Blocking remote - site-to-site vpn network
Hello
I have a VPN site-to site already set up, everything works as it should. I'm trying to block remote network access to our network as we only need access to them. I'm sure it's something very easy to implement with an ACL, but I don't know where this rule should go. The VPN is on ASA 5505.
Example:
1.1.1.0/24 - local area network - site has
Site B - remote network - 2.2.2.0/24 - want to block this local access network
Any help or advice would be appreciated.
Thanks in advance,
-j
You are right.. ACL is the best way to go.
You can configure ACLs in the outbound direction of the internal interface as follows:
inside-acl-out of ip 2.2.2.0 deny access list 255.255.255.0 1.1.1.0 255.255.255.0
inside-acl-out the ip access list to a range
Access-group inside-acl-out interface
With the above ACL, it crashes all the traffic from the remote VPN to the internal interface while allowing the rest (for example: were other interfaces of the ASA) originally from connection to the internal network.
I hope this helps.
Tags: Cisco Security
Similar Questions
-
problem with users to access remote vpn site to site vpn network
I did the Setup: asa 5510 configured remote access vpn. My vpn users receive asa 5510 range 192.168.50.0/24 addresses and users access my local lan 192.168.0.0/24. the second side of the local lan 192.168.0.0/24 on asa 5505, I did a vpn site-to-site with network 192.168.5.0/24.on that both sides of a site are asa 5505. inside the interface asa 5510 Elise 192.168.0.10 and inside the interface asa 5505 have address 192.168.0.17.third asa 5505 networked 192.168.5.0/24 address 192.168.5.1. I want my remote access vpn users can access resources on network 192.168.5.0/24. I create the static route on inside the asa 5510 static route 192.168.5.0 interface 255.255.255.0 192.168.0.17 and a static route on inside the asa 5505 static route 192.168.50.0 interface 255.255.255.0 192.168.0.10, but it's not working. What do I do?
execution of the configuration of my asa 5510 is
Result of the command: "show run"
: Saved
:
ASA Version 8.4(2)
!
hostname asa5510
domain-name dri.local
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.178 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.0.10 255.255.255.0
!
interface Ethernet0/2
description Mreza za virtualne masine- mail server, wsus....
nameif DMZ
security-level 50
ip address 172.16.20.1 255.255.255.0
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name dri.local
object network VPN-POOL
subnet 192.168.50.0 255.255.255.0
description VPN Client pool
object network LAN-NETWORK
subnet 192.168.0.0 255.255.255.0
description LAN Network
object network NETWORK_OBJ_192.168.0.0_24
subnet 192.168.0.0 255.255.255.0
object network 192.168.0.10
host 192.168.0.10
object service ssl
service tcp destination eq 465
object service tls
service tcp destination eq 995
object network mail_server
host 172.16.20.201
object service StartTLS
service tcp destination eq 587
object service admin_port
service tcp destination eq 444
object service ODMR
service tcp destination eq 366
object service SSL-IMAP
service tcp destination eq 993
object network remote
host 172.16.20.200
object network test
host 192.168.0.22
object network mail
host 172.16.20.200
object network DMZ
host 172.16.20.200
object network Inside_DMZ
host 192.168.0.20
object service rdp
service tcp destination eq 3389
object network DRI_PS99
host 192.168.0.54
object service microsoft_dc
service tcp destination eq 445
object service https448
service tcp destination eq 448
object network mail_server_internal
host 172.16.20.201
object service Acronis_remote
service tcp destination eq 9876
object service Acronis_25001
service tcp destination eq 25001
object service HTTP3000
service tcp destination eq 3000
object network VPNPOOL
subnet 192.168.50.0 255.255.255.0
object-group network PAT-SOURCE-NETWORKS
description Source networks for PAT
network-object 192.168.0.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object admin_port
service-object object ssl
service-object object tls
service-object object https448
object-group service DM_INLINE_SERVICE_2
service-object object admin_port
service-object object https448
service-object object ssl
service-object object tls
service-object tcp destination eq pop3
service-object tcp destination eq smtp
object-group service DM_INLINE_SERVICE_3
service-object object admin_port
service-object object https448
service-object object ssl
service-object tcp destination eq smtp
service-object object tls
service-object object Acronis_remote
service-object tcp destination eq www
service-object object Acronis_25001
service-object object microsoft_dc
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
object-group service DM_INLINE_SERVICE_4
service-object object Acronis_25001
service-object object Acronis_remote
service-object object microsoft_dc
service-object tcp destination eq www
service-object tcp
service-object ip
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 any object mail_server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any object mail
access-list Split_Tunnel_List extended permit ip 192.168.0.0 255.255.255.0 any
access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 192.168.5.0 255.255.255.0
access-list DMZ extended permit object-group DM_INLINE_SERVICE_4 172.16.20.0 255.255.255.0 any
access-list DMZ extended permit object-group DM_INLINE_SERVICE_3 host 172.16.20.201 any
access-list DMZ extended permit object-group DM_INLINE_PROTOCOL_1 172.16.20.0 255.255.255.0 any inactive
access-list DMZ extended deny tcp any any eq smtp
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
ip local pool vpnadrese 192.168.50.1-192.168.50.100 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN-NETWORK LAN-NETWORK destination static VPN-POOL VPN-POOL
!
object network mail_server
nat (DMZ,outside) static x.x.x.179
object network mail
nat (DMZ,outside) static x.x.x.180
access-group outside_access_in in interface outside
access-group DMZ in interface DMZ
route outside 0.0.0.0 0.0.0.0 178.254.133.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action terminate
dynamic-access-policy-record dripolisa
aaa-server DRI protocol ldap
aaa-server DRI (inside) host 192.168.0.20
ldap-base-dn DC=dri,DC=local
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=dragan urukalo,OU=novisad,OU=sektor2,OU=REVIZIJA,DC=dri,DC=local
server-type microsoft
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
virtual telnet 192.168.1.12
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 195.222.96.223
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.0.14-192.168.0.45 inside
!
dhcpd address 172.16.20.2-172.16.20.150 DMZ
dhcpd dns x.x.x.177 interface DMZ
dhcpd auto_config outside interface DMZ
dhcpd option 6 ip x.x.x.177 interface DMZ
dhcpd enable DMZ
!
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
!
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy GroupPolicy_x.x.x.223 internal
group-policy GroupPolicy_x.x.x.223 attributes
vpn-tunnel-protocol ikev1 ikev2
group-policy drivpn internal
group-policy drivpn attributes
dns-server value 192.168.0.20 192.168.0.254
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-tunnel-protocol ikev1 l2tp-ipsec
split-tunnel-network-list value Split_Tunnel_List
default-domain value dri.local
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group drivpn type remote-access
tunnel-group drivpn general-attributes
address-pool vpnadrese
authentication-server-group DRI
default-group-policy drivpn
tunnel-group drivpn ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group x.x.x.223 type ipsec-l2l
tunnel-group x.x.x.223 general-attributes
default-group-policy GroupPolicy_x.x.x.223
tunnel-group x.x.x.223 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect tftp
inspect ip-options
inspect netbios
inspect icmp
inspect http
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:69c651e94663fc570b67e0c4c0dcbae1
: endrunning config asa 5505
Result of the command: "show run"
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password csq7sfr0bQJqMGET encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.5.0 PALATA
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
object-group service DM_INLINE_SERVICE_1
service-object ip
service-object tcp
service-object icmp echo
service-object icmp echo-reply
service-object tcp eq domain
service-object tcp eq ldap
service-object tcp eq smtp
object-group service DM_INLINE_SERVICE_2
service-object ip
service-object tcp eq domain
service-object tcp eq www
service-object tcp eq https
service-object tcp eq smtp
object-group service Sharepoint8080 tcp
port-object eq 8080
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any any
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_2 192.168.0.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list outside_2_cryptomap extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
pager lines 24
logging enable
logging asdm informational
logging mail errors
logging from-address
logging recipient-address level debugging
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 192.168.0.0 255.255.255.0
static (inside,outside) 10.13.74.35 192.168.0.22 netmask 255.255.255.255
static (inside,outside) 10.13.74.34 192.168.0.20 netmask 255.255.255.255 dns
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.13.74.1 1
route inside 0.0.0.0 0.0.0.0 192.168.0.17 tunneled
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication telnet console LOCAL
http server enable
http 10.13.74.0 255.255.255.0 outside
http 192.168.0.0 255.255.255.0 inside
http 10.15.100.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
virtual telnet 192.168.0.53
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_2_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 10.15.100.15
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group 10.15.100.15 type ipsec-l2l
tunnel-group 10.15.100.15 ipsec-attributes
pre-shared-key *
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
!
service-policy global_policy global
smtp-server 173.194.79.109
prompt hostname context
Cryptochecksum:4767b6764cb597f0a7b8b138587d4192
: endThank you
Hello
I have previously edited the my initial response was in fact not necessary since you were actually using full Tunnel
EDIT: Actually just noticed the the VPN client isnt using Split Tunnel. Its Full Tunnel at the moment since it doesnt have the "split-tunnel-policy tunnelspecified"
So you don't really have any of those.
Please mark the question answers and/or assess response
Ask more if necessary
-Jouni
-
Hello
I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.
We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem
(NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)
Internally, we have a full mesh VPN, so all offices can talk to each other directly.
I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.
I was able to run for the Office of CT, but I can't seem to work for the Office of the NC. (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).
Someone could take a look at these 2 configs and let me know if I'm missing something? I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there
PA OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname WayneASAnames of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 70.91.18.205 255.255.255.252
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
75.75.75.75 server name
75.75.76.76 server name
domain 3gtms.com
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
inside_access_in of access allowed any ip an extended list
IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside-nat0
inside_access_in access to the interface inside group
Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 98.101.139.210
card crypto IPSec_map 2 the transform-set VPNTransformSet value
card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
IPSec_map interface card crypto outside
card crypto outside_map 1 match address outside_1_cryptomap
peer set card crypto outside_map 1 50.199.234.229
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 60
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.100 - 192.168.1.199 inside
dhcpd dns 75.75.75.75 75.75.76.76 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RemoteTunnel group strategy
attributes of Group Policy RemoteTunnel
value of server DNS 75.75.75.75 75.75.76.76
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
dfavier vUA99P1dT3fvnDZy encrypted password username
username dfavier attributes
type of remote access service
rduske vu0Zdx0n3oZWFSaX encrypted password username
username rduske attributes
type of remote access service
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
lestofts URsSXKLozQMSeCBk username encrypted password
username lestofts attributes
type of remote access service
jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
username jpwiggins attributes
type of remote access service
tomleonard cQXk0RJCBtxyzZ4K encrypted password username
username tomleonard attributes
type of remote access service
algobel 4AjIefFXCbu7.T9v encrypted password username
username algobel attributes
type of remote access service
type tunnel-group RemoteTunnel remote access
attributes global-tunnel-group RemoteTunnel
address pool VPNPool
Group Policy - by default-RemoteTunnel
IPSec-attributes tunnel-group RemoteTunnel
pre-shared key *.
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 98.101.139.210 type ipsec-l2l
IPSec-attributes tunnel-group 98.101.139.210
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
: endCT OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname RaleighASA
activate the encrypted password of Ml95GJgphVRqpdJ7
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
192.168.5.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 98.101.139.210 255.0.0.0
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS server-group DefaultDNS
Server name 24.25.5.60
Server name 24.25.5.61
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
out_access_in list extended access permit tcp any host 98.101.139.210 eq www
out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
out_access_in list extended access permit tcp any host 98.101.139.210 eq https
out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto IPSec_map 1 corresponds to the address Wayne_Access
card crypto IPSec_map 1 set pfs Group1
card crypto IPSec_map 1 set peer 70.91.18.205
card crypto IPSec_map 1 the transform-set WayneTransform value
card crypto IPSec_map 2 corresponds to the address Shelton_Access
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 50.199.234.229
card crypto IPSec_map 2 the transform-set SheltonTransform value
IPSec_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.5.100 - 192.168.5.199 inside
dhcpd dns 24.25.5.60 24.25.5.61 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 70.91.18.205 type ipsec-l2l
IPSec-attributes tunnel-group 70.91.18.205
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
: endHello
I might have found the problem.
To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.
At the moment it seems to me that this configuration is the problem on the SITE of PA
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
This is an ACL that defines networks the and remote for a connection VPN L2L.
Now, when we look at what connection VPN L2L this belong we see the following
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?
Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site
Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.
So can you remove this line ACL of the ASA of PA
No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
Then, test the VPN Client connection NC SITE again.
Hope that this will finally be the solution
-Jouni
-
Cannot ping computers on the subnet remote site vpn while to set up
Hi all
I encountered a problem of site to site vpn for ping answered nothing of machines of remote subnet.
the ipsec tunnel is ok but I can ping the ASA distance inside the interface ip
Here is my scenario:
LAN1 - ASA5510 - ASA5505 - LAN2 - ordinateur_distant
LAN1: 192.168.x.0/24
LAN2: 172.25.88.0/24
remote_machine_ip: 172.25.87.30
LAN1 can ping to ASA5505 inside interface (172.25.88.1)
but cannot ping ordinateur_distant (172.25.87.30)
Inside of the interface ASA5505 can ping ordinateur_distant
LAN2 can ASA5510 ping inside the machines on LAN1 and interface
Is there something I missed?
Thanks much for the reply
I don't think it's something you really want to do.
If you PAT the whole subnet to LAN1 ip (192.168.1.0/24) to 172.25.249.1, then LAN2, will not be able to reach the specific host on LAN1, cause now, you represent the LAN1 network, with a single ip address.
So traffic will become a way from LAN1 can reach LAN2 and get the response of LAN2 through the PAT on 172.25.249.1
But LAN2, is no longer specific hosts LAN1 ip traffic, since you only have 172.25.249.1, to represent the subnet to LAN1.
If you still want to PAT the whole subnet to LAN1 (192.168.1.0/24) ip to 172.25.249.1, then you have to do outside the NAT.
http://www.Cisco.com/en/us/customer/docs/security/ASA/asa80/command/reference/no.html#wp1737858
Kind regards
-
How to copy tftp on remote site VPN
I know that by the definition of ASA management interface can ping or telnet/SSH to the inside interface of the ASA remote VPN. But it does not work for TFTP. Is it possible to copy config TFP server in a remote site via VPN and using the source as a local within the interface interface?
Your home, remember messages useful rate.
Concerning
-
Cannot ping sub interface from my remote site VPN gateways
I can't ping my gateways to interface my remote vpn connection sub
I can ping 192.6.1.0 network, but can't ping network 192.6.2.0 or 192.6.3.0
When I remote desktop in 192.6.1.20 I can ping all the networks, including gateways to interface sub.
I think that something in my asa is misconfigured or not added
ASA NAT rules:
Exempt NAT Interface: inside
Source 192.6.0.0/16
Destination 192.6.10.96/27
Static NAT interface: inside (it's for the local NAT of E0/0 out)
Source 192.6.1.1/16
Interface translated outside the Destination: 172.35.221.200
Dynamic NAT interface: inside
Source: no
Destination: outside
ASA access rules:
Permit outside
Source: no
Destination: out
Services: udp, tcp, tcp/http
Static routes:
Interface: Outside > network: all outdoors DSL (shows no DSL in the graph)
Some incorrect configuration:
On the ASA:
(1) directions are incorrect, the default should point to the next hop route, that is to say: the internet router: 172.35.221.x, as follows:
Route outside 0.0.0.0 0.0.0.0 172.35.221.x
---> where x must be the router internet ip address.
existing routes need to be removed:
No route outside 0.0.0.0 0.0.0.0 192.298.47.182 255
No route outside 0.0.0.0 0.0.0.0 172.35.209.81 in tunnel
(2) the following declaration of the static NAT is incorrect too and should be removed:
static (inside, outside) USSLTA01_External USSLTA01 netmask 255.255.255.255
--> You can not NAT interface on the SAA itself.
(3) for the SAA within the interface's subnet mask should be 255.255.255.0, no 255.255.0.0. It should be the same as the router interface subnet mask:
interface Ethernet0/1
nameif inside
security-level 100
IP 192.6.1.254 255.255.255.0
(4) on the way to access these sub interfaces subnet on the SAA as follows:
Route inside 192.6.2.0 255.255.255.0 192.6.1.235
Route inside 192.6.3.0 255.255.255.0 192.6.1.235
Route inside 192.6.4.0 255.255.255.0 192.6.1.235
On the router, configure it by default route as follows:
IP route 0.0.0.0 0.0.0.0 192.6.1.254
-
Do not do a ping ASA inside IP port of the remote site VPN L2L with her
The established VPN L2L OK between ASA-1/ASA-2:
ASA-2# see the crypto isakmp his
KEv1 SAs:
ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 1
1 peer IKE: 207.140.28.102
Type: L2L role: answering machine
Generate a new key: no State: MM_ACTIVE
There are no SAs IKEv2
QUESTION: 3750-2, we ping 3750-1 (10.10.2.253) are OK, but not ASA-1 inside port (10.10.2.254).
Debug icmp ASA-1 data:
ASA-1 debug icmp trace #.
trace of icmp debug enabled at level 1
Echo ICMP Internet request: 10.100.2.252 server: 10.10.2.253 ID = 400 seq = 0 len = 72
ICMP echo response from the server: 10.10.2.253 Internet: 10.100.2.252 ID = 400 seq = 0 len = 72
Echo ICMP Internet request: 10.100.2.252 server: 10.10.2.253 ID = 400 seq = 1 len = 72
ICMP echo response from the server: 10.10.2.253 Internet: 10.100.2.252 ID = 400 seq = 1 len = 72
Echo request ICMP 10.100.2.252 to 10.10.2.254 ID = 401 seq = 0 len = 72
Echo request ICMP 10.100.2.252 to 10.10.2.254 ID = 401 seq = 1 len = 72
Echo request ICMP 10.100.2.252 to 10.10.2.254 ID = 401 seq = 2 len = 72
Make sure you have access to the administration # inside
lt me know f This allows.
-
Connectivity to the remote VPN site adjacent networks
Star topology with Corporate office which acts as hub (192.168.1.x) and remote sites connected by relay frames, except for another network (172.16.x.x) in the building served by 3560 switch company.
On my remote site vpn (10.0.1.x) I can ping network 172.16.x.x, but not the 192.168.1.x network. What I'm trying to do is to allow the network traffic remote 10.0.1.x (which connects directly via the VPN network 172.16.x.x) to reach the network 192.168.1.x and vice versa.
I'm sure its a combination of NAT/routing issue I forget.
I'm new to PIX / ASA in general and it's the first vpn L2L I install. If someone can point me in the right direction, I would appreciate it.
Thank you.
It looks like this?
10.0.1.x->-> Corp. ASA L2L tunnel - >->-> 192.168.1.x 3560 172.16.x.x
and that you can currently communicate via the tunnel between 10.0 and 172.16? In order to communicate between 10.0 and 192.168.1, you will need to define this interesting traffic and add it to your crypto and nat exemption acl.
Corp site
extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0
extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0
NAT (inside) - 0 access list
Remote site
access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
NAT (inside) - 0 access list
-
Can also interface with VPN remote site also for another use?
Hi all
An interface used for the remote site VPN on PIX can be used for another function, for example for the smtp server and web publishing?
Thank you!
Best regards
Teru Lei
Yes! of course you can. Just try it.
--
Alexis Fidalgo
Systems engineer
AT & T Argentina
-
ASA Site, Remote Site cannot access DMZ to the Hub site
So I've been scratching my head and I just can't visualize what I what and how I want to do.
Here is the overview of my network:
Headquarters: ASA 5505
Site1: ASA 5505
Site2: ASA 5505
Training3: ASA 5505
All Sites are connected L2L to the location of the Headquarters with VPN Site to Site.
Since the HQ site I can ping each location by satellite, and each satellite location I can ping the HQ site. I will also mention that all other traffic is also correctly.
Here's my number: HQ site, I have a DMZ set up with a web/mail server. This mail/web server is accessible from my HQ LAN, but not from the satellite location. I need allow that.
What should I do?
My second question is that I want for satellite sites to see networks of eachother. I should create a VPN network between sites, or can this be solved in the same way that the question of the DMZ?
I enclose the show run from my ASA HQ
See the race HQ ASA
For the mail/web server that requires access on the remote site VPN tunnels, you must add the servers to the acl crypto, similar to the way you have it for network access. Make sure that both parties have the ACL in mirror. If you're natting from the DMZ to the outside, make sure you create an exemption from nat from the dmz to the outside for VPN traffic.
For the second question, because you have only three sites, I would recommend creating a tunnel from site to site between two satellite sites.
HTH
PS. If you found this post useful, please note it.
-
AnyConnect VPN full tunnel could not access the site to site VPN
I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code.
It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access.
I checked the IP addresses of network anyconnect are part of the tunnel on both sides.
My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this.
Any help would be appreciated.
Here are the relevant parts of my config:
(Domestic network is 192.168.0.0/24,
the AnyConnect network is 192.168.10.0/24,
site to site VPN network is 192.168.2.0/24)
--------------------------------------------------------------------------------------
permit same-security-traffic inter-interface
permit same-security-traffic intra-interfacethe DM_INLINE_NETWORK_1 object-group network
object-network 192.168.0.0 255.255.255.0
object-network 192.168.10.0 255.255.255.0
inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.10.0 255.255.255.0
access-outside group access component software snap-in interface outside
Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
enable SVC
tunnel-group-list activate
internal AnyConnectGrpPolicy group strategy
attributes of Group Policy AnyConnectGrpPolicy
WINS server no
value of 192.168.0.33 DNS server 192.168.2.33
VPN-session-timeout no
Protocol-tunnel-VPN l2tp ipsec svc
Split-tunnel-policy tunnelall
the address value AnyConnectPool pools
type tunnel-group AnyConnectGroup remote access
attributes global-tunnel-group AnyConnectGroup
address pool AnyConnectPool
authentication-server-group SERVER1_AD
Group Policy - by default-AnyConnectGrpPolicy
tunnel-group AnyConnectGroup webvpn-attributes
the aaa authentication certificate
activation of the Group _AnyConnect aliasYour dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this:
global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0
-
A WLC headquarters and Remote Site
Hello
I have a question for the WLC remote deployment.
For the moment, we have the following design:
Head office
-Network 192.168.49.0/24
-WLC 4402 Version 4.2.61.0
-3 x LAP1252
-LWAPP layer 3
-Wep SSID
-Wpa SSID
-Windows PDC with Active Directory, DHCP server and data storage local
-ACS Version 3.2 for RADIUS and RADIUS authentication--> external DB to Active Directory
Remote site
-Network 192.168.50.0/24
-2 x LAP1252
-Wep SSID
-Wpa SSID
-Windows PDC with Active Directory, DHCP server and data storage local
-ACS Version 3.2 for RADIUS and RADIUS authentication--> external DB to Active Directory
Connection between the seat and the Remote Site
-2 Mbit ADSL
The problem is, wireless on the remote site clients get an IP DHCP 192.168.49.0/24 Beach headquarters. Users at the remote site
most of the time only using the local database server in the remote offices. With the actual design connection ADSL 2 Mbit passes traffic hole the
WLC at Headquarters and at the remote site. It works but it is not that efficient.
The problem could be solved with HREAP, but what I think is, that it is not possible to have the same SSID to Headquarters and remote site with different VLAN.
How can I achieve this, the clients at the remote site to connect to the same SSID (wep or wpa), get an ip address from the remote site (192.168.50.0) DHCP server
and the traffic is enabled locally.
I hope that you understand what is the problem.
Thank you in advance for your help!
Yes, putting the HREAP remote access point mode will allow the WLAN even to be available on the access point but the traffic could tip locally to the AP instead of in the tunnel to the controller. After the AP mode HREAP you re so what VLAN you want traffic for each WLAN to immerse on for this AP.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
VPN access to site-toSite to servers of HO with remote site with overlapping network...
Hi all
I have an obligation to create a tunnel vpn site-to-site on ASA 5510 from a remote location to my HO, I have already other site to site tunnels are on the rise and running on the ASA. This is what my remote site got the network address that is part of a subnet used in HO(192.168.10.0/24). My requirement is only my need to access remote site couple of my servers in HO, who is in the subnet 192.168.200.0/24.
Veuileez help how can I achieve this... your advice at the beginning is very appreciated...
Thanks in advance
MikaelHi Salem,
I think the installer at your end is a bit like this:
You want the remote location to access the subnet 192.168.200.0/24 behind the ASA HQ servers. In this case, you can NAT traffic from the remote site to a different subnet when you go to 192.168.200.0/24.
i.e. the 192.168.10.0/24 subnet resemble 192.168.51.0/24 when he goes to 192.168.200.0
This can be done by using political based natting:
permit access-list policy-nat ip 192.168.10.0 255.255.255.0 192.168.200.0 255.255.255.0
public static 192.168.51.0 (inside, outside) access-l policy-nat
In the encryption of the remote side access list, you will have:
cryptoacl ip 192.168.51.0 access list allow 255.255.255.0 192.168.200.0 255.255.255.0 (this is because the remote side will see 192.168.51.0/24 and not the 192.168.10.0/24)
Similarly on the end of HQ the accesslist crypto will be
XXXXX 192.168.200.0 ip access list allow 255.255.255.0 192.168.51.0 255.255.255.0
Please try this and let me know if it helps.
Thank you
Vishnu Sharma
-
only one statement of site-to-site VPN remote network?
Hello
I wonder on in case of site to site vpn, we can define only a single declaration of network for the Branch Office peer network?
If there is a local network to peer site, then, how to set those for the local subnet peer?
Can anyone answer my question?
Thank you.
If I understand your question, wondering how to add a different subnet to an existing site-to-site VPN tunnel?
If that is correct, you can add this network to the crypto ACL of the tunnel at a site. But you have to demolish and rebuild the tunnel before it takes effect.
Once you have added the required configuration, run the following commands to shoot down the tunnel. Do not forget that this disconnects all users on the VPN, so it is best to let users know when you go to so that they are not connected at this time here.
ISAKMP crypto claire
clear crypto ipsec his
Maybe you are looking for
-
I need to move some messages (and nothing else) from an old profile of TB in the new profile. How?
Windows 8.1 New installation of Thunderbird on the new computer. I thought I had migrated correctly the user profile of the old computer, but when I opened TB, the old profile was not in place and 51 messages downloaded in the new default profile. I
-
Aiport Extreme randomly disconnects wireless and Internet.
My AirPort Extreme 5th generation disconnects wireless and Internet. I am running Windows 10 and a new Motorola Docsis 3.0 modem. I have reset the airport twice, connectivity restore factory settings twice, only to find out later that the airport has
-
HP Envy M6 1125dx running Windows 8.1 and my fingerprint reader/single pass does not work
Hello I'm not able to use my finger print reader/single pass, now that I've downloaded windows 8.1 Read a few other questions and difficulties people exercise but were not able to always operate. I have a HP Envy M6 1125dx 00179 60246-20486-AA0EM 64-
-
The map shows the region I want, but I won't show as much of the smaller townships how to remove the card and display only the main townships
-
DeskJet 932c, calibration problem - thank you!
Hello! I have recently switched from Win 98SE to Vista Home Premium. My printer is a printer to update HP Deskjet 932c. A driver is already installed on the computer. So the printer works perfectly and very fast. However, the 932 the disc program