Vista wireless loses Internet access after the mode "Eve".

Similar Questions

• Windows 7 hangs 3.5 minutes after the mode "Eve"

  Install Windows 7 upgrade from vista. Everything works well, but crashes after the mode 'sleep'. takes 3.5 minutes to thaw. Have a hp pavilion a6707c. Vista was faster to return to that.

  Don't know if this helps, but after I disabled the hybrid sleep I can hibernate and that it only takes 35-40 seconds to resume and everything seems to work fine.

• No Internet access after the connection of the cisco vpn client

  Hi Experts,

  Please check below config.the problem is vpn is connected but no internet access

  on the computer after the vpn connection

  ASA Version 8.0 (2)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.10.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 192.168.14.12 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
  INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
  55.240
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool testpool 192.168.14.240 - 192.168.14.250
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access INSIDE_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.14.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
  Crypto-map dynamic dyn1 1 set transform-set setFirstSet
  Crypto-map dynamic dyn1 1jeu reverse-road
  dynamic mymap 1 dyn1 ipsec-isakmp crypto map
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  password encrypted user testuser IqY6lTColo8VIF24 name
  username password khans X5bLOVudYKsK1JS / encrypted privilege 15
  tunnel-group mphone type remote access
  tunnel-group mphone General attributes
  address testpool pool
  tunnel-group ipsec-attributes mphone
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
  : end
  ciscoasa #.

  Hello

  Large.  Try adding the below to make it work

  vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

  NAT (inside) 0-list of access vpn-sheep

  Harish

• Lose Internet connection after the "sleep mode"

  Original title: whenever my windows 7 fate of Eve he always loses its internet connection

  When I run the trouble shoot it says I have an invalid ip address. It's the same thing if I leave a link to the other. I don't understand why he's doing this help please

  Hello

  Were there any changes made on the computer before the show?

  Method 1:

  I suggest you to disable the IP assistance service and check.

  (a) hold down the Windows key and type R, type "services.msc" (without the quotes) and press on Enter.
  (b) scroll down for IP assistance service, right click top and select Properties.
  (c) in the drop-down list that says "Automatic" or "Manual", set it to disabled and then click 'apply'.
  (e) then click on 'Stop' to stop the service from running in the current session.
  (f) click on OK to exit the dialog box.

  Method 2:

  If the problem persists, you can disable Internet Protocol version 6 (IPv6) components and check.

  Follow the steps in the article to disable IPV6:

  How to disable certain Internet Protocol version 6 (IPv6) components in Windows Vista, Windows 7 and Windows Server 2008
  http://support.Microsoft.com/kb/929852

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base :
  322756 (http://support.microsoft.com/kb/322756/)
  How to back up and restore the registry in Windows

  Method 3:
  If the problem is not resolved, change the setting of the power of the network card and check.

  (a) click the Start, type devmgmt.msc and press enter.
  (b) to expand the network adapters and double click on card Wireless.
  (c) go to the power management tab .
  (d) are of course all receivers are unchecked.
  (e) when you have disabled the boxes click ok and restart your system.

  Put the computer in mode 'sleep' and check if you still have any questions.

  Method 4:
  If the problem persists, you can uninstall and reinstall the network drivers and check.

  Uninstall the drivers of network from the Device Manager, then restart the computer to load the generic drivers.
  
  1. click on Start, type devmgmt.msc in the start search box and press enter.
  2. right-click the network driver and select Uninstall.
  3. restart the computer.

  Check out the link:
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this information helps!

• lost internet access after the connection to the server

  Have had this problem in the past and in the hope that a workaround is available.

  MAC OS X El Capitan worm 10.11.2 runs and loses the Internet when connected to a server/sharedrive(on Microsoft Windows environment).

  You asked the same thing, or a similar, issue in October 2014. What happened after that?

• The VIsta calendar reminder is not pop up after the mode "Eve"

  Hello

  I had put a task reminder in the calendar from Windows Vista program.  But did not recall. I put usually PC mode 'sleep' when finished. So I tested if that did anything. So, I had an appointment for 12:15 and had reminder 5 minutes before.  Put the PC in 'sleep' to 12:00 and he works at 12:20, but the reminder of the calendar has no pop up, even after some time. It arises in place when I open the calendar program.  Even if instead of mode 'sleep', if I shut down the PC and start the reminder immediately opens. If "sleep" mode somehow put reminders in the sleep forever.

  Does anyone have idea about this bug?

  Thank you

  I don't know a solution. It does the same thing for me. I use the Outlook calendar. The Live, or Google Calendar likely would do anything as well.

  Messages rating helps other users

  Mark L. Ferguson MS - MVP

• No Internet access after the update from Windows 7

  Since the update of Windows 7 (from my list of update I can not single out one specific) sent 15 Dec - my computer will access my internet connection - the only way that I can access is to do a system restore to a point to Dec. 14 or before - I have a new computer - and no new programs have been added to the system during this time - it becomes troublesom because I have to constantly to do system restore to get online

  I called Support Center, Monday - and after having him work for almost 2 hours, we decided that the KB2467659 update is the culprit and we have disabled this update to be installed - HOWEVER the windows update program was H - LL BENT on installing this update - the technician called me back 2 days later Wednesday--and we did other things magic to ensure that this implementation to day has NOT been installed again - so far (knock wood) No recurrences of the problems

• Satellite A100-386: no internet access after the new XP installation

  Hi everyvody!

  I can do it myself, so I ask for your help!

  I have a Toshiba Satellite A100-386 with windows XP MCE.

  I recently had a virus, so I formatted my drive. I don't have the installation CD with me, so I install XP.
  I have two disc on my computer with the system and the other with the documents.
  Then I install ALL the drivers I could find on the Toshiba site for my computer.
  This means that the PSAA9E. The problem is that I have no internet! I don't understand why.

  When I look in computer management, I have no ethernet, controller mass storage controller and network controller.
  I have zone alarm as a firewall and an antivirus avast!

  I disabled avast to be sure that he's not in it but no result...
  In Thoshiba drivers there is also something to update the BIOS.
  I did it but I didn't change. I hope the problem here not there...

  It will be really nice to help me ^^

  Hello

  I think that you just have not installed the right driver LAN and WLan driver

  As much as I know this laptop supports Intel Pro 100 Lan and WiFi Intel 3945ABG card card

  Please visit the European driver Toshiba page again and download the compatible network driver and the driver WLan.
  Unpack the packages, then install it.

  Finally check again if the LAN and WLan cards were recognized in the Device Manager in network adapters.

  Good bye

• Firefox loses internet, resumed after the closing.

  I navigate on firefox, facebook and youtube, and then after awhile, everything stops load correctly. If I click on a link, it seems fair to charge forever, youtube videos will be stopped even loading at halfway. However, as soon as I close and reopen it works fine. No one else on my network is having these problems.

  I just reinstalled Version 6, resolved.

• HP ProBook s 4540: the screen goes black after the mode "Eve"

  Hello!

  My computer works fine but there is a problem, when I do not use it for a few hours or maybe an hour my screen goes black and it is nothing to do, but closed and then turn it back on.

  I have disabled all parameters almostly, screenshots here:

  #1- http://i.imgur.com/zelMPLD.png

  #2- http://i.imgur.com/FJNyLzi.png

  I don't know what to do, I think it goes to sleep after a certain time and then he don't wake up, I need to remove the battery and then turn again, he started arrive about 2 days ago when I updated my radeon HD7650 to 15.11.1 Crimson video card driver or sth.

  Hello

  Try disabling the startup of Windows 10 hybrid - you can do the following.

  Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

  In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, close all open windows, and then restart the laptop.

  Kind regards

  DP - K

• Windows 8 | Cannot start windows after the mode "Eve" [Mobile]

  Separated from this thread.

  Hello

  I have the same problem. I put my laptop (windows 8) to sleep and after a few hours when I tried to open it, it was just a white screen. I tried everything you mentioned (windows + w, windows + x, windows + r), but all in vain. Only thing that responds is increase/decrease brightness and volume. Help, please. Also when I try to stop him, he falls asleep.

  Hello

  Thanks for posting the query on Microsoft Community. You have reached the right place. Let us work together to find the cause of this problem and try to solve.

  Update you the drivers for graphics cards?

  If you have not updated the graphic card drivers, then I suggest you to update the drivers of graphics card on the manufacturers website and see if that helps.

  Troubleshoot video card
  http://Windows.Microsoft.com/en-AU/Windows-8/find-install-display-drivers

  I hope this helps. Let us know if you have other problems with Windows in the future.

• ulitmate local Vista only after the mode "sleep" loses the IP address each time.

  Ulitmate Vista wired ethernet.  After the mode 'sleep', 'local only' on awake.  Loses to IP address each time.  IP address needs to be reset.

  Hi C.Jaye,

  You can check out the following link and try the steps to solve the problem:

  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/thread/f21fcdda-4372-469d-b983-f4bd50d7f81d

  You can also read the following article and check if it helps:

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• After that Windows 7 conclusion "No Internet access" in the wireless network?

  I have a USB wireless network card installed in my office. All judging by the "connected network" showed, that he manages to connect to my wireless router, with I can't visit all websites due to "free Internet access". Only if I move my router where (almost) no wall blocking the path between my office and the router, will be solved the problem.

  There is no problems surfing the Internet using my laptop (Windows XP) and the iPad, which also connect to the router.

  I don't know what "No Internet access" while "Connected network" appears. To understand this, perhaps I should know what Windows 7 draws the conclusion "No Internet access" to the wireless network.

  Thank you, everyone. I managed to figure out the problem last night. With this document that I found by Googling, http://www.usb.org/developers/whitepapers/327216.pdf, I tried to disconnect my DVD ROM USB plugged next to my wireless network card and found that this really WORKED, although the DVD ROM is USB 2.0 instead of 3.0.

  In addition, as Shawn "Cmdr" Keene [MVP] said, I really need to I ignore the message "connected network". I ran the Ipconfig/all command frequently and found that sometimes the IP address of my wireless network card was no longer * 192.168.0 and the gateway, and the IP addresses of the DNS servers are null, even if the message "Connected network" remained all the time.

  Hope this helps others who also have this problem, even though my English is not very good. : )

• keyboard & mouse freeze after the mode 'sleep', using Windows Vista 64 home premium

  keyboard & mouse freeze after the mode "sleep", using Windows Vista 64 home premium.  I received once posted this question, an answer of "fix" to a thread that has worked.  Unfortunately, I deleted the thread. I swapped the USB connectors for mouse and keyboard, but that didn't change anything.  Could someone please re - send the wire?  I promise you that I'm deleting it this time.

  Thank you very much

  E-mail address is removed from the privacy *.

  Hi RICH0214,

  Follow these methods.

  Method 1: Follow the steps in the article.

  Device Manager does not display devices that are not connected to the Windows XP-based computer

  http://support.Microsoft.com/kb/315539 (applies to Windows Vista)

  Method 2: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3: Create a new user account.

  Create a user account

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  If the problem is resolved in a new user account, and then follow the article on how to fix a corrupted user account.

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• problem with Internet connection sharing, error: connection ad - hoc has "no internet access" on the cell phone of the customer

  Original title: problem with Internet connection sharing

  my laptop running on Windows Vista Home Premium SP2 (this one has access to the internet by using the dial-up modem and will to act as a sharer of internet connection or as a host) and the client computer runs on Windows 7 Starter

  in a first step, I try internet connection sharing, I've set up an ad hoc network and I just changed my setting modem dial-up on the sharing tab, of course what I change, it of 'Allow an other network users to connect through this computer internet connection' and choose the on Home Networking connection wireless network connection , then my mobile client to connect to a special that I created and portable client connected to the internet via ICS
  then the problem came when I restart my laptop. When I tried to use ICS once again, my customer laptop really takes a long time to connect, he continues saying 'identification' side host and client. and after that "identify" is complete, it says ad - hoc connection, I create has "no network".
  so, I'm a person answer in this forum
  ' Obtain an IP address automatically is the wrong setting on the Ethernet connection. "  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  "DNS server: none.

  I put this on my laptop of the host, and and I put the IP address on my laptop customer in 192.168.0.2 with the same default gateway as my portable computer host IP

  and made some progress in this case, when I try to connect host and the client is no longer to 'identify' phase, immediately connected laptop both but my mobile client can not connect to the internet and displays "No Internet access" on the ad hoc network, I have create

  I tried a lot of things but always completed my mobile client can not connect to the internet and displays the message "no Internet access.

  What makes me confuse is first, I try to share the internet connection everything works like a charm, I set up an ad hoc network, and then change the setting on my modem dial-up so he can share the internet connection, and voila, computer laptop client connected to the internet. I change even not all IP settings

  But why after I restart my PC, this problem comes...

  someone knows how to help me with this problem?

  Hey, Mimbs,

  You can try the similar thread to the next with a possible solution:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/no-Internet-access-in-the-client-machine-when/77312e09-4385-41FA-A420-0c42be58e4e3

  Also for reference:

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows