Boots only to the second power up

Similar Questions

• ThinkPad T410 boots only if the power supply is plugged

  Hello

  I have a really strange bug. My thinkpad T410 (2537-UQF) with an OCZ Vertex 3 SSD boots only if the power supply is connected. If I have a full battery, and try to boot without the power I get a blue screen after about 60 seconds on the screen where the windows logo appears. I have Windows 7 installed fresh a few days ago.

  I think its possible, I've done a few failure with drivers. The power management ThinkPad always stops working after startup. So I deleted the program using the feature "msconfig".

  I'm not really sure what I can do about it. Any idea?

  Thanks for any answers in advance & regards

  Rain

  OK I solved the problem:

  The workaround is to set to battery power settings in the BIOS to auto. If the power in the Bios settings are on maximum battery life, the system does not start if you use the SSD OCZ Vertex 3.

  Hope this helps everyone who has the same problem. I need 4 days to understand this.

  Greetings, rain

• Boots only to the Startup Repair. Hardware diagnostics found bad blocks on the hard disk. is it possible to move data outside of Windows?

  Original title: Hi, I have a Dell Inspiron 1545 laptop.  Recently, he stopped working and would go only to the screen that asks if you want to run the Startup Repair tool.

  Of course whenever I launch it, it goes back to this screen.  Check the diagnostics through the F12 boot, I had three error codes: 0F00:1344, 0244 and 1 A 44.  These were all on the same three blocks.  The message was impossible to read, replace the drive.  I'm really the most responsible for recover my photos, documents, etc. and have an external hard drive.  Is it possible to do so, even if Windows (Vista in this case) will not start?

  Hello

  You can try these methods

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed

  If this does not work, you may need to contact the data recovery specialists

• Combine values separated by '&' only if the second field has a value.

  I try to combine the 2 fields and add & symbol between the two, but only if there is in the second text field.  In this way, I wouldn't end up with "names of seller: Joe Smith &" If there was only one seller name.

  Here is my current script is add automatically of course "and" all the time.

  Get the field values as strings

  var s1 = getField("s1").valueAsString;

  var S2 = getField("s2").valueAsString;

  Combine values, separated by &

  Event.Value = s1 + '&' + s2;

  Replace the last line with:

  Event.Value = s1;

  If (s2! = "" ") event.value +="&"+ s2;

• queryNew type date and time specific only to the second?

  I create a game or an application using queryNew() split a query longer into related parts.  One of the fields in the larger query is a date-time filed with millisecond data that relate to proplerly sort records.  Apparently, the queryNew() function time and date data types are accurate for only the second and is to truncate the necessary data from Ms.

  First question is possible to change this behavior and have the date of queryNew() and | or data types time be more accurate.

  Oh, and I am a muppet. Use 'timestamp' data type.

• Error of the value of the range of the attribute only on the second update of the value each time.

  I tried to create an interface to change attributes of my camera during the acquisition. I created a cluster that has orders for BinningX & Y, cadence, exposure and position. When the VI running everything works fine except when changing the value binning more than once, I always get an error on the second attempt. The range is from 1 to 9 and at the beginning of the VI I can't change any value in this range, but if I try to change it to something else after that, even at 1, I get an error that the value is out of range. Any idea what could be the cause?

  Is attached a screenshot of part of my VI which deals with changing the values.

  Thank you!

  Change the order in which you pass in parameters. I had this problem several times.

  Indeed, if the return on investment that you describe is out of the detection area, you will get this error.

  Do not forget that the X offset + width cannot be greater than the width of the sensor and Y Offset height cannot be greater than the height sensor.

  Hope this helps

• How can they find text only in the second column of the cell?

  Hello world

  I just want to find the second column of the dollar sign
  are intended to be applied to the character style: "bold + italic."

  Can I get there?

  screenshot:

  

  I have this script, can anyone help me change its function?

  If (app.selection.length > 0 & & (app.selection [0].constructor.name == 'Cell' | app.selection [0].constructor.name == 'Table')) {}

  If (app.scriptPreferences.version > = 6) {}

  app.doScript (principal, ScriptLanguage.JAVASCRIPT, [], UndoModes.ENTIRE_SCRIPT, 'style each second column in the selection');

  }

  else {}

  main();

  }

  } else {}

  Alert ("nothing or wrong selection!');

  }

  main() {} function

  var myColor = "PANTONE 252 U";

  var myFillTint = 20;

  var myCharStyleName = "Bold";

  var curSel = app.selection [0];

  var allCells = curSel.cells;

  var startCol = curSel.cells [0].name.split (":") [0] * 1;

  var endCol = curSel.cells [-1].name.split (":") [0] * 1;

  var counter = 1 + startCol;

  for (var i = 0; i < allCells.length; i ++) {}

  var curCell = allCells [i];

  var curCol = curCell.name.split(":") [0] * 1;

  If (curCol, counter)) {}

  curCell.fillColor = myColor;

  curCell.fillTint = 20;

  curCell.texts [0] .appliedCharacterStyle = myCharStyleName;

  Counter = counter + 2;

  }

  If (counter > endCol) {}

  counter = 1 + startCol;

  } / / end if

  } / / end for

  } / / main end

  John

  Hi John,.

  Is that what you need?

  var doc = app.activeDocument,
      _selection = app.selection[0];
  for(var i =1;i<_selection.columns.length;i+=2)
  {
          var _cells = _selection.columns[i].cells;
          for(var j =0;j<_cells.length;j++)
          {
                  var reg = new RegExp("\\$")
                  if(reg.test(_cells[j].contents))
                  {
                          _cells[j].texts[0].appliedCharacterStyle = "bolditalic";
                      }
              }
      }
  

  Kind regards

  Cognet

• Three-Way Color Corrector eyedropper tool works only on the second screen in OSX Maverick

  Hello

  Since the update to the Mavericks at work on Monday, I was unable to use the eyedropper tool to the three way color corrector on a dual monitor configuration in first Pro CC.

  I have all of my panels, outside of my program monitor Panel, on a screen. When I select the Eyedropper to the three way color corrector white balance and go to the second screen where my program Panel is, he turns his back on an arrow and I cannot select anything. When I move my Panel program to display as well as others it allows me to use it as usual. Unfortunately, this is not how I work and I would like that the program works normally.

  I was wondering if anyone else has had this problem and found a solution. I will report to bug right now.

  Thank you.

  Hi Punker,

  Thanks for posting the workaround. It is a known issue that we're investigating. FOW now workaround is to:

  GoTo > System Preferences > Mission Control.

  Uncheck "screens have a separate space.

  System disconnection or re - start.

  The problems must be solved.

  Best,

  Peter Garaway

  Adobe

  Premiere Pro

• Portege M400 boots only when the base

  For the last two months, I have starting problems with my M400. When it is not attached to the docking station it starts as soon as a person out of 30 (or more) times. The rest of the time that it is either the power led flashing orange or simply the Green switch, and do nothing else.

  I tried to start with a/c, A / C + battery, battery alone, but nothing helps. However, when it is attached to the docking station, it starts fine everytime.

  Any thoughts on what could go wrong?

  + The message was edited: link has been removed - unauthorized +.

  Hello

  From my experience the docking station has no influence on the start-up procedure specification.
  That's why I put t understand why the laptop does not start successfully without the stand logged.

  But perhaps it is something wrong with a connection to the motherboard and because of s connected docking station the motherboard would be forced to another post.

  Sorry, mate, but we can only speculate what might affect the start-up procedure specifications

• Qosmio X 500 stop during the game - but only on the external power supply!

  Hello.

  Since I updated my BIOS to 2.9 I had this HUGE problem. And now, I created a user here, in the hope of my colleagues advice owners of Toshiba.

  Let me cut it, as it's enough for me confused.

  I bought the computer in March 2010 - is still under warranty.
  I updated the BIOS from 2.8 to 2.9. I always kept my computer up to date with the latest drivers Toshiba - and is still.
  But now, after update BIOS, all of a sudden, my computer shuts down, rotates instantly, as if someone pulled the cord and there is no battery attached.
  But it happens that whenever I start a GPU really requiring program/application. It is not happed when I use the computer for all the days of the things or watch movies etc.

  I put it well 3DVantage and of course, it crashed.

  BUT!

  If I pull the rope and let it run on battery - even if the performance that comes out is less - it does not crash, never, in any game that would break if I had the string attached.

  I was in touch with Toshiba service in Scandinavia - I live here and they couldn't tell me what was the problem, but they were pretty sure that it was not related to the BIOS, because while I was talking to them, I installed 2.8, and it's the same thing.

  It has been sprayed, treated and some more with compressed air, and if there is no dust left, it would be like concrete. I ran the game in windowed mode, while having Speedfan running, the temperature will never be greater than 65 degrees Celsius. So it isn't heat related.
  I used 3DVantage to test the CPU and see if that too would break, once again nothing.

  I think the long terms of workload. The GPU goes off when the workload exceeds a certain percentage/voltage/whatever and something in the BIOS which controls it, changed or left unchanged and there for is not skilled with the rest of the updates to the BIOS.
  Or maybe the problem is not BIOS related? is it something else? I'm really confused and the fact that I can use it for simple tasks, only confuses me even more - so this is only a part of the graphics card which is damaged?

  Even if it is under warranty, wait 10 days (if I'm really, really lucky, like place I bought it, is not exactly known for good service condition) is the last option.

  This explanation is rather long, but I'm not not short versions, and if you feel like I left something, say so, and I'll do my best to provide you with information.

  Thanks in advance!
  Nikolaj.

  Post edited by: n_larsen - typos.

  > Speedfan shows also a tab called Temp1 - ACPI... It may be offtopic, but what is?
  When I order the windows event log, it shows some errors about ACPI: (translated by myself from Danish)

  Advanced Configuration and Power Interface (ACPI) specification is an open standard and defines independent interfaces for hardware discovery, configuration, power management and monitoring.

  66 temperature is not too high so I n t think that automatic shutdown of the bottom are related to temperature.

  I have your case, I recommend reinstalling the OS window once more; install the operating system preinstalled Toshiba using the recovery disk.
  Then check the features of the laptop. I mean that you should not install any other software before checking the laptop. In many cases 3rd party software could lead to problems of different laptop then you should check the laptop using factory settings.

• Qosmio G20: How to run programs and movies only on the second screen

  It is possible to select what programs are displayed on the secondary display (tv)? If so, how.

  If I have a movie on TV he also plays on his laptop computer and all. How can this be stopped IE only play on tv?

  Norskman

  Hello

  Usually, you can change the display with the function FN + F5 devices.
  Then, you can change the option for laptop / LCD, LCD, laptop computer screen / TV, TV

  If you use the software as WinDVD, so you first change the display device and then use the software.

• Equium M50-164: mouse jumping when only on the main power

  Hi guys

  I have an equium M50-164...
  around the age of 19 months

  The touch pad slow corners and departures from flickering pointer and jump when the mainstream and it works normally when it's on battery...
  Can you help me with this?

  I tried to remove the battery, once again, fixing of reinstalling the driver etc...

  Pls someone help me with this?

  Hi guy,

  I'm afraid that this problem was caused by a malfunction of hardware and reinstalling all the drivers or software won't help m.
  If all goes well there s nothing serious to a case value it might be something wrong with the motherboard and the repair would be costly.

  But don t worry ;) in my opinion there of only one keyboard or touchpad fault.
  So the replacement should not be very expensive
  Before you continue with the new measures such as purchase, replacement parts, I would recommend contacting the service provider allowed for the provisional diagnosis.

  Good luck

• &lt; iframe &gt; link to #anchor work only the second time

  I explore a way to offer a local within a framework of content Web HTML file so that it starts at a specific HTML anchor point rather than the top of the HTML page.

  Now, given that the Web Content overlay of DPS does not support URL + format (e.g. myfile.html #myanchor) of the anchor chain, I thought that I could achieve the desired result by loading an HTML file in the superposition of Web content that points to the HTML file and its anchor named in a tag < iframe >.

  It is where it gets boring. The solution works... but only on the second time you call to the top of the Web content overlay (normally hidden in an MSO).

  The first time I have call the overlay Web Content in my article DPS on the iPad, however, the HTML page but not the specified anchor point, or indeed at the top of the page HTML - instead, it seems to start a little more down the anchor. If I reject the superimposition of Web content (in my case, switch to another State of the object) and return, the HTML code recharge starting at the position of the anchor, exactly as planned. I can close the folio, reopen it and the behavior is always correct. It was only the first time that it fails to do the right thing.

  I am very happy that my solution works on the second, third and every opportunity, but it's very important that readers see first working time.

  I tried to delay automatic playback of the content of the Web, but this makes no difference. The anchor is identified using the tag "id".

  Any ideas?

  Thank you, Neil. But you can ask your guys to withdraw. Someone made me a coffee strong tonight and I realized that I was this approach from the wrong angle. I've seen this number of HTML pages requiring a refresh before you display it correctly in other circumstances, even in Chrome on my computer, so I doubt that it is a specific problem of the DPS - maybe it's something in webkit.

  Anyway, the coffee made me realize that I have an iframe to load another HTML file to an anchor. All I need is to pop a little GoToAnchor script in thetag and a call at the beginning of thetag.

  Someday, if someone corrects completely broken site of Adobe Cookbooks, I download a lot of these recipes.

• I'm not able to install both on the same PC LabVIEW applications. I have uninstall the first application in order to install the second. Is there a way to avoid this?

  I wrote two LabVIEW applications. The first acquires data from three different devices, displays the data and writes it to a file. The second application reads the data and displays it on the screen.

  Can I install the first application and run it, but I can only install the second application if I uninstall the first application.

  Any ideas as to why this is happening?

  You install applications by using a Setup program created with the application builder to LV?

  What LV version do you use?

  You have a dedicated for each installer build script, or do you still want to change the settings of a single build script (which would be a reason for this behavior!)?

  hope this helps,

  Norbert

• SSD for boot only on 1170 HPE-9.

  I just bought a 1170 HPE-9, and it came with a SSD 256 GB and a 1 to as the secondary drive. Is it possible to configure the computer to just use the SSD for boot only, and have all new program of these games, videos and large files to use the 1 TB.  Somewhere, I continue to move these files to the 1 TB drive, but some of the reasons that some programs can do, but others install automatically on the SSD (C:\), fills the SSD so fast.

  Are there any suggestions or comments to avoid such as Itunes or any portal application of games to download directly on the 1 TB.  I know that before the application is downloaded it normally asks you where to install, but in many cases, is not.  I just want to put the SSD just to boot only and the necessary windows files.  Is there a setting in Windows 7 I need to change or RAID configuration or any?

  Yet once, I enjoy comments and/or suggestions.

  Hello

  You can use Windows 7 to move several folders listed under your user ID.

  C hard drive :--> users--> 'your name'---> you can then right mouse click on folders such as: my videos, my music, My Documents, my pictures, Favorites, then choose location. Then use Move to move the file and remap the location on the desired location (1 TB HDD). See the example below.