Broadcom Teaming 5709C emits in Win2008 R2

Similar Questions

• How to install additional network drivers?

  Hello

  Newbie question...

  I recently installed VMServer 2.0 on an IBM server, which has a Broadcom BCM 5709C NetXtreme GigE network adapater (2 x).

  After I installed Windows 2003 SP2, the VM host environment, detects only AMD PCNET card.

  This adapter is able to connect to the host.

  Please let me know how do I install additional network drivers.

  Thank you

  Chris

  Hi Chris,

  Welcome to the forums.

  VMware solutions never present physical network cards to the guests, but only the emulated cards. The operating system detects the virtual card, and most of the time, is able to install it with the driver of a standard distribution. Your Windows Server has detected and installed the device AMD, which should be OK. So do not try to install another, especially the Broadcom.

  You specify which network the guest will be connected by using the configuration of the VM from VMware. Then you decide if you attach the guest to the public network or to a private. If your virtual machine connects to the host, take a look at the network configuration of your VMware Server.

  It will be useful.

  Concerning

  Franck

• Pavilion 15-p262nf: network card driver Broadcom emits

  Hello guys! I need assistance with a recently purchased HP Pavilion running on windows 10 15. While trying to update my Broadcom Wi - Fi card via the HP support assistant, the installation has failed and left me no Wi - Fi. Could you point me to the correct driver, I need (hardware ID: PCI\VEN_14E4 & DEV_4365 & SUBSYS_2230103C & REV_01) as well as help on how to install it properly, as the automatic and manual installation have the unfortunate habit of neglect and delay...
  Thank you very much!

  Unfortunately, I don't have any other suggestions for you to try.

  At this point, you can back up files that you do not lose and perform a system recovery.

  You have the key wireless under correct voltage?

• HP proliant ml310e gen8: can't the Nic Server 2012 team

  Hello everyone hope everyone is great

  I have a hp proliant gen8 ml310e I have a problem, do the 2 Nic set interfaces

  I tried 3drivers the

  1 Microsoft driver by default with windows server 2012

  2 broadcom driver the latest driver directly from the Broadcom website

  3 hp driver from the drivers from the Hp site for this model

  When I go and try to create a Nic team a mistake occurres and Nic fails creative team I also tried doing it through power shell operation has expired: TeamNic installation has not completed on time.

  I tried a clean format

  System specs

  HP proliant ml310e gen8

  Broadcom NetXtreme Gigabit

  Server Windows 2012

  Hello:

  You can also ask your question on the Forum of Support Community Business Enterprise HP - ML servers section.

  http://community.HPE.com/T5/ProLiant-servers-ml-DL-SL/BD-p/ITRC-264#.Vp1hReT2bGg

• NIC Teaming Poweredge R420

  Hello:

  I am collecting information to configure NIC teaming on my server Dell poweredge r420.

  Other posts I've read it is mandatory, installing broadcom software and update the firmware of the NIC (Broadcom Netxtreme gigabit ethernet).

  I can't find the broadcom advanced control suite window to set up the consolidation of network cards.

  Can someone help me?

  You can access the Web from Broadcom site and download it here: http://www.broadcom.com/support/ethernet-nic-netxtreme-i-server or there are updates on the Dell Web site: http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=2T17H&osCode=WS8R2&fileId=2961022443#

  Hope one of these works for you.

  Wheeler Mitzi (Mitch)

• Dell N2024 - NIC Teaming (LAG, LACP)

  Can you point me to some documents or provide the steps how to create team on Dell N2000 Series switch ports.

  I set up a team of the NIC on a server r2 Windows Server 2012.  I need to know what needs to be configured on the N2000 Dell series switch to make sure it's working properly.  It is my understanding that you need to configure the server and on the ports of the switch stack.  In my case, I'm going to a team member of the server connected to port 1 of the switch 1 and the other plugged into port 1 of the switch 2.  Any help is greatly appreciated.

  Thank you

  Hello

  It depends on what mode of grouping you use on the server. If you use the Windows team work construction you can choose between independent, does not require any static configuration or on the switch and LACP what to do. Broadcom and Intel Group also have similar options. To configure a switch port channel, you select the ports you want and use the channel-group command to add them to a port channel.

  Page 593 ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_fxd_prt_swtchs/networking-n2000-series_Deployment%20Guide3_en-us.pdf

• Aggregation of links between poerconnect 5324 and poweredge with broadcom adapter

  I am looking for information on how to build an aggregation of links between my powerconnect and three cards broadcom on my server. I want to create a bandwidth of 3 GB.

  I created a team with suite ABEC 3.

  My network have 2 VLANS.

  At this stage, I could ping my server network, and I can ping the server in my network.

  When I defined the three ports of the switch (where three cards are connect) as LASG and I defined in belonging to a VLAN these three ports whose status is F, I ping the server from the network, but I can't ping the server network.

  Could someone tell me how I could build this bandwidth betwween my powerconnect, and poweredge?

  Thanks a lot for your help.

  
  

• C200 M2 Windows 2008 R2 NIC Teaming question

  I have a c200 M2 Server with a map of map NETWORK Broadcom addon (N2XX-ABPCI01).  I would like to create a NIC team with all 4 cards (2 on board and 2 Broadcom).

  I found the enictool on the CD, but when I run it, it is not announce adapters or teams.

  How can I create a team on this server?

  Thank you

  Dave Harrold

  Hi Dave,.

  Utlities CD/.iso, you can find the BINS utlity for broadcom. This should help you.

  . / Afonso

• XPS 8300 nine connects to the Broadcom Netlink Communication card only after restarting 3 - 4 times at cold start.

  Hello

  I just bought a new XPS 8300.

  After woeking OK a few days, now it connects to the Broadcom Netlink Communication card only after restarting 3 - 4 times at cold start.

  Someone has the same problem?

  All other computers in the House connect from the first shot. (two cell phones and another office.) They have much slower computers.

  In the beginning, I have re-installed the driver (DVD and downloaded), but not that's the problem.

  The computer must have a little hot.

  When it does connect, Test the Dell tool DOES NOT SHOW (does not appear in the list of tests) Broadcom NetLink Gigabite Ethernet card.

  I'm a little disappointed, it's a brand new computer, I was expecting more problems from the beginning.

  Thanks, Cristian, Montreal, Canada

  All,

  According to the received update, please call Support technical and would take appropriate action.

  The fix is based on case to case, so I would ask all those who face this problem to call tech support for your region.

  The technical team sent details to the technical team and the TS process for this issue should go smoothly.

  FYI: I was not provided with a patch, please contact Dell Technical Support for more details.

• Failure of issue and pilot Intel TEAM

  I was going through updates on my servers via the Dell OpenManage Essentials and decided to go ahead with the update of the requested network driver:

  Network_Driver_HP103_WN64_16.5.0_A00

  During the installation, I got and error reading 'failed to install.  Missing or corrupt file: HELP. CABIN.  I clicked on OK and the installation read as "successful" but wiped my TEAM and connections.  I don't have a Broadcom cards so cannot the team using them.  I have Intel Gigabit and 10 4 P X 540/I350 NICs installed without grouping option.  I went to a configured a NIC unique static run for now, but I need to get the TEAM to work again.

  Any suggestions?

  BillandMisty78,

  After researching the issue, I suggest you do the following.

  1. Rename or delete the following folders:
     "C:\Program Intel.
     "C:\Program Files (x 86) \Intel.

  2. Export and delete the following registry key:
     HKLM\Software\Intel

  3. Right-click on the installation of Intel and run as Adminpackage.

  After the update, it should work fine. Let me know how it goes.

• ESXi 5.5 nic teaming/LAG with trunking does not but it works on ESX 4.0.  Both are on the same switch. What gives?

  I have two hosts (vhost1 = ESX 4.0, vhost2 = 5.5 ESX) both are configured for the Group and both connected to a switch of 1544 Adtran L3 (named sw01).  vhost1 has been in production for several years with the config below and has been solid as a rock.  I'm trying to reproduce the installation of grouping/collage on vhost2 and it does not work when are associated but will work when you are using a single NIC (with or without aggregation).

  To be more specific about what does not work, two virtual servers have "Network server" (vlan 8) defined as a group of ports. Both physical and virtual servers on the same vlan cannot ping or resolve queries arp for virtual machines on vhost2.    Everything that is sent from a different subnet can connect to the virtual machines on each virtual server.

  So the question is this: why not ESX 5.5 works as ESX 4.0 when the configs are also near identical, as I can make them and they are connected to the same switch?

  Thanks for any input you can provide!

  S

  This is the configuration for vhost1

  switch 1 (sw01)

  SW01 #sho run int port 3

  Building configuration...

  !

  !

  interface port-channel 3

  Description LAG for vhost1

  no downtime

  switchport mode trunk

  switchport trunk allowed vlan 1.8

  !

  end

  SW01 #sho run int 0/23 concert

  Building configuration...

  !

  !

  0/23 gigabit-switchport interface

  Vhost1 vmnic2 vswitch1 description

  no downtime

  channel-group mode 3 on

  !

  end

  SW01 #sho run int concert 0/24

  Building configuration...

  !

  !

  0/24 gigabit-switchport interface

  Vhost1 vmnic1 vswitch1 description

  no downtime

  channel-group mode 3 on

  !

  end

  vhost1

  [root@vhost1 ~] # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 03:04.00 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f4 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

  vmnic1 03:04.01 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f5 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

  [root@vhost1 ~] # esxcfg - vmknic - l

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk1 VMkernel - Server NetIPv4 10.1.8.31 255.255.255.0 10.1.8.255 00:50:56:78:9e:7e 1500 65535 true STATIC

  VMkernel - SAN Net IPv4 10.1.252.20 vmk0 255.255.255.0 10.1.252.255 00:50:56:7 c: d8:7e 9000 65535 true STATIC

  
  

  [root@vhost1 ~] # esxcfg - vswif - l

  Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE

  Service vswif1 - NetIPv4 management 10.1.1.12 console 255.255.255.0 10.1.1.255 true STATIC

  
  [root@vhost1 ~] # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  32 4 32 1500 vSwitch0

  Name PortGroup VLAN ID used rising Ports

  0 3 VM network

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch1 64 12 64 1500 vmnic1, vmnic0

  Name PortGroup VLAN ID used rising Ports

  Server network 8 7 vmnic1, vmnic0

  Console - management service vmnic1 Net0 1, vmnic0

  VMkernel - server 1 vmnic1 Net8, vmnic0

  On the Load Balancing vSwitch it Hash IP value.

  This is the configuration for vhost2

  switch 1

  SW01 #sho run int 4 port

  Building configuration...

  !

  !

  interface port-channel 4

  LAG description for vhost2

  no downtime

  switchport mode trunk

  switchport trunk allowed vlan 1.8

  !

  end

  
  

  SW01 #sho run int concert 0/17

  Building configuration...

  !

  !

  0/17 gigabit-switchport interface

  Description vhost2

  no downtime

  channel-group mode 4 on
  

  !

  end

  
  

  SW01 #sho run int concert 0/18

  Building configuration...

  !

  !

  interface gigabit-switchport 0/18

  Description vhost2

  no downtime

  channel-group mode 4 on

  !

  end

  vhost2

  ~ # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 0000:08:00.00 1500 c Intel Corporation 82574 L Gigabit Network Connection

  vmnic1 0000:09:00.00 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 d 1500 Intel Corporation 82574 L Gigabit Network Connection

  ~ # esxcfg - vmknic - l

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  Management 10.1.1.15 IPv4 network vmk0 255.255.255.0 10.1.1.255 c 1500 65535 real STATIC 00:25:90:e7:0e:9

  ~ # esxcfg - road - l

  VMkernel itineraries:

  Interface of network gateway subnet mask

  10.1.1.0 255.255.255.0 subnet local vmk0

  by default 0.0.0.0 10.1.1.1 vmk0

  
  

  ~ # esxcfg - road - n

  Expiration type neighbor Interface MAC address

  10.1.1.1 00:a0:c8:8 has: ff: 3 b vmk0 19m13s unknown

  ~ # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch0 4352 7 128 1500 vmnic0, vmnic1

  Name PortGroup VLAN ID used rising Ports

  Server network 8 1 vmnic0, vmnic1

  Management network 0 1 vmnic0, vmnic1

  On the Load Balancing vSwitch it Hash IP value.

  Hello

  Do you share the vmnic for ESXi management and network of the VM?

  Try to follow the steps in this KB: VMware KB: NICs using EtherChannel grouping allows intermittent network connectivity in ESXi

  Trying to team adapters using EtherChannel, network connectivity is disrupted on an ESXi host. This problem occurs because grouping NIC properties will not propagate to the network management portgroup in ESXi.

  When you configure the ESXi host for grouping of NETWORK cards in attributing to the road based on ip hashload balancing, this configuration is not propagated to the portgroup management network.

  Workaround

  Note: to reduce the possibility network loss please change the route based on the hash of IP using this method of balancing load vSwitch

  1. Close all ports in the physical switch team leaving a single port as active.
  2. Change the Route based on ip hash vSwitch and load balancing management Portgroup.
  3. Set up the physical switch port channel.
  4. Activate the physical switch ports.

  Notes: Using this method will avoid a loss of connection when you switch to a port channel. Also make sure that under the properties for vmk portgroup # used for network management you tick the box "Enabled".

• Dell Optiplex 745 with Broadcom NetXtreme 57xx Gigabit Controller with Windows 7 x 64 host cannot fill network

  All, I am new to the forum but have been reading up on top of a problem that had led me into a wall.

  I'm trying to create a development environment that uses VMWare Workstation 7.0.1 (and I tried with 7.0.0 before, leading me to)

  update in the hope of a quick solution) as a development of imaging and the test bench.  The system is a Dell Optiplex 745, upgraded to 8 GB of

  RAM.  Unfortunately, it seems that the biggest problem is the network card.

  I tried several different operating systems, and all DHCP requests are found in the AUTOMATIC private IP addressing.  This is even after I implemented a custom adapter (VMNet2) that fills explicitly to this network card problem.  I disabled VMNet0 and all because this dish was not working.  I have read some relevant

  messages, but nothing seems to help.  This included the http://communities.vmware.com/message/675649 and more

  positions listed on the registry settings.  I don't know what to do at this point.

  So, for those who do not know the Broadcom driver issues, they are apparently many.  It is important to disable the unloading, but

  I'm not able to find the settings in the post linked above.  It's quite similar to the OP for this thread.  I'm not

  know if it's a difference of conductor between the 32-bit and 64-bit implementations.  So, I updated from the version of the driver

  12.2.2.1 (b57nd60a.sys) of 10.100.0.0 (I think, can not driver rollback now to check because I need to work on VMS for urgent

  projects as soon as POSSIBLE).  So, as I said, I was unable to find the parameters of this post

  ()http://communities.vmware.com/thread/191085) mentioned below:

  • Large Send Offload (IPv4)

  • Large Send Offload v2 (IPv4)

  • Large Send Offload v2 (IPv6)

  What I found were these parameters:

  • Flow control (Auto, I tried to disable)

  • Priority and VLAN (priority & VLAN enabled; I tried priority and VLAN disabled)

  • Speed and Duplex (Knew better than to mess around here, has made the problems in the past, retired to Auto)

  • VLAN ID (always 0)

  • Wake Up Capabilities (Magic Packey; no one tried)

  • Unloading ARP (Enable; I tried to disable)

  • NS unloading (Enable; I tried to disable)

  I tried enabling / disabling all, specially those mentioning the unloading, all day without success.  This did not help.

  Later, I tried to add DontAddDefaultGateway, EnabledRSS and DisableTaskOffload keys to my CurrentControlSet on the

  host.  For some reason any DisableTaskOffload shows in the regedit, GUI, not the export of text.  Don't know what this means, and I'm too

  tired of care at this point.

  Host registry settings:

  Windows Registry Editor Version 5.00

  "ICSDomain"="mshome.net."

  "SyncDomainWithMembership" = DWORD: 00000001

  "NV Hostname"="HOME".

  "DataBasePath" = hex (2): 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f, 00, 6f,

  00,74,00,25,00, 5 C, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 D, 00, 33, 00, 32, 00, 5 C, 00,------.

  64,00,72,00,69,00,76,00,65,00,72,00,73,00 5 C 00, 65, 00, 74, 00, 63, 00, 00, 00

  "NameServer"=""

  "ForwardBroadcasts" = DWORD: 00000000

  "Domain"="domain.mei.contoso.com."

  'Hostname '=' HOME '.

  "SearchList"=""

  "UseDomainNameDevolution" = DWORD: 00000001

  "DeadGWDetectDefault" = DWORD: 00000001

  "DontAddDefaultGatewayDefault" = DWORD: 00000000

  "EnableWsd" = DWORD: 00000001

  "QualifyingDestinationThreshold" = dword:00000003

  "NV Domain"="domain.mei.contoso.com"

  "EnableRSS" = DWORD: 00000000

  "DhcpNameServer"="141.161.200.201 141.161.100.201".

  "DhcpDomain"="contoso.com".

  So, I'm not where that leaves me.  I am attaching a file vmx for a Windows XP (currently only started in WinPE) invited configured with bridged and IP information for the host and the guest.  If anyone can help me, I would be incredibly grateful.

  Guest VMX file:

  . Encoding = "windows-1252".

  config.version = '8 '.

  virtualHW.version = "7".

  maxvcpus = "4".

  scsi0. Present = 'TRUE '.

  memsize = '512 '.

  ide0:0. Present = 'TRUE '.

  ide0:0. FileName = 'Pharos PS.vmdk Test '.

  IDE1:0. Present = 'TRUE '.

  IDE1:0. FileName = "C:\Users\%username%\Documents\ISOs\peboot.iso".

  IDE1:0. DeviceType = "cdrom-image".

  floppy0.filetype = 'file '.

  floppy0. FileName = "autoinst.flp".

  floppy0.clientDevice = "FALSE".

  ethernet0. Present = 'TRUE '.

  ethernet0.wakeOnPcktRcv = "FALSE".

  ethernet0. AddressType = 'generated '.

  USB. Present = 'TRUE '.

  EHCI. Present = 'TRUE '.

  Sound.Present = 'TRUE '.

  sound.startConnected = "FALSE".

  sound.fileName = "-1".

  Sound.AutoDetect = "TRUE".

  MKS. Enable3D = 'TRUE '.

  pciBridge0.present = 'TRUE '.

  pciBridge4.present = 'TRUE '.

  pciBridge4.virtualDev = "pcieRootPort"

  pciBridge4.functions = '8 '.

  pciBridge5.present = 'TRUE '.

  pciBridge5.virtualDev = "pcieRootPort"

  pciBridge5.functions = '8 '.

  pciBridge6.present = 'TRUE '.

  pciBridge6.virtualDev = "pcieRootPort"

  pciBridge6.functions = '8 '.

  pciBridge7.present = 'TRUE '.

  pciBridge7.virtualDev = "pcieRootPort"

  pciBridge7.functions = '8 '.

  vmci0. Present = 'TRUE '.

  roamingVM.exitBehavior = 'go '.

  displayName = "Test Pharos PS"

  guestOS = "winxppro.

  NVRAM = "Test Pharos PS.nvram."

  virtualHW.productCompatibility = "hosted".

  easyInstall.keepFloppy = 'TRUE '.

  extendedConfigFile = 'Test Pharos PS.vmxf'

  ethernet0.generatedAddress = "00: 0C: 29:64:09:63.

  tools.syncTime = "FALSE".

  UUID. Location = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.

  UUID. BIOS = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.

  cleanShutdown = 'TRUE '.

  Replay.Supported = 'TRUE '.

  Replay.FileName = «»

  ide0:0. Redo = «»

  pciBridge0.pciSlotNumber = "17".

  pciBridge4.pciSlotNumber = "21".

  pciBridge5.pciSlotNumber = "22".

  pciBridge6.pciSlotNumber = "23".

  pciBridge7.pciSlotNumber = "24".

  scsi0.pciSlotNumber = "16".

  usb.pciSlotNumber = "32".

  ethernet0.pciSlotNumber = "33".

  sound.pciSlotNumber = "34".

  ehci.pciSlotNumber = "35".

  vmci0.pciSlotNumber = '36 '.

  vmotion.checkpointFBSize = "134217728.

  USB:0. Present = 'TRUE '.

  USB:1.present = 'TRUE '.

  ethernet0.generatedAddressOffset = '0 '.

  vmci0.ID = "1701054819".

  tools.remindInstall = 'TRUE '.

  USB:1.DeviceType = "hub".

  USB:0. DeviceType = "mouse".

  ethernet0.VNET = "VMnet2.

  ethernet0. ConnectionType = "custom".

  debugStub.winOffsets.version = "7".

  debugStub.winOffsets.value = "0 x 0, 88 x 84, 0 18 0 x 190 x, 0 x 174, 16, 416, 0x22c, 0 x 228, 0x1f0, 0 x 224, 0x20, 0x18, 0x18, 0x20, 0 x 24, 0x11c, 0 x 8, 0 0, 0, 4 x 0, 14 x 100000, 0xc, 0xc, 0x1b0, 0x18, 0x13c, 0x1f4.

  Host adapters:

  Windows IP configuration

  Name of the host...: TOWMI

  Suffix main Dns...: domain.mei.contoso.com

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: domain.mei.contoso.com

  Contoso.com

  Mei.contoso.com

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : contoso.com

  ... Description: Broadcom NetXtreme 57xx Gigabit Controller

  Physical address.... : 00-19-B9-38-5A-03

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::25cc:6bfc:91 has 9: d64d % 11 (Preferred)

  IPv4 address...: 10.205.3.136 (Preferred)

  ... Subnet mask: 255.255.254.0.

  Lease obtained...: Monday, 1 March 2010 16:00:06

  End of the lease...: Tuesday, March 2, 2010 16:00:05

  ... Default gateway. : 10.205.2.1.

  DHCP server...: 141.161.200.213

  DHCPv6 IOOKING...: 234887609

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers...: 141.161.200.201

  141.161.100.201

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet1:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet1

  Physical address.... : 00-50-56-C0-00-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::ace9:b312:d32d:fb39% 16 (Preferred)

  IPv4 address...: 192.168.58.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 352342102

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet8:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet8

  Physical address.... : 00-50-56-C0-00-08

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::1c44:4e88:3178:4ccf % 17 (Preferred)

  IPv4 address: 192.168.168.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 369119318

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {4EF89CD9-7A7D-4B80-83C5-A56D5FA6D748}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft ISATAP adapter

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 9:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {E03C7ECA-35DF-43C6-BCC8-08D2BB8E4233}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #2

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter ISATAP.contoso.com:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. : contoso.com

  ... Description: Adapter Microsoft ISATAP #3

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Adapters of comments:

  Windows IP configuration

  The host... name: minint-et0ko7r

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :

  ... Description: VMware accelerated AMD PCNet Adapter

  Physical address.... : 00-0C-29-64-09-63

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::8842:488e:b75:ec51 %2 (Preferred)

  Autoconfiguration IPv4 address. . : 169.254.236.81 (Preferred)

  ... Subnet mask: 255.255.0.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 33557545

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  See also my VNE screen capture and sample log file attached.  Thank you very much in advance for any help.

  Sorry, had to rub a small part of the newspaper for my own protection.

  Post edited by: alharaka

  I'm sorry, I completely forgot to reply to this topic yesterday (get distracted by a matter of work).    I'll be back today and noticed that you have marked this as answer.  The root cause of the problem was therefore one MAC address per port restriction put in place by your network management team?

• Framework of biometric Latitude E6420 - Broadcom USH drivers windows

  Hi experts,

  Ask you to check this old_post

  http://en.community.Dell.com/support-forums/laptop/f/3518/p/19485564/20278666.aspx#20278666

  I have the same problem, even after you have reinstalled the drivers in the order as suggested by Dell.

  

  I installed "CV_WBF_Setup_Y2GT8_64bit_ZPE.exe".
  [1] double-click on the .exe with option of compatibility in windows 7 and the checkbox on the value

  run as administrator (best option).
  [2] click on ok for a Floder pop-up.
  [3] now install you the driver (this will clear the yellow color material highlighted in)

  Device Manager)
  [4] reBOOT and then install the Firmware (set to the same level provided firmware along

  with driver).
  [5] reboot-> connection (with password :-|) and verify biometric devices in control pannel.)
  you try to check biometric devices in Control Panel and lettering.

  you might get the ERROR below:
  "configuration of broadcom ush host components BrcmFMA.exe - by-side is incorrect.
  Details correct as below:
  Activation context generation failed for "C:\Program Corporation\Broadcom Broadcom

  USH Host Components\BrcmFMA.exe. Dependent assembly

  Microsoft.VC90.MFC, processorArchitecture is "amd64", publicKeyToken = "1fc8b3b9a1e18e3b", type is "wi

  N32', version = '9.0.21022.8' not found. Please use sxstrace.exe for detailed

  diagnosis.

  solution is to install Microsoft Visual C++ 2008 SP1 Redistributable Package (x 64).

  now the problem is that the finger print data are saving :(
  I continued to ask dell support team.
  the big joke, it's what they call it as OFF FIELD.
  :(

  Crazy technical support

  Hi guys,.

  Please see the link below.

  http://en.community.Dell.com/support-forums/laptop/f/3518/p/19485564/20338375.aspx#20338375

  Answer posted by "" P3Sal " "

  OK Dell has finally released drivers for Windows 8.  Its a few steps so here's how I worked on all our machines.

  Uninstall the Dell Data Protection if you have it installed.

  Download the firmware and driver here:

  Driver: www.dell.com/.../latitude-e6420

  Firmware: www.dell.com/.../latitude-e6420

  Extract the firmware and install it.  You must run it in high command line and be sure to select the x 64 Installer.

  Reset

  Once installed, you can install the driver from Dell ControlVault

  Restart and you should now see the biometric device.  The software will be Broadcom now instead of Dell and you can save your fingerprints.

  Kind regards

  Ralu

• How to automatically send an sms to the team?

  I would like to know if there is a way (setting) or an application that can automatically send an sms (txt) to my team?

  A 3rd party app called IFFT may enforce an assortment of things, among them actions based on SMS.

  For some recipes, as they call it, take a look on their website: https://ifttt.com/sms

• This e-mail from the thunderbird support team or a fake email?

  I received an email informing me that my account is almost full and giving me instructions on how to renew my account. I just want to check if this e-mail is really a mozilla thunderbird support or is a fake email.

  the content of the email:

  Subject: [[email protected]] alert low storage limit
  Date: Thu, October 15, 2015 17:00:08-0700
  From: < [email protected] > Service account
  Answer: [email protected]
  To: [email protected]

  Dear [email protected],

  1969-2000 MB

  We noticed that your e-mail account has almost exceeds its limit. And you will not be able to send or receive messages any time now,

  Click here to renew your account.

  NOTICE:
  failure of the renewal of your e-mail account. It will be permanently disabled.

  Thank you
  Service account

  n ' has not clicked on the hyper suggested link again.

  The wording of the messages from the 'provider' is a little off. It may be a phishing attempt.
  Contact your e-mail provider using the details found on an old Bill or use a previous contact address you have used successfully in the past.
  DO NOT CLICK ON LINKS IN THE MESSAGE-UNSUB
  
  
  
  The messages appear to come from - [email protected] , but the reply address is another area - [email protected].
  
  The address of this last was reported as scam
  http://scammed.by/scam.php?id=77518
  
  
  Your question

  This e-mail from the thunderbird support team or a fake email?

  Thunderbird support is not a provider of e-mail and does not send a message like this. I suspect that it is a scam.

  TB - 38, 3 Win10-PC