Wireless and wired Internection connection problems

Similar Questions

• Can wireless and wired network connections to co-exist on the same pc?

  My new desktop pc of Windows 7 has a Wireless N adapter, but given that the router is located next to I prefer to use a wired connection. When I enabled both, I noticed that the pc was connected wireless, so I disabled the wireless card and connected via wired LAN.

  I was wondering if there is any way to keep active both and put in place for the wired connection is a priority, and the wireless connection is used automatically when there is no wired connection?

  When more than one network connection is available, Windows uses the one with the lowest metric value. By default, it automatically assigns a metric value based on the rated speed of the network connection. For more details, please see an explanation of the routes Internet Protocol Automatic Metric feature .

  To force Windows to use a specific network connection, assign a metric value to each of them, giving the lowest value to the desired connection:

  1. Press the Windows key + R , type ncpa.cpl in the box, and then click OK .
  2. Right click on the desired connection.
  3. Click on Properties > Protocol Version 4 (TCP/IPv4) Internet .
  4. Click on Properties > advanced .
  5. Uncheck Automatic metric .
  6. Enter a number between 1 and 9999 for the Interface metric .

  Boulder computer Maven
  Most Microsoft Valuable Professional

• Dell Labtop has NO ability to wireless or wired efective connections last night.

  Ability with or without wire

  My Labtop of Wifes Dell has NO ability to wireless or wired efective connections last night. Can you give me a list of procedure to correct this? Please

  I'm going nutts

  Hello

  1. don't you make changes on the computer before the show?
  2. you receive an error message on the computer?
  3. what browser you use on the computer?

  
  Method 1:
  You can try the steps from the link and check if it can help solve the problem.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  
  Method 2:
  I suggest that you want to run the system restore and check if the steps help:
  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore
  Provide us more information for you to help.

• WIRELESS and wired LAN do not know each other

  My internet provider installed a new cable modem, without capacity WIFI because I have an airport extreme base WIFI (with cable Express extensions).  Speed and quality are OK, wireless and wired, but there seems to be a wall of China between WIFI and wired (LAN): devices that are connected via a cable to my LAN are not visible from the wireless network and vice versa.  Airport extreme is not 'Bridge' mode ("because not of wireless on the new modem capability".)

  No idea of the reasons for this?  Thank you very much

  Sounds like the configuration of the device. With the airport devices it can operate as a device on the network or another firewall as its own network. I think that it is way jumpered to activate, this will allow you to configure the wireless on the airport, but your current router will do the DNS/DHCP and will be a single network.

  Now that you have configured as two routers on an independent network as there is no bridge.

• How can I turn off the error 'no internet connection '? I am on wireless and my internet connection is often intermittent.  This popup is really boring.

  How can I turn off the error 'no internet connection '? I am on wireless and my internet connection is often intermittent.  This popup is really boring.

  Thank you

  you have to start the application of office cc, at most, once every 30 days.  and if you have an annual subscription, simply start it once all the 91 days.

  so, in your cc preferences, uncheck "Start on login" and close it.

• Problems with HP Photosmart C309g wireless and wired

  Hello

  I fought with my C309g since I bought it a few months before.  It works on and outside, but can not hold a consistent network connection.  I have wired it usually but have tried both wireless.  It is plugged directly into my Netgear router.

  Before it works for a short period of time and the other Offline Online & on its own.  Sometimes it recognizes the other computers on the network to print & analyses.  I have 3 PCs on the network - two cables & a wireless.  It will recognize the three rarely, two of them sometimes, one of them sometimes (usually the laptop wireless) and none of these most of the time.

  There each time than in quite awhile for the first month and now it does not appear at all on the network - wired or wireless.  I can't print and more.  The documents simply to sit in Quebec for a while and then produce an error.

  Any help appreciated.  This printer is a wholemeal bread.

  Thank you

  Gringeiro

  Hi Gringeiro,

  You use the wireless WEP or WPA security on your router?  I would recommend WPA2 with AES, well, if you want to connect wireless.  It will also, if you set a static IP address on the printer.  You can do this by typing the IP address of the printer in the address bar of your browser.  Select the network tab, and then look for IPV4 under the section of wired or wireless, depending on how you have connected it.  There should be an option to "suggest manual IP".  If this isn't the case, type IPCONFIG from the command prompt (start/run cmd) to get your addresses in the subnet and the gateway.

• My Windows 7 computer is no more can detect the wired network, but all my other wireless and wireline devices connect very well. Replace the network card and no change.

  Hello!  This morning my Windows 7 (the motherboard Acer) desktop ceased to recognize the wired connection to its network card.  In other words, it shows kind of connection, but notes "no Internet access.  It connects to a surfboard by Motorola through one Ooma hub, although I encounter the same problem when I connect to the desktop directly to the surfboard.  All other devices Wi-wired and that connect to the surfboard are functioning properly.

  Thinking that the Realtek NIC on the motherboard Asus was the problem, I installed a new Trendnet network interface card in the PCI slot.  I disabled the network card to the motherboard via the BIOS settings.  No change.  Always 'no Internet access.

  Time Warner Cable test the modem from their office and said it was working properly.  I also connected a laptop directly to the surf board using the same cable, and he was able to connect to the internet.

  Can someone help me understand what the problem is?  Thank you!

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• WAG-120N and static ip - wireless and wired clients cannot connect to the internet

  Greetings,

  I use the N WAG-120 AP and switch for 3 computers laptops and 2 Office. Our Department is assigned only a what IP static of our server, as well as a pc can connect to the server and the internet. I use the first lan port of the 120N Wag as a WAN port and I attribute the static IP address, and the subnet, default gateway, and DNS addresses. Connected clients receive an ip address from the DHCP (192.168.1.10x) router, but cannot connect to the internet. How can I configure my router to allow clients to connect?

  Thank you in advance!

  The default LAN IP of the WAG subnet is 192.168.1.0/255.255.255.0 belongs to 192.168.0.0/255.255.0.0. This means that 192.168.1.0 IP addresses exist side WAN and LAN of the WAG. What makes this configuration completely cannot be routed.

  Change the address LAN IP of the WAG to an IP outside the corporate network, for example using IP addresses private 172.16/12, for example to set the address LAN IP 172.16.1.1 with 255.255.255.0 subnet mask.

  The alternative would be to use the WAG as a point of easy access only, and not as a router. However, due to the 255.255.0.0 subnet in your network company you will not be able to access the web interface except from an IP address corresponding to the LAN IP address subnet of the WAG. Of course, this does not affect the wireless or wireline customers connected to the WAG...

• Wireless and wired router, DHCP and "visibility".

  Okay, it's a bit complicated, but I'll explain better than I can.

  I have a wired Linksys RV082 router. It works very well but is not wireless.  I have a Cisco/Linksys E2500 wireless router for my wireless devices to use.  the RV082 is the network of 192.168.1.x. The E2500 is the network of 192.168.0.x.  Cable Internet goes to the RV082 Wired, and a line out from there to the wireless router.  This all works fine except for a few disadvantages.

  I have an iPad that connects wireless and some of the apps offer a http:// option, so I can transfer files to this application.  I also have a network printer connected to wired and wireless devices do not.

  I have 2 problems:

  (1) in order to transfer files from my laptop (that I hung on the cable network most of the time), I disconnect the wire, wireless, then I can transfer files.  Œuvres, but it's embarrassing.

  (2) I want a netbook that I have on the wireless connection to print on my printer wired network.

  It seems that the 2 networks do not see each other.  Here are the things I've tried:

  (1) I disabled DHCP on the wireless router.  My thought is that requests for an IP address to the wireless router has sent will be transmitted along my wired router... NOT.  On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the disconnected wire and wireless connection with my laptop, I've still was getting a 192.168.0.x IP address, even if the DHCP service is disabled on the wireless router.

  (2) thinking I would put manually the wireless router on the 192.168.1.x network, instead of saying things to get an Internet connection IP dynamicaly, I manually the IP value is 192.168.1.245.  Serious mistake.  I couldn't connect at all anywhere then.  The only way I could fix it was to hang on to my laptop computer, assign a static IP address to my laptop on the same network as the router, then I was able to get to the configuration page and to put things like he was.

  Another thing... Even when I'm connected only plugged on my laptop and wireless is disabled, I ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go in a browser, I get a "page not found" error

  So, how can I get these two networks to play well and see each other?

  Thank you

  Jesse

  Put the router E2500 'bridge' mode and it will transmit the RV082.

  Assign E2500 DHCP, an IP address for itself of thje RV082, it will just be for access to the web administration E2500. System powered via the E2500 wired or wireless IP addresses will be obtained from the DHCP server on the RV082, and these will all be on the same subnet as designed to be plugged into the side of the RV082 LAN.

  Should allow you to do exactly what you want to do.

  I have a similar setup here works well with an E4200V2 right now.

• Wireless and wired through extreme as an Extender

  I have 2 scenarios to connect my laptop:

  1. wireless on my home network, or

  2 cable to the extreme that works as an extension of my network.

  That it would give me the best speed.

  Thank you!

  1. wireless on my network home

  Your best bet if the laptop is located where it can receive a good connection.  An Ethernet connection from the laptop to the airport would be better. And things will depend on whether you have another airport, expansion of the wireless network, because that will reduce the speed on the entire network.

  2 cable to the extreme that works as an extension of my network.

  Kind of a trick question that you cannot have the intention, since there is a big difference whether the extreme 'extends' using wireless... or... If the extreme "extends" by connecting to the main router using an Ethernet cable.

  When you try to "expand" using a wireless connection between two airports, you lose about half of the potential capacity of speed on the entire network. When airports connect together using a wired Ethernet connection, there is no loss of speed.

  So, to answer your question... If the extreme which is the extension of the network is wired to the main router... There will be very little difference in speed with the laptop using a wired connection or by using the wireless... assuming that the laptop will be close to the extreme.  The wired connection would be more reliable, however, if you have the choice... Since Wireless is a mix of science half and half voodoo.

• HP Photosmart D110 - wireless and wired to installation - at the same time

  PLEASE READ CAREFULLY THAT NO MATTER HOW MUCH DETAIL I SAY QUESTIONS. IF ALL OF THE OTHER INFO. IS NEDDED IT PLEASE LET ME KNOW.

  Hello community I am undergoing, step by step, how can I set up my printer to a network via Wired and therefore any other device connected to that network can print from it.

  I used to have my printer connected via connected to my main PC, but it soon came the need to print from other places in my house and I remembered that my printer has this great ability, so I wanted to know how, step by step. I tried to put in place by myself, but I couldn't, I myself helped with the HP Solutions and Guides, and somehow, I missed something.

  Details:

  OS main PC: Windows XP 32-bit (it has the latest updates)
  Printer: HP Photosmart D110 one
  Router: Time Capsule from Apple

  I uninstalled the printer from my computer, so don't be any errors.

  Here's the deal, I want to connect my printer to my main PC via Wired (cable), once correctly installed, I want to connect this printer on my wireless (Network Time Capsule), so any other device connected to the network can print from it.

  If someone can take the time to tell me how to do, step by step, with links from HP information. etc if necessary.

  I already know how to set up a static for my printer IP address and all the stuff in IT, so don't worry, everything you say me that I understand it, all I need to know is what to do exactly, but the case is when (step by step).

  Thanks in advance.

  Hello, I noticed that you said 'Network via Wired' and then he said "wireless. I will be happy to help you. Just to let you know, you can't be WIRELESS and NETWORK CABLE (Ethernet). You can be wireless and plug the main PC into the USB cable. So, here are the steps to download the drivers and the connection to your PC (USB) PRINCIPAL and others (wireless).

  Connection to MAIN PC wired (USB)
  1. connect the USB cable from the printer directly to the main computer.
  2 download the drivers from the Web site (http://goo.gl/BVOOg), or if you have the CD.

  Note: whenever you download the software and drivers on the site. Be sure to choose the SOFTWARE from FEATURE COMPLETE.
  1. Select software and drivers
  2. type in the name of the product (click Search)
  3. choose the operating system (click Next)
  4. choose Download (scroll to the bottom for the SOFTWARE of FEATURE COMPLETE)
  5. After downloading the software, it will PULL
  6. it will give you an option on how you want that it connected
  7. you choose USB to the PC of the hand

  WIRELESS NETWORK connection
  1. go into your printer settings
  2. Choose Network
  3. Select wireless CONFIGURATION WIZARD
  4. it will search your router (if wireless). Choose your router and configure the printer wireless upward.
  5. go to other computers and follow the steps above to download the drivers.
  6. when it comes to SELECT connection, choose (without wireless/network)

  In this way, you can print from your main PC via USB (wired) and the other wireless computers.

  If your ROUTER is not wireless, and you can only use a wired (Ethernet) network, then you can print only by plugging the cable ETHERNET router to any PC of your choice print from the moment. Also to plug another cable from the router to the printer.

  I hope this helps, if you need more help please ask, thank you.

• How to set up LAN wireless and wired for simultaneous operation

  I use a Lenovo thinkpad running windows XP. I want to set up an independent network so that I can connect my hardware for debugging. At the same time, I want to be able to access the corporate network using the wireless interface.  My autonomous network consists of a Belkin router that is to act as a DHCP server, my laptop connected to a port on the router and my test material connected to a different port on the router. My wireless interface is configured to connect to the corporate network. With wireless interface and the ethernet interface (wired) enabled, when I am doing a config ip, I see that the devices get valid IP address, corresponding to subnets, they connect to IE the ethernet port gets IP address 192.168.x.x 172.x.x.x IP poster wireless interface while. But I am not able to ping or access sites on the internet, I am able to ping the router Belkin on the independent network.

  However, if I go under network connections and disable the ethernet connection to the local network can access the internet and my business network. Similarly, if I disable the wireless connection and that you enable the ethernet connection, so I am able to ping the router only and not my test equipment connected on the same subnet.

  If I configure the (wired) ethernet network interface to use a static IP address in the pool of IP from the router Belkiin (who is also a DHCP server) and set the IP Address of the Belkin router as gateway, I can access all the other devices on this local subnet if and only if the wireless interface is disabled.

  The search for networks order is defined as the wireless and Ethernet.

  In my case, I need two interfaces to be active at the same time, as explained at the beginning. Appreciate any suggestions.

  Thank you.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  Hope this information is useful.

• WRT54G2 v1 - Internet is slow wireless AND WIRED

  OK, so I get my internet to an ethernet cable plugged into the wall (I don't know if its cable or dsl because I live in an apartment). When I connect from the wall to my Macbook internet is fast with Mbit/s to 30. But, when I connect to my router ethernet cable and try to access the internet, wireless or wired through the router it takes 15 seconds to load a Yahoo page or a Facebook page

  Now for the confusing part. When I use the wireless on my PS3 (implemented with automatic adjustment to the subject), it goes fast enough where he can even listen to HD Netflix movies and fast enough not to get lag on Call of Duty or no games. But when I want to look at a web page on my iPod Touch, Blackberry phone, Macbook Pro and 3DS it takes forever to load a. Interestingly enough, I tried to SpeedTest.net on my Macbook and here is my result when connected wireless (always takes forever to load a Web page, and it does not load the hulu or youtube videos).

  Any advice will help!

  Try this http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3733&lid=7610935397b08. Try the first configuration

• Laptop (HP ZV6000) and WRT160N plu connection problems

  I recently got a new HP Touchsmart 600 and set up with a Linksys WRT160Nv2 router. The Touchsmart works fine, no problem, and is so the Dell Latitude D630 I use for work.

  However, for some reason, I can't get on the internet through our other computer, which is an older HP Pavilion ZV6000.

  I implemented the Broadcom Wireless software that came with the computer and it says that it is "connected" to the router wireless... but when I open Internet Explorer, it says 'cannot connect to the Internet'... and immediately goes to work offline.

  I used to have the laptop HP connected to a Linksys WRT54GS wireless router and never had any problems (or, at least, nothing that I couldn't solve).

  Is there some kind of conflict between the WRT160N and the HP Mini PCI Broadcom 802. 11B / G wireless LAN Card?

  You have the static IP address on the HP laptop.

  Do the automatic IP address settings wireless network connection and see if you are able to access the Internet.

• Windows Vista Media Extender and xbox 360 connection problem

  I get the following error message when you try to connect my xbox 360 to my PC to vista through the Windows Media Center extension
  Connection complete

  The Xbox 360 has been disconnected because an application has launched unexpectedly UI. You want to reconnect?

  I followed all the steps of your forums that are supposed to resolve these issues, but he continues to be. What can I do to fix this?

  Hi Snufferum,

  Thanks for posting on answers.com.

  First, disable the program anti-virus or firewall that runs on your computer and check if the problem persists.

  Note: because some anti-virus software will cause conflicts between unexpected applications, please temporarily disable any antivirus, firewall or anti-spam on your computer programs.

  This problem occurs if the floating language bar is enabled on the Windows Vista-based Media Center computer. This configuration closes the connection between the Media Center Extender and the Media Center PC.

  To resolve this problem, change the settings of the Media Center Extender language bar. To do this, follow these steps.

  Step 1: Configuring settings on the Windows Vista - based Media Center computer

  1. Click Start , type intl.cpl in the Start Search box and press ENTER.
  2. On the keyboards and languages tab, click Change keyboards .
  3. On the Language bar tab, click docked in the taskbar under options from the language bar .
  4. Click OK .
  5. On the administration tab, click copy to reserved accounts .

  If you are prompted for an administrator password or for confirmation, type the password, or click continue .

  1. Click on the checkbox by default (new users) user account , and then click OK twice.
  2. Click Start and then click Windows Media Center .
  3. Click tasks , and then click settings .
  4. Click Extender , and then on the Xbox 360.
  5. Click Uninstall , and then close Windows Media Center.

  Step 2: Configuring the settings of the Xbox 360 console

  1. In the System of the Xbox interface section, select computers .
  2. Select Windows Media Center , and then press the A button.
  3. Select Disconnect .
  4. Press the B button repeatedly until you return to the System section.
  5. In the media of the Xbox interface section, select Media Center .
  6. Advance in the instructions on the screen to get the 8-digit setup key.
  7. Note the setup button.

  Step 3: Configuring the settings on the Windows Vista - based Media Center computer

  1. Click Start and then click Windows Media Center .
  2. Click tasks , and then click add extender .
  3. Click Next and enter the 8-digit setup key you obtained media of the Xbox interface section.
  4. Follow the prompts to complete setup of Windows Media Extender.

  When you copy these settings for reserve accounts in the 1st step, you change the settings of language bar for all new users that are created on the Media Center computer. After you add the Windows Media Extender, you can reverse these changes so that all new users will have a floating language bar. To do this, follow these steps on the Windows Vista-based Media Center computer:

  1. Click Start , type intl.cpl in the Start Search box and press ENTER.
  2. On the keyboards and languages tab, click Change keyboards .
  3. On the Language bar tab, click floating on the desktop under the language bar options .
  4. Click OK .
  5. On the administration tab, click copy to reserved accounts .

  If you are prompted for an administrator password or for confirmation, type the password, or click continue .

  1. Click on the checkbox by default (new users) user account , and then click OK twice.

  You can go through the article below:
  http://support.Microsoft.com/kb/934542

  While trying to use your Xbox 360 as a Media Center Extender console, you receive the error message: "Setup error".

  http://support.Microsoft.com/kb/932342

  This article should help you work on problems you encounter while trying to connect to the Xbox 360 and Windows Vista.

  Connect your Xbox 360 to Windows Media Center

  http://www.Microsoft.com/Windows/products/winfamily/mediacenter/Xbox360.mspx

  Kind regards
  Technical support of Microsoft-yama.
  Visit our Microsoft answers feedback Forum and let us know what you think.