Blank CD is not recognized in a Qosmio G10 124

Similar Questions

• Expand battery qosmio g10 124

  I need an extra Baterry my g10-124. Oheard there's an akkupack where I can just take my dvd player and just put in some kind of battery that expands battery working time!
  (1) anyone know something?
  (2) what type of second battery buy for my g10-124? I know it's the Li - ion battery but what type?

  Hello

  Sorry, but know there is no extra battery for this camera. Some units have an extra-large battery or select Bay components but not Qosmio. DVD player is fixed mounted and there is no way to put a battery inside.

• Qosmio G10 124: GPU overheating if disabled tuner

  My G10-124 with: replacement card with nvidia go6600 and 915 PM Chipset works well.

  But if I disable Tuner, to get more autonomy the fan doesn't work properly and the GPU gets over-heated (> 100 degrees).

  Does anyone know about this problem and a way to get the Fans work properly?

  What is the Tunerdeactivation effect? I can't understand.

  I found your other thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=50736

  Seems that you have updated the DMI himself. This could affect the BIOS information and info table cooling in the BIOS.
  This can affect the performance of the cooling modules and can lead to the highest temperature

  Second reason could be the use of non-Toshiba graphics cards drivers
  3rd party drivers graphics don t support protection against overheating and this leads to better GPU performance and at a higher temperature

  What I recommend to check the unit by an ASP. Guys should take a peek at the DMI information.

• Qosmio G10-105: standard VGA need driver for Vista

  Hello

  I want software for standard VGA graphics adapt nVIDIA GeForce Go 6600 for Vista

  Please help me

  I put t know what you mean by software for standard VGA graphic card, but I guess you a looking for a driver for Vista graphics card.

  Unfortunately, Vista is not supported on the Qosmio G10 and F10 series and therefore a graphics driver doesn t exist on the driver page.

• Camera connected DV Firewire/IEEE 1394 is not recognized - Qosmio F20

  Hi - I wonder if anyone has any advice on the following points.

  I have a Qosmio F20 running XP Media Center.
  I have a JVC GR-DVM5 (old but good) camcorder with an i.Link/1394 port. Connecting a DV camera to the PCs 1394 port via a firewire cable 4 pin should recognized the camera as a device of additional hardware and install automatically.

  However, the device is not recognized. Even try to be creating the device in applications such as Movie Maker, WinDVD creator, etc., does not work and the unit is not picked up by these.

  All things were created according to the JVC user manual, the 1394 port works well (depending on Device Manager), and the driver is up-to-date.

  According to Microsoft, the appropriate drivers are included in XP (http://support.microsoft.com/kb/300459/en-us - but still MS have failed to confirm to me that this applies to XP MCE as well as professional and Home editions.)

  Can anyone provide any help! ??

  JB

  It is the right word. I have connected my older Sony camcorder via firewire to Qosmio G20 and the camcorder is recognized correctly (Sony cam was listed in Device Manager). I was able to copy all saved on the HARD drive movies and create DVDs later.

  Believe me it's very interesting that all devices Sony I have connected with Qosmio laptop computer were recognized correctly (two camcorders different and two digital cameras). I really don't understand what's wrong with your JVC cam.

  I ve checked a digital video forum and a guy with the same problem reported that he was able to connect the cam when the cam is placed in the docking station. Can you please try the same thing?

  Of course, the cam must be turned on.

• Re: Qosmio x 770-107 - recovery disk not recognized

  I gave up my old 3 months Qosmio x 770-107 last week and killed my HARD drive. A new HARD disk, exact replacement to order it. Ordered a DVD of recovery of this backup media site that is posted here. I entered number etc.

  Rolled up today but at the start it is not recognize at all. He sees my drive in the BIOS, and I changed the startup as well as preferences to try waiting usual f12 or whatever.

  All I get is:
  "Reboot and select proper boot device."
  Or insert boot media in selected boot device and press a key. »

  It doesn't matter what I do.

  I tried another windows 7 boot cd and it started to load files perfectly. It's infuriating after 8 days of waiting, I thought I was back in business.

  Any help?

  Thank you

  Chelm.

  Post edited by: chelmdog

  > I tried another windows 7 boot cd and it started to load files perfectly.

  This means that you can install Win7 using the original installation disc from Microsoft but Toshiba recovery disc is not recognized at all?

• Qosmio F50 - 12L - multimedia controller not recognized on Windows 7

  Qosmio F50 - 12L

  Drive multimedia controller is not recognized after installing Windows 7 64 bit instead of Windows Vista Ultimate Edition, and my keyboard is not brightening under buttons.

  I put t know what to do.
  Please send me the answer.

  HI ladybob78,

  Can you please tell us what you mean with multimedia controller?
  What device do you mean?

  In regards to illumination buttons, you need to install Toshiba Value added Package, and Flash Cards Support utility. These two tools should be released for Windows 7.

  Here's a similar thread about Windows 7 and Qosmio F50:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=47658&TSTART=0

• Blank DVDs does not get recognized when you try to burn DVDs.

  Original title: CD/DVD/player burner needs help

  My laptop cd/dvd drive / burner, he is no acknolwedge a blank dvd, but it will be a blank cd, it will also play both, im trying to burn a dvd, but it is not acknowling that one is in the burner, it was working fine yesterday... Please help

  Hi PatriciaKnight,

  ·         You get the error message?

  ·         What application are you using to burn on DVD?

  ·         Remember to make changes to the computer, after which the issue started?

  I suggest you try the following Microsoft Fixit and/or the steps from the following links in the article and see if it helps:

  Your CD or DVD drive cannot read or write media

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  I hope this helps.

• The Z10 blackBerry Getting counter messages: "this tag is blank or not recognized.

  Hi all
  I started getting messages 'this tag is blank or not recognized' continuing on my screen. They appear every few seconds, accompanied by a vibration.
  He started out of the blue as I wasn't even using the device. I re-started, but it does not help.
  Someone knows what to do?
  Thank you!

  I had seen this happen to someone - who had stuck a card of NFC in their case... The BlackBerry kept reading the card (which was empty)...

• I just replaced my cd/dvd drive with a new TEAC one. I have Vista (32-bit) but iTunes Windows Media players, it is not recognized as a burner and won't read blank media. I need help!

  TEAC DV - 28 S - W model number

  Hello

  Try these steps and see if it helps.

  Step 1: Run the provided article fixit.

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Step 2: Run the troubleshooter of CD/DVD burning.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-and-burning-CDs-DVDs-and-BluRay-discs-Troubleshooter

  For ITunes:

  http://support.Apple.com/kb/ts1436

  See also:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

• Solution: The USB floppy drive is not recognized during installation of XP of RAID

  Hello

  This Solution is for notebooks Qosmio with RAID driver during (manual installation of windows)

  I found the Solution to this problem,

  [When you install Microsoft Windows XP by using a floppy drive USB on a player who]
  requires a driver during the installation, the USB floppy drive is not recognized in all
  installation. When Windows XP searches the driver of the second time, he will not be able to see
  the floppy USB drive drive and prompts the user for the driver (RAID) again.
  The installation will never reach this point. ]

  Solution:

  This is a limitation of Microsoft, the Floppy Drive are do not appear in the file Windows 'txtsetup.sif.

  Simply change the floppy drive in another brand and avoid Usb 2.0 external Usb floppy plus old 1 Try
  Also note the back of drive sometimes they write (no bootable) avoid this also

  I personally Test this and it does not work it is "IBM Portable floppy drive" drive silver
  P/N 27L 4226, FRU P/N 05K 9283 TEAC CORPORATION MODEL NO. FD-05PUB

  The following USB floppy drives are listed in the file "txtsetup.sif" and are supported:

  Device ID = VID: 057B and PID: 0000 for external floppy USB SONY drive, Sony 09K 9835 part number

  Device ID = VID: 0644 and PID: 0000 for floppy drive to the external USB, TEAC, IBM replacement part number (FRU) 13N6752

  USB\VID_03EE & PID_6901; Mitsumi USB floppy drive

  USB\VID_057B & PID_0000; Floppy drive USB YEData, Sony part number 09K 9835

  USB\VID_0644 & PID_0000; Floppy drive USB TEAC 27L 4226, FRU 05K 9283 IBM option part number

  The following USB floppy drives are not listed in the txtsetup.sif file and are not supported:

  USB\VID_03F0 & PID_2001; HP
  USB\VID_054C & PID_002C; Sony
  USB\VID_057B & PID_0001; YEData
  USB\VID_0409 & PID_0040; NEC
  USB\VID_0424 & PID_0FDC; SMSC

  If you want manual of Installation of Windows Xp Media Center Edition 2005
  then check out my discussion here

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=16498

  Thank you for the very interesting topic.
  I think that it s an enemy of information all of you who have the same problem.

  Thanks ;)

• Device not recognized USB error message - all USB ports.

  Apologies if all this seems a bit simple, but I'm not an expert, so bear with me.

  I have a laptop Fujitsu Siemens Amilo Li 1718.

  My USB ports have stopped working in 2-3 weeks.  I get the message "USB device not recognized.  One of the devices attached to this computer has malfunctioned and Windows does not recognize... »

  I don't seem to get any yellow exclamation point in device, all my drivers in Device Manager and software are up to date and Windows Update is running.

  My mobile phone and ipod always charge when I plug them in and out of this problem, everything works fine.

  In addition to the usual updates of Windows, only two other things have occurred since last, they worked.  One was that I renewed my subscription to Norton Antivirus, the other was that my laptop battery ran right out while he was in mode 'sleep' as I did not know that I had not plugged to the socket properly.

  So far, I went through some process as suggested by various items and/or help & support on Microsoft.com.  They include:

  * (From multiple locations) system restore has failed.
  * Diagnostic software Ran Fujitsu Siemens, which says that my computer is fine.
  * Run the virus scan who come clean.
  * Tries to connect via a USB hub.
  * Deletied the USB controllers in Device Manager to re - install.
  * Changing the settings of ForceHcResetOnResume 3-to-1
  * Change AdditionalCriticalWorkerThreads from 0 to 2

  (The last two I've changed back again after neither worked).

  My opinion of beginner, it's that looks like it will create new registry details for each device when valid seem to exist already is not thankful.  Although given my lack of technical knowledge, this could well be stating the obvious.

  So, now, I drew a blank.  Anyone got any ideas?  Got 9 months left a 3-year warranty, I don't want to go through the hassle if it can be avoided without too much trouble.

  Thanks in advance!

  Tim

  Hello

  Maybe these will help.

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or does not work - a Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Have you tried to use an external hub powered by USB power is very limited in a computer and if overloaded
  strange problems will come up.

  ------------------------------------------

  Even if you did some of this departure please up and work until low and if necessary check
  with the utility.

  Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices

  Now look everywhere EXCEPT the USB controllers for your device (cannot be found) and if you find
  It RIGHT CLICK and UNINSTALL all. The device is your (s) or similar.

  now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.

  APPLY/OK

  RESET

  This refresh battery USB and hopefully it will allow the unit to install. (You may need a powered hub)

  Here is the similar procedure under XP, Vista is the same, except that we need to clear the specific device if present.
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all
  USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
  Try to remove all instances and restart then plug the drive.
  http://www.NirSoft.NET/utils/usb_devices_view.html

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Can't burn a cd. The music is not recognized.

  I can't burn an audio cd. The Player recognizes my blank cd, and it says I have 79:57 minutes to burn. But when I add music to the burn list, I always 79:57 free minutes. The music is in the burn list, but I can't start a burn because the music is not recognized. Can someone respond to this please?

  I don't know what I did, but as soon as I played the music button "Start burn" is now available. I didn't understand why the music was not recognized in the burn list because yesterday I did the same thing and I had no problem, but knowing that everything is the same. The music was compatible and the burner has not been damaged, so I guess it was just a temporary system problem. Thanks for answer and sorry for wasting your time :)

• Windows login password not recognized

  Original title: sign the password not recognized.  Similar problems are are produced.

  Already happened.  Tried to sing in password rejected.  It's the same thing and I him have not changed for a long time.

  Log on to another administrator user account and change your password to something that you will remember. Then search for malicious software because these things do not happen by themselves. Or think about who else has access to your computer and may have changed your password without your knowledge.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  If you have another administrative user (see Configuring user recommended at the end of this post) and then you have to activate the built-in Administrator, and then change the password of your user account. All this requires a certain level of computer skills. You know better and that take the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best solution for you.

  If you have a Windows 7 DVD installation (not a recovery DVDs), you can start the system with it. Select the default language, then select "repair your computer". Then select "Command Prompt". At the command prompt, type:

  NET user administrator / Active: Yes [press Enter]
  NET user [insert here the name of your user account] [insert the new password of user as 1234 here] [press Enter]

  [Note: do not enter the brackets!]

  Remove the installation DVD and restart the computer. Now, you will be able to connect to your user account by using the password that you set; for example, 1234.

  If you do not have a Windows 7 installation DVD (only have a recovery disk), the computer mftr. may have given you the option to repair the system Windows 7 (not a system recovery!) in the menu diagnosis. This menu of diagnosis is the same one where you can choose Safe Mode. Get to this menu by repeatedly pressing the F8 key as the computer starts. If you do not have this option, you can make a bootable DVD of Windows 7 repair of the file on this link:

  http://NeoSmart.net/blog/2009/Windows-7-system-repair-discs/

  Note: All the Neosmart recovery disk downloads are torrent files. There is a good explanation of the torrent on the site Web of Neosmart files. You will need a torrent asmuTorrent client to get the files. Torrent client will download the .iso file with which to create the bootable DVD. If you create the bootable DVD in an older operating system (XP, Vista), you will need to use third-party burning software such as Nero, Roxio or the free ImgBurn (http://www.imgburn.com ) to burn the image .iso image file, not in the form of data. Windows 7 can burn the .isos natively.

  Once you have fixed things, log on to the additional administrative account you will be made by the suggestions below and disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  Exit the command prompt.

  General recommendations for creating users in Windows 7:

  You absolutely don't want to have only one user account. Like XP, Vista and all the other modern operating systems, Windows 7 is a multi-user system with integrated system of accounts as default Administrator and comments. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want account only one user with administrator privileges in Windows 7 because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult.  It is not impossible to activate the built-in administrator to rescue things, but there may be more that you want to do. Better not to put you in a bad situation at first.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. As a user Standard is recommended for security reasons and will help protect your computer against infections. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  MS - MVP - Elephant Boy computers - don't panic!

• iTunes not recognizing iphone

  Hey guys, last updated itunes is not recognizing my iphone.

  Uninstalled and reinstalled iTunes several times, everything is up to date. I also tried the thing of driver device manager update, but the apple usb driver is not present even after I have reinstall and uninstall iTunes, all solutions? p.s Also running windows 10.

  Hello, you should see this article, it will help you If iTunes does not your iPad, iPhone or iPod - Apple Support