Cisco ASA 5515 two asa firewall ipsec vpn tunnel is not coming

Similar Questions

• ASA Cisco IPSEC VPN tunnel has not managed the traffic

  Hi guys

  I am trying to set up a new connection IPSEC VPN between a Cisco ASA 5520 (verion 8.4 (4)) and Checkpoint Firewall. I managed to establish the phases IKE and IPSEC and I can see the tunnel is UP. But I can't see any traffic through the tunnel. I checked the cryptomap both ends and try to test with a contionuous ping from within the network of the SAA.

  I made a screenshot of ICMP packets but cannot see in ASA. I welcomed the icmp inside ASA interface.

  I did a package tracer and it ends with a fall of vpn - filter the packets. But can not see any configured filters...

  Your help is very appreciated...

  Thank you

  You probably need to add nat negate statements:-something like.

  object-group network OBJ-LOCAL
  Network 10.155.176.0 255.255.255.0
  object-group network OBJ / remote
  object-network 192.168.101.0 255.255.255.0
  NAT static OBJ-LOCALOBJ-LOCAL source destination (indoor, outdoor) static OBJ-REMOTE OBJ-REMOTE-no-proxy-arp

  You are running 8.4 nat 0 has been amortized

• Cisco ASA 5510, ipsec vpn. What address to connect the client to

  Hello

  It's maybe a stupid question, but I can't find the answer anywhere.

  I used the ipsec vpn configuration wizard, I activated the external interface to access ipsec and went through SCW pools of addresses etc. When I try to connect with the cisco vpn client to my address of the external interface (of a remote host) I'm unable to connect. I scanned the interface for open ports, but there is not, I have to allow traffic to ipsec at this interface?

  Best regards

  Andreas

  No, once you have configured the access remote vpn ipsec, it will be automatically activated, and you should be able to connect to the ASA outside the ip address of the interface.

  Can you please share the configuration? and also which group name you are trying to access the vpn client?

• Routing access to Internet through an IPSec VPN Tunnel

  Hello

  I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.

  I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.

  Any help would be greatly appreciated.

  Thank you.

  Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.

• IPSec VPN tunnel only to come

  Hello

  I am trying to configure an IPSec VPN tunnel between my company and a remote company for the use of FTP secure.

  I used the SDM to configure the tunnel on my router based on the information provided by the society that we are trying to connect to. The other company has provided my debug log when I was testing the connection, but I do not know how to read and what could be the problem. I hope someone here can give me an overview of what prevents the tunnel connection.

  Please let me know if you need more information.

  Thank you

  Peter Haase

  Peter,

  Good job!

  Because the tunnel is up, we must not debugs.

  I'm glad that finally it works.

  HTH

  Sangaré

• Cisco ASA - l2l IPSEC tunnel two dynamic hosts

  Hello

  I have two firewall Cisco ASA an i want to made a l2l between two ipsec tunnel, the problem is that both parties have a dynamic IP, on both sides I have configured dyndns, can I did an ipsec tunnel using dyndns name such as address peer?

  Hello

  ASA supports only the RFC compliant method for updates used with dynamic DNS, not updates HTTP, such as dyndns.org and others use.
  i.e. https://tools.cisco.com/bugsearch/bug/CSCsk25102/?reffering_site=dumpcr

  On ASA, it is not possible to configure the tunnel between two dynamic peers.
  You will need to have a static end to configure static to dynamic IP.

  For routers, you can follow this link.
  I hope this helps.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Install two the separate IPSec VPNS on ASA 5505

  Hello

  I'll have set up a second tunnel IPSec VPN on my Cisco ASA 5505 to another office.  I was able to configure one without problem through the ASDM, but were not able to get the second.

  The IPSec tunnel connects to a WRVS4400N router to the other office.  I tried the debug crypto isakmp and ipsec crypto, but I get nothing.  Here is the config.  Something seems wrong on my end?   I've also attached a screenshot of the configuration settings on the remote router.

  Output of the command: "show run".

  : Saved
  :
  ASA Version 8.2 (5)
  !
  hostname WayneASA

  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 70.91.18.205 255.255.255.252
  !
  interface Vlan5
  Shutdown
  No nameif
  security-level 50
  IP 192.168.10.1 255.255.255.0
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  75.75.75.75 server name
  75.75.76.76 server name
  domain 3gtms.com
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  inside_access_in of access allowed any ip an extended list
  IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
  TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
  outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0

  pager lines 24
  Enable logging
  Within 1500 MTU
  Outside 1500 MTU
  IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0
  NAT (inside) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group
  Access-group out_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto IPSec_map 1 corresponds to the address IPSec_Access
  card crypto IPSec_map 1 set peer 50.199.234.229
  card crypto IPSec_map 1 the transform-set VPNTransformSet value
  card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
  card crypto IPSec_map 2 set pfs Group1
  card crypto IPSec_map 2 set peer 98.101.139.210
  card crypto IPSec_map 2 the transform-set VPNTransformSet value
  card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  IPSec_map interface card crypto outside
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.199.234.229

  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH timeout 60
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.100 - 192.168.1.199 inside
  dhcpd dns 75.75.75.75 75.75.76.76 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal RemoteTunnel group strategy
  attributes of Group Policy RemoteTunnel
  value of server DNS 75.75.75.75 75.75.76.76
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
  3gtms.com value by default-field
  eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
  username password encrypted URsSXKLozQMSeCBk privilege 5 lestofts
  username lestofts attributes
  type of remote access service
  algobel lBWy5eNbHMCDPzuL encrypted password username
  username algobel attributes
  type of remote access service
  type tunnel-group RemoteTunnel remote access
  attributes global-tunnel-group RemoteTunnel
  address pool VPNPool
  Group Policy - by default-RemoteTunnel
  IPSec-attributes tunnel-group RemoteTunnel
  pre-shared key *.
  tunnel-group 50.199.234.229 type ipsec-l2l
  IPSec-attributes tunnel-group 50.199.234.229
  pre-shared key *.
  tunnel-group 98.101.139.210 type ipsec-l2l
  IPSec-attributes tunnel-group 98.101.139.210
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the icmp
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the dns
  inspect the pptp
  inspect the sip
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call
  Cryptochecksum:a86adc4b23977672679b6fb72d0bc187
  : end

  You are also missing the NAT0 rule

  inside_nat0 to access extended list ip 192.168.2.0 allow 255.255.255.0 192.168.5.0 255.255.255.0

  -Jouni

• VPN Cisco ASA Cisco ASA firewall via DHCP.

  Hi all!

  Small question.  I have an ASA5520 (8.2) acting as a VPN server with the correct configuration to request a DHCP on behalf of the VPN Client address.  However, this ASAVPN is connected to a vpn - dmz on my other ASA5520 (8.0) is our main firewall.  I can see future demand across the demilitarized zone and the ASAFIREWALL interface inside and outside.  The DHCP server responds and refers to the x.x.x.0.   I had not initially installing dhcp on the ASAFIREWALL relay as I had open 67 upd, thinking it would allow just back through with number.  No idea how to get this working correctly?

  Thank you

  Raun

  Hello Raun,

  Please see the link among Cisco engineers.

  It will help you on this

  https://supportforums.Cisco.com/community/NetPro/security/firewall/blog/2011/01/07/ASA-PIX-DHCP-relay-through-VPN-tunnel

  Any other questions... Sure... Be sure to note all my answers.

  Julio

• How to move the ASA of IPSEC VPN via UDP to TCP

  I have a client who has a remote desktop with 2 PCs than VPN in to their location of HQ. Previously, two computers where in different places now that they are in the same place. Both PC's are able to successfully establish a VPN connection to the CA by using the Version of the Client VPN Cisco 5.0.07.0290, but only 1 system actually passes the traffic and is able to access the resources at Headquarters.

  I asked another engineer, and they said ' you must configure IPSEC over TCP or use Anyconnect to have multiple clients behind the same PAT' public ed remote ip address... ". ». I would go with IPSEC for TCP connection, so I won't have to uninstall the old client and go through the process of installing the AnyConnect client. Here is the configuration of the ASA 5505 thanks in advance for any help.

  CLIENTASA # sh run

  : Saved

  :

  ASA Version 7.2 (4)

  !

  hostname CLIENTASA

  domain client.local

  activate 72LucMgVuxp5I3Ox encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x where x.x.x.x

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain client.local

  standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0

  outside_in list extended access permit tcp any any eq smtp

  outside_in list extended access permit tcp any any eq www

  outside_in list extended access permitted tcp everything any https eq

  access-list extended sheep allowed ip 192.168.1.0 255.255.255.0 10.99.99.0 255.255.255.0

  pager lines 24

  Enable logging

  recording of debug console

  debug logging in buffered memory

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  pool local IP VPN-10.99.99.100 - 10.99.99.200

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 523.bin

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static tcp (indoor, outdoor) interface www 192.168.1.2 netmask 255.255.255.255 www

  public static tcp (indoor, outdoor) interface https 192.168.1.2 netmask 255.255.255.255 https

  public static tcp (indoor, outdoor) interface smtp 192.168.1.2 netmask 255.255.255.255 smtp

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  AAA authentication enable LOCAL console

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-3des esp - esp-md5-hmac

  Crypto dynamic-map VPNDYN 1 set transform-set esp-3des

  vpn ipsec dynamic VPNDYN 65535-isakmp crypto map

  vpn outside crypto map interface

  crypto ISAKMP allow outside

  crypto ISAKMP policy 100

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 5

  Console timeout 0

  dhcpd dns 192.168.1.2

  dhcpd outside auto_config

  !

  des-sha1 encryption SSL rc4 - md5

  VPN-POLICY group policy interns

  attributes of VPN-POLICY-group policy

  value of server DNS 192.16.1.2

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value of SPLIT TUNNEL

  admin PWpqnmc2BqJP9Qrb encrypted privilege 15 password username

  password encrypted vpn2 ZBNuNQsIyyMGbOB2 user name

  username vpn3 encrypted password 15c4LrPNccaj1Ufr

  vpn1 fsQgwXwSLokX6hEU encrypted password username

  tunnel-group CLIENTVPN type ipsec-ra

  attributes global-tunnel-group CLIENTVPN

  address VPN-POOL pool

  Group Policy - by default-VPN-POLICY

  IPSec-attributes tunnel-group CLIENTVPN

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:41bd95c164a63bb26b01c109ab1bd68a

  : end

  CLIENTASA #.

  Hello

  You can try adding

  Crypto isakmp nat-traversal 30

  And test connections

  I think that you need to add to use the TCP protocol

  Crypto isakmp ipsec-over-tcp 10000

  You will also need to change the Transparent tunnel setting on the profile of Client VPN software to use TCP instead of option of NAT/PAT.

  -Jouni

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

• Cisco ASA and dynamic VPN L2L Fortigate configuration

  I met a problem recently with an ASA 5510 (7.0) and a bunch of Fortigate 50 (3.0 MR7). The ASA is the hub and Fortigates are rays with a dynamic public IP.

  I followed this document on the site Web of Cisco (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml) to set up my ASA and the parameters passed to my counterparts to set up their Fortigates.

  However, the ASA journal reveals that attemtps Fortigate connection always tried with DefaultRAGroup before falling back to DefaultL2LGroup and finally died. Experience with putting in place a dynamic VPN between Cisco and Fortigate someone? Which could not fail at each end? Here's a typical piece of error log ASA. The ASA is currently having a static VPN tunnel and a site-2-client VPN in two groups by default.

  6. January 10, 2011 20:58:45 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:45 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:45 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:45 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:41 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:41 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  4. January 10, 2011 20:58:39 | 713903: Group = DefaultL2LGroup, IP = 116.230.243.205, ERROR, had decrypt packets, probably due to problems not match pre-shared key.  Abandonment
  5. January 10, 2011 20:58:39 | 713904: Group = DefaultL2LGroup, IP = 116.230.243.205, received the package of Mode main Oakley encrypted with invalid payloads, MessID = 0
  6. January 10, 2011 20:58:39 | 713905: Group = DefaultRAGroup, IP = 116.230.243.205, WARNING, had decrypt packets, probably due to problems not match pre-shared key.  User switching to the tunnel-group: DefaultL2LGroup
  5. January 10, 2011 20:58:39 | 713904: Group = DefaultRAGroup, IP = 116.230.243.205, received the package of Mode main Oakley encrypted with invalid payloads, MessID = 0
  4. January 10, 2011 20:58:33 | 713903: Group = DefaultRAGroup, IP = 116.230.243.205, error: cannot delete PeerTblEntry
  3. January 10, 2011 20:58:33 | 713902: Group = DefaultRAGroup, IP = 116.230.243.205, Removing peer to peer table has no, no match!
  6. January 10, 2011 20:58:33 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:33 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:25 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:25 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:21 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:21 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  5. January 10, 2011 20:58:19 | 713904: IP = 116.230.243.205, encrypted packet received with any HIS correspondent, drop

  Yes, sounds about right. He will try to match with the DefaultRAGroup first, and when you know that it's a dynamic IPSec in LAN-to-LAN, it will be

  then back to the DefaultL2LGroup, because he doesn't know if the VPN Client or L2L again when he is contacted fist as they are connecting from dynamic IP peer.

  You must ensure that your L2L tunnel-group by default has been configured with the corresponding pre-shared key.

  Assuming that you have configured the dynamic map and assign to the card encryption.

  Here is an example of configuration where ASA has a static and peripheral ip address pair has dynamic IP:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  Hope that helps.

• ASA 5505 ipsec vpn connection fails

  Hello

  I'm trying to configure a Cisco ASA 5505 for Remote Clients.

  I use the ASDM interface and used assistants start and ipsec for my setup, but im hit a stumbling block.

  To last make it work 2 days I have tried a number of configuration changes to try to make this work but didn't, so I did a factory reset and passed by the assistants, once again, I have a clean Setup that I hope someone can help me.

  Currently I have an IP public static 81.137.x.x and I use a Netgear ADSL router, which transfers (UDP 500) VPN traffic to 192.168.171.35 (port wan on the ASA 5505).

  The Cisco ASA has a default address of 192.168.1.1

  I use the Cisco Client 5.0.06.0160.

  I have configured the client to use authentication group with the same credentials as configuration through the wizard and im using Transparent Tunneling IPSec over UDP.

  I have attached 2 documents

  running_config.txt - what is shows the current configuration of ASA

  Journal - View.txt - display of error messages displayed in the real-time log viewer when I try to connect from the remote client.

  I'm not sure if I need to do on the other that additional configurations for my setup simply run the wizards.

  Any help would be appreciated.

  Thank you

  Hello Philippe,

  According to the lines in the journal, there is a problem of routing for ip vpn applicant address. ASA couldn't find the definition of route suitable for the return traffic. Add a default route to unknown destinations could solve this problem. As I see you are using modem netgear as a default gateway for your ASA. I write example of command line for this purpose.

  Route outside 0.0.0.0 0.0.0.0 NetGear_LAN_IP_Address 1

  Ufuk Güler

• Limited Cisco ASA 5510 IPSEC

  Hi guys

  There are IPsec deadline for ASA 5510?

  There are users complain on connected, they cannot access any server on the local network. but now it works fine

  .PNG

  

  Hello

  What do you mean by limit? The number of IPSEC sessions is limited to 250, if I remember correctly.

  To limit access to internal resources, there is not.

  These users complain using the same IPSEC vpn as others? Is that your exemption of crypto and nat that allows all internal resources?

  Thank you

  PS: Please do not forget to rate and score as correct answer if this answered your question

• ASA to 1841 VPN Tunnel

  Hello

  I am trying to establish a VPN tunnel from site to site between 2 offices. An agency has a Cisco 1841 and the other a pair of ASA 5510. I get the tunnel to establish without problem. The problem is that traffic will the intended to the ASA 1841 will not encrypt to this particular tunnel. I get decaps on the session, but no program. I've reconfigured the tunnel several times but keep getting the same result:

  Interface: FastEthernet0/1
  The session state: UP-ACTIVE
  Peer: 202.41.148.5 port fvrf 500: (none) ivrf: (none)
  Phase1_id: 202.41.148.5
  DESC: (none)
  IKE SA: local 81.218.42.130/500 remote 202.41.148.5/500 Active
  Capabilities: (None) connid:98 life time: 23:45:02
  FLOW IPSEC: allowed ip 192.168.5.0/255.255.255.0 10.0.96.0/255.255.240.0
  Active sAs: 2, origin: card crypto
  On arrival: dec #pkts'ed 17 drop 0 life (KB/s) 4569995/2704
  Outbound: #pkts enc'ed drop 0 0 life (KB/s) 4569996/2704

  Any suggestions would be greatly appreciated.

  Andy

  Your ACL 100 is not exempt traffic 192.168.5.0-> 10.0.96.0 of the NAT process.  Please add the line below above the permit statement and test again.

  access-list 100 deny ip 192.168.5.0 0.0.0.255 10.0.96.0 0.0.15.255

• Cisco ASA cannot create several tunnels at the same address in hand?

  We have several remote sites with Linksys WRVS4400N and Smoothwall firewall/vpn devices.  I need these sites to be able to connect to several tell-contiguous subnets to our main office.  This was done easily with smoothwall and linksys.  You create a separate tunnel for each subnet, and voila, you're done.  However, when I tried this with our ASA newly installed, it won't let me create several tunnels at the same address of the remote peer.  It is a problem because these sites have only a single IP address public static.  Did I miss something or ASA not allow connections to and from multiple subnets form a site with a unique address peer?

  Resembles the limitation on the WRVS4400N as Cisco ASA supports several subnets by tunnel.

  Is there anyway that you can configure a subnet more instead of specific subnets on the ACL?

  For example:

  If you 192.168.0.0/24 and 192.168.1.0/24, instead of having 2 subnets configured, you can combine them into 1 subnet 192.168.0.0/23