Bridged network

Similar Questions

• Ethernet link to the bridge network and server

  I'm not an expert and hope that I do not use the wrong terminology, but I have an intermittent fault which has become more or less permanent. My major son put up for me a computer with Windows 8 as its operating system and a server for storage, connected by a cable to transfer files. The computer has its own router, with which it communicates with the local network based on a router and modem in the next room. There is a network bridge to access the internet. Initially (January 2013) it worked well. Sometimes, I couldn't connect to the server immediately, but simply another attempt was enough to access it, and he had no problem with the internet connection.

  More recently (late July and August 2013), it became more difficult to access the server and now seems permanently impossible, the server simply showing with a red X across as one of the devices on the computer page. The Internet becomes also more difficult, although there is no need for the server or available to arrive and still connects for a short while before disconnect. In July, the internet can usually be restored by turning off the modem and the router, and when they were on again to restart Windows 8, but that no longer works. I tried to reset the computer to the previous settings, but without success. I also tried the diagnostics tools, but generally, they fail to address the issues identified, except for an occasional brief of the internet. Until today, it has always been possible to show the LAN on the network page, including the iMac computer and printer next to the router and the modem, but today the network folder showed most of the time as empty, any diagnosis I ran in the attempt to identify and connect to the local network, which today needs to manually connect even if automatic connection is checked. Conversely the iMac can still see the computer Windows 8 when he is awake through the LAN, but only in January, he sees the server.

  The error or the troubleshooting messages that have been published are (1) to the server: the (network) path could not be found, or the name is already used. The IP given my son is 192.168.0.101, I tried and failed to find in the browser of my iMac, which does not suggest that it is already in use. Even if it wasn't a valid IP address, it would not have worked between January and July.
  (2) for internet access: reset of the card of network bridge that can force a reboot with a reference to the AREA of PAGE_FAULT_IN_NONPAGED_ that I can't continue without an internet connection. unresolved issues can include one or all of the connection between your modem cable, router or point of access and the Internet is broken. "Network bridge" is not a valid IP configuration. the default gateway is not available. The computer in the other room has had uninterrupted access to the internet, so it is unlikely that the router or the modem it are at fault, who leaves the access point or the configuration of the network gateway. I found some of these error messages in the discussions on Windows 7, but not for Windows 8.

  Finally, the watch status bar above all a network with limited access and a connected LAN ethernet bridge, which is not enough to bring me to the server or the internet; However, today the necessary local network setting procedure of discovery of devices running and by ticking the automatic connection to the LAN router in the next room, although both had previously been functioning. Is this the consequence of Windows updates downloaded and installed since January? Very briefly this afternoon after having restorng the settings they had on August 5, the convenience store was able to solve the problem of the bridge network, only for access to the internet to be cut shortly afterwards for lack of a valid IP, a problem solved configuration a few minutes before. Would it be possible to obtain internet access directly via the LAN network without the need for a network bridge, or is it a mistaken assumption on my part? Even if this is right, remains the problem of access to the server. Any thoughts anyone?

  Hi Clive,.

  If you have included a lot of details about this question in the thread, I was unable to get a clear picture of the network configuration you have. What is the topology of the network that you set up?               How the server is connected to the network? What is a Client-Server network model you have?

  If Yes, then this problem is better suited for it professionals about TechNet Forums that are well equipped with the knowledge of Client-Server network issue. Please post your question in the TechNet Windows 8 IT Pro Networking Forums from this link:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w8itpronetworking

  Hope this information is useful.

• cannot change the network not jumpered it is no host not bridged network adapters

  Hey guys, wondering that if you can help me with this, I've upgraded to windows 10 and have this annoying issue in vmware workstation 11

  I want to VMnet2 only use my MIFI wifi and not my regular internet so I went to the virtual network editor like I did before and added vmnet2 but when I check the box for height to select the wifi it says "can't change network to not bridged there is no host not bridged network adapters" which has left me speechless >. <

  Just a guess. Check vmnet0 (default bridged network) to see if it uses a dedicated, network adapter or is it still set to automatic.

  André

• VMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10 - known issue?

  Hello

  I upgraded the PC host, but also virtual machines to Windows Pro 10.

  TheVMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10...

  Is this a known issue?

  Thank you!

  Kind regards

  Joe

  SOLVED!

  
  

  I uninstalled VMware Player, including the abolition of the configuration files.

  
  

  re-installed VMware Player and it worked!

• Bridged Networking problem - comments may be crazy, but nothing else can connect

  I have a few bridged networks confusion works correctly under VMWare Workstation 11. Installation is VMWW running on a Windows Server R2 2012 host with a Ubuntu LTS 14.04 server prompt.

  Windows Server has a physical NETWORK adapter that is configured with two IP addresses.  For the sake of argument, that I will call the first IP 1.1.1.1 (255.255.255.192 subnet mask) and the IP secondary 2.2.2.1 (netmask 255.255.255.224).  Real IP addresses are all publicly routable.

  In my computer, the network configuration is set to "bridged".  Inside of the Ubuntu VM, networking is defined as follows:

  2.2.2.2 IP address

  255.255.255.224 subnet

  Gateway 2.2.2.1

  I can ping successfully the Ubuntu prompt from the Windows Server and other computers on the Internet, but cannot connect to any other service on the client (for example, SSH, HTTP, etc.), either from the host machine or any computer on the Internet. Note that both hosts and guests have their respective firewall disable for the moment.

  However, if I change the VM network config in my computer to be "NAT" and set the networking of Ubuntu on DHCP, all services on the client are accessible on the host Windows (for example, SSH, HTTP etc.) via a 192.168.x.x dealt with this workstation DHCP assigns the guest.

  I'm a bit puzzled as to why these services would be accessible to the NAT address, but not on the static IP address public when the latter may be ping from the host and other machines?  Any suggestions would be greatly appreciated.

  OK, managed to solve it with a violin.  The resolution was to create a new virtual network adapter in the virtual network Editor.  It has been bridged, with the physical NETWORK adapter selected in the drop-down list 'Bridge '.  In this case, this has created VMnet2.  Then in the VMWare Workstation GUI, I edited the network adapter settings to select VMNet2 in Network Configuration options.

  No idea why it did not work with VMNet0 at first, but still...

• Bridged Networking crushed Vmware Fusion 6.0.4 - replicable

  I use the version of 30 trial of VMWare Fusion 6.0.4.  I can't sign up and download a .zip file officially, because I have to register the product first, and it won't let me register the serial number of the trial.  I won't pay until I am sure that it works for my use case.  So I have to resort to these forums.  Here's my reproducible bug:

  I'm running a Windows 7 VM.  I used the import function to import this machine virtual of Parallels Desktop version 9.  It starts and works fine as long as I'm using NAT networking (shared with the host).  As soon as I switch to Bridged networking, it starts and runs for about 15 to 30 seconds, then crashes.

  I used "Information Support" to create a zip of debugging information file and he have attached to this post.  Help!  I need to use Bridged networking.

  Hi petec35_2!

  It seems that your guest uses frames (or Jumbo Packet), and which is currently to trigger this problem in Fusion.

  To work around the problem: in the guest Device Manager, find the E1000/E1000e NIC, then a parameter in its property page should allow you to disable the Jumbo Frames/Jumbo Packet.

  See you soon,.

  --

  Darius

• No VMnet0 or bridged network

  I installed VMware Workstation on a system Windows 8 10.0.1.  When I open the virtual network Editor, there is no VMnet0, and I can't create a network with the bridge enabled.  I get the following error:

  Cannot change the full network: there is no host not bridged network adapters.

  Networking works very well on the host system.  I found nothing useful in the documentation that guess vmnet0 is and functional very well as a bridged network and Googling has not given anything useful yet.

  Thank you

  Curt

  I'll check the observer of events and if appropriate try to re - install with McAffee turned offshore.

  As soon as I saw "McAffee" (it's actually, McAfee) I Wen ugh!  IMO McAfee is one of the worst products personal computer firewall and AntiVirus is there and I never use it on personal computers.   You need to maybe actually completely uninstall McAfee and then install VMware Workstation.  Then test it before installing your 3rd part AntiVirus/Firewall, McAfee I hope not!

• Ubuntu 9.1 bridged network

  I can't get the bridged network setting to work with 64 bit Ubuntu 9.10 Server. I can't ping my host OS machine, it works if I select NAT.

  I need filled since I want someone outside my network to see the machine.

  I use 7.0.0 - 203739 OF WMware workstation and Windows 7 Ultimate 64-bit as host operating system.

  I've attached a screen shot of the Ubuntu network.

  Here are my settings in Windows 7:

  > ipconfig/all

  Windows IP configuration

  Name of the host...: i7

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  Adapter Ethernet Local Area Connection 3:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: TAP-Win32 adjust V9

  Physical address.... : 00-FF-C6-59-00-F9

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Ethernet adapter vpn1 - Client VPN:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Description...: Map of customer VPN - vpn1

  Physical address.... : 00-AC-03-BF-3A-93

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Ethernet connection to the network space 2 card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ethernet Controller #2

  Physical address.... : 00-26-18-08-5C-EC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :

  ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ethernet Controller

  Physical address.... : 00-26-18-08-5C-ED

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::11b8:b411:5356:9976 %2 (Preferred)

  IPv4 address: 192.168.0.4 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Thursday, January 14, 2010 03:17:35

  End of the lease...: Friday, January 15, 2010 18:20:22

  ... Default gateway. : 192.168.0.1.

  DHCP server...: 192.168.0.1.

  DHCPv6 IOOKING...: 201336344

  DHCPv6 DUID customer...: 00-01-00-01-11-D8-BE-E8-00-26-18-08-5C-ED

  DNS servers...: 192.168.0.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet1:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet1

  Physical address.... : 00-50-56-C0-00-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::f8cb:178e:62bb:249e % 18 (Preferred)

  IPv4 address...: 192.168.137.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 419450966

  DHCPv6 DUID customer...: 00-01-00-01-11-D8-BE-E8-00-26-18-08-5C-ED

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet8:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet8

  Physical address.... : 00-50-56-C0-00-08

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::f8ea:b0f6:c517:53ba % 19 (Preferred)

  IPv4 address: 192.168.254.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 436228182

  DHCPv6 DUID customer...: 00-01-00-01-11-D8-BE-E8-00-26-18-08-5C-ED

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Network adapter Ethernet VirtualBox:

  The connection-specific DNS suffix. :

  ... Description: VirtualBox Host-Only Ethernet adapt

  Physical address.... : 08-00-27-00-A8-BF

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::75b9:51cb:4b9b:8065% 22 (Preferred)

  IPv4 address: 192.168.56.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 369623079

  DHCPv6 DUID customer...: 00-01-00-01-11-D8-BE-E8-00-26-18-08-5C-ED

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {FD680579-FB4A-467F-BAF3-A7948837612B}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft ISATAP adapter

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {C18DAE31-2110-427B-BE2E-50B57663241A}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #2

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {9690C2AD-89C4-4188-AE02-20FFC1FA76E3}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #3

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {C65900F9-17D6-4AB4-A96C-CB34EA7F389A}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {7DA81159-B719-4577-B33E-F92F1A7A4407}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #5

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {AF582351-B45C-4E4B-8F57-65F4B3C3040F}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #6

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {DE07A035-B63D-403C-8402-4A1FEB25501C}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #7

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Lasse

  "you have more than one physical network adapter - this means that you MUST disable"automatic gateways"in the virtual network Editor"-Please check that first.

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• Bridged networking: host and invited him IPs?

  Topology: physical router (IP 192.168.1.25/24) connects to the host (IP 192.168.1.1/24) run a virtual machine (IP 192.168.1.2/24).

  Question: using cargo network, the virtual machine cannot connect through physical NIC in the host to the router - all are on the same subnet.

  I use network bridge to connect to a virtual server to a physical network, but I'm confused about which IP addresses in use on the map the host's physical NETWORK and virtual NIC the guest to my knowledge, as well the host physical NIC and virtual NETWORK card of the guest OS must be on the same subnet. If I assign 192.168.1.1/24 to the physical NETWORK adapter on the machine host and 192.168.1.2/24 to the virtual NETWORK adapter inside my guest operating system virtual (using network properties), the guest operating system must therefore able to communicate with the outside real network. But it may not. However, I have noticed that if I use "Obtain an IP address automatically" for my NIC host, it is assigned an automatic address 169.254.1.1 (an APIPA address). My virtual network adapter has been assigned the address 192.168.1.2/24 inside my guest operating system. And it can communicate with a router that the host computer is connected to an address of interface of 192.168.1.25/24. That makes no sense.

  My understanding is that when using bridged networking, the guest operating system has a virtual NETWORK adapter that connects to a virtual switch (VMnet0). The host operating system has a real physical NETWORK adapter that connects to the virtual switch (VMnet0). Then, it follows that the host's physical NETWORK and virtual guest NIC card must be assigned in the same subnet IP addresses to communicate? However, as stated, with these settings the guest operating system cannot communicate through physical NETWORK card from the host to the outside world. But when I assign physical NETWORK adapter of the host, an automatic address (when ends up being 169.254.1.1 when checked with ipconfig), work of communication. Can someone explain this?  Thank you very much!

  MikeF007 wrote:

  Only bridged connections are used without NAT.

  I asked you to try this... you do not have.

  Eagle server running a DHCP server, but the host PC needs to get an IP address before it connects.

  You can't run a DHCP server as a guest (fedora) and serve as the host. You must use a fixed IP address, which is reserved for the host and the host running the dhcp server.

  No VLAN is used (except 1 VLAN by default of course). There is no security or MAC filtering on the server of the Eagle.

  VLAN is not supported in Server 2, with the exception of the static (based port).

• DHCP bridged network problem

  Hello

  I would appreciate if you could help me with this one. I've invited windows server 2003 running as a service in a host of xp. Don't ask why a service! I just need it!

  I use bridged networks. The guest does not seem to get an ip address from the router dhcp off the map wireless of my host. There is something strange. At home, I have a netgear router and have no problem getting an ip address, the problem is at work where there is a linksys router. On the host, I have no problem with the linksys router.

  Thank you very much in advance.

  PS: by the way, I'm using vmware workstation 6.0.2

  despuestambien wrote:

  Hello

  I would appreciate if you could help me with this one. I've invited windows server 2003 running as a service in a host of xp. Don't ask why a service! I just need it!

  In fact... I think I'll ask - why?  If you run a guest as a service, you should look at using the free VMware Server product instead of VMware Workstation.   VMware Server is designed to run guests in the background.

  I use bridged networks. The guest does not seem to get an ip address from the router dhcp off the map wireless of my host. There is something strange. At home, I have a netgear router and have no problem getting an ip address, the problem is at work where there is a linksys router. On the host, I have no problem with the linksys router.

  At work, do you think they put in WiFi AP MAC address restrictions?

  PS: by the way, I'm using vmware workstation 6.0.2

  Consider the upgrade to Workstation 6.5.2. This is a free update for you.

• Bridged networking issues Vista 64-bit

  I have problems with the help of Bridged Networking in VMWare Workstation 6.5.1 with my host OS under Vista 64 bit Ultimate SP1 and guest of XP sp2/sp3 os and / Vista 32-bit.

  NAT works fine but actually not.

  Things I've tried:

  Setting bridged adapter manually

  Deactivation of VM virtual cards

  Definition of default gateway in home

  Vista firewall disabled

  No matter what I do, I can't get a connection to the network via a physical bridge connection in the guest operating system.

  Thoughts, suggestions, etc. would be greatly appreciated, just NAT does not work for me I need to my VM appear to be on the same network as my host OS and other computers.

  Thank you

  Patrick Stuart

  I would like to delete the default gateway hardcoded on your comments so that it does not cause problems if you fall in network work bridge.

  What antivirus do you use on your host and guest?

  There is a host of Vista - but I don't see the typical IPV6 entires in the output of the command ipconfig/all.  I just want to confirm that there is a reason for that (you manually disabled IPV6 or something)?

  What is the 'virtual SafeNet QuickSec card' for your host?  What is a VPN product?  Features of firewall?  I'm here, but if you have the time, maybe try to uninstall this product to see if it makes a difference.  Here is another post about SafeNet for a different problem, but maybe try the suggestion it will help: http://communities.vmware.com/thread/11884

• Bridge network merger has stopped working

  I did turn XP Pro 32-bit + Leopard successfully for about a year now. Suddenly today I started to get this message while booting XP using Fusion...

  The network bridge on/dev/vmnet0 unit does not work

  If I switch to NAT I can connect to internet just fine, but not via the network bridge.

  Sorry its such a "retarded", but that someone has any ideas what may be the problem, or why it should suddenly have manifested itself. Also, what are the consequences, if any, running in NAT instead of using the bridge network connection.

  Thanks in advance for any help that may be available

  Please check the IP address and restart the Virtual Machine and Mac system and check.

  Kind regards

  Silica V.

• The bridge network to the ethernet ports

  I have an Airport Extreme base station for my wireless at home. The problem I have is that the base station is not near a few features, that I need to hard wire. I read that you can set up a network bridge and if I understand correctly, this concept, it's like setting up of another wireless device, but this second device provides you with the required Ethernet ports for connectivity. Is it possible to do with the Airport Express secondary device?

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network however. Is this feasible? All known reserves? Advice is appreciated.

  Is it possible to do with the Airport Express secondary device?

  Yes

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network but

  It all depends on if you configure the AirPort Express to "extend" the network... which will lower the maximum speed potential of the network by all 40-50%...or...whether that you set up the base AirPort Express for simply to 'join' the network... which causes a decrease in the speed of the network... but it will provide 2-port Ethernet for wired devices.

  If you need more than 2 ports Ethernet on the Express, you can add an Ethernet 5 port, 8-port switch, etc., to create as many ports as you need.

  Don't know what kind of speed you need for the Ethernet ports, but they are limited to 100 Mbps, then that would be the maximum speed available ports Ethernet on the Express.

• Made a bridge network distort your IP address for file sharing via a WIFI network?

  Dear Microsoft Answers,

  I have a network bridge set up the connection of two network cards wireless (an external and one internal), one of the witches providing internet service via the WIFI of my neighbours, the other to distribute the signal through MY House, some between my iPhone and my PC wireless file sharing works all by sharing connections but not when jumpered. I need bridge for good internet services connections. Please , can someone help me with this, Ive been having SO many network problems lately, and I hope for relief. Thank you!

  Hi Rio12345,

  We recommend you to check if the Windows Firewall or any other firewall installed on your computer allows the devices to communicate on the bridge.
  See Allow a program to communicate through Windows Firewall

  For further assistance, you can get in touch with iPhone support team

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Ubuntu LTS 14.04 VMW 11 - network only works correctly if used DHCP on bridged network mode

  Hi people,

  I am pretty new to Linux things, so I installed an Ubuntu LTS 14.04 as a LAMP on VMW 11 server.

  The networksettings VM are bridged, so I should be able to access the virtual machine as a normal member of my network:

  

  Here are the settings when I activated the DHCP and as you can see, the server has no problem to connect to internet. The name is resolved properly and all is well.

  

  Everything here is the opposite, static ip and no connection. But with the exception of la.130 who changed a.201 everything is identical, but nothing works. Even the host no longer be resolved...

  

  I hope you can help me with my problems, I have no idea what's wrong with my settings.

  Thank you!

  I don't always have an idea what has caused all this does not work with cette.201.

  I've set up another address and now everything works fine.