Blue Screen of Death (with parameters)

Similar Questions

• We had a power outage in our area, the computer was on and running, got the blue screen of death with the following: __0x000000C2, 0 x 00000043, 0xD6C61000, 0 x 00000000, 0 x 00000000 BAD POOL CALLER

  We had a power outage in our area, the computer was on and running, got the blue screen of death with the following:
  0X000000C2, 0 X 00000043, 0XD6C61000, 0X00000000, 0X00000000 BAD POOL CALLER

  If you have not saved your data and you want to start the computer with Linux Livecd such as Knoppix and copy your data files on an external hard drive. It is a precautionary measure before the step follows because things happens. ;-)

  Then do a repair installation.

  http://www.michaelstevenstech.com/XPrepairinstall.htm

  If the repair installation does not work, test the equipment to ensure that none have been damaged during the blackout and then do a clean install of Windows.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  http://michaelstevenstech.com/cleanxpinstall.html - Clean install - how-to
  http://www.elephantboycomputers.com/page2.html#Reinstalling_Windows - what you will need at hand

  If all goes well, no equipment was damaged during the shutdown. Consider buying a power supply (battery backup). APC and Belkin are good; for a computer, simply spend about $60. MS - MVP - Elephant Boy computers - don't panic!

• Blue Screen Of Death with Windows Vista

  I am running Windows Vista and after trying to update a NVIDIA Geforce driver, my computer will not start at the top and comes up with the "blue screen of death/Disconnections. Initially it started, but icons were very large and I could finally get the right size. Thought that there was a problem with the driver compatibililty and deleted driver (I think), not knowing that I would not be able to find the original driver. Restarted and it is when I got the dreaded "BSOD" and knew with my computer knowledge, I was in trouble. Tried to reboot and then restart with the Windows disk, with the same results. Past to start in safe mode, normal mode, etc... and does not boot in any mode, when eneter is pushed (of your choice) Unit acts as if it starts successfully, with the small bar down Center of screen scrolling as it should, but then the BOSD rises. Support, not much luck, worked with NVIDIA replaced card video, restarted, same result. Need help please.

  Hello

  Here's a problem similar to yours that I help a CO-OP with.

  See if it helps you too.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/unable-to-successfully-boot-syste-after-trying-to/14523396-5c88-4460-A29E-87d03fa00074

  See you soon.

• blue screen of death with cold clone of the linux server

  We have an old Dell Poweredge 2550 running Red Hat 3 Server and we try to use the CD to boot more later/more cold clone to p2v it.

  It stops on the CD, and then after that it shows a loading progress bar get us a blue screen of death (bsod) with the following error

  STOP c000021a {fatal system error}

  The system process Session Manager initialization done in unexpected ways with the State of 0xc000026c.

  The system has been shut down

  It's hard to detect the controller raid PERC or something? We have since tried to use the stand-alone converter from PC software and point it to the Linux box to see if that process works a bit better, which seems to take too long.  I just want to know what happened in the case where the stand-alone converter process decides to vomit on his shoes.

  Thank you all,

  Brian

  Session manager errors are rare with PE - is the CD ok? -, it starts in a virtual machine?

  have you tried other CD of coldclone?

  This redhat machine has dark material?

  as low range or hi-end video cards

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• HP deskjet 1510: blue screen of death with the installation of the printer

  I installed a new HP 1510 about 3 weeks, no problem... then there's 5 days started to have the blue screen of death (BSOD) on & above.   Several hours and attempts to update other drivers, I uninstalled the printer, did a system restore and it worked fine. No BSOD more.

  Waited 2 days, for sure - then reinstalled and the same thing all over again.  So have uninstalled and reinstalled 3 times.

  Ran malware and virus program and nothing came. At the end of my mind - help, please!

  I solved the problem by moving to a port 2.0, restore to an earlier time, and then reinstalling.

• I got the Blue Screen Of Death with Stop: 0 x 00000024 (5898 0x86D4, 0xC0000102, 0 x 00190203, 0 x 00000000)

  Original title: Help, I got the blue screen of death!

  Can someone help me please? Whenever I turn on my computer, it goes to the BSOD. I tried the last settings that worked, but he went to the BSOD too! In addition, safe mode it won't work goes to the BSOD as well. Nothing works. I have to go to a computer store to fix it, or is - it possible to fix it at home? Please help immediately!

  The BSOD I get says:

  A problem has been detected and windows has shut down to prevent damage to your computer.
  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: disable or uninstall all utility defragmentation or anti-virus disk backup,. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /f to check for hard drive corruption, and then restart your computer. Stop: 0 x 00000024 (5898 0x86D4, 0xC0000102, 0 x 00190203, 0 x 00000000)

  Hi TheCookeNinja,

  I suggest you run the check disk (chkdsk) of the Recovery Console & check if you are able to boot to the desktop correctly.

  Step 1: To start the Recovery Console, you can follow this link.

   

  To start the computer and use the Recovery Console

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_overview.mspx?mfr=true

  Step 2: At the Recovery Console prompt, type the following command and then press ENTER:

  CHKDSK [/ p]: [/ r]

  Note: At first, try to run chkdsk/p & check if it helps. Later, you can run chkdsk/r.

  Reference:

   

  How to install and use the Recovery Console in Windows XP

  http://support.Microsoft.com/kb/307654

  I hope this helps.

• Blue screen of death with BCCode: 116

  Hello

  Recently, I started receiving a lot of DBO. I usually get it after watching a video.

  Here are the details that I received on the subject.

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode: 116

  BCP1: FFFFFA800CDFE010

  BCP2: FFFFF8800435B738

  BCP3: 0000000000000000

  BCP4: 0000000000000002

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 768_1

  Could someone give me some suggestions in how to solve the problem?

  Thank you

  Lisa

  Original title: blue screen of death

  for been link... duh!

  https://onedrive.live.com/redir?RESID=1B529A733D6D2EB3! 148 & authkey =! ALPyIEgs1AIRK5Q & ithint = % 2chtm

  Lisa

  Lisa

  No worries I do it all the time.

  These accidents are related to your video driver (yours is 2012) I remove it and install the driver on most recent available (at least 2014 if not most recent)

  

• Blue screen of death with the computer restarts

  Hi, thanks in advance.

  My problem is when I open Skype, whole screen turns blue with an exception system error. Then, the computer restarts and occurs whenever I try to open Skype.

  Please help, I tried to update the drivers and bios, including windows updates, but still the problem persists. I also associate the dxdiag here.

  The BSOD is caused by ASMedia USB3.0 eXtensible Host Controller (asmtxhci.sys).

  Try to downgrade the ASMedia driver:

  http://community.Skype.com/T5/Windows-desktop-client/BSOD-every-time-I-log-in-to-Skype/m-p/4304407#M...

• Vista workaround to access restore partition of the system (0xc0000C1F5 Blue Screen of Death error)

  Stats:

  Computer type: HP-Pavilion a6333w

  Product #: KC746AA #ABA

  Operating system: Windows Vista™ Home Premium (6.0, Build 6000) (6000.vista_ldr.071023 - 1545)

  Processor: AMD Athlon (TM) 64 X 2 processor Dual Core 4800 + (2 CPUs), ~2.5GHz

  Disk space: 500 GB

  RAM: 3 GB

  Graphics card: NVIDIA GeForce 6150SE nForce 430 <-integrated on the mother board.

  ---------------------------

  Location: Try to update Windows Vista SP1 my computer hung up.  After a cold reboot, I got a BSoD (blue screen of death) with the error 0x0000C1F5 code.

  Current problem: whenever I try to boot Vista I get the same error during the vista loading screen.

  I tried the safe mode, the last correct log on the thing, and even a system restore disc that I downloaded from PC World.

  None of these online solutions have worked.

  ---------------------------

  Is there a way to bypass the default loading process and access the recovery partition drive to do a factory reset?

  If there is a way to save the info on my HD it please let me know.

  Thanks, Jcubed.

  Message edited by Jcubed on 11/12/2008 18:06

  I think the (BugCheck Code) code is 0x0000C1F5, and there's a Microsoft Hotfix for this:

  http://support.Microsoft.com/kb/946084

• Satellite L450D - 13 X - black screen of death/Blue Screen of Death

  Hello everyone.

  I have a Toshiba Satellite L450D - 13 X for children, and for the price it's a good laptop. Have had no problems with it until two weeks ago, when the screen froze for boys while playing a game and downloading a program on the net. Had to make a stop of force and since then, we have a BSoD on each startup. That's what we tried:

  On "Starting Windows", we are given the option to either 'Launch Startup Repair' that ends as BSoD or "Start Windows normally" who returns to the list of option "starting Windows."
  Any attempt enter 'Safe Mode' BSOD results.
  Attempt to boot an ISO of the disk recovery Windows on a USB key (we did put highlight and make promotion up) results in BSoD. Borrowing a correct installation of Windows 7 DVD and highlighting what an option cause BSoD.

  In fact, the only option that we used who threw something different has been using advanced startup options. On one of these options, we've got the Blue Screen of Death with the following information:

  Unmountable_Boot_Volume
  Disable memory the Bios Options such as cache/occultation

  Technical info

  Stop: 0x000000ED (0xFFFFFA80023C2CDO 0xFFFFFFFFC0000185 0000000000000000 0 x 0 x 0000000000000000)

  I don't mind erase the hard drive and leave, there's nothing on what is essential. Very, very well, I'd appreciate a steer on it. Checked the Web for things and nothing seems to help for other options. I'm not particularly tech literate but can follow directions.

  Thanks in advance.

  It is really possible that the HARD drive is faulty.
  If possible try to get another same HDD used for test purposes and install OS using the Toshiba recovery image.

  A friend of mine had a similar problem and after Exchange of HARD drive, everything went well again.

• Blue Screen of Death UnMountable_Boot_Volume 0x000000ED

  I get the same message on two desktop computers.  Two of these errors occurred in few days when computers "freeze" while he was working and there was no way out except to turn off and loose.  Neither has been able to load Windows since!

  Both are running Windows xp professional that has been purchased for each computer an update for XP provided on these computers.  I UPGRADE the two original install discs, but I can't use the drive for repairs because the computer boots apparently directly from the HD.

  I still go into this loop.  Windows has encountered an error.  Please restart in: safe mode, last known config or normal etc).  Of course, none of these options do restart except the process of starting the same way.

  I got to the Console of Microsoft recovery with some extra options, but that takes me right to the Blue Screen of Death with details about the error message: Unmountable_boot_volume with the hex codes (the first being 0x000000ED on both computers).

  I found several solutions on the internet, but they all assume that you can go to Safe Mode and run other programs like Chckdisk.  But I just can't.  I got (accidentally I might add) on the screen of the Bios utility.  Maybe it's (HP) computers or age, but on one of the computers, the BIOS page it shows:

  Configuration of the BIOS:

  Master of the first string: Maxtor with numbers.

  First channel slave (none)

  2nd channel Master (HP DVD Writer)

  2nd channel slave (IDE-DVD-Rom 16 x)

  3rd channel Master (None)

  4 channel Master (none).

  In the BIOS utility menu, I tried the F5 to reset the values by default, recorded and released, but everything is still show no change.

  I spend more than 2 hours on the phone with HP trying to get this resolved nothing doesn't.  The technician that I talked to had no idea how to fix this error - even if he said "no problem we will fix that in a minute."  While with this technology, I disconnected everything, rebooted several times by pressing F8 F9, F10 and DELETE, F1.  Finally, he said that the best thing I could do was wipe my hard drive and reinstall the software.

  Of course this is not a solution if the start of corruption can be solved.  And besides, even if I was willing to do that (I'm not still), how the hell I get computers to reinstall the software for two obvious reasons: 1) I have windows XP upgrade disks are installed and 2) the computer cannot read the discs anyway.

  I searched and found a lot of "bugs" on the internet, so it must be a fixable problem.  But most of the solutions assume that you can access your BIOS and change (even if nobody ever says what you should change to?), and then run the patches since the installation of XP discs.  I was also on many other sites that provide a Bootable CD to start Windows XP, but I can not get my computer to see the CD before it starts up.  I tried all suggestions as press F2 when the computer is turned on, and then select boot from CD.  But while on a few occasions, I got the "press any key to boot from CD" (once accidentally so I do not know how to get this message again), it doesn't matter what key has been pressed, it just took me in the loop.

  Does anyone have an answer that starts from the beginning assuming that the computer will not read from the CD and walking then how to understand and fix this problem.  I am sure that there is someone out there who knows how to help with this error message.  At least I hope.  I'm not technical, please keep answers in simple language.  Thanks a lot for your help

  Hi LucyAdams,

  You can follow this link & check if the problem persists.

  When you restart your computer or upgrade to Windows XP, you receive the error message "STOP 0x000000ED UNMOUNTABLE_BOOT_VOLUME".

  
  Reference: Unmountable Boot Volume

  Hope the helps of information.
  Please post back and we do know.

• Blue screen of death: stop error: 0X000000CE

  Hi, I think I got a bad virus on my computer that's all waste.  First of all, it all started when I clicked on a link, while the Christmas on Black Friday shopping. Then I got a download of unwanted software, called system difficulty, (the small icon of Windows) I could not use system restore to remove, whenever I tried to use it, it says cannot restore on this point. Tried several other points, but no joy. Can I get the dreaded blue screen of death with a stop error: 0x0000008e (0xc0000005, 0x804f8e80, 0xef76aa98, 0x00000000). Could sail in safe mode and tried to fix it with antivirus software, found 26, abducted, ran spybot search and destroy, found nothing. Still no joy. So today, I tried to start in safe mode, and it does not work in safe mode, guard reboot again and again. Then I hit F8 and turned restart turned off so I could see the Blue error screen that would flash for just a second, and now I have this stop error message: 0x000000ce (0xf88be6dc, 0 x 00000000, 0 x 00000000, 0xf88be6dc). I read forums on video and all drivers, but this happened just after I clicked on this link and got the virus with this unwanted software download. Anyone got any suggestions on how to solve this problem? Oh and I downloaded a program called error repair of my other computer and installed but it only scan my computer to find errors and then he wants to buy you the pack premium, so that did not help. It's my computer business running windows xp pro service pack 3. Wish it would have been on this cause she has the system recovery and it worked whenever I had a virus, I couldn't get rid of that. Thank you, Steve

  JoseIbarra is the expert resident on the Recovery Console and chkdsk/r. I'll track down his instructions. If the malware is responsible for the BSOD, I do not think that chkdsk /r will help, but it won't hurt. Or you might need to repair your boot.ini file.

  DEFINITELY get this brand XP reinstallation CD Dell! You can use it to perform a clean installation of XP or a repair installation of XP (chances are, you won't ever need to perform a repair installation, but it is nice to have this option) or to enter the Recovery Console to perform functions such as chkdsk/r.
  Chances are that your data does not fit on one CD! Depending on what you have, you might need to up to 100 CDs or more! Better to buy an external hard drive. Newegg.com has a very good selection of the most affordable. Here is an example:
  http://www.Newegg.com/product/product.aspx?item=N82E16822148409
  Creating a Ubuntu CD bootable 'live' (and then startup out of it, rather than on your hard drive) will allow you to copy your data to the external hard drive:
  https://help.Ubuntu.com/community/LiveCD
  There are also some other CD bootable antivirus (like Avira) which may help you:
  http://www.livecdlist.com/purpose/Windows-antivirus
  Here is a link to the instructions of Jose:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/unmountable-boot-volume-stop-0x0000000ed/570c7f90-5869-E011-8dfc-68b599b31bf5

• Blue Screen of Death After adjusting TCP/IPv4-adapter error "STOP: 0x0000007E"

  Original title: Blue Screen of Death After adjusting TCP/IPv4-adapter

  Hi all

  I bought a new USB wireless internet and after installing it, it automatically connects to our network, but fails to connect to the internet. (Local access only)
  A roommate told me that it was something to do with my IPv4 settings. However, after trying to change these settings several times, it always freezes when I push the "close" - button. It is followed by a Blue Screen of Death with the following codes:
  STOP: 0X0000007E (0XC0000005, 0X92C1B7D1, 0X8C1CBC0C, 0X8C1CB908)
  AFD.sys - address 92C1B7D1 base at 92C0F000, DateStamp 4db03801
  I couldn't find anyone with the same problems. Can you help me?
  Thanks in advance,
  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  We prefer at least 2 DMP files to track trends and to confirm the cause.

  
  

  Please follow our instructions to find and download the files, we need to help you fix your computer. They can be found at here

  If you have any questions regarding the procedure, please ask

• You are looking for a solution for Blue Screen of Death

  I am looking for a solution to a Blue Screen of Death with a Message Stop: 0x0000007F (0 x 0000008, 0x803d3130, 0 x 00000000, 0 x 00000000).

  I use a Lenovo T61 with Vista 32 bit...
  Thank you!!!

  It can help to look at the files minidump against accidents with a debugger.

  Can you zip the minidump in the C:\Windows\Minidump folder files and (provide link) available via Windows Live SkyDrive or similar site?

  The following link has information about the use of Windows Live SkyDrive:

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  If you have problems to compress the minidump files copy the minidump files to another location such as a folder on the desktop

  In addition, you do not necessarily have compress the minidump files, you can download one at a time.

• Blue screen of death situation

  Whenever I start some games (Borderlands 2, FEAR3, the two portals and a few others), I get the blue screen of death with these codes BCP

  BCCode: 124

  BCP1: 0000000000000000

  BCP2: FFFFFA800DB8D7B8

  BCP3: 0000000000000000

  BCP4: 0000000000000000

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 256_1
  I'm not very good with computers, but this situation let me no choice to ask people for help
  Does anyone have a suggestion/help?
  Thank you
  Stop 0 x 124 is a hardware error

  If you are overclocking try to reset your settings to standard processor and see if that helps.

  If you keep getting the BSOD here are things more than you may want.
  This is usually hardware related, defective heat, memory or processor even if it is "possible" he is associated (rare) driver.
  
  Stop 0 x 124 - what it means and what to try
  Synopsis:
  A "stop 0 x 124" is fundamentally different from many other types of bluescreens because it arises from a complaint of material.
  Stop 0 x 124 minidumps contain very little concrete information, and it is therefore necessary to address the problem as a case of material in an unknown state of distress.
  

  Generic troubleshooting ' Stop 0 x 124 ":

  1) to ensure that none of the hardware components are overclocked. Material which is pushed beyond its design specifications - by overclocking - may malfunction in unpredictable ways.
  (2) ensure that the machine is sufficiently cooled.
  If there is doubt, open the side of the case (be aware of all the relevant conditions guaranteed!) PC and direct an electric fan squarely to the motherboard. Who will rule on most cooling problems (lack of).
  3) update all drivers related to materials: video, sound, RAID (if applicable), NIC... anything that interacts with a piece of hardware.
  It is best to run the latest drivers anyway.
  (4) update the BIOS of your motherboard according to the manufacturer's instructions and clear CMOS.
  Their website should provide detailed instructions on the brand and model-specific procedure.
  (5) rarely, bugs in the operating system may cause "false positives" 0 x 124 events where the hardware wasn't complaining, but Windows thought otherwise (because of the bug).
  At the time of writing, Windows 7 does not have to suffer from a defect, but it is nevertheless important to keep Windows up-to-date.
  6) trying (stress) test these hardware components that can be put to the test artificially.
  The most obvious examples are the RAM and HDD (s).
  For the RAM, use the 3 rd-party memtest86 utility to run several hours a test value. (6-8 passes to stress the ram)
  For hard drives, verify if CHKDSK /R finds any problems on (s), including "bad sectors".
  Unreliable RAM, in particular, is mortal, as well as software, and anything other than a 100% clear memory test result is cause for concern. Unfortunately, even a 100% clear result the diagnostic utilities does not guarantee that the RAM is free of any defect - only that none have been encountered during the test passes.
  7) as the last of the non-invasive troubleshooting steps, perform a "Vanilla" Windows reinstallation: just the OS itself without additional applications, games, utilities, updates, new drivers - or ANYTHING that does not come from the Windows 7 disc.
  Who stops working mitigate the problem of the 0 x 124, jump to the next step.
  If you run the "Vanilla" installation long enough to convince yourself that not a single 0 x 124 accident occurred, start installing applications and updates slowly, always stopping between successive additions long enough to get an idea of the question if the machine is still free of 0 x 124 breaks down.

  
  Smash back, obviously the latest addition of software may be somehow connected to the root cause.
  If the stop error 0 x 124 persist despite the above steps, and the equipment is under warranty, consider to go back and ask for a replacement that does not suffer periodic MCE events.
  Be aware that want to perform the subsequent hardware troubleshooting steps can, in some cases, void your warranty:
  (8) clean and carefully remove the dust inside the machine.
  Reinstall all memory modules and connectors.
  Use a can of compressed air to clean the RAM DIMM supports as much as possible.
  (9) If all else fails, start removing items of hardware one by one in the hope that the culprit is something non-essential that can be eliminated.
  Obviously, this type of testing is much easier if you have access to equivalent components in order to perform swaps.

  If you are in the situation to have completed all the steps above without a resolution of the symptom, unfortunately the most likely reason is that the error message is literally correct - something is fundamentally wrong with the hardware of the machine.