BEVP41 problems to a 200 Fortigate vpn tunnel has

Similar Questions

• Problem passing traffic through the VPN tunnel

  With well over 150 VPN lan-to-lan tunnels configured, I can usually get tunnels upward. However, this one is stumping me, unless the ISP is to give false information. Using a router Cisco 871 on-site a Cisco 3005 concentrator in my data center, I have set up my tunnel. The tunnel will go up but won't traffic. I am sure that the configurations on both devices are correct because I use a lot of "cut-and - paste." So, the only question seems to be the modem/router provided by your ISP. Usually, when this happens, the problem is with NAT enabled on their equipment. According to them, that it is not enabled on their NAT router. Where can else I check? Any ideas?

  Check access lists and a static route

  Try these links: >

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_guide_chapter09186a00803ee1e4.html#wp999593

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a00800949c5.shtml

• ASA Cisco IPSEC VPN tunnel has not managed the traffic

  Hi guys

  I am trying to set up a new connection IPSEC VPN between a Cisco ASA 5520 (verion 8.4 (4)) and Checkpoint Firewall. I managed to establish the phases IKE and IPSEC and I can see the tunnel is UP. But I can't see any traffic through the tunnel. I checked the cryptomap both ends and try to test with a contionuous ping from within the network of the SAA.

  I made a screenshot of ICMP packets but cannot see in ASA. I welcomed the icmp inside ASA interface.

  I did a package tracer and it ends with a fall of vpn - filter the packets. But can not see any configured filters...

  Your help is very appreciated...

  Thank you

  You probably need to add nat negate statements:-something like.

  object-group network OBJ-LOCAL
  Network 10.155.176.0 255.255.255.0
  object-group network OBJ / remote
  object-network 192.168.101.0 255.255.255.0
  NAT static OBJ-LOCALOBJ-LOCAL source destination (indoor, outdoor) static OBJ-REMOTE OBJ-REMOTE-no-proxy-arp

  You are running 8.4 nat 0 has been amortized

• VPN tunnel action

  HELO all

  I'm in this situation:

  I have a tunnel VPN setup and running on a router 1800.
  Our customer wants a tunnel of intervention similar to this (with other peer IP of course).

  When the main vpn tunnel has dropped the other will take over.

  My question: can I put a second peer who will take over when the first falls:

  Nome-240 crypto map ipsec-isakmp crypto
  VPN CLIENT description
  defined by peer 201.94.151.141
  defined by peer 201.94.151.142
  86400 seconds, life of security association set
  the value of the transform-set 3des-sha
  match the address vpn_intlfcstone

  or

  I have to make another card encryption as follows (using the same access list)?

  Nome- 240 crypto map ipsec-isakmp crypto
  VPN CLIENT description
   defined by peer 201.94.151.141 -(main post)
  86400 seconds, life of security association set
  the value of the transform-set 3des-sha
  address for correspondence vpn_intlfcstone

  Nome- 250 crypto map ipsec-isakmp crypto
  VPN CLIENT description
   defined by peer 201.94.151.142 -(second peer)
  86400 seconds, life of security association set
  the value of the transform-set 3des-sha
  address for correspondence vpn_intlfcstone

  The two Tunnel VPN must be on the same router (unfortunately) (1800).

  Hello edilson.silva1,

  You can configure a second IP for backup VPN peer.

  http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_vpnav/configuration/XE-3s/asr1000/sec-VPN-availability-XE-3s-asr1000-book/sec-IPSec-pref-peer.html#GUID-527C42AE-44EC-4178-BBC3-B65189329B03

  Creating a different sequence in the encryption for the same traffic map will generate a problem that overlap.

• ASA base S2S VPN, Tunnel establishes only when interesting traffic hits to end distance

  Dear all,

  I need your help to solve the problem mentioned below.

  VPN tunnel established between the unit two ASA.   A DEVICE and device B

  (1) if interesting traffic initiates a LAN device. traffic ACL hits. TUNEL is not coming

  (2) if interesting traffic initiates B LAN device. Tunnel will establish all the works of serivces

  (3) after the Tunnel device establishmnet B. We forced to tunnel down at both ends. Interesting again traffic initiates device a surpringly tunnel

  will go up.   After 2 or 3 days (after life expire 86400 seconds) initiated traffic of device A, tunnel will not esatblish.

  (it comes to rescue link: interesting won't be there all the time.)

  checked all parametrs, everthing seems fine. Here are the logs of attached but not more informative debugging on the balls. Please suggest.

  February 2, 2010 13:23:17: % ASA-7-713236: IP = 81.145.x.x, IKE_DECODE new SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 496

  February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:23: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:25: % ASA-7-715065: IP = 81.x.x.x, history of mistake IKE MM Initiator WSF (struct & 0x1abb1e10) , : MM_DONE, EV_ERROR--> MM_WAIT_MSG2, EV_RETRY--> MM_WAIT_MSG2, EV_TIMEOUT--> MM_WAIT_MSG2 NullEvent--> MM_SND_MSG1, EV_SND_MSG--> MM_SND_MSG1, EV_START_TMR--> MM_SND_MSG1, EV_RESEND_MSG--> MM_WAIT_MSG2, EV_RETRY

  February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, IKE SA MM:56f95c85 ending: flags 0 x 01000022, refcnt 0, tuncnt 0

  February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, sending clear/delete with the message of reason

  February 2, 2010 13:23:25: % ASA-3-713902: IP = 81.x.x.x, counterpart of drop table counterpart, didn't match!

  February 2, 2010 13:23:25: % ASA-4-713903: IP = 81.x.x.x, error: cannot delete PeerTblEntry

  Hi, I have a similar problem a long time ago. You can choose which set up the tunnel in your crypto card:

  card crypto bidirectional IPsec_map 1 set-type of connection

  I hope that it might help to solve your problem. Kind regards.

• VPN Tunnel problem. external interface has private IP

  Hi all

  I don't know if it is wired or not!

  When our ISP provide us an Internet connection our real IP is configured on the ethernet interface, while the serial interfaces have a private IP address.

  The problem here is when I'm trying to configure a VPN tunnel to another router.

  Anything in the configuration is smooth, except for the part where I put the serial interface is my outside.

  The tunnel is still low coz the IP address will be my private (serial interface) during the configuration on the router counterpart is my public IP address.

  So I am woundering is there a way I can force the VPN tunnel to take the IP address configured on the side LAN? Or any other work around?

  Building configuration...

  Current configuration: 2372 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  boot-start-marker

  start the flash c1841-advsecurityk9 - mz.124 - 23.bin system

  boot-end-marker

  !

  property intellectual auth-proxy max-nodata-& 3

  property intellectual admission max-nodata-& 3

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 2

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  isakmp encryption key * address 144.254.x.y

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  map SDM_CMAP_1 1 ipsec-isakmp crypto

  Description Tunnel to144.254.x.y

  the value of 144.254.x.y peer

  game of transformation-ESP-3DES-SHA

  match address VPN_Traffic

  !

  !

  !

  interface FastEthernet0/0

  address IP 10.55.218.1 255.255.255.0 secondary (My internal subnet)

  IP address 196.219.a.b 255.255.255.224 (my public IP)

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  No keepalive

  !

  interface FastEthernet0/1

  no ip address

  automatic duplex

  automatic speed

  !

  interface Serial0/0/0

  no ip address

  frame relay IETF encapsulation

  frame-relay lmi-type q933a

  !

  point-to-point interface Serial0/0/0.16

  IP 172.16.133.2 255.255.255.252

  NAT outside IP

  IP virtual-reassembly

  SNMP trap-the link status

  dlci 16 frame relay interface

  map SDM_CMAP_1 crypto

  !

  interface Serial0/0/1

  no ip address

  frame relay IETF encapsulation

  ignore the dcd

  frame-relay lmi-type q933a

  !

  point-to-point interface Serial0/0/1.16

  IP 172.16.134.2 255.255.255.252

  NAT outside IP

  IP virtual-reassembly

  SNMP trap-the link status

  dlci 16 frame relay interface

  map SDM_CMAP_1 crypto

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 Serial0/0/1.16

  IP route 0.0.0.0 0.0.0.0 Serial0/0/0.16

  !

  VPN_Traffic extended IP access list

  Note Protect traffic Local to any Destination subnet

  Remark SDM_ACL = 4 category

  IP 10.55.218.0 allow 0.0.0.255 any

  !

  Scheduler allocate 20000 1000

  end

  This should do the trick.

  map SDM_CMAP_1 crypto local-address FastEthernet0/0

  See you soon

• Connectivity on the VPN tunnel problem.

  Hello

  I have a site to tunnel between the PIX506 and Cisco VPN 3000 Concentrator. I'll be spending it again ASA5510, so the tunnel will be established between the ASA and PIX. After inistial tests, I found only one box of remote network (time clock lol) is down by connectivity while tunnel between Pix and ASA (works fine with the hub). All traffic is allowed through the VPN tunnel built on SAA is? I understand it should be as long as the tunnel is running, correct? (Note: the remote clock uses ports TCP 8888 and 8889 to communicate with the server)

  Thank you

  If there is no filter, again all traffic should be allowed.

  You need not choose L2TP connection is pure IPsec.

  If you wish, you can post your configurations to check them out (you can remove sensitive information)

  Federico.

• After the VPN Tunnel access problem is in place.

  Could someone please take a look at this config and tell me why, once I have the VPN tunnel to the top, I can't access all hosts on the 192.168.41.0 network? (The x are inserted for privacy). Thank you.

  Try...

  ISAKMP nat-traversal

• Problems with basic setup and split tunneling VPN

  I created a SSL VPN in an ASA CISCO ASDM 6.6 8.6 running.
  IM able to connect to the VPN and reach all the devices with the LAN but I am not able to browse the web. When I activate the tunnel split Im able to browse the web, but then Im not able to reach any internal device.
  Here is part of the show's run:

  network of the RedInterna object
  150.211.101.0 subnet 255.255.255.0
  Description Red Interna
  network of the NETWORK_OBJ_10.4.1.0_28 object
  subnet 10.4.1.0 255.255.255.240
  inside_access_in list extended access permitted ip object RedInterna all
  Standard access list VPN_INTERNET allow 150.211.101.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  management of MTU 1500
  local pool VPN_POOL 10.4.1.1 - 10.4.1.14 255.255.255.240 IP mask
  failover
  secondary failover lan unit
  failover lan interface GigabitEthernet0 fail-1/2
  key changeover *.
  failover interface ip fail-1 10.3.1.21 255.255.255.252 watch 10.3.1.22
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 66114.bin
  enable ASDM history
  ARP timeout 14400
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 non-proxy-arp-search to itinerary
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
  Route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
  Route inside 150.211.0.0 255.255.0.0 10.1.1.78 1

  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_VPN_ group strategy
  attributes of Group Policy GroupPolicy_VPN_
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  dominio.com.MX value by default-field
  type tunnel-group VPN_ remote access
  attributes global-tunnel-group VPN_
  address VPN_POOL pool
  Group Policy - by default-GroupPolicy_VPN_
  tunnel-group VPN_ webvpn-attributes
  enable VPN_ group-alias
  !

  I m don't know if Im missing a few small details or Setup. Any help will be much appreciated.
  Thank you!!!

  Hello

  When you use full VPN Tunnel (which is the default setting), you will have a number of things that you need to configure on the SAA.

  First, the ASA by default will not allow traffic to enter via an interface and then exit through the same interface. It is essentially, what happens when the customer VPN traffic comes to the ASA and then heads on the Internet.  In your case the traffic goes through the 'outside' and leaves via the 'outside' interface.

  You will need this command

  permit same-security-traffic intra-interface

  You can check if their licence at the moment with the command

  See the race same-security-traffic

  Second, VPN users will need to have the NAT configuration like all users LAN behind the ASA real. So you basically configure dynamic PAT for 'outside' to 'outside' traffic

  You can get there with the following configuration

  network of the VPN-PAT object

  subnet 10.4.1.0 255.255.255.240

  dynamic NAT interface (outdoors, outdoor)

  I suppose it should do for you to be able to connect to the Internet and the LAN when the VPN is active.

  Hope this helps

  Let me know how it goes.

  -Jouni

• Cisco ASA 5515 two asa firewall ipsec vpn tunnel is not coming

  HelloW everyone.

  I configured ipsec vpn tunnel between Singapore and Malaysia with asa firewall.

  but the vpn does not come to the top. can someone tell me what can be the root cause?

  Here is the configuration of twa asa: (I changed the ip address all the)

  Singapore:

  See the race
  ASA 2.0000 Version 4
  !
  ASA5515-SSG520M hostname
  activate the encrypted password of PVSASRJovmamnVkD
  names of
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 192.168.15.4 255.255.255.0
  !
  interface GigabitEthernet0/1
  nameif DMZ
  security-level 50
  IP 192.168.5.3 255.255.255.0
  !
  interface GigabitEthernet0/2
  nameif outside
  security-level 0
  IP 160.83.172.8 255.255.255.224
  <--- more="" ---="">
                
  !
  <--- more="" ---="">
                
  interface GigabitEthernet0/3
  <--- more="" ---="">
                
  Shutdown
  <--- more="" ---="">
                
  No nameif
  <--- more="" ---="">
                
  no level of security
  <--- more="" ---="">
                
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  nameif test
  security-level 100
  IP 192.168.168.219 255.255.255.0
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  connection of the banner ^ C please disconnect if you are unauthorized access ^ C
  connection of the banner please disconnect if you are unauthorized access
  boot system Disk0: / asa922-4-smp - k8.bin
  passive FTP mode
  network of the SG object
  <--- more="" ---="">
                
  192.168.15.0 subnet 255.255.255.0
  network of the MK object
  192.168.6.0 subnet 255.255.255.0
  service of the TCP_5938 object
  Service tcp destination eq 5938
  Team Viewer description
  service tcp_3306 object
  Service tcp destination eq 3306
  service tcp_465 object
  tcp destination eq 465 service
  service tcp_587 object
  Service tcp destination eq 587
  service tcp_995 object
  tcp destination eq 995 service
  service of the TCP_9000 object
  tcp destination eq 9000 service
  network of the Inside_host object
  Home 192.168.15.202
  service tcp_1111 object
  Service tcp destination eq 1111
  service tcp_7878 object
  Service tcp destination eq 7878
  service tcp_5060 object
  SIP, service tcp destination eq
  <--- more="" ---="">
                
  service tcp_5080 object
  Service tcp destination eq 5080
  network of the NETWORK_OBJ_192.168.15.0_24 object
  192.168.15.0 subnet 255.255.255.0
  inside_access_in list extended access allowed object SG ip everything
  OUTSIDE_IN list extended access permit tcp any newspaper EQ 9000 Inside_host object
  access extensive list ip 192.168.15.0 outside_cryptomap allow 255.255.255.0 object MK
  pager lines 24
  Enable logging
  timestamp of the record
  exploitation forest-size of the buffer of 30000
  debug logging in buffered memory
  recording of debug trap
  debugging in the history record
  asdm of logging of information
  host test 192.168.168.231 record
  host test 192.168.168.203 record
  Within 1500 MTU
  MTU 1500 DMZ
  Outside 1500 MTU
  test MTU 1500
  management of MTU 1500
  no failover
  <--- more="" ---="">
                
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 7221.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source SG SG static destination MK MK non-proxy-arp-search to itinerary
  !
  network of the SG object
  NAT dynamic interface (indoor, outdoor)
  network of the Inside_host object
  NAT (inside, outside) interface static 9000 9000 tcp service
  inside_access_in access to the interface inside group
  Access-group OUTSIDE_IN in interface outside
  Route outside 0.0.0.0 0.0.0.0 160.83.172.x 1
  Route inside 10.0.1.0 255.255.255.0 192.168.15.199 1
  Route inside 10.0.2.0 255.255.255.0 192.168.15.199 1
  Route inside 10.0.11.0 255.255.255.0 192.168.15.199 1
  Route inside 10.1.0.0 255.255.0.0 192.168.15.199 1
  Route inside 10.8.0.0 255.255.0.0 192.168.15.199 1
  Route inside 10.104.0.0 255.255.0.0 192.168.15.199 1
  Route inside 192.168.8.0 255.255.255.0 192.168.15.199 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  <--- more="" ---="">
                
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  Enable http server

  Community trap SNMP-server host test 192.168.168.231 *.
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps syslog
  Crypto ipsec transform-set ikev1 VPN-TRANSFORM esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  <--- more="" ---="">
                
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  <--- more="" ---="">
                
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  crypto CRYPTO - map 2 map corresponds to the address outside_cryptomap
  card crypto CRYPTO-map 2 set peer 103.246.3.54
  card crypto CRYPTO-map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto CRYPTO-map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  CRYPTO-card interface card crypto outside
  trustpool crypto ca policy
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400

  Console timeout 0
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  internal GroupPolicy1 group strategy
  attributes of Group Policy GroupPolicy1
  Ikev1 VPN-tunnel-Protocol
  username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
  username gmsadmin password HS/VyK0jtJ/PANQT encrypted privilege 15
  tunnel-group 143.216.30.7 type ipsec-l2l
  tunnel-group 143.216.30.7 General-attributes
  Group Policy - by default-GroupPolicy1
  <--- more="" ---="">
                
  IPSec-attributes tunnel-group 143.216.30.7
  IKEv1 pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  Overall description
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  <--- more="" ---="">
                
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:ccce9a600b491c8db30143590825c01d
  : end

  Malaysia:

  :
  ASA 2.0000 Version 4
  !
  hostname ASA5515-SSG5-MK
  activate the encrypted password of PVSASRJovmamnVkD
  names of
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 192.168.6.70 255.255.255.0
  !
  interface GigabitEthernet0/1
  nameif DMZ
  security-level 50
  IP 192.168.12.2 255.255.255.0
  !
  interface GigabitEthernet0/2
  nameif outside
  security-level 0
  IP 143.216.30.7 255.255.255.248
  <--- more="" ---="">
                
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  nameif test
  security-level 100
  IP 192.168.168.218 255.255.255.0
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  <--- more="" ---="">
                
  Interface Port - Channel 1
  No nameif
  no level of security
  IP 1.1.1.1 255.255.255.0
  !
  boot system Disk0: / asa922-4-smp - k8.bin
  passive FTP mode
  clock timezone GMT + 8 8
  network of the SG object
  192.168.15.0 subnet 255.255.255.0
  network of the MK object
  192.168.6.0 subnet 255.255.255.0
  service of the TCP_5938 object
  Service tcp destination eq 5938
  Team Viewer description
  service tcp_3306 object
  Service tcp destination eq 3306
  service tcp_465 object
  tcp destination eq 465 service
  service tcp_587 object
  Service tcp destination eq 587
  service tcp_995 object
  tcp destination eq 995 service
  service of the TCP_9000 object
  <--- more="" ---="">
                
  tcp destination eq 9000 service
  network of the Inside_host object
  Home 192.168.6.23
  service tcp_1111 object
  Service tcp destination eq 1111
  service tcp_7878 object
  Service tcp destination eq 7878
  service tcp_5060 object
  SIP, service tcp destination eq
  service tcp_5080 object
  Service tcp destination eq 5080
  network of the NETWORK_OBJ_192.168.2.0_24 object
  192.168.6.0 subnet 255.255.255.0
  inside_access_in list extended access allowed object SG ip everything
  VPN-INTERESTING-TRAFFIC extended access list permit ip object MK SG
  OUTSIDE_IN list extended access permit tcp any newspaper EQ 9000 Inside_host object
  outside_cryptomap to access extended list ip 192.168.6.0 allow 255.255.255.0 object SG
  pager lines 24
  Enable logging
  timestamp of the record
  exploitation forest-size of the buffer of 30000
  debug logging in buffered memory
  recording of debug trap
  asdm of logging of information
  <--- more="" ---="">
                
  host test 192.168.168.231 record
  host test 192.168.168.203 record
  Within 1500 MTU
  MTU 1500 DMZ
  Outside 1500 MTU
  test MTU 1500
  management of MTU 1500
  reverse IP check management interface path
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 7221.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source MK MK static destination SG SG route no-proxy-arp-search
  NAT (inside, outside) static source NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 static destination SG SG route no-proxy-arp-search
  !
  network of the MK object
  NAT dynamic interface (indoor, outdoor)
  network of the Inside_host object
  NAT (inside, outside) interface static 9000 9000 tcp service
  inside_access_in access to the interface inside group
  Access-group OUTSIDE_IN in interface outside
  Route outside 0.0.0.0 0.0.0.0 143.216.30.x 1
  <--- more="" ---="">
                
  Route inside 10.2.0.0 255.255.0.0 192.168.6.200 1
  Route inside 10.6.0.0 255.255.0.0 192.168.6.200 1
  Route inside 192.168.254.0 255.255.255.0 192.168.6.200 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication http LOCAL console
  the ssh LOCAL console AAA authentication
  Enable http server

  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 VPN-TRANSFORM esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  <--- more="" ---="">
                
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  <--- more="" ---="">
                
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  crypto CRYPTO - map 2 map corresponds to the address outside_cryptomap
  card crypto CRYPTO-map 2 set peer 160.83.172.8
  card crypto CRYPTO-map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  CRYPTO-card interface card crypto outside
  trustpool crypto ca policy
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  SSH timeout 60
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  attributes of Group Policy DfltGrpPolicy
  Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
  internal GroupPolicy1 group strategy
  attributes of Group Policy GroupPolicy1
  Ikev1 VPN-tunnel-Protocol
  username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
  username gmsadmin password HS/VyK0jtJ/PANQT encrypted privilege 15
  <--- more="" ---="">
                
  tunnel-group MK SG type ipsec-l2l
  IPSec-attributes tunnel-group MK-to-SG
  IKEv1 pre-shared-key *.
  tunnel-group 160.83.172.8 type ipsec-l2l
  tunnel-group 160.83.172.8 General-attributes
  Group Policy - by default-GroupPolicy1
  IPSec-attributes tunnel-group 160.83.172.8
  IKEv1 pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  <--- more="" ---="">
                
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
  : end

  Good news, that VPN has been implemented!

  According to the ping problem, my suggestion is to check, if some type of firewall based on host computers on both sides block ICMP requests.

  Anyway, you can still use the capture of packets on the inside of the interfaces of the two ASAs, to check if the ICMP traffic is to reach the ASA.

  In addition, you can try to enable ICMP inspection:

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  inspect the icmp error

• 3500 x vpn tunnel

  I need to establish a vpn connection between my office and a computer over the internet, allowing access to the internal of the outside lan. I have a problem with my router and I am looking for a new.

  Can I use x 3500 to establish a pptp vpn tunnel or it can work only as vpn passthrough?

  This modem/router supports VPN passthrough for IPSec, PPTP and L2TP only. Try VPN Linksys Gigabit routers like the series of the LRT.

• RV042 VPN tunnel with Samsung Ubigate ibg2600 need help

  Hi all, ok before I completely remove all of my hair, I thought stop by here and ask the volume for you all with the hope that someone can track down the problem.

  In short I am configuring a 'Gateway to gateway' vpn tunnel between two sites, I don't have access to the config of the router from Samsung, but the ISPS making sure that they followed my setup - watching newspapers RV042, I don't however see the reason for the failure - im no expert vpn...

  Sorry if the log file turns on a bit, I didn't know where the beginning and the end was stupid I know... any advice would be greatly welcomed lol.

  System log
  Current time: Fri Sep 2 03:37:52 2009 all THE Log Log Log Log VPN Firewall Access system
   
  Time
  Type of event Message
  2 sep 03:36:01 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba08
  2 sep 03:36:01 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = c664c1ca
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
  2 sep 03:36:02 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
  2 sep 03:36:02 2009 VPN received log delete SA payload: ISAKMP State #627 removal
  2 sep 03:36:02 2009 VPN Log Main Mode initiator
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > Send main initiator Mode 1 package
  2 sep 03:36:02 2009 charge of VPN journal received Vendor ID Type = [Dead Peer Detection]
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 2nd="" packet="">
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send Mode main 3rd package
  2 sep 03:36:03 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 4th="" packet="">
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > main initiator Mode to send 5 packs
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator receive hand Mode 6 Pack
  2 sep 03:36:03 2009 log VPN main mode peer ID is ID_IPV4_ADDR: '87.85.xxx.xxx '.
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN Mode main Phase 1 SA established
  2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] initiator Cookies = c527 d584 595 c 2c3b
  2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] responder Cookies = b62c ca31 1a5f 673f
  2 sep 03:36:03 2009 log quick launch Mode PSK VPN + TUNNEL + PFS
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator send fast Mode 1 package
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" quick="" mode="" 2nd="" packet="">
  2 sep 03:36:04 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba09
  2 sep 03:36:04 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = e3da1469
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
  2 sep 03:36:04 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
  2 sep 03:36:05 2009 VPN received log delete SA payload: ISAKMP State #629 removal

  PFS - off on tada and linksys router does not support the samsung lol! connected!

• ASA Syslog via a VPN Tunnel

  Hi all

  I have a little problem concerning ASA and syslogs. I have a tunnel from site to site between a local ASA and ASA distance. Behind the ASA local, I have a central syslog server (which has no ASA as default gateway) which collects messages from all network devices and I want to get messages from the ASA remote as well.

  The tunnel protects traffic between local networks behind each ASA, which includes ASA inside remote interface as well. The problem is that if I specify on the SAA distance my syslog server it does not pass through the VPN tunnel. The ASA remote sees my server syslog as being 'outside' so he's using the external IP address as the source-interface for the syslog message. Which of course does not pass through the tunnel. As much as I know there is no way to configure the interface source for logging under the SAA, that you can do on a normal IOS router.

  I've found a few documents explaining this Setup on CCO, but they all imply I have extend the list for interesting traffic to access allow remote UDP/514 of the PIX traffic outside my local syslog server interface. This isn't something I want to do what I would get in routing complication in my LAN with a public IP address of the ASA remote.

  Any suggestions? I thought I could use some sort of NAT on the ASA remote so that all traffic for my local network a source the remote PIX is translated on the inside interface, which in theory should pass the package via the tunnel. I did not go so far.

  Any help is appreciated.

  Best regards

  Stefan

  You can define the interface that the ASA will use to send the newspapers "syslog_ip host record.

  Make sure you also do "access management".

  Then the SAA should source the syslogs from inside the interface, which is probably encrypted with the crypto ACL.

  I hope it helps.

  PK

• Questions of VPN tunnel

  People,

  You can help me understand how I can fix the following issues I have with a 1721 router (Version 12.3 (8) T5) and client VPN 4.6.01.x please.

  BTW, the server at 192.168.3.2 is a file, DNS, WINS server and proxy for the LAN environment. All the staff of the PC is required to use the proxy but visitors on the 192.168.2.0 network can access the internet directly.

  Back to my questions. I have the obligation to set up a VPN tunnel to connect to a PC that is running Terminal Server services / remote desktop on a PC to 192.168.1.9. When running the VPN software on the laptop I get a login prompt and everything seems fine. I ping the addresses of router and that works.

  But the three things I don't understand:

  1. I can't telnet with great success to the loopback address of the router, as well as other addresses 192.168.x.x. very well, but why is it possible that I can telnet to the 192.168.4.1 loopback address?

  2. I can't DRC to the server on 192.168.3.2. The server can (and) accepts connections on a subnet, I created the network of 192.168.6.x I put up as VLAN6 on SEA4 (the port of spare on the map of ether 4 ports). The only thing I did not in the configuration of the interface was the nat ip within the statement.

  3. I can't do a nslookup through the tunnel VPN (delays all the time) and neither can I http to the IIS server on the same 192.168.3.2 box. What I mean here is that other applications seem to work except telnet!)

  Then...:

  Why the telnet is so special? I thought that if I could telnet to the router, then I should be able to access the server. And before ask you, there is no firewall or whatever it is executed on the server by stopping this stupid connections. Hey, I'm the guy from router, not the jockey of server!

  I've managed to misinterpret the statement "corresponds to the address 105" in the cryptomap? The ACL would reflect the traffic flow both ways?

  I should have a statement of hash in the section of "crypto isakmp policy 5. The client indicates that the connection is OK then why should I need it?

  I appreciate your time to help. I was scratching my head a lot in the last two days.

  Timothy

  Your NAT config, it is what kills you here. You can telnet to the router interface, because then the NAT configuration does not take effect (because NAT doesn't happen for passing traffic THROUGH the router, FOR her). You must refuse the IPSec traffic to be NAT would have, otherwise, it does not match the encryption access list and is not encrypted on the way back.

  Your 100 access list is incorrect, remove it and add in the following:

  access-list 100 deny ip 192.168.0.0 0.0.255.255 192.168.5.0 0.0.0.255

  access-list 100 permit ip 192.168.0.0 0.0.255.255 everything

  That said NAT VPN traffic does 192.168.5.0, but NAT do it if he goes anywhere else (Internet).

  Also, you seem to have defined a map static encryption for your customer traffic, it is not used and may cause you problems with the list of access-105. Follow these steps to get rid of it and just use the dynamic encryption card:

  no card crypto clientmap 1

  You just need to have dynamic instance map (number 20) crypto left in your config file.

• How to change an existing in ASDM VPN tunnel?

  I currently have a VPN tunnel together upwards, but to change some of the configurations as making ikev2, replacing the SHA512 hash and change it in the DH group 14. I intend to do this in ASDM. I already created a group of tunnel ikev2 that I put the tunnel and created a Card Crypto that is configured with the right proposal ikev2 IPSec and Diffie-Hellman group. All other configurations such as the IP of Peer address and subnets configured and I'll work with the engineers at the other end of the tunnel to ensure that configurations are, I want to just make sure I'm not missing anything. Someone at - he never comes to change the configuration of an existing ASDM so tunnel, and it worked correctly? Here are the steps that I have will be taken as well as those I've already mentioned:

  -Edit the connection profile so that the name of group policy use the correct tunnel that was created for ikev2

  -Enter the pre-shared key local and remote pre-shared key ikev2 tab

  -Change the IKE Policy so that it uses the ikev2 policy that was created to use SHA512

  -Modify the IPSEC proposal so that it uses AES256-SHA512

  -THE CRYPTO MAP IS ALREADY CREATED

  -Change the secret of transfer perfect in group 14

  Hello

  Let me go through your questions to clarify this double:

  1. If I have a Crypto map applied to my external interface with a proposal of IPSec of ikev1 can I just add a proposal ikev2 in this Crypto map as well?

  If you have a card encryption applied to different peers outside and 3 with different order number, you will need to replace the proposal for the peer using IKEv2: IKEv2 IKEv1, the others must continue to use their IKEv1 IPSec proposal.

  2. so can I add an ikev2 with AES256 SHA512 hash proposal to my 123.123.123.456 tunnel group and continue to have all three tunnel groups always pass traffic? What happens if I add the proposal ikev2, but REMOVE the ikev1 this group of tunnel proposal because I don't want this group of tunnel use one other than AES256-SHA512 hash?

  123.123.123.456 - ikev2 - AES256-SHA512

  I would like to expand this a little more, if her counterpart 123.123.123.456, must use IKEv2, you need to declare the IKEv2 in the tunnel group and add the relevant "Local and remote PSK"--> is for phase 1, and this means that it will use the IKEv2 defined policy before, and IPSec IKEv2 proposal is on phase 2, where the encryption card is you will need to replace the IKEv1 and use IPSec IKEv2 proposal. That way it will use for the phase 1 of the policy of IKEv2, that you set and defined transformation IKEv2, by making this change make sure that both sides are mirrored with IKEv2 and IPSec policy projects, as well as the tunnel will remain and will come with the new proposals.

  This custom affect no matter what another tunnel, as long as you change the settings to the correct tunnel group and do not delete all the proposals, simply remove the profile connection, those employees.

  3. you know what I mean? All groups of three tunnels on that off interface use different cryptographic cards, with only two of the three using ikev1 as a proposal of IPSec. Which will work?

  You can only have one card encryption applied by interface, and 3 tunnels using different sequence number with the same crypto map name, you cannot 2 tunnels on the same card encryption using IKEV1, and always in the same encryption card have the third tunnel using IKEv2 (different transformation defined using IKEv2). This custom cause no problem. 

  4. what Group Policy DfltGrpPolicy? Currently use all my groups of tunnel, but it is configured for ikev1. I'm not really sure what role is in everything it can so I simply add ikev2?

  Default group policy is added by default to all your groups of tunnel (connection profile), whenever create you one default group policy is inherited him by default, you can change to group policy that you can create, group policy is a set of attributes that will be used to define something or limit , for example, for a site, you can configure a VPN filter (filters the traffic that goes through the tunnel), now back to your topic, you define the protocols that will be negotiated as for an L2L IKEv1 or IKEv2, Anyconnect SSL or IKEv2, on default group policy, and so on, it is therefore important that you add the IKEv2 , so trading will be permitted, or both to create a new group policy and add the IKEv2 Protocol; and in the tunnel group, add the group policy relevant, that you just created.

  I hope that this is precisely, keep me posted!

  Please go to the note, and mark it as correct this post and the previous that it helped you!

  David Castro,