Cannot access the synology on nested host iscsi datastore
I installed a Synology ds 414 version - 5-2-5592, with 2 volumes prescribed as 2 iscsi targets, I'm running 2 esxi 6 guests, a physical and a nested, phyiscal host I can access the target immediately without any problem, the host nested when I use the dynamic discovery, I can see the target via the static mapping but LUNS never appear and I can't add them as data stores.
I put the target to allow multiple sessions on the synology, I can ping from the nested host synology vmk. I added the host nested as initiator allowed on the Synology, although I didn't need to do it on the first host as default value is set to read / write and there is no authentication set to synology.
I have attached a few screenshots
Any help would be greatly appreciated.
You have activated on your physical host vSwitch promiscuous mode? See this thread to another: Nested ESXi 5.1 and iSCSI Shared Storage
Tags: VMware
Similar Questions
-
internal hosts cannot access the internet w / L2L configured tunnel
The internal hosts behind the ASA cannot access the internet with a configured tunnel to L2L. The L2L tunnel is mounted and passing traffic correctly. However, the internal host cannot access the internet through the ASA. I think I have my NAT watered somewhere. I can't even a host statically mapped to the internet. It might be because I'm used to having a WAN IP to the external interface which differs by the CIDR block assigned by the ISP. In this case, it's all together, with the ASA outside interface occupying the first available address.
We have been assigned a CIDR range x.x.x.64/28. x.x.x.65 is my front door and my first usable est.68, by the PSI (I guess what they utilisent.66 et.67 for internal use). External interface of the ASA est.68 and I'm trying to get NAT others. I'm Polo all DHCP clients internal and have some static entries as well. Below is the relevant NAT config. Yet once, all traffic passes above the tunnel properly, but not from inside to outside. If more information is needed, please advise.
interface outside
IP address x.x.x.68 255.255.255.240
NAT-control
Global x.x.x.69 - x.x.x.77 2 (outdoor)
Global 1 x.x.x.78 (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.10.10.0 255.255.255.0
public static x.x.x.69 (inside, outside) STATIC_NAT_EXAMPLE netmask 255.255.255.255
internal access-group interface inside
Route outside 0.0.0.0 0.0.0.0 x.x.x.65 1
internal to the 10.10.10.0 ip access list allow 255.255.255.0 any
! Remote LAN is 192.168.10.0/24
access-list sheep extended ip 10.10.10.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
Can you post a "show sysopt run?
Try this command to enable proxy arp.
No outside sysopt noproxyarp
-
cannot access the rows of a table not nested element
What Miss me? I'm under Oracle 12 c (12.1.0.1.0)
CREATE TYPE dim_O AS OBJECT )dimension_id number
label_en varchar2()300( )
);
CREATE TYPE dim_T AS TABLE OF dim_O;
DECLARE
dims_t dim_T
START
SELECT CAST(MULTISET( ))
SELECT DIMENSION_ID LABEL_EN
DE DIMENSIONTABLE -actual physical table in oracle
OÙ DIMENSION_ID IN (3001 3002 3003()
) AS dim_T) "dim_rec"
BY dims_t
DE DOUBLE;
FOR I IN dims_t. FIRST... dims_t. LAST LOOP
DBMS_OUTPUT. Put_line() dims_t() I). dimension_id);
END LOOP;
-exit from the loop above is
-3001
-3002
-3003
-The following statement fails: cannot access the rows of a table not nested element
UPDATE TABLE ( SELECT dimension_id FROM TABLE (dims_t) ( )
Dimension_id SET = WHERE = dimension_id 3004 3003
-The following statement fails: cannot access the rows of a table not nested element
UPDATE TABLE ( SELECT dimension_id FROM TABLE (CAST (dims_t in dim_T () ) ( )
Dimension_id SET = WHERE = dimension_id 3004 3003
END;
I'm trying to understand this example very simple, but to no avail.
Can someone tell me why I get this error?
Thank you all in advance for your time.
Marc
What Miss me? I'm under Oracle 12 c (12.1.0.1.0)
CREATE TYPE dim_O () AS OBJECTnumber of dimension_id
label_en varchar2 (300)
);
CREATE TYPE dim_T AS TABLE OF dim_O;
DECLARE
dims_t dim_T;
BEGIN
SELECT CAST (TYPE MULTISET)
SELECT DIMENSION_ID, LABEL_EN
OF DIMENSIONTABLE -actual physical table in oracle
WHERE DIMENSION_ID IN (3001,3002,3003)
() AS dim_T) 'dim_rec '.
IN dims_t
FROM DUAL;
I'm IN dims_t.FIRST... dims_t.Last LOOP
DBMS_OUTPUT. Put_line(dims_t (i) .dimension_id);
END LOOP;
-exit from the loop above is
-3001
-3002
-3003
-The following statement fails: cannot access the rows of a table not nested element
UPDATE TABLE (SELECT dimension_id FROM TABLE (dims_t))
SET dimension_id = dimension_id = 3003 3004 WHERE;
-The following statement fails: cannot access the rows of a table not nested element
UPDATE TABLE (SELECT dimension_id FROM TABLE (CAST (dims_t as dim_T)))
SET dimension_id = dimension_id = 3003 3004 WHERE;
END;
I'm trying to understand this example very simple, but to no avail.
Can someone tell me why I get this error?
You get it because dims_t is an array of OBJECTS - not a table of scalars. But your SELECT statement returns scalar.
There IS NO such object, named "dimension_id"; It is an ATTRIBUTE of the object DIM_O. DIMENSION_ID is a SCALAR which, as says the exception, is a "No nested table element; If you cannot select/Update lines of it.
What you do is equivalent to the following:
DECLARE
dims_t dim_T;
number of dim_id;
dim_o design;
BEGIN
Design: = dim_o (3, 'ghi');
SELECT DIM_O (DIM_ID, LABEL) BULK COLLECT INTO table DIMS_T (d_o);
end;
/
ORA-06550: line 7, column 59:
PL/SQL: ORA-22905: cannot access the rows of a table not nested element
ORA-06550: line 7, column 1:
PL/SQL: SQL statement ignored
This SELECTION is trying to design it as a table when it's a SCALAR - so the same exception you get.
-
Cannot access the internet with bridged network - Windows 7 64 bit host, XPSP3 comments
I use VMPlayer v3.0.1 build-227600 on a PC under Windows 7 64-bit. My guest operating system is Windows XP Professional w/SP3.
I read all the messages on the use of NAT for the guest operating system can access the internet. But when I do that my guest is unable to access my Oracle server on my network. If I use Bridged my guest can access my Oracle server, but it cannot access the internet! How can I fix it? Shouldn't VMPlayer allow the guest OS to access the network and the internet? I need these two features.
Any help would be appreciated.
the simplest solution would be to add a second NIC to your comments, so that you can have bridged and NAT at the same time
___________________________________
VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary
-
We have implemented a cluster and our hosts, added vmkernel and have the right licenses. The migration option is available, but then we get the error message "cannot access the virtual machine configuration: cannot access the file [storage]" I thought about is because they do not work on a shared storage...
I had to think about iSCSI, but have not tried it before, and now I ask you, is the most optimal solution? We will cable from the server to the top with a SAS cable,
The servers are located in different parts of the building, I could put the other to the first server and their cable it but to avoid this, is there another solution? I can't use the data storage "migrate" since I don't have essential vmware more...
you need external shared storage and follow the right cable FC, iSCSI, or SAS. You can not just a two-server cable upward with a SAS cable and expect it to work like the discs are still local only. the other option is to search for virtual storage in which transform your disks local shared iSCSI volume
-
Cannot access the AIP SSM via ASDM
CISCO recommendations below:
Cannot access the AIP SSM via ASDM
Problem:
This error message appears on the GUI.
Error connecting to sensor. Error Loading Sensor error
Solution:
Make sure that the IPS SSM management interface is up/down and check his IP address configured, default gateway and the subnet mask. It is the interface to access the software from Cisco Adaptive Security Device Manager (ASDM) on the local computer. Try to ping the address of management of IPS SSM IP interface on the local computer that you want to access the ASDM. If it is impossible to do a ping check the ACLs on the sensor
----------------------------------------------------------------------------------------------------------------------------------------------
I've tried everything recommended above. I can ping the host ASDM the FW and the SSM-10 module. Well, I ping the host machine and the SSM of the ASDM. I opened as wide as possible ACL. I changed the IP addresses and masks several times. The management of the ASA port and the SSM and the PC are on the same subnet.
A trace of package from the PC to the SSM shows that it is blocked by an ACL rule, and yet I opened wide. I've seen this kind of problem before and it was solved by applying the double static NAT, but I don't know how to do that if all the IP addresses are on the same subnet.
Tried everything, need help from high level.
The IDM software that comes with ASDM does not support java 1.7. The portion of the ASDM ASA supports 1.7 but launch the IPS cmdlet works only with 1.6. The TAC enginner suggested that I use the IME (IPS Manager Express) which is available for free on the Cisco's (http://www.cisco.com/en/US/products/ps9610/tsd_products_support_general_information.html) Web site.
I've been playing with it today, and so far it seems to work pretty well.
-
CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION
Hello
I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match? Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.
Please see my full configuration:
Router #sh run
Building configuration...Current configuration: 8150 bytes
!
! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
Passwords security min-length 6
no set record in buffered memory
enable secret 5 xxxxxxxxxxx
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization exec default local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
!
No ipv6 cef
IP source-route
no ip free-arps
IP cef
!
Xxxxxxxxx name server IP
IP server name yyyyyyyyy
!
Authenticated MultiLink bundle-name Panel
!parameter-map local urlfpolicy TSQ-URL-FILTER type
offshore alert
block-page message "Blocked according to policy"
parameter-card type urlf-glob FACEBOOK
model facebook.com
model *. Facebook.comparameter-card type urlf-glob YOUTUBE
mires of youtube.com
model *. YouTube.comparameter-card type urlf-glob CRICKET
model espncricinfo.com
model *. espncricinfo.comparameter-card type urlf-glob CRICKET1
webcric.com model
model *. webcric.comparameter-card type urlf-glob YAHOO
model *. Yahoo.com
model yapoparameter-card type urlf-glob PERMITTEDSITES
model *.parameter-card type urlf-glob HOTMAIL
model hotmail.com
model *. Hotmail.comCrypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-2049533683
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2049533683
revocation checking no
rsakeypair TP-self-signed-2049533683
!
Crypto pki trustpoint tti
crl revocation checking
!
Crypto pki trustpoint test_trustpoint_config_created_for_sdm
name of the object [email protected] / * /
crl revocation checking
!
!
TP-self-signed-4966226213 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332quit smoking
encryption pki certificate chain tti
for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
license udi pid CISCO1905/K9 sn xxxxxx
licence start-up module c1900 technology-package datak9
username privilege 15 password 0 xxxxx xxxxxxx
!
redundancy
!
!
!
!
!
type of class-card inspect entire tsq-inspection-traffic game
dns protocol game
ftp protocol game
https protocol game
match icmp Protocol
match the imap Protocol
pop3 Protocol game
netshow Protocol game
Protocol shell game
match Protocol realmedia
match rtsp Protocol
smtp Protocol game
sql-net Protocol game
streamworks Protocol game
tftp Protocol game
vdolive Protocol game
tcp protocol match
udp Protocol game
match Protocol l2tp
class-card type match - all BLOCKEDSITES urlfilter
Server-domain urlf-glob FACEBOOK game
Server-domain urlf-glob YOUTUBE game
CRICKET urlf-glob-domain of the server match
game server-domain urlf-glob CRICKET1
game server-domain urlf-glob HOTMAIL
class-map type urlfilter match - all PERMITTEDSITES
Server-domain urlf-glob PERMITTEDSITES match
inspect the class-map match tsq-insp-traffic type
corresponds to the class-map tsq-inspection-traffic
type of class-card inspect correspondence tsq-http
http protocol game
type of class-card inspect all match tsq-icmp
match icmp Protocol
tcp protocol match
udp Protocol game
type of class-card inspect correspondence tsq-invalid-src
game group-access 100
type of class-card inspect correspondence tsq-icmp-access
corresponds to the class-map tsq-icmp
!
!
type of policy-card inspect urlfilter TSQBLOCKEDSITES
class type urlfilter BLOCKEDSITES
Journal
reset
class type urlfilter PERMITTEDSITES
allow
Journal
type of policy-card inspect SELF - AUX-OUT-policy
class type inspect tsq-icmp-access
inspect
class class by default
Pass
policy-card type check IN and OUT - POLICIES
class type inspect tsq-invalid-src
Drop newspaper
class type inspect tsq-http
inspect
service-policy urlfilter TSQBLOCKEDSITES
class type inspect tsq-insp-traffic
inspect
class class by default
drop
policy-card type check OUT IN-POLICY
class class by default
drop
!
area inside security
security of the OUTSIDE area
source of security OUT-OF-IN zone-pair outside the destination inside
type of service-strategy check OUT IN-POLICY
zone-pair IN-to-OUT DOMESTIC destination outside source security
type of service-strategy inspect IN and OUT - POLICIES
security of the FREE-to-OUT source destination free outdoors pair box
type of service-strategy inspect SELF - AUX-OUT-policy
!
Crypto ctcp port 10000
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 2
Group 2
!
ISAKMP crypto client configuration group vpntunnel
XXXXXXX key
pool SDM_POOL_1
include-local-lan
10 Max-users
ISAKMP crypto ciscocp-ike-profile-1 profile
vpntunnel group identity match
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
game of transformation-TRANSFORMATION TSQ
set of isakmp - profile ciscocp-ike-profile-1
!
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
!
interface GigabitEthernet0/0
Description LAN INTERFACE-FW-INSIDE
IP 172.17.0.71 255.255.0.0
IP nat inside
IP virtual-reassembly in
security of the inside members area
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
Description WAN-INTERNET-INTERNET-FW-OUTSIDE
IP address xxxxxx yyyyyyy
NAT outside IP
IP virtual-reassembly in
security of the OUTSIDE member area
automatic duplex
automatic speed
!
interface Serial0/0/0
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
no fair queue
2000000 clock frequency
!
type of interface virtual-Template1 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP nat inside source list 1 interface GigabitEthernet0/1 overload
IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
IP route 192.168.1.0 255.255.255.0 172.17.0.6
IP route 192.168.4.0 255.255.255.0 172.17.0.6
!
access-list 1 permit 172.17.0.0 0.0.255.255
access-list 100 permit ip 255.255.255.255 host everything
access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
access-list 100 permit ip yyyyyy yyyyyy everything
!
!
!
!
!
!
!
!
control plan
!
!
!
Line con 0
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
transport input ssh rlogin
!
Scheduler allocate 20000 1000
endA few things to change:
(1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.
(2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:
access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255
access-list 120 allow ip 172.17.0.0 0.0.255.255 everything
overload of IP nat inside source list 120 interface GigabitEthernet0/1
No inside source list 1 interface GigabitEthernet0/1 ip nat overload
(3) OUT POLICY need to include VPN traffic:
access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255
type of class-card inspect correspondence vpn-access
game group-access 121
policy-card type check OUT IN-POLICY
vpn-access class
inspect
-
cannot access the internet after upgrading to firefox 30.0 on windows 7
After the upgrade to firefox 30.0 on windows 7, cannot access the internet. FF 30.0 works OK under Vista
Sometimes it's because of your security software thinking that the upgrade may not be legitimate. You can consult this article: problems connecting to websites after Firefox update.
-
Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.
I cannot access all features and can be closed only by using force quit.
Please stop calendar and also the application of reminders, runs. Force quit if necessary.
Back up all data.
If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.
If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.
Launch schedule and see if there is an improvement.
-
I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?
Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
Turn on/off the menu bar is a new feature in version 3.6.
(Linux and OSX see: what happened to the file, edit and view menus? )
Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missingNavigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).
To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).
Mode full screen
http://KB.mozillazine.org/netbooks#Full_screenSee also:
Back and front toolbar buttons or others are missing
Customize controls, buttons, and Firefox toolbars -
42RL833 - latest Firmware installed and cannot access the YouTube app
I have 42RL833 Toshiba which is updated to the latest firmware, however I still cannot access the application on my YouTube. I get an error saying that Youtube XL is no longer supported.
What can I do to fix this?
> I get an error saying that Youtube XL is no longer supported.
Google has stopped the YouTube XL service and, therefore, this service isn't available anymore.
http://www.Toshiba.EU/innovation/generic/YouTube-XL/You can read details here:
https://support.Google.com/YouTube/answer/3123170?hl=enIt also seems that YouTube XL has been replaced by YouTube Leanback Lite:
http://www.YouTube.com/leanbacklite
See also:
https://support.Google.com/YouTube/answer/3153576#There is also a note that if you can connect your computer to your TV, you can continue to use the YouTube TV-optimized experience by visiting youtube.com/tv.
-
Hello
My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?
Thanks in advance.
Hello @jerome256,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.
I understand that you are having a problem with your WiFi and wanted to help you!
You are trying to access WiFi through router? If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router. Check that the router is connected to the internet. If you have more than one router, then you can ensure that you are connected to the correct router. You can also try unplugging the router for about 30 seconds, and then reconnecting it. Please consult the following document, as it can help solve the problem for you:
HP PC - Troubleshooting wireless network and Internet (Windows 10)
Please let me know if this information has been helpful by clicking the thumbs up below.
Have a great day!
-
Hello
I have a Windows 2003 X 64 server and since a week ago everything works fine.For a week or two when I try to run an X 86 application, I always get this error:"Windows cannot access the specified device, path or file.If I run a x 64 apps everything works fine.What made a mistake?Thank youHello
Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please post your question in the TechNet forums. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en/category/WindowsServer/
-
Original title: problems cannot do anything
Windows cannot access the specified device, path or file. You can't have__appropriate the permissions to access the item. I get it all the time can not download anything
Hi birdylod,
· What version of the operating system is installed on the computer?
· You did changes to the computer before the show?
· You use Internet Explorer? If so, what version are you using?
· What files you download?
Follow these methods.
Method 1: Performs a search using the Microsoft safety scanner.
http://www.Microsoft.com/security/scanner/en-us/default.aspx
Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
Method 2: Follow these steps:
Step 1: Start the computer in safe mode with network and check if the problem persists.
Startup options (including safe mode)
http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.
Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.
Method 3: Scan the file system (CFS) auditor to repair corrupted files.
How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
http://support.Microsoft.com/kb/929833
For reference:
What to know before applying permissions to a file or folder
-
I cannot access the application 'contact me' when a web site and receive the answer "Default Mail Client not properly installed" instead of going on the requested site.
How can I fix this problem?
Separated from the:
CrystalBall © SEZ...
Unlike Windows XP & Vista, Windows 7 does not include a default email Client. [What were thinking?]
You will need to install a (e.g. MS Outlook;) Windows Live Mail; Thunderbird) , and then set it as a default for mail in CUSTOM (<>) article in Set Program Access and defaults of the computer , then restart your computer before any function send to or MailTo will become available.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In these forums, you will find support for Windows Live Mail: http://windowslivehelp.com/forums.aspx?productid=15
Maybe you are looking for
-
Need help with the upgrade/reload iPhoto
iPhoto constantly crashed when I opened it. He didn't stay open long enough to even load the library. By reading the forum I found what I thought might work, so I've renamed it my library (which is more than 300 gig) "OLD iPhoto library" and put i
-
Question about the extension of RAM for Satellite A50-522
Hello I have a Satellite A50-522, with a Pentium M 715 @1. 5 Ghz processor and Intel 855GME chipset. To expand its RAM I referred to the Spain/Toshiba support website and I bought the PA3313U-2M1G (1 GB SDRAM 166 MHz DDR333/PC2700) via amazon.com. It
-
Properties of the Windows folder
I want to know how to hide a folder programmatically in WIndows using LabView?
-
Password forgotten for V3 - 471G
I have an Acer V3 - 471G (version i7-3610QM). A few years back I put a password in the BIOS options to prevent access to him, but since I did not use the menu of the BIOS for a while, I forgot and am looking for a way to delete or reset. I checked on
-
PDF files can not detect my hp printer
Hello I can not print all of my pdf files. Whenever I clicked on the button print, it says "before you start printing tasks for example page put in place or document printing, you must install a printer. How is that possible? I recently installed my