Brocade M5424 Fibre Channel blade switch fiber?

Similar Questions

• Fibre Channel SAN / switch?

  can I use a 4200 ProCurve switch with optical modules to connect to a 3 host vmware SAN fibre channel?

  or I need to switch dedicated to SAN?

  My SAN is an Eternus DX80 with 2 fiber channel controller.

  Thank you too much.

  ProCurve's network switch.

  Data a switch needs dedicated, you can't mix and match network with data traffic.

• OME 2.0.1 and Brocade M5424 fc switches

  Hello

  I have problem with OME discovery/inventory abd Brocade M5424.   4 M5424 brocades are defined as 2 M1000e chassis access gateways, problem is this discovery/inventory OME found as a fibre channel switch with 4 ip addresses.

  Inventory and discovery works well with all the other components of these 2 chassis, only fc switches I have this problem.

  M5424 have unique host names, single ip addr. and snmp is defined.  OME same troubleshooting tool gives me the correct result when the connection on these switches CF test.

  Anyone with the same problem?  Mode gateway may be the source of this problem?

  Thanks for any help

  Martin

  
  

• Can I disable the B200 blade Fibre Channel vHBA

  Hello

  I'm setting up my service to my B200 blades profiles and I was wondering if there was a way to disable the Fibre Channel HBA. I will not use CF as all my iSCSI storage.

  Thank you

  LTA

  When you create a service profile, you are asked if you want the storage (= CF) or not; you say no!

  If you missed this step and you have created vhba, just remove them later.

  It is not possible to disable vhna.

• Fibre Channel card configuration on the host esx 5.1

  Hi all,

  I have three 5.1 esxi hosts.  I have new port 2 8G Fibre Channel cards installed in each and pass the cable FC since the card port goes to the fiber.

  It's my first time in collaboration with CF cards VMware hosts, what else should I do for these cards to be active or updated network in?  A good explanation, Docs and or video would be extremely welcomed.

  Just ask EMC technology to make the zoning on the SAN switch and the LUN masking and card introduced volumes to your hosts on the side storage... after the volumes, simply go to your ESXi, rescan your HBA and create data warehouses.

• 4.1 and vCenter ESX only allows to use 1 Fibre Channel LUNS

  Hello

  I have 8 blades ESX 4.1 (build 348481) in a Cisco UCS 5108 chassis. Each blade has 2 x HBAs available. I also have a fiber channel storage array that is configured to provide 2 1.8 to LUN (for now and in the future).

  When I go in vCenter and select one of the ESX servers under "Configuration"-> "Storage adapters"-> "Rescan all...» "each server detects the table (and several paths towards it) but only shows a single available LUNS (LUN 0) when 2 LUNS should be available (LUNS 0 and 1 logical unit number). See the image below.

  

  Now, the thing that confuses me is that when I get on the command-line of the ESX via SSH server and run "esxcfg-mpath - b", I see a list of all the paths including the paths to the LUNS 0 and 1 logical unit number (see output below). Any ideas on why ESX and vCenter authorizes me to LUN 1?

  esxcfg-mpath - b:

  NAA.600508e0000000001e10a036bc3f5601: FREE Serial Attached SCSI Disk (naa.600508e0000000001e10a036bc3f5601)
  vmhba0:C1:t0:l0 LUN:0 Status: active sas adapter: 5c84c75ed0910000 target: 1563fbc36a0101e

  MPX.vmhba32:C0:t0:l0: Local USB CD-ROM (mpx.vmhba32:C0:T0:L0)
  vmhba32:C0:t0:l0 LUN:0 Status: Active Local HBA vmhba32 channel target 0 0

  EUI.706f636c6162766f: disc SCST_FIO Fibre Channel (eui.706f636c6162766f)
  vmhba2:C0:T1:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f2 WWPN: 21:00:00:24: ff: 32:10:f2
  vmhba2:C0:T1:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f2 WWPN: 21:00:00:24: ff: 32:10:f2
  vmhba1:C0:t0:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c2 WWPN: 21:00:00:24: ff: 32:45:c2
  vmhba1:C0:t0:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c2 WWPN: 21:00:00:24: ff: 32:45:c2
  vmhba1:C0:T1:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c3 WWPN: 21:00:00:24: ff: 32:45:c3
  vmhba1:C0:T1:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c3 WWPN: 21:00:00:24: ff: 32:45:c3
  vmhba2:C0:t0:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f3 WWPN: 21:00:00:24: ff: 32:10:f3
  vmhba2:C0:t0:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f3 WWPN: 21:00:00:24: ff: 32:10:f3

  MPX.vmhba32:C0:t0:L1: USB Direct-access locally (mpx.vmhba32:C0:T0:L1)
  vmhba32:C0:t0:L1 LUN:1 status: Active Local HBA vmhba32 channel target 0 0

  MPX.vmhba32:C0:t0:L2: USB Direct-access locally (mpx.vmhba32:C0:T0:L2)
  vmhba32:C0:t0:L2 LUN:2 status: Active Local HBA vmhba32 channel target 0 0

  Its because the table shows two LUNS have the same value of ID of Page 83, ESX both think you have 2 paths to the same LUN.  Paths multiple ESX driver uses the value of the ID of Page 83 to determine if 2 LUNS are the same device.

  It was a problem with that code, that it resembles yours-based Solaris beginning according to the tables and other tables that used code based on Solaris pre-COMSTAR, as well as tables that use SCWIST.

  There is really nothing you can do about it, because it is a bug in the software of the array (it shouldn't be exporting 2 LUNS different with the same ID value of Page 83 - it is a violation of the standard).

• Unable to access QLogic Fibre Channel HBA

  Hello

  We have RHEL4 on a Virtual Machine. We are using VMWare Server 2. Host operating system also is RHEL4. Material is Server Blade Qlogic Fibre Channel HBA. We have HP EVA SAN attached is this server blade and some virtual disks are presented.

  I also want to access SAN on a Virtual Machine, unable to detect fiber channels. I installed the QLogic on Virtual Machine driver.

  Help, please

  Try to add a SCSI device to passthrough at the prompt (when turned off).

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Problem with XServe and XServe RAID via Fibre Channel

  Hello everyone,

  I have a problem with my blended Xserve RAID.

  I see in RAID-Admin and configure it successfully (via Ethernet). Connect with our Xserve via Fibre Channel, but the XServe and XServe RAID do not detect each other.

  The fiber on the Xserve channel LEDs are white on the Xserve RAID completely off and permanent.

  RAID-Admin status of Fibre Channel: 'No connection (1 table)' with a red square.

  If I try to open the utility of fiber channel I get the message: "card Fibre Channel is not found." Utility disk OS X can't, too.

  I changed the card connector cable, and made several reboots. But each time the same thing: they do not detect each other.

  Xserve (2009):

  -2.26 GHz Quad-Core Intel Xeon 5500

  -Map of Apple dual-channel 4 Gb Fibre Channel (LSI7204EP)

  XServe RAID:

  -RAID 5 in an array (only on the left with 5 x 500 GB)

  -1.5.1 Firmware

  -Cable Apple 4 Gb SFP - SFP

  Thanks for your help and sorry for my bad English!

  Hi Mpm-Mainz,

  Check if you have enabled LUN masking. To be able to see, you will need to download raid admin 1.5 not the 1.5.1

  Xserve RAID Admin Tools 1.5

  Have you also tried to use the other controller? Even if there is no disc in there, then it should appear in the preferences of fiber card system.

  Thank you
  Owen

• Uplink Ports Fibre Channel - UCS GUI Configuration Guide

  Hi all

  Could someone please explain which means that what follows in the Configuration of GUI of UCS guide @.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.PDF

  Uplink Ports Fibre Channel

  Manage ports Uplink Fiber Channel FCoE traffic between the interconnection of fabric and the next layer of the

  SAN storage network. All FCoE network-related traffic is pinned to one of these ports.

  By default, the Fibre Channel ports are uplink. However, you can configure them to work as Fibre Channel

  storage ports. This is useful in cases where a Cisco UCS requires a connection to a DAS storage

  Device (DAS).

  My question is, how the FC Port could handle FCoE traffic? My understanding was that FCoE will be lifted and Enthernet connection only.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.PDF

  Thanks for your help

  Concerning

  Vikas Srivastava

  The CF module interconnection fabric is the place where the speration of CF vs. FCoE happen, so it's where the FC frame is extracted in the Ethernet frame.

• Fibre Channel frames - UCS

  I was wondering if it really is possible to have the Fibre Channel frames running on a UCS?

  I read these two articles that provide some great information on the implementation of the Fiber Channel Jumbo and Jumbo frames:

  http://datacenteroverlords.com/2013/04/01/Jumbo-FC-frames/
  http://www.ccierants.com/2013/10/CCIE-DC-definitive-Jumbo-frames.html

  Everything in the SAN I'm administration has the ability to set the MTU value until 9036 except for the UCS. For example on NetApp train I can set the MTU by interface on the Cisco MDS I can set the MTU by vsan. However in the UCS Manager when I go to class of service of system quality, the option to set the MTU of Fibre Channel value is grayed out and it doesn't look like there is in any case override the preset frame size. I can set the MTU of the best Effort however my understanding is traffic Fibre Channel in the UCS will use the class system of Fibre Channel.

  Also I noticed that I can set the maximum size of the data on the vHBA field in the UCS Manager but my understanding is the maximum that can be up to 2048.

  Hello

  Have you checked

  http://datacenteroverlords.com/2013/04/01/Jumbo-FC-frames/

  Erik Smith says:
  17:52, 1 April 2013

  April fool! I wish I saw this earlier, I would have posted corroborating results!

  In short: Forget the CF frames!

• Brocade 815 fibre cards not no projection in section storage adapters?

  Hi all

  We just bought two new Dell r.620 Dell with two Brocade 815 servers, single Port 8 Gb Fibre Channel cards in them.  I'm fighting to make them appear in the section configuration of vSphere storage cards (5.5 Update 1).  At first I though this might be because they was disabled on the server.  I went into the BIOS and enabled them now, but still nothing.

  Someone at - it ideas that I'm running on the ideas!

  Thanks in advance

  try to download the following driver and install it. According to the VMware HCL, this is the driver for Brocade 815.

  VMware vSphere 5: Private Cloud Computing, server and data center virtualization

• 10GB Ethernet - Fibre Channel

  Most of my clients can hold 10 000 to 15 000 ther budget for:

  Storage

  Infustructure network

  HBAs for ESXi host

  Are there tool or a way to find solutions for businesses who want to enter the field with Essentials more, but because of the e/s, we need more storage gigabit NIC.

  Is the next logical leap of 1 gigabit 10Gbe? Or is it Fiber Channel?

  Hey...

  "fibre channel" is essentially a storage architecture...

  You are considering fiber ethernet by opposition to the copper perhaps?... 1000BASE-SX or LX for example...

  That there is no increase in bandwidth over copper gigabit... It is used to connect longer distances, copper CAN... or connect two buildings where a connection copper between two buildings with two blocks of independent electricity is against the regulations (it is the case in the United Kingdom),

  The next viable step upwards of copper gigabit "done, team/shared resources" several gigabit copper... or 10GBE which maybe more fiber or copper.

  We use dual 10GBE fiber in our ESX host and our Center database to the production and satellite floor data centers.

  Hope that helps... after if is not the info you wanted... :-)

• Fibre Channel vs. Fibre Channel over Ethernet

  Hello everyone,

  Have questions about storage of this connection technology:

  1. what kind of cards are required for the FC and FCoE?

  2. do I need these adapters on both sides, server, and storage?

  3. what switches and cables are required for the FC and FCoE?

  Thnx in advance

  Yerkoff

  Yerkoff wrote:

  1. what kind of cards are required for the FC and FCoE?

  FC = Fibre Channel HBA Qlogic QLE2462 or OEM of Emulex.

  FCoE = cards of convergent network (http://en.wikipedia.org/wiki/Fibre_Channel_over_Ethernet)

  2. do I need these adapters on both sides, server, and storage?

  HBA is required on the server. They connect to FC switches. The switches connected to the SAN, who also has the appropriate maps build-in.

  3. what switches and cables are required for the FC and FCoE?

  FC switches

  Cables could be Multimode, multimode or copper.

  AWo

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• It is possible to contact PCA9548A (8-CHANNEL I2C SWITCH) using USB-8451?

  Hello

  Now, I'm doing a project related to the smart battery. Now, I read data from a stack using the USB-8451 by smbus. The next step uses the USB-8451 casing to read the data of several batteries through smbus. I chose the PCA9548A (8-CHANNEL I2C SWITCH) to achieve this goal. But when I check the specification of the PCA9548A, there is a fix I2c format to read data from it, I tried several times, but still no can tell me where is the error in my code, or maybe it's impossible to communicate with this chip using USB-8451?

  Here is the fix that i2c read format of PCA9548A

  Why are you usng the script live? Have you looked at the examples of delivery for the 8451? You just need a couple of nodes property to set the rate and the address, and then use the VI to write I2C.

• Emulator of the UCS and Fibre Channel (PCI Passthrough)

  Hello

  I would like to know if anyone of you knows if emulator UCS supports CF communications and how to configure them.

  I have 2 PCI Fibre Channel interfaces on the host Hardware and I applied PCI Passthrough on the ESXi hypervisor. It works with other virtual machines.

  Thank you very much

  Francesco

  No, unfortunately not.