Bus / effect Solo

Similar Questions

• PowerCore Plug-ins are not represented in exports?

  Maaaaaaannnnnnnnn! I was just starting to forgive Audition CS5 for the botomy feature that he shot at us. Does anyone else get this problem? I use a TC Electronics PowerCore plug-ins, which, similar to the UAD plug-ins are treated using a PCI-e card. I can turn on plug-ins in CS5.5 and hear while I mix. But when I try to export my mixture, they aren't there. It even seems that if I had disabled all of my plug-ins PowerCore right before I exported. And it doesn't matter which of them I use. It does not include any of them in the export. I tried several solutions workaround... mixing bus effects first, the mixture down the bus master, do a session overall, pre-made tracks export, etc. Does not work. It's all the same. A mix beautifully lamppost and compressed exports completely dry and punchless. And it doesn't seem to be what I can do about it. Everyone can check what happens, and does it affect other plug in third-party PCI cards? Any ideas for a fix?

  Hello

  Matt here from the dev team.

  It is not multitreading that is the cause but the fact that the multitrack clone us when we make a mix.  The enthusiasm of the thread will not make a difference.  So, if you use 1 DSP chip, when we realize a mix, we will use two (the original used during the mix and a mixing cloned one for new).

  This works well when you have virtually unlimited of instances of plugins available with native effects, but can lead to audition 4 fills a hosted card with double effects fast enough.

  The infallible only work around would be to trade securities finished to new tracks and dissable the original titles that rely heavily on the hosted effects.  Or, you could just make sure that you have enough free DSP left in the Powercore to restore down.

  -MattS

• Effects bus

  My guitar tutor asked me not to include the effects upon registration of securities, but to add as own and then add effects on a bus.  I wasn't quite sure what he meant, so when I got home I couldn't find anywhere to do this.

  Can someone advise?

  On the subject of GarageBand, has nothing to fear, because she always saves the original 'clean' signal as it is without adding effects. All the effects that you add with plugin in GarageBand, even if you hear while recording, are added to the 'read' signal', 'monitor' with effects without actually their registration. This is why you can change the sound in any way at any time after registration.

  However, if you save a processed signal (physical real pedals add to your guitar sound and record this signal, then of course, this signal will be recorded like that and you can't 'make clean again').

  Bus

  CE that your professor is referring is an audio production technique, where you (route) also send part of the signal on a track to another track (called a track to the) via a so-called 'Bus', add an effect on this track to the (reverb, delay, etc.) and mix two signals of tracks depending on how the original signal and how much the signal effect you want.

  GarageBand has no bus (at least not outdoors). Any effect you want to add is done by adding Plugins directly on the track, not need to bus. (An exception is Master effects).

  Hope that helps

  Edgar Rothermich - LogicProGEM.com

  (Author of "Graphically improved manuals")

  http://DingDingMusic.com/manuals/

  "I could receive some form of compensation, financial or otherwise, my recommendation or link."

• question on the bus

  I am using parallel compression these days, and I have a few questions about the different ways of doing in the hearing.

  * The first is to clone the voice (for example) to a second clip on a second track and compress the hell out of it and adjust the levels to taste.  It works fine, but there are two drawbacks.  First of all, if I want only it EQ'ed the same way as the main vocal track, I have to run another parametric on the second track, and which relies on the resources of the computer.  Another disadvantage is that if I adjust the level of the main voice, I have to also then twist the compressed track level.  It would be nice if I could somehow lock the levels of the two tracks so that if I adjusted one, the other follows automatically adapt.  Is this achievable in hearing?  I think not, no?

  * The second way is to send the vocal track to a bus and compress the hell out of him.  The problem here is that if I turn down the level of the vocal track, it's less compression happening on the bus, so it changes the sound.  To keep the same knotty summarization level on his bus, I need to change the threshold.

  OK, is there a way to do what I want to do that I didn't think?  I want to be able to adjust the level of the voice and have the same relative amount of compression on the parallel track/effect.

  As you have discovered, auxiliary melted pre have tend to be 'pre top to pass off' as model on hardware mixers.  For many / most of the applications, it is desirable.

  For example, auxiliary fade before direct work is mainly used to feed on onstage.  Often you do not want to lose her even if you solo a different channel in your headphones to check a problem of microphone or something.  In situations where you MUST keep silence all that feeds the Meadow melted to the, simply turn off the output - for example, on a show that I did recently, there was a fade to silence, I had to perform live and it was necessary to fade the monitors on stage too or the public would still be listening to music there although the FAÇADE was silent... I just pulled down from the monitor output at the same time I was stumping the FOH.

• Memory Bus speed

  I have 3 portable C771US.  Each of them has 2 GB of memory (2 x 1 GB of DDR2-667 PC 5300).  If I make a diagnosis at startup, the system shows the bus memory running a 533 MHz.  Everest shows the real clock of front side bus to 133 MHz with an effective 533 MHz clock.  It also shows memory bus clock properties real 266 MHz with an effective 533 MHz clock.   Everest has also indicates that the memory factory runs on the timing of the SPD to 266 instead of the programming of schedules for 333.

  The mobile Intel 965 Express GM chipset and processor T2390 supports an effective bus of 667 MHz (real 333 MHz clock) speed.   HP also has required as PC5300 DDR2-667 memory running at 667 MHz (333 Mhz).

  Why has HP/Compaq strangled the speed of the memory on this laptop model?  This seems to be the result of a bios incorrect memory calendar/type definition (not accessible to end users).

  I guess that's the reason for the low side of Windows Vista experience from 4.4 to memory.  As the graphical subsystem sharing the main memory, the graphics score 3.1 (3.3 games) is probably lower than it might be as well.  As this is a portable value, I can only assume that the parameters used by the BIOS have been forgotten or were a conscious decision of marketing in order to protect the higher finished goods.

  I hope it wasn't the last.  What about an update of the bios to remedy or better yet an update of the bios that allows the user to adjust the memory timings.

  Kind regards

  Tom

  Message edited by ThomasWilson on 11/17/2008 19:31

  My mistake.  T2390 processor has a speed of 533 MHz fsb.  I accidentally lifted the incorrect CPU specs. I upgrade the processor to reach 667.

  Kind regards

  Tom

  Message edited by ThomasWilson on 11/18/2008 19:28

• CPU frequency and bus on Satellite M30 is too low

  Hello

  The processor and my Satellite M30 bus seems to be significantly under speed. According to Windows XP Pro and Solaris Nevada, the processor is clocked at 600 MHz. The frequency of the BIOS, scaling parameter is set to "Still high", and I tried to disable ACPI in the operating system (ensuring no interference on the software side), without result. Power in the Toshiba Power Saver settings are all maxed out, so no scaling should be there either. Intel Processor Identification Utility reports the following:

  Reported expected
  Speed: 1.60 GHz GHz 0.44
  System bus: 400 MHz 294 MHz

  Note that the tool uses algorithms to determine the speed, rather than trusting the value returned by the operating system, that one of her aims purposes is testing for fraudulenty CPU overclocked by OEMs. The speed as it is for me is even more disappointing. I don't know how long it has been like that, but one thing to note is that the motherboard has been replaced last summer.

  Someone has an idea what here? Thank you.

  Edit: I also loaded the CPU with CPU-Burn to see if some heavy loads would get understandingly frequency. It has no effect.

  Hello

  If you use the advanced search option, you will find a few similar topics with the explanation very clear why unit works with 600 MHz only.

  In any case, after the replacement motherboard service must blink mainboard firmware. After doing this it will work at full speed. Because of this, I guess they forgot to do.

  It is not a big problem. Please contact again and explain the situation.

• Can I replace the memory and not lose what is on the old memory for a Mid 2007 Mack computer desktop Intel Core 2 Duo, 2 GHz processor speed, 1 CPU, 4 MB of Cache L1, the 4 GB memory at 800 MHz bus speed.  Only 1 slot can play memory, the other is damaged

  Can I replace the memory and not to lose what's on the memory of the former?  I have a Mid 2007, 20 "desktop Mac, Intel Core 2 Duo, 2 GHz processor, 1 CPU, 4 MB L2 cache, 4 GB of memory, 800 MHz bus speed.  I have a backup device.  A RAM slot is damaged.

  You are confused of RAM and disk space available.

  RAM stores information temporarily while the Mac is enabled and the application is reached. RAM replacement has no effect on the long term of your information storage.

  The hard drive is where your information is stored in the long term. If you replace your hard drive, you need restore the information from a backup.

  FYI, for your iMac, the maximum RAM is only 6 GB.

• Satellite C870D:Network / SM-Bus-controller not missing, no WLAN/inet

  Hi Toshiba,

  I demoted Win8 to Win7on the C870D PSCBEE satellite. After so much success, both pilots are still missing:

  * SM-Bus-controller *.
  * Network controller *.

  _Effects: _

  -no available WLAN, my home network is not displayed, press F12 has no effect
  -no internet connection

  + Curious side effect: + I was able to connect to my home dsl / phone to to run my Windows Update.

  I already tried to install several drivers controller Toshiba drivers network on the theme section / WLAN.
  No effect.

  Who could help me? What stage is missing? Where can I find the drivers above?

  Help much appreciated.
  Thank you very much for your time.

  Cheers, Nic

  Solved.

  * Source for the SM BUS driver: *.

  http://www.Toshiba.de/innovation/download_drivers_bios.jsp?service=de?service=de

  Here, I found the display driver for my laptop. It contains the required file of SM - BUS, too.
  In addition, section driver Toshiba offers the right WLAN driver.

  * Probably useful: *.

  Installing a new bios. Next time, it will be my first step.

  Cheers, Nic

  Post edited by: Nicsmix

• Equium L40 - 10Z - Microsoft UAA for High Definition Audio bus driver need

  OK, this is what s up. I uninstalled Vista of the laptop and installed Windows XP Professional (5.1, Build 2600) Service Pack 2. All the drivers I installed works fine except my audio driver. There is no sound.

  I installed Realtek several times and it installs ok then restart to take effect, but when I restart there is still no sound. Driver installed is listed in Add/Remove programs. I tried for almost a week now to fix this problem and nothing happen.

  The pilot was MICROSOFT UAA BUS DRIVER for HIGH DEFINITION AUDIO with a yellow (!) next to it. When I tried open Realtek he said EQ failed or Summit and s there is a sound beep sound from the laptop.

  Toshiba virtual sound doesn t work as well. I accidentally uninstalled the driver and now it says device PCI and tells me to insert the disk MICROSOFT UAA BUS DRIVER for HIGH DEFINITION AUDIO but I n t I.

  It s been driven crazy and I don't know what to do.
  Please help me!

  Hello

  first of all, make sure that you have installed all the important windows updates. All the updates on your system? Ok.

  Please visit the www.realtek.com site and download the latest driver for realtek HD sound cards. This driver WORKS 100% because I had a similar problem and after I installed the authentic realtek drivers, I had no problem with the sound.

  Hope this works for you, too.

  Welcome them

• is there a way to specify instructions to bus?

  is there a way to specify route bus only in the cards of Apple?

  Writing an effective question of communities of Apple Support

• PXI-8512/2 XNET CAN stops when bus errors occur on Spadina

  Hello, I use the PXI-8512/2 in a noisy electrical environment so I often get errors on the CAN bus. I noticed that often 8512 stops communicate. In my dual port 8512/2, 4, # LED that flashes normally will eventually turn off. However, I have other devices listening on the same bus; report errors, they continue to stay alive. Is there anyway that I can get the 8512 continue to work in the presence of errors? I use the custom device XNET for VeriStand 2009 and do not see the error handling options. In fact, I don't get any notification of errors at all. I just noticed that my incoming CAN stop signals and my leavers have no effect. Thank you.

  Hello

  You shouldn't have to remove from your devices.  Just update the configuration and engine llbs and restart the Explorer system, save your configuration and redeployment.  Let me know if you see problems.

  (There are new files also copied into the directory of device custom if you want to use the bus monitor function... so you can replace the entire record of the NOR-XNET if it's easier).

• Workstation PC with full PCI (ie. 256) buses numbering?

  Hello!

  I have a problem with DELL Optiplex 7010 and two bodies SMU connected to it like this:

  Port of PC PCie8372 1-3 metres of cable-> SMU - 8370 >-> the 1 SMU-1065 chassis

  port 2-> 3 metres of cable-> SMU - 8370-> the 2 SMU-1075 chassis

  Problem is that in Windows nipxirfk event log service complained that "PCI Host Bridge: bus Maximum number limit reached before listing all devices, status =-313563 '.

  When I tried different things to solve the problem as withdrawal PCI GPIB bus and change SMU bodies on different ports on PCIe card, half of PC USB ports have stopped working and when I changed something the other half stops working

  PC has limited the availability of bus numbers:

  8< -="" -="" -="" -="" -="" -="" -="">

  = Detection of resources OR root Bus utility =.
  This utility determines the number of root PCI/PCI Express bus
  devices on your system and if there is any number of bus
  range limitations that could cause equipment problems.

  = SUMMARY =.
  Bus single root detected.
  Your system has a single root PCI bus.
  Bus root has a limited scope.
  The BIOS of your system has a limit on the number of bus range
  You can assign to your PCI tree. In Windows XP, this limit is ignored
  and has no effect. In Windows Vista and later versions, the limit is strictly
  applied and cannot be exceeded. Thus, the amount of MXI-Express
  You can reach the material is limited. Refer to the number of bus range
  below the limits of your system.

  = DETAILS =.

  -Root Bus: ACPI\PNP0A08\0 -.
  Bus numbers range: [0, 3]
  Status: Device is running

  This utility ran without error.

  8< -="" -="" -="" -="" -="" -="" -="">

  So I take is not enough PCI bus available on this PC to allocate sufficient resources for all connected devices. There is nothing BIO on bus PCI PC I could delete or nothing to what I could turn off, actually, I have to back PCI GPIB card and who will eat resources. The two bodies SMU are about half full of instruments and I need to add more than a few cards to one of them. PC BIOS is up to date. I was sort of the details with the support OR already, but they do not have solution. Our laboratory has two former HP/workstations DELL (is no longer available) with the limited numbering PCI bus that work with the same two bodies very well. I think that this problem is PC related BIOS and my computer is right on the limit of not working.

  Basically, I need to know a few current PC workstation, used successfully to control at least two 2 SMU bodies. If you could check you workstation PCI bus numbering capacity with this tool EITHER:

  http://digital.NI.com/public.nsf/allkb/BF84B75E08D2A7708625763B00670007?OpenDocument

  And display the results here, I would be very grateful.

  Jan,

  Some Dell BIOS have an option to set the number PCIe bus max.  A lower number allows more usable in a 32-bit operating system memory.  I saw him in some positions as the T3600 precision work.  On these machines, you access the BIOS and go to system Configurationoption"Configuration of the PCI Bus, and then change the value to something higher (such as 256).  Can you check for this option?

  -Robert

• CAN frame API with two bus

  Hello

  I use a PXI-8461 to control 2 CAN bus lines.

  When I run the bus monitor to the MAX, both work correctly (frames are coming).

  But I lost a day now to try to make the two lines operate in my application.

  I call ncConfigCANNet.vi and ncOpen first with CAN0, then with CAN1.  ncOpen with CAN0 gives me an objHandle, but when I ncOpen cann with CAN1 after that, I get objHandle = 0 but no error!

  (I do not use error entries)

  So in my application CAN0 is running, CAN1 finally returns an error when I try to read using the objHandle (s is 0).

  I even tried to use the example of NEITHER "Multiples CAN Frame API maps unique DAQmx map Input.vi" with the same effect.

  Is there a known issue with this subject?

  I use

  NI-CAN 2.7.2f2

  LV 8.5.1

  PXI8461 with CAN0 and CAN1 working with the MAX busmonitor

  100g Ritter Sport chocolate / hour

  Sorry, my fault.

  I was able to solve the problem. My length of read - and write-queue was too big. I was using 100 for each queue. This works for a CAN interface, but not for 2. And, Yes, there is an error message... I lost this error somewhere in the error handling.

  Something beautiful that I used for the first time here is the network debug function for the executable files. Really cool and useful.

  Detective Conan!

• How can I get the Bus IEEE 1394 Host controller driver to show up in Device Manager?

  I try to activate my new Firewire Interface M-Audio Solo and I encountered a small problem.
  I recently bought a PCI card on eBay and I hope that it is not defective because even if the blue light on my Solo M-Audio lights when I insert it into the firewire port, I don't see this pop up on my computer screen. In addition to this, I discovered that the Bus IEEE 1394 Host controller is not installed on my computer (Windows XP)...
  Can anyone help please?

  Of my experience with the installation of port expansion cards (USB, Firewire, etc.), they always require facilities suitable driver to work properly.  The card comes with an installation disc, or have some sort of instructions for you inform to download the latest drivers for the device from the manufacturer's website?

• HP 15-d030nr: what updates what I need to do in order to use Adobe After Effects CS6?

  HP 15-d030nr, which updates what I need to do in order to use adobe after effects cs6?

  I installed Adobe After Effectss CS6 because the HP Support told me that he would continue to operate; This isn't.  It is very slow and locks up bad.  What updates what I do, or I'm looking to have to go buy another labtop?  Also, I can make these upgrades me - at what price?

  * HP 15-d030nr *.

  Material

  15-d030nr product name

  Product number F5X99UA

  Microprocessor 2.0 GHz processor Intel Pentium N3510

  Microprocessor Cache 2 MB L2 Cache

  4 GB memory (1 DIMM) SDRAM DDR3L

  User accessible memory Slots 2

  Intel HD graphics graphics video

  Display 15.6 inch diagonal BrightView HD screen tactile backlit by LED (1366 x 768)

  500 GB HDD at 5400 RPM hard drive

  Multimedia drive SuperMulti DVD burner

  Network 10/100BASE-T Ethernet LAN (RJ-45 connector) map

  1 x 1 wireless 802.11b/g/n WLAN connectivity

  HD audio, Audio with stereo speakers

  Keyboard full size Island-style keyboard with numeric keypad

  Pointing device Touchpad supporting gestures multitouch without power button

  Ports external multi format digital card reader for Secure Digital 1 maps

  SuperSpeed USB 3.0

  2 (USB) 2.0 universal serial bus

  1 HDMI

  1 VGA (15-pin)

  1 PORT RJ-45 (LAN)

  1 plug headphone-out/microphone-in combo size 1.11 in. (H) x 14.88 in (L) x 10,20 in. (D) weight 4.96 lb power 45W AC adapter

  3 cell 31WHr 2.8 polymer battery of lithium-ion ID Mech Description Front facing Webcam HP TrueVision integrated high definition with digital microphone

  * After Effects CC (2014) system requirements and Windows language versions *.

  Intel Core 2 Duo or AMD Phenom II processor with 64-bit support

  Microsoft Windows 7 with Service Pack 1, Windows 8 or 8.1 Windows

  4 GB of RAM (8 GB recommended)

  5 GB of available disk space; additional space required during installation (cannot install on removable flash storage devices)

  Additional disk space for the cache drive (10 GB recommended)

  display 1280 x 1080

  System 2.0 - taking supported OpenGL

  QuickTime 7.6.6 software required for QuickTime features

  Optional: Adobe-certifi ed GPU card acceleration graph plotted in 3D rendering engine Department

  Recording and Internet connection are necessary for activation of the software required, validation of subscriptions, online access to services *.

  * I also have a 1 TB external hard drive *.

  Your problem is that the program wants a good video card and a fast hard disk and a lot of memory and have in what precedes. If you have upgraded the RAM to 8 GB memory and installed a disc hard solid state, you could do the program usable but the real bottleneck is going to be the Intel HD graphics, which cannot be upgraded.

  You don't have a slot open for add a 4 GB memory module. It is a simple upgrade relatively inexpensive. See here:

  https://www.YouTube.com/watch?v=L7FvZ-JduRM

  http://www.crucial.com/USA/en/ct51264bf160b

  I'll try this one step at a time. Next would be the solid state drive. It would cost maybe $150. If you need assistance.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.