BEFW1154 to a SE567

Similar Questions

• C309 HP Photosmart Premiun... printer offline

  I have all in one printer hooked up to my office, he has no problem printing.  It will not print using my Toshiba labtop, it did when I first came I, t is no problem. I called using HP and we managed to fix it by installing everything on again on the labtop, new drivers, etc. I'm working on a router, this option 2 office and my labtop (Gigaset SE567 of Telus). When I go to devices and printers, and the HP photosmart series page it says the printer is offline? Any ideas? I hope I explained it well enough. Thanks for any help

  I would like to try the following steps:

  1. Go to the control panel-> display devices and printers
  2. Double-click the printer
  3. Go to printer menu and then click Properties
  4. Click on the Ports tab
  5. Choose Standard TCP/IP port, and then click the Configure Port
  6. Make sure that the IP address in the field "printer name or IP address" matches with the IP address of your printer in the diagnostic report
  7. Try to print a test page to see if it works

  

• Do I need a new wireless router?

  Has been said by Virgin that although their modem accept 20 MB, my wireless router (a 4 years old Lynksis BEFW1154) won't let me get the faster speeds. As a "silver surfer", I could argue the point with their advisor, because honestly I don't know what he was doing on. What I know, is that I pay a monthly display for flow rate of 20 MB, and having control of internet speed, all I get is 3.3 MB download and 0.9 MB Upload. Do I need a new wireless router? Any constructive suggestions would be much appreciated

  Thanks a lot for your answer. I'll go to local store and explain my problem and tell them your suggestion. I'm sure that they will be able to help. Very much appreciate your help.

  Concerning

  Allycutter

• WRT54G disconnect problem

  I've been a loyal user of Linksys (CISCO) since the purchase of my 1 Access Point wireless router and 4-port Switch (BEFW1154 v2) in 08/2002. I upgraded to a Linksys Wireless - G Broadband Router (WRT54G v8.00.2) 11/2007. My home wireless network supports; IBM Thinkpad (Windows XP) and Lenovo Ideapad (Windows VISTA Home Premium). A month ago I started having disconnect problems with the WRT54G. The two laptops have been disconnect it. At first I disconnected the supply WRT54G for about 1 minute then plugged in. This has not solved the problem of disconnection. I then tried to unplug the cable modem and power WRT54G. Wait about 1 minute and then reconnect the cable modem, allowing it to reset and synchronization. Then I plugged the WRT54G. This temporarily solved the problem for a few minutes but the disconnection problem returned. I have reset the WRT54G Setup factory default and reconfigured it to my home network. The disconnection problem was not solved by taking this action. I contacted Cablevision that provides my broadband Internet access. They could not identify a root cause of the problem of disconnection. To determine whether the root cause was another thing that the WRT54G, I reinstalled the BEFW1154. I did have a problem of disconnection from taking this action leading me to believe that the WRT54G is bad. I would appreciate any suggestion that could solve the problem of disconnection with the exception of a suggestion to buy a new router. Thank you

  Good to hear that!

  Please click on 'Accept as Solution' to the post that solved the problem so whenever someone meets the same, they immediately know the answer. Thank you.

• Vista wireless loses Internet access after the mode "Eve".

  Environment:
  HP Pavilion dv2610ca notebook PC, broadcom 802. 11 b / g adapter, Vista Home Premium 32 bit SP2, Siemens Gigaset SE567 router/modem.

  Problem:
  I can usually connect wirelessly to my home network and to the Internet whenever I start my computer. However, I have close the lid and leave it in standby mode, I can't access Internet after I opened the lid and the system wakes up. The system connects to my home network but cannot access the Internet. It shows a Local access only.

  Diagnosis and repair fails generally, telling me that I have a problem with my router. Disconnect, then reconnect usually works. My router power market also works.

  I saw lots and lots of issues with Vista wireless networks and I followed several of the recommended actions:
  -updated the driver broadcom
  -reset the IP stack by using the tool "Fixit" of Microsoft
  -disabled the use of IPv6 in two by disabling the check marks in the related devices and changing the registry TCPIP6 parameters
  -modified the registry to activate/disable the DHCP broadcast flag in the TCPIP Interfaces
  -J' tell the system not to disable the card Broadcom, but the "Power management" tab mentioned in some articles does not appear in its properties. The only reference to power is "Minimum energy" under the "Advanced" tab, then I disabled who.

  Nothing has solved the problem.

  Has anyone else had this problem and fixed it?

  I'm not a technical Wizard, so please provide instructions for any action that you suggest.

  Thank you.

  I replaced the Siemens router/modem provided by my ISP (Telus) with an old D-Link router and separate modem 3Comm I had been using a couple of years and the problem seems to have disappeared.

  I'll close this thread on the assumption that the problem will not rear its ugly head again.

• does anyone know how to fix NAT TYPE failed for the PS3?

  I tried to play modern warfare 3 online for the past few days, and this is the first time that I had this problem when I bought the ps3 I just signed up to the playstation network and put it in my drive of cod mw3, I didn't have to open all ports or whatever it is, I played for about a year and a few days ago I turned on my ps3 and tried to play and nothing happened so I checked my connection and everything was connected, Internet, ip, and sony all have works well but my nat type has been down for about a week now, I reset my modem several times, I have a Siemens Gigaset se567, I tried the connection cable and wireless and Sony, I opened the ports I had and DMZ on always I net type Failed. so if anyone can help me it would be greatly appreciated. Thank you

  We have a separate community for Playstation products. Please click here for assistance.

  If my post answered your question, please click "Accept as a Solution."