with a white screen.

  Any ideas please?

  I would not use the server 2003 CD but a LiveCD - its much easier to make these controls with a regualr LiveCD.

  For a 2 k 3 System I would use something like BartPE or that I do--see my signature.

  To verify the assets-Pavilion open diskmanagement in the LiveCD and check if the C: drive is marked as bootable

  ___________________________________

  VMX-settings- VMware-liveCD - VM-infirmary

• White screen after login (Vista)

  After updating my computer this morning, the screen now becomes white after I connect. I looked around for finding bugs, but so far I can't make anything of them because my screen does not return to normal. I tried to put it to sleep, hit escape and using the Windows key on my keyboard but I get no response from either of them. CTRL + Alt + Delete displays the usual screen, but none of the available options help to solve the problem.

  Translates into a safe mode black screen after log in and the same problems.

  I would try to do a system restore, but I don't have a disk for Vista.

  Hello

  A white screen may have the same root cause as a blackscreen and be too difficult to treat. Try
  This generic troubleshooting remember black and white the same fix would work. See following message
  If you can't at least win a minimum level of access work.

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have your system disks
  manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore there only to)
  being bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - type no parenthesis)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• White screen after starting the desktop computer

  Original title: Windows 7 white after the start of desktop screen.

  When windows starts my desktop appears for 5 seconds and then the screen become white. I can't do any of that except the computer restarts.  When I do this, white screen closes and I see my office, but which also closes and the system restarts with the same question.   It seems that something is loading right after my office that does not... I can't access to my office to see what is on... Any thoughts on how I can fix this, other than a system restore?

  I have a solution

  First of all causes of white screen most of the files exe as spyware or viruses is the best way to solve this boot

  on winpe CD or DVD from winpe, the research of malicious software which load at startup

  If you don't know what file is it tries to start the Task Manager when connecting

  to do this, go to system32 and then make a copy of cmd.exe and rename the copy sethc.exe and replace the current sethc after this restart let it connect normally, then pass the user pressing a win + l and then press SHIFT 5 times then a command prompt should appear then type taskmgr.exe and then find the process and kill it and remove via msconfig or winpe sorry for my bad English

• Satellite M50 - white screen after login on Win 8.1

  Satellite M50 running 8.1 Win
  After login, download mouse white screen, but nothing else.
  Can run Explorer.exe manually via the the Task Manager for go, but some applications like Acrobat and Windows Mail does not work.

  I searched online and tried all sorts of fixes suggested without result.
  Any suggestions gratefully received!

  I don't know what the problem is here, but you can try to Win8 will stop completely and check the repair options. Try again with the system restore and roll back the OS a few days back. Maybe this will help.

  http://APS2.toshiba-tro.de/KB0/TSB2A03ES0000R01.htm

• Satellite Pro L300 - white screen after login

  Hi, got a laptop off a friend to watch as not start correctly. Vista Edition running Home Premium, it will start up the screen of the user ok but when a user is selected the screen goes white with just the mouse pointer showing (which moves ok on the touchpad). I can press Ctrl Alt Delete and get the blue menu screen - if I try the Task Manager with it it goes back to the white screen.

  I tried a repair of end upward to F8 but said no problems found. I can also start ok in Mode safe without getting a white screen. I tried a high diagnostic of MSConfig startup but still the same. I also disabled all services but still a Virgin.

  I have a secondary partition on the disk with the recovery of HARD drive there, but do not want to reformat. I tried to restore to several different, but restore points remains empty at the normal start screen.
  Someone at - it find it.
  Mark

  Hello

  Its hardware problem or software.
  Start the laptop in safe mode means that some essential software process would be disabled and the system would use only a few basics of essential equipment.

  So even if the laptop runs correctly in safe mode, it could be a hardware problem.

  That's why I think only with the help of HARD drive recovery would be the best way to know what's wrong here...

• Portege Z930 - white screen at startup

  My Z930 screen is empty at the start. The cursor can be seen when is moved around the screen, but there is no
  background a screen empty. stop holding the Start button / stop does not seem to work and the DSS led flashes slowly. When you open the lid of that unit starts automaticlly displays white screen and the cursor.

  I'm a computer completely illiterate, but if anyone can help me in words laymans terms, it will be a great help

  > now the button stop / stop does not seem to work

  That s is really bad.
  Due to Toshiba power button on document - http://aps2.toshiba-tro.de/kb0/FAQ3500560002R01.htm - should have the double function.
  Unplug the power plug and press and hold the power button / stop. I think the laptop must be turned off after a few seconds.

  Are you able to turn off your laptop somehow?
  Can you please elaborate on this subject? Since when did you notice this?
  Have you done something before your laptop started acting in this way?