Can the Airport Extreme connect wireless to my wifi network?

Similar Questions

• All my Airport extended expresses abandoned their Wi - Fi connection to my base station can the airport extreme.  In other words, the light goes from green to yellow flashing and I can't reconnect.  All ideas

  All my express airport extended (one for music, one for the printer and one to extend range) lost their connection at the same time.  In other words, they all went from green to yellow flashing.  I was not able to reconnect.  Any ideas on how to solve this problem?

  Your first step is always power off the entire network... what... and then restart in good order.

  Modem... Wait 2 min

  Main router... Wait 2 min

  Extenders... Wait 2 minutes.

  Printer and other clients... wait that see everything toward the top.

  If this fails, then you need to find how the network is down... Connect the modem to the computer by ethernet... didn't you internet... If Yes... then try to the main router... If so, try again the next step... When you find the scene of the breakdown, reset it to factory and redo the configuration.

• The airPort Extreme has green light, but nothing can connect to it.

  My 5th generation AirPort Extreme suddenly stopped allowing all devices connect via WiFi or Ethernet. I can't see it in the AirPort Utility, I can not access it via the browser, and I've rebooted several times without success. I'm afraid, it may have just died, but I'll try to revive because while I can buy a new one, I hate the look of the new units. Any suggestions?

  Try powering down of the entire network... all devices... in any order you want

  Wait a minute

  Start the modem and let it run a few minutes

  Start the AirPort Extreme and run a full minute

  Keep a minute out one at a time until the entire network is back of boot devices

  Report on the results

• Impossible to extend the AirPort Extreme wireless network

  I have a wireless network set up with a time Capsule airport 4th generation.  I'm trying to take my old AirPort Extreme wireless 3rd generation. I have double. Kettle has implemented, but I get the status message on the extreme that it cannot extend the network.  I can get a strong signal on my iPhone from the point that I have placed extreme itching so I'm close enough to the time Capsule.

  Could I use a connection by current bearer through my home wiring to the extreme and extend it like that?

  Does anyone have any suggestions?

  Please follow these steps closely and report on your results.

  Power off time Capsule airport.

  Wait 10 to 15 seconds

  Power up Time Capsule airport

  Reset the AirPort Extreme back to default factory

  Set up AirPort Extreme still extend wireless signal of the time Capsule

  Report on the results

• Airport Extreme connected to TIVO: why I can not change Type firewall for IPv4.  Field displays IPv6 and is grayed out so I can't change.

  TIVO requires certain ports to be unblocked.  So I try to add the ports requiring TIVO.  But when you try to add the default Type of firewall IPv6 Port Mapping ports and I can't change the value of the IPv4 Port Mapping because the input field is grayed out and no is not accessible.  With Port IPv6 mapping I enter values in all areas except for the IPv6 address because I do not know what value to enter.  I think the button 'save' ' is not available to hit because the IPv6 address field is empty or not valid.  Note: my router Mode is ' Off (Bridge Mode).  Same questions if my router DHCP Mode.

  I changed my router Mode DHCP and NAT, then on the Type of firewall on the default page add ports, IPv4 Port Mapping and I could add ports but with this setting, I couldn't connect to internet in my Airport Extreme: my status remains orange light flashing.

  I use Comcast and my Airport Extreme is connected to my Comcast router using ethernet.

  I use my Airport Extreme as a router (wired and WIRELESS) and as a backup device.

  My TIVO is connected to my Airport Extreme using ethernet.

  How can I add the Ports requiring TIVO.

  Golden in the networking rule. ....... Never try to configure port mapping when you have two devices on the same network the two acting as a router.

  Unfortunately, this is exactly what you're trying to do.

  You have three options:

  (1) run the Comcast router "as what" and configure the port on the device of Comcast mapping... .the airPort Extreme must be configured in Bridge Mode when you do this.

  (2) lance to the AirPort Extreme router Mode of DHCP and NAT and configure the ports on the airport map... the peripheral Comcast must be configured to operate as a simple modem in Bridge Mode when you do this. 

  
  

  (3) lance to the AirPort Extreme router Mode of DHCP and NAT and configure the ports on the airport map... swap Comcast modem/router you have now for a simple modem (it will have only a single Ethernet port).

  In other words, either the Comcast is defined as the router and AirPort Extreme is in Bridge Mode... or... the AiPort Extreme is configured as a router and Comcast must be configured in Bridge Mode.

  If you choose Option 1, then we can not help you on a matter of Comcast router. In bridged Mode, the AirPort Extreme requires no configuration.

  If you choose Option 2 or Option 3, then we the following port values that the Tivo device needs:

  Public or UDP ports

  Public TCP

  UDP private

  Private TCP

  In addition, you need to find the MAC address for the TIVO.  It is a long code that looks something like this, for example:

  A1: B2: C3: D4: E5: F6

  A link to the Tivo instructions for port mapping would also be very useful.  I have done this with a TIVO in the past, but is for some years.

  If all goes well, an expert of TIVO will post to lend a hand.

• Where can I find the Airport extreme N model number?

  Where can I find the Airport extreme N model number?

  It seems that the 3, 4, 5 are all Ns.

  I wish that my laptop wireless backup. A friend has his 5 AE do this via the usb port that is connected to a powered hub.

  Thanks for any advice.

  ett2 wrote:

  Where can I find the Airport extreme N model number?

  It seems that the 3, 4, 5 are all Ns.

  That's kind of how count you...

  But if your AE running 7.6.4 firmware it is Wireless N...

  A look at the base of the number. It is on the first line of molded rubber or paper label. A1408 is Gen5.

  I wish that my laptop wireless backup. A friend has his 5 AE do this via the usb port that is connected to a powered hub.

  Now for a piece of info you don't want to know.

  http://pondini.org/TM/airport.html

  Apple does not support the time machine is a model AE before last Gen6. A lot of people use it, but it can be unreliable... people have a different experience. Just to note that it is not taken in charge and reliability might be good bad or anywhere between the two... Ask yourself how useful is a backup that is not reliable.

• Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...

  Turn on AirPort Extreme for a few minutes... If it is not already turned on

  Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.

  Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status

  Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme

  To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

  Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".

  When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password

• provider changed vague Qwest and now one device connects to the net.  Seems to not be recognizing the airport extreme.  Patches?

  Decided to change providers.  Network domestic fine fixed by extreme airport which has been consulted by 9 apple devices and windows device.  After the wave was installed yesterday, the only device able to connect is the cell that was active at the time of installation.  Is this a problem with my airport extreme or vague does not not with mac?  All the patches would be appreciated.

  After the wave was installed yesterday, the only device able to connect is the cell that was active at the time of installation.

  Sounds like Installer connected your laptop directly to a modem to put in place the new connection.  If that's what happened, then the modem will recognize your laptop, but it will not recognize the AirPort Extreme, then it will appear as if only your laptop can get a connection.

  The modem and AirPort Extreme should probably be reset and then set it up again. We'll know more soon.

  Can you provide the number of brand and model of the modem that was shipped with your service?

  What operating system uses the laptop?

• Airport utility: green points on the AirPort Extreme &amp; Internet; Mini Mac does not connect to the internet.

  Airport utility shows green points on the AirPort Extreme and the Internet, but my my Mac mini does not connect to the internet. IPhones and 2 portable Windows connect very well, and see all the devices on the home network. The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem. I tried to stop and things start back up as if the installation of the internet for the first time. No joy.

  The airport connects using DHCP in Bridge Mode

  The router address is 192.168.80.1

  Address IPv4 is 192.168.80.2

  DNS server is the same as the router, but grayed out

  Mac Mini IPv4 Address is 192.168.80.3

  IPv6 automatically configures

  Also updated the firmware of the airport; no change.

  ISP guy was friendly but puzzled. He started at the top floor level Tech, so I do not know when I hear back.

  Any ideas to fix?

  Thank you.

  Post edited by: en maschera

  but my my Mac mini does not connect to the internet.

  The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem.

  Hello

  Network preferences may be damaged.

  Open the Finder. In the Finder menu bar, click go > go to folder

  Type or copy paste the following text:

  / Library/Preferences/SystemConfiguration

  Click OK, and then move all files in the SystemConfiguration folder to the trash.

  Restart your Mac. See if that makes a difference.

  Your Mac will generate a new SystemConfiguration folder for you.

  Then open AirPort Utility located in HD > Applications > Utilitiies

  Make sure that both Internet and Extreme are green.

  

• the Airport extreme, giving a slow wifi connection

  Hello

  I've got my download speed of 200 Mbps cable company. I checked a good signal by plugging directly in he back of the Modem (to remove the photo Airport extreme wifi.) ... I have 221Mbps actually...

  However, once I'm going to plug in the Airport Extreme and text my speed on wifi, I get only between 24 Mbps or max after several trials of 54 Mbps on download... I should get just under 200 Mbit/s because of the normal fall through wifi... However, not to the extreme I loss I get...

  Tuesday Apple Support has helped me to perform a reboot of the router and I have been good to get 198Mbps... It is here 2 days later and I'm back down to 24 Mbps...

  I tried to redo the reboot: unplug the unit, hold down the reset button, then while holding down the reset button, add power on and continue now stuck until it flashes yellow... But curiously, after it flashes it goes straight to the green... (never asking me to airport utility to add a password)

  My Wifi speed stink...

  What continues with this device... anyone have recommendations?

  I already proved the cable line and the modem (with the support of motorola)...

  Thank you

  Most likely you have a faulty AirPort Extreme. Please ask Apple to replace this unit for you.

  If you wish to renew a reset, follow the instructions very carefully:

  Turning off AirPort Extreme

  Wait 7 - 8 seconds

  Hold the first reset button... and hold in an additional 7 to 8 seconds while simultaneously you reconnect the power on the AirPort Extreme.

  Release the reset button to zero after the period of detention

  Allow a minute for the AirPort Extreme restart. The light will be Orange fixed for 15-20 seconds about, then turn to flashing orange slowly after about 30 seconds

  A slow amber flashing light... about once per second... confirms that the airport has been reset and you can set it up again.

• How can I reset or fix my router wireless or (lost the ability to connect wirelessly to the internet) access point

  Wireless hub works, other computers are connected

  On a laptop, I lost the ability to connect wirelessly to the internet (message: limited connectivity)

  Recommended by the system solution: reset or repair your access point or wireless router

  How can I do?

  I think that what you aim for is "power cycle".

  To do this, simply unplug the router/access point power adapter. Wait a minute. Then reconnect it.

  Hope this helps

  Post back if necessary

  ___________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• The Airport Extreme WiFi intermittent 2nd generation

  I'm having a weird problem with loss of WiFi on my Apple Airport Extreme.

  My 2nd generation that apple Airport Extreme Base Station began to close its WiFi broad signal several times.  It happens usually after 60 minutes or less works very well.  Power on and the new runs for awhile until it stops again the WiFi.  Green light normally forward either static rest without flickering to indicate data transfer, or it will just dark.  Sometimes it will turn off WiFi and then restart WiFi a few minutes later and appear to be good.  But mostly it just stops and I can, he extinguished/turned on to operate correctly with the WiFi again.

  Airport Extreme is connected by ethernet cable to my modem/router main fiber (which is a different floor home) and it is set to "Bridge" Mode  It worked without any problems and I did no changes to my system.  My ISP did update my modem broadband fiber a few weeks ago to a "Virgin Media Hub 3.0"I understand was made by Compal.»  It seems to work perfectly and I have no problems with speed download or reliability in wireframe.  I was away from home for about a week and was able to access my wireless IP camera remotely via my Airport Extreme with no problems.  The problem started almost immediately on my return, but, as I said, I did no changes to my network.  I have never had this kind of problem before with my Airport Extreme.

  I am running OS X Yosemite on an iMac that is connected by a cable ethernet to the Airport Extreme and seems to work very well even when WiFi is de-energized on the Airport Extreme.  Airport utility reports the airport as current firmware version 7.6.7.

  I used network utility, Fing, and it showed that my Airport Extreme has multiple IP addresses, which seem to conflict with the IP address for my three AppleTV.  I manually changed the IP addresses of the Apple TV to another IP address not conflicting, but Fing always shows that my Airport Extreme has three IP addresses and I still have the problem of WiFi.

  Any other suggestions on a probable cause of this problem or the best way to solve the problem would be much appreciated.

  Thank you!

  The question is the 2nd generation AE is now too old.

  I would say the power supply (external or internal) is dying.

  It service life is approximately 5 years... your must be 8 years old. so the solution is simple... buy a new one... or I'll tell... Newish...

• The airPort Extreme (2007) and Time Machine

  Hi all

  I read the info "how to ask a good question" and apparently you need details. I'll try and be concise but informative with my problem. It has been a long journey to get to where I am, but hopefully, with a little help from this amazing community, I can get to my destination.

  Task

  To produce a backup solution Time Machine for the family spending as little money as possible and using the BRIC and broc, I already have.

  Equipment available

  I have a House with some ethernet cables for most rooms that through switches to allow a variety of, most entertainment devices to communicate. It is:

  1 x NAS/Media (ReadyNAS Duo v2) server,

  2 x TV (Samsung),

  2 x TEU (Beyonwiz),

  2 x Apple TV (a 2 nd generation the other is the latest version)

  2 x DVD players,

  1 x iMac.

  2 x 8-port switches,

  1 x 16 switch ports,

  1 x AirPort Extreme (2007).

  1 x Airport Express (age unknown but older than the extreme)

  1 x Fritz! Box 7490 Modem/Router

  Courses in place

  All the associated TV stuff are connected in 2 rooms through ethernet via switch 2 x 8 ports switch 16 central port and then to the Fritz! modem/router box.

  There are also all the usual WiFi going on with mobile phones, iPads and laptops.

  Remarkably, it seems just to work!

  However, I want to add some backup data on our computers. I tried to do by using the ReadyNAS as it is supposed to support Time Machine, but I can't it to appear as a backup destination. So, I thought, as I have AirPort Extreme, I add it to the network and attach a USB HDD for Time Machine since it is supposed to be easy. However, I've been home for hours and cannot make the HARD disk appear in system preferences/Time Machine.

  I plugged the Airport Extreme in one of the switches 8 port said to create a wireless network with the same details as the Fritz! The box according to another article of the support (Airport Extreme wired AND expand network - need of entry). Airport utility shows me Wi-wired connections and seems to work.

  I look at the AirPort Extreme disks tab and can see the attached USB drive here. However, it does not appear as a choice of drives available for backup in Time Machine preferences. I tried 2 different discs with the same result.

  The Question (finally)

  How can I get Time Machine preferences to show the USB disk attached to AirPort Extreme as a valid choice for backups? If anyone can give me a little help in the right direction, I would be very grateful.

  Thank you for reading this,

  Grant

  Unfortunately, the key here is that the version of AirPort Extreme you have does not officially support Time Machine backups on a drive to the USB port of the device.

  The only version of the AirPort Extreme, which will officially support Time Machine backups on a drive in the USB port on the airport is the 802.11ac current version that looks like a "tower". Older versions of 'flat and square' of the AirPort Extreme don't support Time machine with a USB drive attached.

  To check, please see "Time Machine in charge of USB drives" in this Apple support document... AirPort base stations: discs on USB - Support Apple

  Support for time Machine to USB drives

  OS X Time Machine supports compatible USB drives encrypted, related to the time Capsule (802.11n and 802.11ac) AirPort and AirPort Extreme (802.11ac).

  Given that the average life of most wireless routers lasts about 5 years, and your AirPort Extreme seems to be about 9, your AirPort Extreme did very well for you... much better than the average. It might be time to start thinking about a replacement who will be responsible for backups Time Machine... either a time Capsule (i.e. an AirPort Extreme with a built-in hard drive) or another AirPort Extreme.

• Why is my slower than wifi ethernet download speed when using the airport extreme?

  Hi all

  This is my first post here, so please bear with me. I currently own stunted 2011 Macbook Pro 13 inch and an extreme A1521 from the airport. My ISP has promised 50Mbps downloading and sending 10 Mbps. When I connect my MPro via ethernet/wi-fi to my modem I get as promised. When I connect my MPro via wi - fi to the extreme I get 48Mbps download download 9Mbps and it's ok. However, when I connect my MPro via ethernet to extreme I get 8-9Mbps download and 9Mbps. Anyone know how to fix this?

  If you check the 'fine print', your ISP has promised "up to" 50 Mbit/s and 'up to' 10Mbps.  The ISP might provide more than that during periods of slow activity, like the days of the week during the day, but much less during evenings when there are many more users on the Internet.

  When I connect my MPro via ethernet/wi-fi to my modem I get as promised

  I assume that you meant to check the Ethernet connection, you disable WiFi on Mac when you do this. And unplug the Ethernet cable when you check the speed of the WiFi, correct?

  If so, this tells you that the Ethernet port to both the modem and the Mac work properly, and WiFi work correctly as well.

  When I connect my MPro via wi - fi to the extreme I get 48Mbps download download 9Mbps and it's ok.

  If this tells you that the Ethernet connection between the modem and the AirPort Extreme works correctly, and wireless works fine on the AirPort Extreme.

  However, when I connect my MPro via ethernet to extreme I get 8-9Mbps download and 9Mbps.

  Well, you know that the Ethernet connection between the modem and AirPort Extreme works because you can register 48 Mbps Wireless.

  Thus, the possibilities are narrowed to two elements at this stage:

  (1) the Ethernet cable is defective or making intermittent contact. Try another Ethernet cable, to ensure.

  (2) If you have turned off AirPort Extreme and rebooted several times, and you know that the cable between the Mac and AirPort Extreme works properly, then you have reduced the question down to the Ethernet on the AirPort Extreme, which is probably defective switch.

  If you have not already done so, try other ports Ethernet on the AirPort Extreme.

  As a last resort, perform a reset material on AirPort Extreme and put up again. To perform the Hard Reset... power on AirPort Extreme for a few minutes, then hold it pushed in the reset button on the back of the unit (near the AC power plug) for 7-8 seconds and release. Allow a minute for the AirPort Extreme restart orange light flashing slow.

  I once went through two consecutive airport extremes with the same question about 8 months ago, so it can happen.

  If you're still having problems, then it is time to take the AirPort Extreme of Apple Store... If you have one near you... or contact the Apple Support directly by clicking on 'Contact the Support' in the upper right area of this web page.

  Good luck!

• Loading slow web page and with Airport Extreme connection speeds

  About 5 days ago, I noticed a significant slow down the loading of web pages. In some cases, I see a blank white screen for up to a minute before the page is loaded. In others, the page never loads at all. And sometimes they load very quickly as expected. This happens with my iMac that is connected to a router via ethernet, as well as my Macbook Air connected via Wifi to Airport Extreme.

  I have a high-speed internet connection by cable Comcast/Xfinity: Blast 250Mbps.

  I tried to connect my iMac directly on the model of cable (Arris Surfboard SB6183), and there is no problem. Download speed was 30Mbps 300Mbps and upload.

  Then, I plugged my Airport Extreme router again and connected the iMac to the router via Ethernet. Download speed dropped to 100 Mbps!

  This suggests that the problem may be with the Airport Express. It is not a wireless problem, because as you can see the download speed went from 300Mbp/s connected directly to the model 100 Mbps when connected to the Airport Extreme.

  How do I troubleshoot/fix this?

  One last thing: I did a speed test with my Macbook Air that is connected via Wifi and the Airport Extreme router. Download speed dropped to 35 MB/s.

  Direct connection to the modem is so very fast, suggesting the internet connection Comcast isn't the issue. Speed falls even with ethernet to the Airport Extreme router connection, then decreases even more with the Wifi connection.