"camera" always bring up the camera in auto mode higher

Similar Questions

• PXI8433/2: Jumper W1, activate the 2-Wire-Auto mode permanently

  Hi all

  I would like to run the software owner windows PCM001Z on our PXI system. The software to communicate via a port of the PXI8433/2 RS485 card thread-dual with a Toshiba frequency converter.

  Unfortunately, it seems that if the software erases him register scratch the PXI8433 uart, which leads to the deactivation of the two mode of wire.

  My Questions:

  * Is there a way to activate the 2-wire-auto mode of the PXI8833/2 permanetly?

  * What is the use of 5 riders "W1" marked on the map PXI8833/2? These jumpers could be used for the configuration of the PXI8433/2 card?

  Thank you very much in advance,

  Cheerio,

  Volker.

  Hi all

  Meanwhile, I managed to port 1 of our PXI8433/2 card in 2-wire-auto mode without echo constantly with the help of a soldering ;-) iron

  The following steps are necessary:

  1. to disable the echo, I simply connected the receiver enable pin re(4)/Re(2) (3) line RS422 MAX3086 (U7) amplifier with the

  transmitter activate pin TE (4).

  Note: The re(4)/Re(2) PIN must be bgas of CCP.

  2 2-wire-Auto mode permanently by connecting the transmitter to activate the aforementioned RS422 line

  by car on the TxRdy0 pin (21) of the OX16C954 (U11) UART. Please note that the signal of the SOW goes digital

  Insulator ADuM1400 (U1). So PIN 6 of the U1 has to be bgas since the circuit printed and connected to pin 21 of the U11.

  For RS485-2-wire-correct mode, the following windows to port 1 settings must be defined:

  [x] use the FIFO buffers

  Transmission buffer: low (1)-> sovereign placed at the border to the far left

  Transmitter/receiver Mode: 4-wire

• [Camera RAW] Is it possible to adapt the algorithm of auto lighting?

  I find auto to be a decent starting point to adjust exposure and generic lighting, but I find that the algorithm is incorrect:

  1. the algorithm always puts the white on the edge and generates black/white clipping. Auto should never allow that.

  2. the algorithm is more focused on the right exposure settings, rather than evening the entire image to make a curve smooth color.

  3. I think I wish I could say just the algorithm "Okay, its good and all, but I want each time for the algorithm to be a little less exposed.". I don't like the lighter images, unless I go to this effect. I love the deeper images, and I find that too much light makes the entire image... flat.

  Is it possible that I can change the 'Auto' button to choose a different algorithm, for example, less light or more light?

  Is it possible that I can change the order of precedence of the auto, focus on the configuration of other parameters before you adjust the exposure, or focus on the lighting curve smoothing, rather than put the lighting in the same area?

  I wish there was a way to point to something and say the program, "this point, this is where you need face lighting the most for auto.» If this area is bad, its automatic failure on the curve of the car. »

  No, it is hard-coded in. However, you can apply the car in a different way. You can shift/click on the individual settings to only set Auto for these adjustments you want to make.

• Since the installation of Windows 10 why I looking for recently downloaded messages in the Inbox? Before, they came always located at the top.

  I don't know if it's really a problem with Windows 10, but I never experienced it until after the recent upgrade of my operating system. Before the upgrade, new e-mail messages were always displayed at the top of the Inbox window, and I didn't have to scroll down to find them. Now, the newly downloaded messages no longer appear at the top, and I have to search for them after downloading.

  Click the heading labeled DATE sort by date. Click on DATE again to reverse the sort.

• Lenovo Y410P was stuck in the loop of auto repair, but it came out

  So my Lenovo Y410P was stuck in the loop of auto repair, I tried holding the power button and F11 and on as the third seeks the laptop turned on as usual. But now I'm afraid to turn my phone off, how do I know if the problem is solved? And if it is not, what should I do?

  TookMeAWhile wrote:

  So my Lenovo Y410P was stuck in the loop of auto repair, I tried holding the power button and F11 and on as the third seeks the laptop turned on as usual. But now I'm afraid to turn my phone off, how do I know if the problem is solved? And if it is not, what should I do?

  Check the system for corruption files by running sfc/scannow in an elevated command prompt.

• What restoration brings back old bags in the device? I was always told that icloud restoration brings all the bugs back, yet care apple lately told me than vice versa. I'm lost in a cleaner for restoration of backup: icloud or itune?

  What restoration brings back old bags in the device? I was always told that icloud restoration brings all the bugs back, yet care apple lately told me than vice versa. I'm lost in a cleaner for restoration of backup: icloud or itune?

  I've never heard a backup report bugs, however if you are interested in, you can always restore the device as good as new.

• All of a sudden, the Yahoo homepage is different with Firefox. How to bring back the old home page? I prefer the one that is always displayed on Internet Explorer

  All of a sudden, the Yahoo homepage is different with Firefox. How to bring back the old home page? I prefer the one that is always displayed on Internet Explorer. I deleted Firefox and re-installed but the rest of the problem. Help, please.

  Well, it's a problem in your Firefox. To me this https://www.yahoo.com/ page looks like the screenshot of IE.

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Click the menu button

     

     , choose historic, then on clear recent history...

  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

• Why when I open my camera Foscam, Activex mode, I have no picture, and I click on manage at the bottom, but ger javascript:adminstrator0. Why

  My FI8910W Foscam, opens after the Panel, with three modes to the choice. Only ActiveX in IE mode, working to allow records to do. Sometimes, back, right after that I bought this new laptop, a free AT & T program with McAfee, is available for AT & T users. But this soft, can be loaded in Internet Explorer, and something wrong with IE, it prevented from happening. I contacted AT & T Tech support, allowed the tech on my machine, and even he couldn't solve it. Then, he opens Firefox I already had and installed a program that makes Firefox actually act like IE, so that the McAfee software, can be downloaded and installed. He worked, using Firefox to replace IE, to download and install, but the spooler to print on my pc, went wrong, and would not work to use my printer. Tech Dell takes control of the pc, found to reinstall a full Windows 7 was necessary, and he did. Now, the works of print spooler, but the new facility, has removed the AT & T Tech software added to Firefox.

  That is a pain, but we need, for some sites, as for the Activex mode, with my camera. I tried pening mode ActiveX in Firefox, and it opens, but not picture. When I click on device management, to go into the settings, I can't. What I get is a little pop ball down to the right, that says "javascript:administrator0". Thinking that perhaps the Javascript has been disabled, I checked in the options and it's not so it is checked, enabled. I'm on my pc as an administrator, so now I'm stuck. Y at - there someone who can explain how to make it work, so I can use my camera in ActiveX mode, so I can actually record tings, if necessary, when I leave? Thanks in advance. Oh, my Win 7, a 64-bit OS, not the 32 if it helps.

  More than likely you have had IE Tab installed in Firefox before re-installing Win7.

  https://addons.Mozilla.org/en-us/Firefox/addon/IE-tab-plus/

• I block junk emails every day, always bring, I mark the email phishing scam day after day, always find them in the same places day after day after day, is it possible to stop really and how?

  I block junk emails every day, always bring, I mark the email phishing scam day after day, always find them in the same places day after day after day, is it possible to stop really and how?

  original title: tired of it

  You have posted in a forum for MSE, antivirus, antimalware application.  You must investigate e-mail options... providers (hotmail, gmail, yahoo, etc) screen several e-mail for spam.  You don't have not yet described here your email client... so there is little that anyone can tell you that generic advice.

• When I press the 'return' or 'up' button, files always bring me to the top of the list.

  When I press the 'return' or 'mounted' in any file button, it always happens show the top of the list of files or folders, not where I was. Let's say I'm looking in a file and got all the way to a file starting with "M" - when I double click on the file, and then click the back button, it brings me to the beginning of the alphabet (aka, at the top of the list of files/folders) and I have to scroll all the way down to where I was. I don't remember all the previous versions of windows, in doing so, but I could be wrong - if it is a new feature, is it possible to turn it off?

  I want to emphasize - I have seen a lot of suggestions dealing with this problem on the internet, but not what I'm looking for. This never happens for me on the internet, ONLY in the files of the computer.

  Thanks in advance for your suggestions!

  Hi CFive,

  This detail of navigation seems to be design / in the XP operating system by default. There is no way to disable or change this feature.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• DNS server error that always brings back us to windows update erros trying to get on the internet

  Vista - hate him. I spent hours on the phone with a brand new computer that Toshiba with Vista 64-bit Edition Internet will stop working with the DNS server unknownerror. Sometimes reboot help but with all Windows update he internet is a luxury. Internet connection is perfect, perfect bc other laptops in the House with no problem, router, no viruses etc., computer - fine tooth - comb nothing.

  Take each OFF download windows update and work until updates again and then started barking at me, something is missing like its updates! Can't very well what update is screwing the connection or networking or a framework-Silverlight is always suspcious to me also.

  My icon for internet splits in two and shows as a #2 without asking confirmation except for a mysterious update. Access: Local and Internet. Symbol of the Internet will be turned off and will not ever look like disconnected until you try to connect.

  That's why people are going to Apple. Windows will not help or is somewhere secret and accept just your visa and mastercard and so what still you? Vista I can't update and no security.

  Toshiba is not very user-friendly, that is toward the back, they discovered Windows was the question. Isn't our problem, said - even if we're stuck with Vista with their product!

  I'd love to hear if someone has SIMILAR problems or if anything that I did not have tried! Thank you very much.

  Signed. Never buy new windows - toshiba on my list too.

  Hi begodsbutterfly,

  Welcome to the forum of answers windows vista.

  We are sorry for the inconvenience that you had to go through. I have some steps you can try to solve this problem.

  Try to check in SafeMode with Networking if the same problem occurs. To start in safe mode with network, restart your computer and press the F8 key for about four to five times. You will see the window options of safe mode with network in rated advanced. Use the arrows on your keyboard to select Safe mode, and then press ENTER.

  Please check if you get the error in safe mode with network.

  You can also try a system restore to the date when the computer was working fine.

  To do a system restore, please follow the steps below:

  1. click on start to reduce this includes this image, type systempropertiesprotection in the Search box and press ENTER.

  Reduce this includes this imaIf that you are prompted for an administrator password or a confirmation, type the password or click on allow.

  2. in the System Properties dialog box, on the System Protection tab, click System Restore.

  3. in the System Restore dialog box, select choose a different restore point, and then click Next

  4. Select the restore point that you want to use, and then click Next.

  5 confirm your restore point and then click Finish System Restore restores the selected Windows Vista configuration and then restarts the computer.

  6 log in the computer. When the restoration of the system of confirmation page appears, click on OK.

  The system restore article is:

  http://support.Microsoft.com/kb/322756

  I hope this information is useful.

  Please let us know if you need further assistance.

  Concerning
  Rehman - Microsoft Support

• HOW TO BRING BACK THE BROWSER MORE OLD?

  REVISED ORIGINAL QUESTION =
  AFTER ALL THE ~ through the MESS you created and YOU in ME SAYING that "in order to have a chance to get the answer to my question ~ to give you ALL THE DETAILS I can ', you REFUSE to accept by saying, ' Please keep the length of your question to 255 characters or less...» » !!! You are ABLE to say that BEFORE I go through all the other MESS? HOW TO BRING BACK THE BROWSER MORE OLD?

  ISSUE INITIAL = I got SEVERAL plugins that WORKED! Then, I 'upgraded' {like you, LAUGHING, claim} to your version of Firefox 4 after promising to you that it is BETTER and, supposedly, an IMPROVEMENT over the old version. After you install the NEW one ~ IT TURNS OUT ALL MY PREVIOUS PLUGINS! Your WISHTHEYWUZ "PROGRAMMERS", very skillfully {and, in fact, HATEFULLY} uh, kinda "forgot" to make the new browser for COMPATIBILITY ASCENDANTE so that it does not DESTROY us, already, had ~ that WORKED before YOU put your hands on it! So, now, * HOW * I get the OLD version back? I think you need to KNOW what you can do with this new 'UPGRADE' which is, in fact, a LIE! UPGRADES don't take you BACKWARDS ~ make things WORSE ~ real upgrades make things BETTER! DUH-H-H!

  ORIGINAL DETAILS =
  I, recently bought, a new HP 4500 printer and it came with an extension to capture video/plugin. Attempt to use, the program informed me that I had to use, either, an IC or a Firefox browser mentioning the version1.5 {I think it was} or later. The Firefox browser I was using was 3.something; then, everything was going along FINE. When I installed the video capture program, she added the plugin for the browser ~ PERFECTLY! I had too MUCH other plugins that worked and I used somewhat regularly! NO MORE! YOU and your TOTALLY INEPTE, WISHTHEYWUZ 'PROGRAMMERS' STOLE half of my COMPUTER! I can't, is more, USE ALL OF THOSE PLUGINS, simply because you "forgot" {say} to INCLUDE in your new browser version 4. WHAT WAS WRONG WITH THEM? WHY DON'T * YOU * WANT ME TO BE ABLE TO USE THEM, MORE?

  Apparently, YOU think that the computer world revolves around YOU, and YOU are its AXIS! You feel that YOU have NO RESPONSIBILITY to make YOUR programs in no way compatible with what is already available ~ according to the "advice", I noticed on one of YOUR pages WHILE REACHING THIS ONE, you said that everyone must adapt to YOUR claimed "improvements" that are just DESTROY!

  All I want is for YOU to either MAKE YOUR VERSION 4 COMPATIBLE; or advise me on HOW to get the EARLIER back version that * IS * compatible. Otherwise, I'll switch to another browser and advise all the others that I have one any influence to do the same for the good of their overall computer enjoyment!

  PLEASE ADVISE!

  I see that you have provided this window} {below a space for, probably, a UNIQUE Extension / Plugin.} Therefore, a PARTIAL LIST follows ~

  ArcSoft video 2.0.0.8 Downloader extension
  Copy into Wordperfect Lightning 1.0
  Google Photos Screensaver 2.0
  HP Smart Web Printing 4.5
  iWinGames Plugin 1.5
  Microsoft.NET Framework Wizard 1.2.1
  2.0.0.11 RAW thumbnail viewer
  Real Player browser Record 1.1.3 Plugin
  TVU Player 2.5.3.1 Web
  Yahoo! Toolbar 2.1.3.20100310105313

  http://support.Mozilla.com/en-us/KB/installing+a+previous+version+of+Firefox

  http://www.Mozilla.com/en-us/Firefox/all-older.html

• I just bought a 6 d. is it possible to use the grid in other than the auto mode?

  I just buy a 6 d.  Is it possible to use the grid in other than the auto mode?  Also, is there a way to use the self-timer in other than the auto mode?

  Thank you very much. I look forward to your comments.

  I have to assume that your camera came with a manual you need to rely on. In my manual for my 7 d Mark 2 the index near the end of the manual lists the applicapable pages for whatever this is relating to the use or other people. Grid is under G, Self Timer is under S and called "self-timer."

  If you use a computer based pdf to see the info it will probably be several pages listed, but you can click on a page number to get to it rather than scroll to it.

• Using PC printer 4 x 6 borderless Cup always part of the original photo printing

  I print 4 x 6 photos without edge of PC to the printer in maximum resolution.  The overview screen

  always a little cutting edge when in mode without borders, but none when previewing with border.

  Is there a way to work around this problem, or straight up the photo to the size of photo paper?

  JaySenor wrote:

  The last 2 pictures I printed were 2592 x 1952 and 2816 x 2112 pixels.

  I am able to "reduced to adjust" using the HP Photosmart option but that leaves a white

  space on each side of the picture. I am also able to crop manually, but it will also

  leave aside some are photography.  I don't mind shrink the pic so that it fits the

  4 x 6 paper so that none or very little, the photo is at left. Is there a pixel or

  size setting, can I use when shooting images that makes them easier to do?

  Thanks again for your help.

  The impression ratio is 1.5: 1.  The photo above has an aspect ratio of 1.33: 1.  (Divide the number by the smaller number.)  For printing 4 x 6 good size would be 1200 x 1800 pixels of the camera.

• 2600n: printing on Windows 10 always prints to the file rather than to my 2600n

  I bought a new laptop which had 10 (64-bit) Windows installed already.

  When I connect my 2600n printer to the laptop via the USB port and attempt to print anything, the print function recognizes the 2600n is available, but the software behaves as if I chose the option to "Print to file" instead of send data to my printer.

  On the Microsoft Web site, I tried a Windows 10 compatible driver for the 2600n.  I had to download the Microsoft Update catalog that I searched.  The catalogue lists the 2600n, but it does not list Windows 10 like it in support.  The latest version of windows that supports 2600n is Windows 8.1.

  HP has a driver for the 2600n that works on Windows 10 (64 bit)? ... or where can I find?

  I noticed that my 2600n is not the default printer.  Even though I chose the 2600n for the print operation, Windows 10 boiled corn have a bug in the driver and it always sends to the default value.  The default is to print to a pdf file.

  3 times in 3 different ways, I tried to change the default printer to the 2600n and my attempts have been ignored.
  The 3rd time, it looked like it changed the default printer of what I wanted, but when I went to use,.
  It's the same old problem.  Then I left the print operation and came out from the browser where
  I tried printing and did something else.

  I used the NotePad editor later, when I thought I would try to print something new and this time it worked.

  Apparently change the default printer has not taken effect properly and I had to get out of the service where I was doing printing before it would work.

  So the solution is to change the 2600n to be the default printer... and wait a little and do something else.
  out of everything you did before you try again.