BlackBerry Curve 9300 Smartphone disconnects from the network - no BBM, email etc. - send or receive

Similar Questions

• SOLUTION for your HP printer disconnect and/or constantly disconnecting from the network

  If you are having a problem printing, scanning or fax with any HP printer because of this be disconnected and constantly disconnecting from the network, here again is the fix!

  I thought that this all after several failed attempts with HP Support, my Internet access provider and various troubleshooting tasks including reinstall the HP software and more and more.  Well, through self teaching on internet and exhausting search for 6 months, I FINALLY thought to it.  OMG!  I'm a paramedic (not IT) and a little computer but far not an expert.  I have all of you here!  Nobody seems to have the answer, but I'm sure that I'm doing it to 97%.  Whatever it is, if it please answer and let me know that it worked for you!  :-)

  It doesn't matter if your printer is installed cable or wireless.  You don't reinstall your software, no recycling power of your printers or your router/Modem.  Your printer is unstable on the network and continues to log out or disconnect from the network it is NOT because the software is glitched, it isn't a firewall problem by saying, is not a router problem, is not a problem with your power cord, because most networks use a 'Beach' and IP addresses for security reasons This kind of "cycles" the IP addresses of the devices to reduce the risk of an attack.  A printer is not a threat, but the 'network' don't own human intelligence, so he does not know this.  Here are my step by step instructions on how to basically your printer address IP (static IP) instead of change back through a cycle so drop your printer on the network or disconnected.

  Funny, if you're someone who has had the elements in your print queue, they will not print, and you turn your printer off and on again and suddenly your print... well documents, join my club.  The reason it works is that when you turn on the printer, it starts with the same IP address before cycle.  If you are someone who is sitting there for a while and all of a sudden your printed documents without changing you something... it is because through the cycle of change of IP address, it hits your printers IP address and the network would allow him to print.  Not very funny, I know.  It took me forever to figure out why my printer would print sometimes, but not always.  Since I thought at this point, I can SCAN, PRINT, and use all the features of my HP software installed like HP, Photosmart Essentials Solution Center.

  On your printer, go to menu/Setup/network and press OK.  In the network menu, print a "network configuration page" so you can see the IP address and other settings of your printer.

  Now, back to the main menu on the screen of your printers.  Or you can go to your web browser and type the IP address using decimal numbers too and this will take you to the web page of your printers.  Choose: setup\network, then press OK.  Look for the IP settings and press OK. Choose "manual" instead of "automatic". Manually enter the IP address it as well as the default gateway that you can see the Network Setup page you printed earlier.  Note: If you manually set the IP Address of the printer, make sure that it is outside the range of your router's DHCP. Otherwise you might encounter a problem with IP addresses on your network duplicate. (If you don't know how to do this, write back and I'll explain).  Don't forget to click "save changes".  Now, restart your computer, and print just what you want.  :-)

  A trick I often use with DHCP network printers:
  In printers and faxes, right-click on the printer and select "Properties".  Click Add a new port.  Choose standard TCP/IP port configured for the host name of the printer. Read the host name of the network printer configuration sheet.
  
  Using my method means that you always connect to the printer even if its IP address changes (which can happen with the dynamic configuration). This does not jeopardize the security of your network.  It shows just your printer to stay put and stop traveling the highway of IP address.  :-)

  The DHCP range is the range of IP addresses that the router distributes automatically as devices to join the network.  The DHCP range is determined by the router and each brand has a range that is set at the factory (which can be changed by you).

  Default value for the DHCP of your D-link is 192.168.0.100 to 192.168.0.199.  Thus, outside the DHCP range est.2 a.99.200 a.254.

  Is a handy cheat sheet attached.

  You can change this interval by entering the router settings page - type the router's IP address in a browser, enter the login information and access the DHCP parameter area (varies depending on router, hunting around).

• Satellite A200 Win8 64bits - Atheros AR5006EX disconnects from the network at random

  First of all, sorry for my bad English.

  Hi, I installed W8 a few weeks ago and I have a problem with the WiFi. The adapter disconnects from the network at random. Not a protocol TCP/IP fail because I don't lose the connection to the internet, I lose the connection to the network for everyone.
  Simply disconnected from any wifi network.

  I have read that wifi chips Qualcomm have problems with drivers in W8. I tested many pilots and all do not work properly.

  Any help?

  The wifi card is: Qualcomm atheros AR5006EX and the laptop is: Toshiba satellite A200-1TP.

  Drivers I tested (and didn't work):

  http://drivers.Softpedia.com/get/network-card/Atheros/Atheros-AR5006EX-WLAN-driver-300119-for-Windows-8-x64.shtml

  Thank you!

  Do you have these problems with the operating system supported?
  I mean A200 is pretty old machine and certainly not supported for Win8, so it can be a problem with all of this, especially with the drivers.

  Let's see if someone else has the same machine and have the solution to this.

• Current file to use when it is disconnected from the network wireless/wired - shared network drive

  Hello

  We have a problem where we receive a "file in use" message when you are disconnected from the network. To reproduce the problem, what we do is:

  (1) connect to the wired network wireless disabled with

  (2) create a test document

  (3) to enter text and save on network share

  (4) remove the network cable

  (5) add additional text

  (6) reconnect the network cable

  (7) try to save the file to the network share

  At the beginning by clicking the X is the new message you want to save. Click Yes and the message arrives until the next time you hit the Hit of X no. and he loses the last change.

  From here we then go up to the network share, open the file and it comes up with "file in use. Open read-only. File is opened by us (Administrator account), and there is NO temporary file in the shared folder.

  Tried so far:

  -Run net config server/autodisconnect:-1 for trying to stop it disconnect the share

  -Checked pane, pane preview and off 'display the description of the pop-up window for folder and desktop items '.

  -Windows Update

  We try to reproduce on wired connection, because it is easier to reproduce that disconnects wireless. Seems to have an impact on several operating systems. Share folder is shared on a Windows 2008 R2 x 64 machine.

  Is this a known problem or is there something that we can configure to try to prevent the locking file after logging out? Ideally, we want the decline to go unnoticed and provide uninterrupted service to the user, unless they are trying to save during the fall.

  Thanks in advance for comments :)

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• After time computer disconnects from the network

  When I connect to my domain I can open my outlook uses exchange server without password, share my printer on the network, and access to network files.   After some time the printer is disconnected from the network be connected (always available for me no network) my email brings me a password and all shared network files ask me for a password.

  My computer is windows xp pro, we have 2 other xp pro connected machines that do not have this problem.

  I also never lose my internet or the ability to access any network files that I just asked for a username and pword after a few minutes.

  Only way to fix the printer and the problem is a reboot and relog in.

  Hello

  Questions like these are much better handled in the TechNet IT Pro Forums.

  My moderator tools cannot transfer messages on Windows forums, please re - ask you question there.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads
  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Disconnecting from the network home

  Win 7 I have a stand-alone computer (not other computers) with a USB - connected printer and a connection to a modem (without router) via a network (?) (not USB) cable.  I have no other computers or printers.  Win 7 connected me to a network home, maybe because my printer is compatible with wireless (but I have no WiFi - or interest in functionality).  If I disconnect the home network I lose the internet connections or printer?

  My apologies but I found your statement at the opening a bit confusing.

  Your home network is connected to the modem, a local area network, and is a type of HOME that helps your computer share with a reliable source, connected to your modem/router.

  A HOME network is essentially the default setting...

  A PUBLIC network limited with any computer that can be attached to your router/modem to share files.

  If your printer is connected via a USB cable, disconnect from the network will NOT affect the communications between your computer and the printer and the printer will do what you expect it to do.

  However, you will lose Internet you disable the network connection.

• BlackBerry Smartphones Blackberry Curve 9300 3: Problem with the camera without flash and don't take pictures

  Hello!

  I have a Blackberry Curve 9300 3 phone. Until recently my camera was working fine that is the camera takes pictures. But recently I can't take pictures. I can access the camera screen I can zoom in I can see old photos but when I click on the camera icon to take a photo there is no flash and no picture is taken (as a video of tmy note side works fine)

  Any ideas of what can be the problem? Also is it a good idea to remove the battery to fix the problem and if I did so will alll my similar memos, contacts etc. be erased?

  Thank you very much!

  removing the battery may fix some glitches on the phone but it clear files from the DOE.

• BlackBerry Curve 9300 Smartphone won't be using the wifi service

  So I'm not the first person to have this problem.  I've been trawling the web looking for solutions, but nobody seems to have any.

  The problem is that my Curve 9300 won't use wireless instead of data network services.  I can connect to wifi fine networks.  The phone searches for networks, connects, puts a little icon on the home screen saying that it is connected to a wifi network.  It lists the name of the network to the top.  Everything is great, except that when you actually use the internet, the phone connects to your data instead of wifi services and you get charged data consumption.

  If you disable network services to try to force the phone to connect to the wifi instead, you get the error message:

  "You are not currently in an area that can handle the communication of data.  Therefore, the browser can't retrieve all of the web pages.  Please try again when you are in a different location, or contact your service provider if the problem persists. »

  To confirm:

  My Data Services are on.

  My APN settings are disabled.

  In Advanced Options, my default browser Configuration is set to Hotspot browser.

  In General Properties, the default browser is Hotspot browser.

  In the Configuration of the browser, the browser is configured to AT & T Mobile Web.  I tried to change it to Hotspot browser but I save the changes and exit the screen, then when I go back to check, it's at AT & T.  It's not save the changes to make the default Hotspot.

  I did a battery pull to see if that would help and after restarting it allowed me to keep the Hotspot as the default configuration but it would not connect if the mobile service has been disabled.  He is now back himself to AT & T and still does not work.

  I read the thread on the forum "BOLD", but for all the people complaining having the same problem, there is still no solution.  I really want a resolution to this because I do a lot of travel and my card sim may not always connect to a local network.  I want to be able to go to a local coffee shop and be able to connect, even if I don't have telephone service in a foreign airport.  I don't understand what is the point of having wifi on a phone if you can't use it.

  OS 6 is available for BlackBerry 9300, please connect to www.blackberry.com and download the latest software from the support section device, install it on your PC and then connect a device with PC by using the USB cable and check for update of the device.

• BlackBerry Curve 9300 Smartphone does not start. Stucks at the splash screen

  Hello

  I have a brand new Curve 9300, and within a week he is a. I updated its OS to version 6, and it worked perfectly.

  When I tried to configure my email, he asked automatically updated with the installation of my e-mail service provider software. I chose just ok. I received three warning messages, which I don't know exactly but it was something may not work correctly (with respect to the difference in version). I just kept facility, and he asked to reset.

  When I restarted the laptop, it goot stuck to the start screen. Then nothing! The thin status bar below fills BlackBerry logo until either full, nothing happens. When I wait more long (a few minutes), I get a message on a white screen with a small font with "App Error 606", with an option to "RESET".

  I took out the battery and restored a few times, nothing different.

  Notes:

  • The LED does nothing, except for a single red wink when it restarts
  • The keboard seems to be sensitive. I get the Alt and shift indicators at the top right when I press on the
  • The power button does not appear to cause any response

  I appreciate your help.

  Edit: Desktop software indicates that the device is not connected, even if it is attached to the USB cable.

  Edit: The combination Alt + Shift + Delete causes the system to go to a blank white screen with this "app" error mentioned above

  You use BBSAK or JL_Cmder to wipe the device and then load the operating system on the device. Follow the instructions here:

  http://www.BlackBerryFAQ.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F

• BlackBerry Curve 9300 Smartphone update

  Your carrier: Airtel

  Model information and the version of the OS (go to settings, then Options, then): v6.0.0.706

  Can someone please tell me who is the latest OS for curve 9300 3 and how do I put to it with step by step instructions. I am new to Blackberry Upgradation and all.

  Hello and welcome to the community!

  The easiest way is, on a PC (you can not do on MAC):

  (1) make sure that you have a current backup and your BB complete... you can find the instructions at the link in my auto-sig below.

  2) uninstall all the BB OS packages from your PC,

  (3) make sure you have the BB Desktop Software already installed

  • http://us.BlackBerry.com/software/desktop.html

  (4) download and install on your computer, the BB OS package you want:

  • http://us.BlackBerry.com/support/downloads/download_sites.jsp
  • If all you want are the levels of BONE, it is first sorted by carrier - the carrier supports, your search will be fast. However, some carriers are much slower than others to release updates. To really get the package up-to-date OS for your BB, you need to dig through and find all businesses that support your specific model BB and then compare the BONE levels they support.
  • Find out who is the 'last' is difficult, however. Each carrier controls the release of the OS to their customers, but some carriers do they not release what they receive from BB. Yes, 'later' is a matter of company by company, not a universal.

  5) remove all copies of the SELLER on your PC. XML... There will be at least one and maybe 2, and they will be located in the same way or to (it changes based on your version of Windows) these files:

  • C:\Program Files (x 86) \Common Files\Research In Motion\AppLoader
  • C:\Users\(your Windows username) \AppData\Roaming\Research In Motion\BlackBerry\Loader XML

  6 (a) to change your level of BB OS installed (at level or lower), you can run the Desktop software and connect your BB... the software should offer the operating system package you have installed on your PC.

  6 (b) or, for recharging your BB OS level installed as well to change, work around the Desktop software and use the CHARGER. EXE directly, through step 2 in this process:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-device-software/how-to-reload-your-operating-syste...
  • Note Although written to "recharge" and the storm, it can be used to upgrade, downgrade or recharge any BB device model - depends on the operating system package you download and install on your PC.

  If, during the process of 6a or 6 b, your BB has an error '507', simply unplug the USB of the BB cord and reinsert it. do nothing else... This should allow the installation to continue.

  If you are on a MAC, you are limited to only your sanctioned carriers OS packages... but can still use any level they currently have to sanction. See this procedure:

  • KB19915 How to perform a clean reload of the smartphone BlackBerry using BlackBerry Desktop Software application software

  Good luck and let us know!

• BlackBerry Curve 9300 Smartphones mail

  Hello. I installed the new software for the Curve 9300. When I go into the configuration page to configure my email, it allows me to select the email icon. When I go to the mail icon in the main menu, it says "no message services configured. You will be redirected to the Setup Wizard to install your e-mail account '.' When I click ok, it opens a blank message template. Can anyone help? Thank you

  Using your browser, go to mobile.blackberry.com

  Scroll to the bottom to Communications, and then to the Email.

  Select your type of e-mail that you want to configure and set up there.

• HP Officejet 5740: disconnects from the network

  IMac El Capitan & Airport extreme router

  Printer will connect and stay connected while Mac is turned off.

  Turn on the Mac and the wireless connection is lost

  In some cases "impossible to find the network" in others, bad IP address.

  Have you tried wiring printer to the router (ethernet USB) same results

  Also tried hard wiring for Mac

  and finally no. son... basically all with the same results.

  Have tried all the suggestions reboot router, Mac, printer...

  Connects and disconnects...

  Need help

  I wanted to leave you hanging...

  Contacted Comcast and said that my modem is too old and it to replace.

  Now, I have a new modem/wifi combo and everything works.

  It reminds me of the guy who bought a button of his jacket and ended up having to buy a new jacket for the button!

  In any case thank you for your patience, and all's well that ends well.

• Get the latest data of Variable shared before disconnecting from the network

  Hello.

  I use Shared - published network variables for my communication between two PC's. Each LV software will pass the data to another.

  Sometimes the wireless connection to become really bad and the network connection stops.

  I want to get the latest data. Currently my VI will show the value '0' on the variable shared data once the connection is cut.

  I tried using shift, but she registers the same results.

  Can someone show me how I can stay past data when the network connection is disconnected.

  Thank you very much.

  Kind regards

  Hello Fan, Ravens

  It works! Thank you very much.

  Kind regards

• Connection Wi - Fi Windows guard disconnect from the network.

  We went from ISPS to Fios a few weeks ago and my dad's computer is having issues staying connected to the Wifi network. It is running win XP Edition family. It works for about 10 minutes until it is "Impossible to connect to preferred wireless network. When I opened the network available to try to reconnect, it does not work. It says "waiting for network" but never connects. Then I hit cancel and have to make my way to the properties of internet protocol tc/pic, then click OK, and it connects to the network for 10 minutes. Rinse and repeat. But the trick is before you go to properties of internet protocol, I have TO let it fail in the connection to the network is available.

  Another thing, if I have it configured to obtain an IP address and DNS of the server automatically, it is stuck on the 'acquisition of network address' forever. never connects. I have to manually set the IP address and DNS servers of the internet to work for 10 minutes... then the above questions.

  I have no idea how to solve this problem, then the internet will only work! Help, please!

  Hi patoons,

  · What is the number and the model of the computer?

  · What is the service pack installed?

  · You have security software installed on the computer?

  Follow the methods below:

  Method 1:

  Disable security software and firewall temporarily on the computer and then try to connect to the internet.

   

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:

  Follow the steps from the link below: Troubleshooting network connection problems:http://www.microsoft.com/windowsxp/using/networking/maintain/troubleshoot.mspx

  Method 3:

  Also, try to reset the TCP/IP Protocol and check the results: how to reset the Protocol (TCP/IP) Internet:http://support.microsoft.com/kb/299357

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• BlackBerry Curve 9300 Smartphone keeps transmitting a soon exhausted battery data

  I'm running a Curve 9300 that I sync with both my desktop PC on Lotus Notes and my PC at home on Outlook 2010.

  When data transmission is enabled, I can see on-screen units continues to go to trasmit/reception and become quite meaningless. Battery turns off quickly.

  I can use it as a phone plin keeping disabled data transmission.

  Can anyone help?

  Thank you!

  Let me you a friend to watch it.

  I would suggest first off backup and wipe the unit with a cloth of security and get then added to the BES.