Can't see iscsi storage

Similar Questions

• Can not see the storage on BladeCenter S

  Hello

  I have a HS23 blade with an on-board ESXi 5.0 USB stick and I have problems adding storage in the vSphere Client. The BladeCenter chassis has redundant SAS RAID modules. With the help of the IBM Storage Configuration Manager tool I created a pool of storage RAID 5 with a volume on this storage pool and assigned the volume to the blade HS23.

  The previous read, I was expecting the new volume to appear in vSphere client essentially like DAS but I don't see anything. Matter who has ideas that I could have done wrong?

  Bay 6 or 5? Your document Word said earlier that the volume titled "VMstorage" is mapped to "Blade_Bay_5".

  If you are sure that you have mapped the drive correctly and do not at all see it when viewing your storage controllers in VMware, it is best to call VMware and see that if their storage media can help you understand why you don't even see the storage when viewing your controller.

  

• 5.5.1 Director - can not see political storage (or their warehouses of data/clusters) created in vCenter 5.5

  This is a new installation of vcenter 5.5 & 5.5.1 when I linked first the vcenter in Director I see policies of storage, that I had created as well as their data warehouses, but if I can change storage on the vcenter policies I don't see none of them more when trying to add them to the TDC and the option * (any) is no longer present all data stores that were part of them either even if I delete their tags of vcenter and storage policies.  As an experiment I tried to disassemble everything Manager and add the vcenter, I could see once more storage policies, but all other changes make it disappear again.  I tried to update vcenter in accordance with another similar post storage policies, but it does not help.

  Is it perhaps a residual link with the old methods of storage profiles that must be maintained?  I tried to create those via the client of windows as well but could not see them in Director either.  Is it a problem that I don't see storage profiles in the policy storage or web client in the windows client?

  Am I missing something?  At this point, I'm tempted to blow the 5.5.1 Director and install a 5,5 instead device to see if it has an impact.

  Another question: I would be able to see the strategies of empty storage to the Director?  (as in those that are configured and the tag but are not yet associated with data warehouses?)  That would go a long way where I should be shot if I should be able to.

  The process is fairly simple, but requires a brief interruption and access to the DB to clear some tables.  It is very similar to a browser's cache... clear it, and next time, it's a full download of the remote system.

  I'm working on a document for that matter

• Assistant can't see iSCSI SAN software

  Hello

  I test StarWind version 5 (www.starwindsoftware.com) with an ESX v3.5

  I have configured an adapter for iScsi (vmhba40) and specific vswitch (only the VMkernel port) software. There are specific NIC for iSCSI traffic and no rule of firewall between ESX and SAN.

  .

  Using the Wizard "Adding storage", I don't see the "iSCSI SAN software.

  Anyone have problems with this software SAN?

  Thank you for your reply,

  Yossi

  REM: to be sure that the Starwind is set correctly, I tried

  connect through Microsoft Initiator. And it has been directly

  Ok.

  You probably followed the white paper of http://www.starwindsoftware.com/images/content/StarWind_HA_ESX.pdf

  ?

  ---

  iSCSI SAN software

  http://www.starwindsoftware.com

• vSphere Host can't see NetApp storage

  Experts in expensive storage...

  We have recently installed vSphere (ESX 4.0) on a blade server that connects via the Cisco MDS switches to a NetApp 3140.  I believe all zoning is configured from the MDS switches I can FC Ping both the ESX box and the NetApp.  However, the NetApp does see not all CF developers even if they are in response to a Ping FC of the MDS.

  Initiators connected on adapter 0c:

  None connected.

  Initiators connected on adapter 0d:

  None connected.

  Initiators connected to adapter 0:

  None connected.

  Initiators connected on adapter 0b:

  None connected.

  I have connected a call with NetApp, but does anyone have information on what I need to check?

  Thank you

  Damon

  Emulex two ports connect you successfully cloth, but no any NetApp targets found,

  could you please a recheck both ports target NetApp and Emulex ports added to the fc switch even area? Thank you

  usually says it below the successful.

  ~ # cat/proc/scsi/lpfc820/6

  Emulex LightPulse Fiber Channel SCSI driver 8.2.1.30.56vmw

  EMC LPe11002 - E 4 GB 2-port PCIe Fibre Channel Adapter on PCI bus 0000: 08 01 irq 168 port 1 device

  BoardNum: 1

  Firmware version: 2.72A2 (Z3F2.72A2)

  PortName: 10:00:00:00:c9:82:97:e7 Nodename: 20:00:00:00:c9:82:97:e7

  SLI Rev: 3

  NPIV supported: max 100 VPIs VPIs used 0

  SRIP max 512 ISPR used 6

  VPORT list:

  Link Up - ready:

  PortID 0 x 10500

  Fabric

  Current speed 4G

  Physical port discovered nodes: count 2

  T00 FACT State 06 WWPN 010000 WWNN 50:06:01:60:c1:e0:d2:22 50:06:01:61:41:e0:d2:22<---target>

  T01 FACT State 06 WWPN 010400 WWNN 50:06:01:60:c1:e0:d2:22 50:06:01:69:41:e0:d2:22<---target>

  ~ #

  Binoche, VMware VCP, Cisco CCNA

• How can I see how much storage I have and use?

  looking at my creative cloud library-all files - how can I see how much I have storage space, and how much I use to decide if I need more?

  You can check the desktop creative cloud app store as shown in the screenshot above. You can also check in the site settings page for the active CC to https://assets.adobe.com/activity/settings

• I get an error message of complete storage - please backup and remove your something online (can not see the full error message) when converting PDF reader to point rower inacrobat DC. Help, please

  I get an error message of complete storage - please backup and remove your something online (can not see the full error message) when converting PDF reader to point rower inacrobat DC. Help, please

  Hi debg25514049,

  You will not be able to export your PDF to PPT using the service Adobe export in PDF format.

  You'll need subscription to pack Adobe PDF or the Acrobat application to convert PDF to PPT.

  Kind regards
  Nicos

• iSCSI storage presented to the hosts managed by different vCenter Server - questions?

  I currently have three hosts (esxi 5.0) that are managed by vcenter server 5.5 U2. The hosts are attached to iSCSI LUNS (data warehouses) 10.

  I'm migrating to esxi 6.0 U2. For this, there are three new hosts have esxi 6.0 installed and managed by vcenter server 6.0 U2 U2.

  The plan is to detach/remove 5.0 5.5 U2 vcenter esxi hosts. Then import it into vcenter 6.0 U2 (a new cluster will be created). Once imported, uninstall the 5.5 vcenter u2. Then turn off the resident VMs imported esxi 5 hosts and move them to 6.0 esxi hosts.

  My query is regarding regarding storage.

  At present, three new guests see all storage the old 5.0 esxi hosts to see (guests are not in the cluster. "I'm still trying to put things up). That's because the new hosts were deposited to the same group on the side iSCSI initiator storage. Now things, data warehouses are visible by the hosts with esxi 5.0 (managed by vcenter 5.5 u2) and also the esxi hosts 6.0 (managed by vcenter 6.0 u2). The only VMs residing in esxi environment 6 is vcenter 6.0 u2 and update manager 6.0 u2. These are in a data store that is not any other virtual machines.

  That's no problem during the migration? I have not created a cluster for the esxi 6.0 hosts yet and plan to do after obtaining your entries.

  Thank you!

  No problem whatsoever, regardless whether if you do or that you add no vSphere 6 hosts in a HA cluster.

  If you temporarily enable EVC on the vSphere hosts 6, once all hosts are connected to the same vCenter you can VMotion all VMs to new hosts even without any stop. Clear CVS once the migration is complete.

• Access to VMFS existing via iSCSI storage

  Hi all

  In a test environment, I'm trying to access a VMFS existing via iSCSI data store.

  In the storage adapters, I clicked on Rescan. The SCSI target is displayed correctly. However, it is not in the storage, even after clicking on refresh.

  If I click on add storage and select disk/LUN, I can see the storage device, clicking on watch then the primary Partition as VMFS. Of course if I click Next again this reformatted it as a new data store, something I don't want to do.

  How can I get this existing VMFS volume is displayed in the storage?

  TYIA,

  Eric

  www.mymanagedbackup.com

  Have you tried to define enableresignature on 1 in the advanced settings (see attached) and then a new analysis.

• Problem when adding 2nd host in Iscsi storage shared

  Hello people.

  I'll try to explain exactly my problem even if it is a little difficult liitle!

  First of all, we are talking about a test environment that is installed in my house just for learning purposes.

  I am facing a strange my iscsi storage behavior when trying to join a second host to storage vmotion purposes. I was using an Esx host (3.5) for a while and I had no problem with the iscsi storage (I use an old pc with freenas on it). I must say that I got lucky, also, local sata controllers have been recognized so I could test the Storage Vmotion between two storages (Commons and iscsi) with success in this host.

  To continue to learn, I decided to also buy another pc to test Ha cluster, Vmotion, DRS. Unfortunately, I couldn't find the same material and who as well as sata controllers do not to be recognized, so I used a disk ata for OS and my intention was to use for the volume vmfs3 iscsi storage.

  In the first host esx I used, you can see 3 storage adapters: vmhba32 vmhba33& gt; Controllers local sata,34vmhba& gt; initiator iscsi software

  In the second esx host, you can see only the vmhba32- & gt; the iSCSI Software initiator.

  The first time everything worked ok, which means that I have attached iscsi storage in host the2nd by rescaning the vmhba and I was able to browse the datstore and see the contents of it, but it lasted only 10 minutes. Then suddenly I lost the connection to common storage to both hosts, I could see in the section maps of storage, but when I pressed update in the storage section, nothing happened and even when I tried to add it using the add storage I received the message usual "cannot read the partition table information. After being a little more careful I noticed that in the section storage cards, I could see the same vmhba34 in the two hosts with the same alias to the host of the first, and here's the strangest part, the situation I described above has been changing from time to time, which means that a few times I have seen the vmhba32 in both hosts and after some time vmhba34 in both hosts! (crazy)

  I took the big decision after playing with the partition table, without effect to use the ' vmkfstool - C vmfs3 s ' _free "_ / vmfs/devices/disks/vmhba32: 0:0:1" command

  in the second host, of course, I lost all data, but now with a simple refresh in this host, I was able to see the storage.

  Unfortunately, I still couldn't ' 1 host storage access and I published the same command "vmkfstool - C vmfs3 s"free"" / vmfs/devices/disks/vmhba34: 0:0:1 ""

  with only the change you see in bold. Accordingly, it was to see the storage after a refresh with free (1) name.

  Now he is currently working for 2 days with this way not recommended and what I would be really grateful if could help me clarify what exactly is happening.

  My main problem is that I am in front of a very unstable environment that might as well have the same unexpected problem in the future and I can't reformat always storage and loss of all virtual machines

  I tried to describe the best I could to this strange situation!

  Thank you for your time and any help or advice would be most welcome!

  I was looking for a similar solution. Seems to be the only iSCSI host is possible on freeNas. See here: http://apps.sourceforge.net/phpbb/freenas/viewtopic.php?f=53&t=403&sid=f4881e6e25e752e6ee8c6b0eae5887d3

  The only solution for learning seems to be to install the server ESX or ESXi in a virtual machine and then use iSCSI. Vm Instructions to complete the installation here (you must all PDFs 6) http://knowledge.xtravirt.com/white-papers/esx-3x.html or you can replace the opnefiler by the SUN's VM iSCSI. http://www.sun.com/storage/disk_systems/unified_storage/resources.jsp , you must use the vmware converter to convert the SUN's virtual to be used in ESX machine found this in a forum... but can not find more URL. I have not tried myself but, looking for just because you want to get a similar setup.

  Wolfgang

• How to remove the iscsi storage

  Hello

  In the test LAB, I have 2 ESX 3.5 (ESX-1 and ESX-2) attached to the same iSCSI storage called OPENFILER (they have all both local storage).

  1. I want to remove the OPENFILER ESX - 2 storage. Then, right-click on the storage and click on delete. It is said: the resource is in use.

  I tried to put the machine in maintenance mode. Did not help... I have to take it apart this machine?

  What is the right way to do it?

  2. I installed two virtual machines on my storage OPENFILER ESX-1.

  As I mentioned earlier the same storage connected to the ESX-2. When you browse OPENFILER I can see the machines on this (installed on the ESX - 1)

  How do these machine under ESX - 2 inventory. Must I do VMotion or Migration. Sorry came not at that point yet.

  So, before the question, I would like to know the answer to the question two.

  Thank you

  Michael.

  1. I want to remove the OPENFILER ESX - 2 storage. Then, right-click on the storage and click on delete. It is said: the resource is in use.

  I tried to put the machine in maintenance mode. Did not help... I have to take it apart this machine?

  What is the right way to do it?

  Both an ESX 2 can see unit number logic used by the data store that it will be displayed in the list storage ESX-2 - the only way to remove it is that you will have to hide the LUN the openfiler or ESX - 2

  2. I installed two virtual machines on my storage OPENFILER ESX-1.

  As I mentioned earlier the same storage connected to the ESX-2. When you browse OPENFILER I can see the machines on this (installed on the ESX - 1)

  How do these machine under ESX - 2 inventory. Must I do VMotion or Migration. Sorry came not at that point yet.

  The question is you manage these two hosts with Virtual Center - if so you will not be able to have existing virtual machines on two hosts at the same time - in which case you will need to migrate virtual machines from one server ESX to another - with them off a Migration cold or with them under tension - a hot Migration also called VMotion that will require a SAN or a NAS/NFS - shared storage if you are don't not to help Virtual Center, you can save virtual machines using the browser to store data but the virtual machine can only be run on an ESX Server, both-

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• How can I see what I have stored in iCloud?

  How can I see what I have saved in my different devices iCloud?

  Here's how you can visualize what you have stored.

  Manage your iCloud - Apple Support storage space

  Hope this helps, good luck to you.

• How can I see what fits on my ipad?

  I can see a bar on my Mac showing that my iPad is almost full. How can I see which fits all storage so I can remove it?

  Settings > storage & use iCloud > storage: storage management

• How can I see my hard disk and what it contains

  my macbook air has been pop notifications indicating that the startup disk is almost full, which ive just ignored.

  now it says that my hard drive is full and that it cannot receive messages more.

  How can I see which takes all the space

  One way is to click the Apple logo in the upper left corner, and then click this Mac > storage (on the top row).

• How can I increase the storage on my iphone 6?

  My i-phone comes with a notification that there is not a lot left on my phone storage.  I don't want to delete all of my apps.  How can I increase the storage capacity?

  Maybe take a look to see how much of your storage space is taken up with music and pictures and stuff like that.  You can move a lot of this to iCloud.