Can wireless and wired network connections to co-exist on the same pc?

Similar Questions

• My Windows 7 computer is no more can detect the wired network, but all my other wireless and wireline devices connect very well. Replace the network card and no change.

  Hello!  This morning my Windows 7 (the motherboard Acer) desktop ceased to recognize the wired connection to its network card.  In other words, it shows kind of connection, but notes "no Internet access.  It connects to a surfboard by Motorola through one Ooma hub, although I encounter the same problem when I connect to the desktop directly to the surfboard.  All other devices Wi-wired and that connect to the surfboard are functioning properly.

  Thinking that the Realtek NIC on the motherboard Asus was the problem, I installed a new Trendnet network interface card in the PCI slot.  I disabled the network card to the motherboard via the BIOS settings.  No change.  Always 'no Internet access.

  Time Warner Cable test the modem from their office and said it was working properly.  I also connected a laptop directly to the surf board using the same cable, and he was able to connect to the internet.

  Can someone help me understand what the problem is?  Thank you!

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• Wireless and wired network unavailable

  I tried to install XP SP3 on my X 60 laptop. To restart, I couldn't use any network. The LEDs show the wireless as the work, but when I try to use the lenovo or wireless to power to the radio, she continues to declare that 'off '. Also, I can not connect via the wired ethernet port.

  No network adapter appears in my network connections. The devices will appear as normally works in Device Manager and I can update or restore the drivers for them, but I can't uninstall. I can boot to safe mode, but a start in SafeMode with network causes the system to hang during the "checking the status of the integrated security chip.

  Uninstalling SP3 update made no difference.

  Someone can offer more to try, running a new installation of XP? I feel there is just a corrupted somewhere file.

  Thank you

  TD

  Problem solved! It seems that my registry has become corrupted in a way that was also known when SP1 came out:

  http://support.Microsoft.com/kb/329441/en-us

  Removal of two key and restart seem to have cured the problems.

  Toby

• Wireless and wired Internection connection problems

  Hello community,

  My first question concerns my wireless laptop connection (or lack of it). I rebooted my router (because I forgot my password), who restored the device to factory default settings.  When I've reconfigured the router, I was unable to connect to the Internet via a wireless connection. When I troubleshoot with Windows 7, it says that I need to connect an Ethernet cable from the router to the laptop.  However, it was not necessary when the connection to the local area network (LAN) via a public network worked without error.  In addition, when I check my wireless network connection, it shows that the signal strength is excellent and a connection is attempted, but without success.  When I open the network and sharing Center, there is no LAN.  Is it possible that something is blocking access to the LAN? It wasn't a problem, before I changed the router username and password the default user and password. Something is flooded with this situation.

  A second problem occurred when I tried to connect my desktop computer directly to the external modem from my ISP in which I work around the router. There is no Internet connection when this happened.  Before configuring the router via wireless connectivity, the direct connection between the external model of my ISP and my office worked without error. Your thoughts on these two issues are very popular.

  Thank you in advance.

  We're going to do in the first place the wireless and see if we can make it work.

  Go to the router configuration page (it can be www.routerlogin.com or an IP address, depending on your brand.) See your documentation for him.). Under "wireless" parameters must be a place to enter the password you will need to know to access the router. If it is always the default value (which will be probably if reset you factory default), then change to something unique.

  Open the network and sharing Center and click on 'Manage wireless networks' in the left column. Right click on your wireless connection and on the Security tab, select the settings of your router is to (WPA, WPA-2, etc.) and the type of encryption. Then enter the password that you put in the router in the box "network security key. On the connection tab, uncheck "automatically connect...". "for the time being. OK, and then restart. Check if your wireless network is working now.

  To connect to the modem, you may need to recover from the IP. Open a command window, type ipconfig/release and press ENTER. When that finished, type ipconfig / renew and press ENTER. Now you should be able to connect directly through the modem.

  Thing, that I forgot to mention, while you are in the configuration of your router, make sure that "Enable SSID Broadcast" (or a similar expression) is checked.

  SC Tom

• 802. 1 x wireless and wired network

  Hello

  I have to configure a Wi - Fi network and 802.1 x and I don't know what components I need. ACS or NAC appliance?

  Hello

  802. 1 x is an authentication mechanism to devices at the port (L2) level.

  Can be wired or wireless.

  Here's what you'll need:

  A client (Windows computer, peripheral end-user 802.1 x compatible)

  An authenticator (switch, AP)

  An authentication server (Radius)

  The intention is to authenticate the user as soon as the detection of the activity of L2, for example when a user plug the computer to a port on a switch.

  You can do a quick test with the following components:

  Client (Windows computer)

  Authenticator (Cisco Switch)

  Authentication server (ACS)

  Federico.

• Dell Labtop has NO ability to wireless or wired efective connections last night.

  Ability with or without wire

  My Labtop of Wifes Dell has NO ability to wireless or wired efective connections last night. Can you give me a list of procedure to correct this? Please

  I'm going nutts

  Hello

  1. don't you make changes on the computer before the show?
  2. you receive an error message on the computer?
  3. what browser you use on the computer?

  
  Method 1:
  You can try the steps from the link and check if it can help solve the problem.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  
  Method 2:
  I suggest that you want to run the system restore and check if the steps help:
  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore
  Provide us more information for you to help.

• Windows 7 "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. »

  Get the message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. "I am NOT able to connect to the internet please help. I use Windows 7 OS

  Hi Odile,

  Thanks for posting your question in the Microsoft Community forum.

  It seems that you have a problem with the connection to the Internet and receive the error message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is active and running".

  
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  1. did you of recent changes on the computer before this problem?
  2 do you have wireless or wired Internet connection?
  Method 1:
  We'll first run check network troubleshooting if this can help.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
  Method 2:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1
  Method 3:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  How can I troubleshoot network card?
  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems
  For more information, please see the link.
  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet
  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• These two types of schema cache can co-exist for the same application?

  Can these two types of cache-regimes co-exist for the same application in coherence?
  1. close to support-maped by regime distributed cache
  2-reading-writing-support-card system

  From what you describe, that you're on track.

  I think that you have a number of servers that have a size limit near cache and stored disabled for distributed share. Then you have a number of servers that are responsible for the part of writeback (active storage) distributed.

  You can also take a look at the [best practices for consistency | http://coherence.oracle.com/display/COH35UG/Best+Practices]

• IP address conflict between the networks wireless and wired widows 7

  I help manage 25 computers @ work. We affect all components of its own IP address. When you set up win 7 laptop computers that they do not give me a static ip address at the time the connection to the LAN and wireless. I get a conflict message. I put wireless static (10.141.213.xxx) and the connection to the local network to automatically get an IP address the value on the left. I use tcp/ipv4. It works for now, but these portable must also be able to be wired.

  The typical case here is that they must be hard wired but must also be mobile (wireless) troubleshooting automotive computer applications. I tried using the same address and different addresses. I think too much or not strong enough or? I'm a Newby to this site, I posted this question before, but can't find it. Thanks for all the answers and patience.

  Hello

  The question you posted would be better suited in the TechNet Forum; We recommend that you post your question in the TechNet Forum for assistance:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

• How can I turn off the error 'no internet connection '? I am on wireless and my internet connection is often intermittent.  This popup is really boring.

  How can I turn off the error 'no internet connection '? I am on wireless and my internet connection is often intermittent.  This popup is really boring.

  Thank you

  you have to start the application of office cc, at most, once every 30 days.  and if you have an annual subscription, simply start it once all the 91 days.

  so, in your cc preferences, uncheck "Start on login" and close it.

• WIRELESS and wired LAN do not know each other

  My internet provider installed a new cable modem, without capacity WIFI because I have an airport extreme base WIFI (with cable Express extensions).  Speed and quality are OK, wireless and wired, but there seems to be a wall of China between WIFI and wired (LAN): devices that are connected via a cable to my LAN are not visible from the wireless network and vice versa.  Airport extreme is not 'Bridge' mode ("because not of wireless on the new modem capability".)

  No idea of the reasons for this?  Thank you very much

  Sounds like the configuration of the device. With the airport devices it can operate as a device on the network or another firewall as its own network. I think that it is way jumpered to activate, this will allow you to configure the wireless on the airport, but your current router will do the DNS/DHCP and will be a single network.

  Now that you have configured as two routers on an independent network as there is no bridge.

• Wireless and wired router, DHCP and "visibility".

  Okay, it's a bit complicated, but I'll explain better than I can.

  I have a wired Linksys RV082 router. It works very well but is not wireless.  I have a Cisco/Linksys E2500 wireless router for my wireless devices to use.  the RV082 is the network of 192.168.1.x. The E2500 is the network of 192.168.0.x.  Cable Internet goes to the RV082 Wired, and a line out from there to the wireless router.  This all works fine except for a few disadvantages.

  I have an iPad that connects wireless and some of the apps offer a http:// option, so I can transfer files to this application.  I also have a network printer connected to wired and wireless devices do not.

  I have 2 problems:

  (1) in order to transfer files from my laptop (that I hung on the cable network most of the time), I disconnect the wire, wireless, then I can transfer files.  Œuvres, but it's embarrassing.

  (2) I want a netbook that I have on the wireless connection to print on my printer wired network.

  It seems that the 2 networks do not see each other.  Here are the things I've tried:

  (1) I disabled DHCP on the wireless router.  My thought is that requests for an IP address to the wireless router has sent will be transmitted along my wired router... NOT.  On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the disconnected wire and wireless connection with my laptop, I've still was getting a 192.168.0.x IP address, even if the DHCP service is disabled on the wireless router.

  (2) thinking I would put manually the wireless router on the 192.168.1.x network, instead of saying things to get an Internet connection IP dynamicaly, I manually the IP value is 192.168.1.245.  Serious mistake.  I couldn't connect at all anywhere then.  The only way I could fix it was to hang on to my laptop computer, assign a static IP address to my laptop on the same network as the router, then I was able to get to the configuration page and to put things like he was.

  Another thing... Even when I'm connected only plugged on my laptop and wireless is disabled, I ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go in a browser, I get a "page not found" error

  So, how can I get these two networks to play well and see each other?

  Thank you

  Jesse

  Put the router E2500 'bridge' mode and it will transmit the RV082.

  Assign E2500 DHCP, an IP address for itself of thje RV082, it will just be for access to the web administration E2500. System powered via the E2500 wired or wireless IP addresses will be obtained from the DHCP server on the RV082, and these will all be on the same subnet as designed to be plugged into the side of the RV082 LAN.

  Should allow you to do exactly what you want to do.

  I have a similar setup here works well with an E4200V2 right now.

• HP Officejet Pro 8100 does not print - wired network connection - Mac OS x 10.9

  I have my 8100 Officejet Pro connected to my home network via a wired ethernet connection. I use Mac OS X 10.9. We had ongoing problems with the printer is accessible via the network. Whenever we have set up the connection, it works for a few print jobs, but whenever we close the printer, the next attempt to print always fails.

  I just went through all steps to solve the problem. I went back to square one: reinstalled printer drivers on my MacBook Pro running Mac OS x 10.9; has passed through all stages of wired network connection. and now, every time I send a job to the printer, it fits like the receipt of employment and printing, but the printer itself does not.

  The Billboard on the printer indicates it is connected to the network. Print the Network Setup page confirms it is connected to the cable network. Visit the IP address of the printer via my web browser also confirmed. I am able to print a printer HP Print Utility status report, so I don't know that the computer network and the printer are connected and communicate with each other. However, I can't print from MS Word, PDF files or anywhere else outside of the HP Print utility. Work is revealed in the queue, where it shows the status of each page completely 100%, employment disappears, but does never print it.

  Help, please. This has been a problem since I bought the printer, and now that my warranty has expired, it's my last hope of fixing. I'm at the end of my tether with a device that I spent enough money on to expect to work, and it does not work properly literally since the day where it was purchased. All attempts to implement working temporarily, at best. Thanks in advance and if you need more information, please let me know.

  Hi DBG345

  I understand that you are now able to print from USB, but not on the network.

  There are a few things you can try.

  Connect the printer to the router with the ethernet cable.

  Unplug the USB cable.

  Get the IP address of the printer.

  Click on the Apple.
  Click on System Preferences, click on the print icon and scanning, select the printer, click the sign - to remove the printer. Then click on the + sign, then select the printer from the list, select the printer name first, if it does not try the driver airprint, (airprint is apple pre-installed with functionality of basic pilot) click on the Add button.

  You can try is to add the printer as a Protocol IP to see if it will work. Go to Apple, system, print, and scan preferences, click on + button, then select the icon of intellectual property across the top, type in the IP address of the printer, select direct stream below, then apply.

  Try to print.

  I would like to sign up for updates from the HP driver. When available, you will be informed by e-mail.

  Hope that helps.

• At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  original title: server and virus problem

  Hi SurajMendon,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Please post your question in the TechNet Windows XP Networking forum.

  Networking platform

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• The Apple Magic Keyboard can operate without bluetooth when connected to an iPad with the lightning to the USB camera adapter?

  The Apple Magic Keyboard can operate without bluetooth when connected to an iPad with the lightning to the USB camera adapter?

  I love the Apple Magic Keyboard to be very light (I want it with me everywhere). I also like that I can choose the layout of the keyboard I want (Canadian multilingual), which is not available on any keyboard for any brand, with the exception of Apple iPad (and I did a ton of research). I have problems with the old model of keyboard Apple Wireless because of the Bluetooth connection: I often have trouble connecting. I want a reliable keyboard. I don't like having to plug the keyboard on the iPad, and I think that a wired keyboard can more reliable and safer than a wireless keyboard. And a wired keyboard never had battery problems.

  I read that the Apple Magic Keyboard can work wired with a Mac without bluetooth. And I read that some USB keyboards work with lightning to the USB camera adapter. There are several keyboards with a cable (Belkin or Logitech) lightning, but none with the available Canadian multilingual.

  So, if I buy a magical keyboard Apple and a Flash to the USB adapter of the camera, according to my needs, I'll be satisfied or I'm going to be disappointed?

  A better solution would be to have a male-male cable lightning between the keyboard and the iPad, but I don't find any of these products anywhere.

  Thank you.

  It will not work. And where did you read that the keyboard works wired with a Mac?