BIOS setings

Similar Questions

• HPMINI 110-3030NR UPDATE BIOS. "Sum of CMOS is invalid health check", check if the bios setings can change. ' RESET CMOS < 502 > reset to the default values.

  I; m getting this message during the installation of the new bios. my touch pad is going crazy, then I was told by hp to update bios F 0.6 to F06 f. However when I turn the computer back lights are not flashing and I get this message "CMOS is invalid health check sum", check if the bios setings can change. reset to default values". HP doesn't seem to know what the problem is. can anyone help. It's a netbook new, purchased in the States but in Malaysia now and he cannot return as too costly. Help, please...

  Please repost your request to the experts in the Forum for HP laptopcomputer laptop HP.  Thank you! Carey Frisch

• It takes a long time to access BIOS on the Qosmio X 300 after replacing the mobo

  I JUST REPLACE THE MOTHERBOARD ON A QOSMIO X 300 AND IT TAKES FOREVER TO GET INTO THE BIOS SETINGS, ABOUT 40 MIN. AND WHEN ITS IN, IT DOES NOT RECOGNIZE THE TWO HARD DRIVES.
  THE NEW MOTHERBOARD IS THE NUMBER OF EXACT AS THE ORIGINAL PIECE.

  I TRIED THIS DRUG AND IT DOESN'T WORK...

  Help, please.

  I agree, the RAM should be tested in the case contrary you did something wrong during the process of replacement/disassembly may be the mobo was already damaged

• upgrade memory in a Portege 3410ct

  I tried installing memory of 128 MB PA3034u 3410ct, but on commissioning a message comes up saying that the ACPI BIOS is not fully compliant with the ACPI specification.
  I downloaded the latest BIOS setings but makes no difference. Will not start just yet. Clues as to correct the problem, other that not upgrading memory.

  Hello!

  This problem may occur if you add the memory (RAM) to the computer when it is in hibernation.

  When the computer comes out of hibernation mode and load the file Hiberfil.sys, Microsoft Windows detects the change in the State of the memory, and then you receive the error message.

  To resolve this issue, restart your computer.

  If the problem persists, start the computer by using an emergency boot disk, and then delete the Hiberfil.sys file.

  Good bye

• Satellite L350D - 20 d - question about graphics card memory

  Hi on start I want to sorry for my bad language lol

  I form a few days TOSHIBA SATELLITE L350D - 20 d
  I WIN with Vista reinstaling for XPsp3 after 29 hours of blame Microsoft for making Vista. or m.Kin another and another bootUSBpendrive and the mixture of the BIOS setings... succecfull Finally I reinstal system DVD... BUT!
  This may sound strange, but on Vista when I was check my details Graphisc in DxDiag I saw 1 700 MB of RAM... even with the RAM into the motherboard... RAM on the motherboard had 4GB...
  now I have Xp-Windows7(what is XPSP3) but modifited!... I've been using original Toshiba drivers from this Web site. .and I see now...
  My Ram on the card mother down t o 3.5 GB... and graphics card is about 700 MB of ram... I can say WTF...
  IM really not sure if this computer is ABLE to have 1 700 MB graphics card... That's if I remember well AtiRadeon 3100... or sometihnk...
  anyone has the same Toshiba model?... I want to compare the details of the hardware with this one to what I have now on my Toshiba SATELLITE L350D - 20 d...

  Edit:
  resolution, what I have now and it is maximum that I can choose its 1440 x 900 at 60 Hz only :/
  on the site Web of TOSHIBA Germany I see somethink difrente:

  Grafikadapter type: ATI Radeon 3100 Graphics
  RAM: Bis zu 1 407 MB complete Rechtssicherheit Grafikspeicher EIB 3 GB Arbeitsspeicher
  RAM type: geteilt
  Internal Auflösung Verfügbare video in-house Modi
  Auflösung: 1,440 x 900
  Auflösung external maximum maximum Auflösung: 2.048 x 1.536
  maximum Bildwiederholfrequenz: 85 Hz
  maximum resolution (not interlaced) EIB Genauigkeit Bildwiederholfrequenz: 1,600 x 1,200

  Post edited by: MzytengaM

  > I want screan LCD stop down and stay mobile mind on... no sleep or standby extended... CUS I use external monitor... and I want to save battery power.

  I found a small free tool called turn the wide-screen LCD. You can google for it if you want.
  But as far as I know, this tool is only compatible with Win XP and Vista, so I don't know if it will work on laptops with pre-installed m Win 7.

• failure of restoration of 7201tx dv7 help im ready to hit it with a hammer and fix it forever

  My DV7 7201tx fails to restore it all goes the way to restart and loading of software etc. and even in windows 8, but only once and then it tells me that the restoration failed and locks the admin VAC and from there it just request the recovery media every time the computer starts, and it's like it goes , it will not go in the bios setings it will not choose a different boot device, it won't do anything except ask the media to restore which I give, but it does nothing. After the call to support the guy on the ph HP tells me that my restore media is defective. If I order and get the complete set of recovery DVD and try again with the same result. I forgot to mention to recover all over again, I have to remove the hard drive and put it in my Acer and then boot from a live cd of ubuntu and use Gparted to format the drive, so I can go through the whole process again... with the same results. I tried so many times now with the same result. Strange thing is I can load on my copy of win7 and it works fine, I can load on linux and it works fine, but try and load the media that come with the laptop and it's a total failure... This lappy is only 2 months old and im ready to cut my losses and smash with a hammer... This is my last resort to operate properly with the system, it came with... not that there will be a new vid on youtube to destroy me this laptop... Thank you and please someone HELP

  you are a man of legend... He worked freekin, the restoration went as it should have, and I have my computer back to factory settings... You saved my lappy to get a severe beating... awesome

• Compaq SR5010nx

  Don't see WOL in the bios. Realtek network card has the latest win7 driver. Under power management allow for wake up the computer is grayed out. What are my options to get workking WOL?

  Running Win7 x 64

  rgf704,

  Welcome to the forums.

  Here is a guide. WOL is explained in step 6, but article has BIOS setings:

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power

• l want to restore my labtop factory setings. Help

  I use Vista home premium.my labtop dosnt work normally, l want to restore my labtop factory setings. What I can?

  Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon.

  Mick Murphy - Microsoft partner

• How to enter the bios to the macbook pro

  Hello

  How enter the macbook (Command + Option + O + F) bios does not work in my MacBook Pro (13-inch, mid 2009).

  Macs with Intel processors as you do not have a bios (firmware 0pen), it uses EFI (Extensible Firmware Interface).

  What you trying to accomplish?

  This is the Office Mac Pro forum. I asked that your post moved to the forum of laptop MacBook Pro or another appropriate forum.

• Update the BIOS

  Hello

  can someone tell me the Bios updates for my machine?

  I need one that is more aggressive on material resources. The appropriate drivers for the GPU would be nice as well. Reading from data bases of Geekbench, this machine is never more than a pretty paperweight to research.

  Thanks for reading

  Details in the following way:

  Motherboard: Apple Inc. Mac-B809C3757DA9BB8D iMac17, 1

  BIOS: Apple Inc. IM171.88Z.0105.B08.1604111319

  Memory: 32768 Mo 1867 MHz DDR3

  Processor: Intel Core i7 - 6700K @ 4.00 GHz

  GPU: AMD Radeon R9 M395X 4096 MB

  macpraxis,

  You confuse a Mac to a Windows window. Mac do not have a bios but they have firmware, if there is any necessary updates to your machine, they are available in the software updates which is located in the Mac App Store. If nothing comes, while your system is up to date and should be left alone.

  If you encounter any problem, perhaps to let us know what it is would open the way for getting help.

• Pavilion dv7 6163 cl: unlock (reset) password on BIOS/CMOS for HP DV7 - 6163cl

  The bios of my notebook (Pavilion dv7 6163 cl) blocked by password, and I never put a password. Could you help me solve?

  Enter the wrong password 3 times or simply leave them blank and press success enter 3 times. You should get a stop code. This zip code here.

  https://BIOS-PW.org/

• Pavilion 15: Bios password

  I have a Pavilion 15-e022sa which I just can't get into the bios as it says I need a password that I never put someone could please help

  Hello

  Enter 60081217

  Kind regards

  DP - K

• 8570p: 8570 bios password

  We have our password bios laptop company typed wrong and how stop us this case? Access the bios has it boot in network again.

  Dear customer,

  Welcome to the Support Forum HP and we are happy to help you.

  This is to inform you that all professional laptops HP Probooks as EliteBook have tighter security than the consumer models infact they do not produce ' stop codes ', the password cannot be derived from the serial number and the

  code is stored in a memory not volatile to remove the cell RTC does not reset the password in this case.

  1. Please take a look at this link.

  http://forums.mydigitallife.info/threads/49497-HP-ProBook-EliteBook-BIOS-password-reset-utility

  1. Replace the BIOS chip

  http://www.eBay.com/ITM/HP-EliteBook-8470p-8470w-8570p-8570w-8770w-programmed-BIOS-chip-no-password-new-/251583542720?PT=LH_DefaultDomain_2 & Hash = item3a938c35c0

  1. Please Contact HP Business Notebook of support they should be able to send a SMC.bin custom file that you can use to reset the password at startup.

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the button white Thumbs Up on the right of say thank you*.

  Make it easier for others to find solutions by checking a response 'accept as Solution' if it solves your problem.

  Thank you

  GBL84

  I'm not an employee of HP

  https://DL.dropboxusercontent.com/u/26983620/Java_Bios/biosunlock.html

• Clocked at 20 degrees warmer since putting on 3.87 Rev A Bios Update on Z420 Workstation

  I have a question:

  Not too long ago I put the Bios Update on A Rev 3.87 was considered to be as critical an update on my workstation Z420 (running Windows 7 Pro 64-bit), and lately I've found that the CPU idling at about 20 degrees more hot than before.  I used to hear creaking noises coming from the computer I learned normally come circuits on the motherboard power delivery, but as long as I heard those CPU would be on average around 50 degrees C at idle.  I hear these noises and now the CPU is on average around 70-75 degrees C at idle.  Not sure what the connection is.  HP performance Advisor tells me I'm in the normal range, but I want to just make sure that with programs like Autodesk Maya there, she become too hot and stop the machine.   I don't know what the temp high-end is considered maximum security.  This change could have due to the update of the Bios?

  Thank you for your response and suggestions.  I check in my BIOS power management settings has been developed the extended mode, but the temperature has always hovered around 70-78 degrees at idle.  I checked Intel spec for this (E5 - 1650 6-core xeon) processor, clocked at 3.2 Ghz by heart, and although he said nothing on the TMax, he mentioned that the TCase (which he defined as the maximum temperature allowed integrated processor heat sink (IHS)) was 64 degrees Celsius.  Now my temperature of the case, according to my HP Performance Advisor version 1.7.7517.0 is only about 24 degrees C, but I put my fan a little higher CPU, about 2009 rpm speed.  This makes a little more noise, but my CPU temp has dropped to about 49 °.  "" Before the change of the fan speed has been slightly more than 1300 RPM while the Advisor I have always said that it is in the range "normal".  Is it good to get the speed of the CPU fan like that or do I have to go a little lower?

  James Holman

• All BIOS options are disabled / grayed out

  I have 8770w with HP ProtectTools active EliteBook and just to have on the security of the TPM secure. I rebooted and tried to access the BIOS, my password is accepted, but virtually all of the options are disabled. Any idea what's going on here?
  Is it the TPM chip?

  In fact, the solution was to open a session in the BIOS as a guest and then configure a BIOS Admin password. Thank you post that.

  It is odd that the default user does not receive the Admin of the BIOS rights.