BenQ scanner 5000 fletbed utility disk n suppot for windows 7 Please suggest

Similar Questions

• How to use the utility disk first aid for hard drive internal el captian

  How to use the utility disk first aid for hard drive internal el captian

  Select the drive and click first aid.

  If something is not repairable because this is the system drive, then you need to start using the recovery partition and run disk utility it.

• Satellite T110 - disk from Toshiba for Windows 7?

  I would like to install just Windows 7 on my Satellite T110 and remove all the Toshiba Software/nag screens. I also have my own copy of ms office that I would like to install.
  All additional drivers of supply will not be a problem.

  Can I source a disk from Toshiba for Windows 7? Someone at - it else here had the experience to do?
  Thank you

  Hey Buddy,

  As far as I know, such a disk is not available but you can download all the drivers and tools on the Web from Toshiba site:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  If you have Windows 7 64 bit, all drivers and tools that you can download on this page! :)

• How to disable the command CHKDSK - Check Disk start up for Windows 7

  I have some problems, when I start my laptop I am prompted with a black screen saying

  

  I found no solutions on how to disable this on my computer, but I want to because after the seconds say 1, its stays for a while... and I've left on during some time, the screen is still asleep when I turn... The page is black... Can someone help me to disable the calendar checking for windows 7? Thank you very much! : D

  Hi PikaBrian,

  Welcome to the Microsoft Answers site!

  To disable automatic disk checking at the start of Windows through registry, go to the following registry key:

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 how to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager

  In the right pane, double click BootExecute.

  The default value of the key is autocheck autochk *

  * means that each drive is checked for consistency. Just add /K:C to the end before *. /K switch will disable autocheck on C: drive at Windows startup. If the final value should look like this:

  / k: C to autocheck autochk *.

  If you want to add more drives, the key should look like this: (by disabling the drives C and D)

  / k: D / k: C autocheck autochk *.

  If you want to restore all default, just replace the key with the default i.e.

  autocheck autochk *.

  You can also follow the link given below and check if it is of no help.

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a8ab415b-4559-45C6-99a4-a54e27e5a836

   

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Moved to laptop Tungsten T5, need a software disk or download for windows Vista, HELP PLEASE

  Bought a new laptop, old lost disk, was for windows XP, new laptop has windows vista. Need to hotsync my Palm of window w/vista computer laptop purchased the update for Microsoft windows and excel. But the operating system is vista. Need to drive or download to synchronize my palm tungsten T5 to vista. Cannot find compatible download tried V.6, 4 and 1. Doesn't sync gives error. Please help need my Palm as soon as POSSIBLE to the work. Please help, can email me at [email protected] or post on this Web site.  I tried live help, but they do not pick up and keeps giving me an error. I have a wireless internet. 2nd question do I need be connected to an internet connection by cable or wireless OK, my computer works well with wireless so far. Would appreciate any help you can give me. Thank you so much.

  I was able to know that I have a 64 bit. Any help please. I was check other blogs and will hopefully find help, but in the meantime if anyone could help I would appreciate it.

• What should I do to move from Vista, which I have no disk or key for Windows 7?

  I bought my computer with Vista already installed without disks or product keys to talk about.  When I get the product key 'system', provided that it is authenticated had "OEM" in a part of the key.  It's true that I can't buy a Windows 7 upgrade version if it is an OEM of Vista version?  Should what version I?  He is currently 32-bit.  I choose either 32 or 64 bits for the new os?

  If you have Vista, you can buy the Windows 7 upgrade version, it does not matter if Vista is OEM.

  You can buy Windows 7 here:

  http://www.microsoftstore.com/store/msstore/cat/CategoryID.44066700

  How to upgrade:

  If you have Vista:

  Update: http://windows.microsoft.com/en-us/windows7/help/upgrading-from-windows-vista-to-windows-7

  Custom installation: http://windows.microsoft.com/en-US/windows7/help/upgrading-from-windows-vista-to-windows-7-custom

  If you are running Windows Vista , in some cases you can proceed directly to Windows 7, and in other cases, you must perform a custom installation. The following table shows what editions of Windows Vista can be upgraded to Windows 7.

  Windows Vista Home Basic	Windows 7 Home Premium, Windows 7 Ultimate
  Windows Vista Edition Home Premium	Windows 7 Home Premium, Windows 7 Ultimate
  Windows Vista Business	Windows 7 Professional, Windows 7 Ultimate
  Windows Vista Ultimate Edition	Windows 7 Ultimate

  For more information, see upgrading from Windows Vista to Windows 7 . (http://windows.microsoft.com/upgrade-windows-vista )
  You can't go from 32 bit to 64 bit, a clean install is required. If you have any questions about the upgrade from 32 bit to 64 bit or vice versa, please see this FAQ: http://windows.microsoft.com/en-us/windows7/32-bit-and-64-bit-Windows-frequently-asked-questions
  If you have any general questions about reinstalling Windows , please see this site:
  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows

• 127 GB of disk space required for Windows XP?

  I use the copy of XP comes with my computer 10 years ago.  I upgraded to SP 3.  XP is now 127 GB of my 142 GB disck drive.  I think it should be less than 70 GB.  How can I reduce the space occupied by Windows?

  Thank you!

  The brief flash was probably because you run msizap by double-clicking to open a command prompt window instead and it works there.

  This is probably the best at this time for you to take the computer to a local store.  I suggest does not go to a place geeksquad or type BigBoxStoreUSA, but you probably right that who take you to reinstall Windows.  Don't forget to tell them to back up your data files (photos, documents, music, etc.) first.

  Unless the Office was preinstalled on the computer when you bought it (and the store chooses to use the method of 'back to the conditions of the factory'), you must reinstall Office.  You also need to reinstall other applications that are now on the computer.  You need original installation media and product keys.  Ask the shop to extract the product keys for your various applications before reinstalling Windows.

  Good luck.

• How can I get the amount of free disk space using the space using windows 7 Please share example using GetDiskSpace

  How can I get the amount of disk space by using windows 7 Please share example using GetDiskSpace I already studied http://digital.ni.com/public.nsf/allkb/9958B8E473C4EF1786256BBC0053B64F

  Reading your question a little more in detail, I doubt if you are using the Win32 GetDiskFreeSpace API function (including my previous post is the solution) of the function GetDiskSpace from the Toolbox of the programmer.

  With respect to the other, it works even with capacity greater than 2 GB disks, but you must use the appropriate formatting code to display the returned value. I updated my example to display the total of free space in the debug output window and added a comparison with the value of 3 GB using UInt64TypeCompareUInt box to tools programming interface.

• Where can I find the disk clean up on windows 8?

  Where can I find the disk clean up on windows 8, please?

  Thank you very much.

  Open your Start menu and tap it that the word own and it will appear in your search results (similar to Windows 7 where you can search by typing in the start menu).

• Utility disk and MS DOS

  One of my friends asked me to try to format a 8 TB new drive he bought. He needs to FAT32 for his playstation and I think it is either running leopard or snow leopard. I've got El capitan.

  What he did:

  Initially the ability to format with MS-DOS was dimmed, he partitioned the drive into partitions of 7.9 TB and 0.1 and the ability to format to MS DOS became available, he went ahead and disk utility reported that have successfully completed. I suspect that he does not check readers reported sizes in the finder at this stage, but when he turned on his PC that reported the largest partition 1.68 TB.

  It has reconnected to the Mac and re-partioned into partitions of 2 x 4TB with much the same result.

  What I did:

  When I plugged the drive, Get info reported volumes 2 x 1.8 TB but made each utility disk volume count volumes of 2 x 4TB with 2.2 TB of space in use. I then wiped the drive and created a 8TB Mac OS volume that has been reported correctly in the finder and in disk utility. The ability to format in the MS-DOS was available on my Mac even if it was divided into a single volume of 8 TB, I am gone ahead and utility disk has reported formatting was successful but get info reported a single figure of 1.8 to.

  I tried since a 7.8/divided 0.2 TB and ended with only a volume of 1.2 to get info and 6.6 TB of space used of the CT 7.8 according to disk utility.

  The thing is every book that I try again with MS DOS I seem to get a smaller usable volume.

  I'm not familiar with the help of MS-DOS formatted, but we had problems when it restructured a 2 GB usb key that we sometimes in the past, although I suspect that he reformatted his PC. So I don't know if there is a problem with a 8 TB disk, disk utility or even its PC.

  FWIW, Microsoft has imposed a limit of 32 GB for FAT/FAT32 partitions, but it is possible to create partitions of 2 TB. I suspect that's what you see.

  You should be able to create 4 partitions of 2 TB ExFAT.

• Utility disk and moving Qosmio X 500 record low space drice C

  This can be a pretty long post because I try to explain my problem... Please forgive.

  I got my X 500 over three months now.
  It took a little while before only the awake folder migration utility I didn't know that it is there after I had done a limited copy of the records in front of my old Qosmio F20. After he woke up and I was able to transfer files/folders through it allows plenty of room for the "tiny" - I feel, 60 GB SSD C drive.

  I get a message to come sometimes, when I boot, the file migration utility has a setting for me. If I open the utility it shows no file in the 'C' drive area and already transferred files [first use it] in the side right for him had ' drive. Text at the bottom of the utility said something like "If you have done some manual transfers, so it cannot do anything"... something in the lines - sorry for not being clear on this.

  I recently installed other programs and tried every time to do an install custom files [x 86] on the D drive in the program folder. However, drive C is now showing a to 5.58 59.2 GB disk space.

  Check copies of records? I thought that for the programs I have installed I find a lot of folders/files in these folders, so take plenty of program.

  What is the best way to free up space on the drive "C" Please?

  I have to manually copy the data contained in the files [not only a 'name'... IE; [AVID... folder but perhaps also in drive C program files (x 86) folder] to the same name of folders on drive D?

  If I did, the programs would work properly or there are problems in the program being located?

  When the utility first activated [se] I thought ' great... transfer of all data from my old X 500 will be easy ', but it doesn't seem to be the case. I expect that any new program installed would be are automatically copied into drive D. I'm a bit paranoid about insufficient space on the C drive.

  Help would be appreciated.

  To be honest I don t understand why you use any file migration utility only to copy the data from one HARD drive to another.

  In my opinion, you simply copy the data to another partition. If you need different folders, then you can create it manually.

  So, I recommend always using the C partition for system only! The D partition can be used for other data like pictures, movies, MP3s, PDFs etc.

  > What is the best way to free up space on the drive "C" Please?
  Well, transfer the data from C to D, but note; You cannot move installed programs.
  This means that if you install an application on C and if you move this to D then this software is not works.
  In this case, you need to install once again on D.

• El Capitan utility disk first aid fails - unable to unmount the volume for repair

  Question: Given the following error with Disk Utility first aid and success with diskutil check volume, I should consider my drive damaged or volume?

  After a crash of the system on my Mac mini (end 2012) running that OS X El Capitan 10.11.3 has experienced a kernel panic induced by the adapter USB Wi - Fi, I dutifully ran first aid utility disk on each volume on the disk, in order to ensure the integrity of system files.

  What I feel with disk utility (GUI) first aid:

  First aid process has failed. If it is possible to backup the data on this volume.  Click OK to continue.

  Check the storage system

  Volume control

  disk4s2: search Volume headers

  disk4s2: search for disc labels

  12EB36F7-A2FD-450B-AB5A-DA2D430BA3B2 group of logical volumes on 1 device

  disk4s2: search the Volume metadata

  Logical volume group has a Volume of metadata 24 MB with double redundancy

  Start the analysis of the metadata for a valid checkpoint

  Load and check the Segment headers

  Load and check the payload control point

  Load and check the Transaction Segment

  Incorporate 0 most recent checkpoint operations of no

  Load and check the virtual address Table

  Load and check the use Table Segment

  Load and check the Metadata Superblock

  Load and check the volume logic B-trees

  Logical Volume group contains 1 Logical Volume

  Load and check 3D8DB35F-FA41-4A58-BA33-84A2C08FEE93

  Load and check 1CD6382C-9DF5-44E6-8C66-1CDC3DE5DB8A

  Load and check the summary of Freespace

  Load and check the accounting of block

  Load and check out virtual addresses live

  New control point of transaction commit is valid

  Load and check the Segment cleaning

  The 12EB36F7-A2FD-450B-AB5A-DA2D430BA3B2 volume seems to be OK

  Checking storage system exit code is 0

  Updated support for the volume partition that

  Impossible to disassemble for repair volume

  Operation failed...

  (underlining)

  Additional information: I didn't have any problems with this disk volume. I use it only as a Time Machine backup destination. It is an encrypted volume OS X Extended (respect for case-sensitive). My concern involves only disk utility complaint that its "first aid process has failed."

  After reading the complaints in other forums that utility disk on El Capitan has been "dumbed down" and can not perform many of the functions that the utility of the same name used to be able to perform in previous versions of Mac OS (complaints, I can't confirm because I'm relatively new to MacOS - although extremely in computing with Windows, UNIX and Linux) (, so I didn't get to use disk utility a lot, before El Capitan), I decided to do the same "check the volume" that I knew first aid was trying to perform with the diskutil command-line app.  Guess what? No error!:

  What I have experienced with command-line diskutil:

  sudo diskutil verifyvolume disk9

  Audit file system began on disk9 6TBMacOS_1_Archive

  Check the storage system

  Volume control

  disk4s2: search Volume headers

  disk4s2: search for disc labels

  12EB36F7-A2FD-450B-AB5A-DA2D430BA3B2 group of logical volumes on 1 device

  disk4s2: search the Volume metadata

  Logical volume group has a Volume of metadata 24 MB with double redundancy

  Start the analysis of the metadata for a valid checkpoint

  Load and check the Segment headers

  Load and check the payload control point

  Load and check the Transaction Segment

  Incorporate 0 most recent checkpoint operations of no

  Load and check the virtual address Table

  Load and check the use Table Segment

  Load and check the Metadata Superblock

  Load and check the volume logic B-trees

  Logical Volume group contains 1 Logical Volume

  Load and check 3D8DB35F-FA41-4A58-BA33-84A2C08FEE93

  Load and check 1CD6382C-9DF5-44E6-8C66-1CDC3DE5DB8A

  Load and check the summary of Freespace

  Load and check the accounting of block

  Load and check out virtual addresses live

  New control point of transaction commit is valid

  Load and check the Segment cleaning

  The 12EB36F7-A2FD-450B-AB5A-DA2D430BA3B2 volume seems to be OK

  Checking storage system exit code is 0

  Check the file system

  Using the live mode

  Perform direct verification

  Logged more HFS volume control

  Detected a case-sensitive volume

  Checking extents overflow file

  Check the extended attribute file

  Checking volume bitmap

  The 6TBMacOS_1_Archive volume seems to be OK

  File system check exit code is 0

  Finished on disk9 6TBMacOS_1_Archive file system check

  I will finish success of diskutil verifyvolume that my disk volume is not serious and that Disk Utility first aid simply does not correctly?

  Thank you!

  -IlDavo-

  I think you might be able to do a repair of first aid, after you have disassembled the drive first:

  1. Run OS X by an external device (ex: USB mode, or external hard drive or disk target from another Mac)
  2. Launch the Terminal and run the following command umount f /Volumes/ (ex: umount f/Volumes/Macintosh\ HD)
  3. Then run disk utility first aid.

  I had this problem on a Macbook Air, I tried to recreate the image to work, so I didn't need to get anything off the drive. I tried to format the drive and reinstall OS X. So I don't know if first aid work after disassembly, but it worked without a doubt after that I did the first two steps above and then deleted from the disk. Not sure if this will help, but worth a try, I guess.

• I can see my Seagate backup more player in the utility disk and report system, but not in the Finder. Can someone please?

  I have a Mac Book Pro (mid-2012) which ran OS 10.9 Mavericks, which I upgraded to El Captain a few days ago. My Seagate external backup more BK 1 TB hard drive was working fine (reading, writing, all things were very good) with the Mavericks. After upgrade, he once showed in the Finder and after a reboot, it stopped in the Finder. I can see utility disk and the system of report but cannot do much from here, as you can see at the bottom of screen captures.

  

  

  Backup external drive more BK is formatted in NTFS and I NTFS for Mac OS X driver/application on Mac. When I plug the same backup external drive more BK in a Windows machine it works as well as *. I understand what happened with her. This external drive is complete with tons of very important and useful data. Can someone please help with this?

  After the upgrade to El Capitan, have you installed the version 14 of Paragon? To what level, you would need and this for download, see this .

• 4630 won't recognize scanner - printer and utility connect properly

  4630 won't recognize scanner - printer and utility connect correctly.

  Downloaded the software for Mac OS 10.10 altest, but he still does not see the scanner.

  Help, please!

  I uninstalled and reinstalled and it works again.

  Thank you

• BenQ Scanner Flatbed22 s z w 3300 u driver to work with Windows7 Wanted

  Dear Helper,

  Hope this finds you well and in good spirits. I need to "driver" to work with Windows7 for my BenQ Scanner Flatbed22 s z w 3300 u. can help you find the same thing and force.

  Sincere greetings,

  Abgrall

  Hello

  As OEM BenQ is responsible for the good operation of the scanner and their
  drivers provided. Check with the support of BenQ, their books online and
  drivers and ask in their forums (if any).

  BenQ
  http://www.BenQ.com/

  Windows 7 Compatibility Center - shows the S2W 3300U Barcode Scanner like
  not compatible with Windows 7 32 or 64-bit.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/details.aspx?type=hardware&p=BenQ%20S2W-3300U%20Barcode%20Scanner&v=BenQ&UID=&l=en-us&c=printers%20%26%20Scanners&SC=scanners

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">