Cannot connect to wrt54gl Web configuration page.

Similar Questions

• WRT54G V8 cannot connect to the web-based configuration page?

  Earlier, I reset my router and was able to use 192.168.1.1 to visit the configuration page based on the web while trying to restore a home network, now that I have a new computer using Windows 7 that can not use the easylink advisor. I was able to get on the page update my SSID and WEP key. But when my wireless devices were still having problems to you connect to the internet, I tried to go back to the page and found that I can't seem to connect, even if my office is able to connect to other websites very well.

  Anyone know what I can do wrong? I use Verizon DSL. I was able to ping to the router and all tests have shown that it was connected fine, but I still can't get on the configuration page and my laptop can't connect to the network. I tried to reset the router again and still nothing. And Yes, I went through several cycles of power. I have also tried to move if the network card on my computer, but the computer said it was impossible to create a card for him, although at the time I had listed as a home network.

  Wireless on 192.168.1.1 connections often fail.  Using the router configuration pages, always use a computer that is connected to the WRT54G.

  If the above does not solve your problem, so here are my other tips to see the router configuration pages:

  You don't need an Internet connection. 'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  Point your browser to 192.168.1.1, and then connect to your router. Your username must be left blank. Your password is "admin" (without the quotes), unless you changed it.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  Some Zone Alarm users reported that the addition of 192.168.1.1 to their address list "of trust" solved the problem. This trick can also work with other firewalls.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. A report with this problem and also specify the brand and exact model of your modem (not router) number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system.  The router should work, but you will need to configure your router again from scratch.  If you have saved a router configuration file, DO NOT use it.

  If you still have problems, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• WRT320N cannot not get IP address - using only 1 - no internet access - wired port hang web configuration pages

  You just bought Linksys WRT320N as a replacement for Netgear MR814.

  Cannot connect to internet using Linksys WRT320N.

  Installation program:

  ISP: Cox Communications (cable)

  Firmware: v1.0.03 build 010 July 24, 2009

  1 Wired - port 1 - for Windows XP SP 3 Dell Desktop

  Attempts to install:

  1 tried to set up using the installation CD.  Spread the slightest error with error 302: internal error. tried this 3 times

  2A through the reset, power off, procedures.

  3 Ping 192.168.1.1 = success

  4. connected to 192.168.1.1 via web browser

  5. set the MAC Address = MAC address of the computer

  6. the MTU value = Auto (1500).  Also tried manual 1492

  Could not get the IP address by using the version of IP address and IP address renew.  Address Internet IP still = 0.0.0.0

  Note that the web page will be still stuck after perfoming some actions (such as after switching between the tabs).  Message at the bottom of the browser is "Wating for http://192.168.1.1/Status_Router.asp.  And the hourglass on the screen away.

  Note that the old Netgear router still works fine and I am currently connected to the internet via the Netgear router.   I'd appreciate any help getting the new Linksys router connection/operation/obtaining of internet and IP address.

  Thanks for your help.

  I do not know where I was unclear: you wrote before you used the function of the cloning mac address on the WRT to clone the MAC address of the PC. In this way the WRT "pretended" to be the PC if you connect to the internet port WRT to your modem.

  However, the PC is not the device you used before you connect to the internet. The PC was not the device that was connected to the modem before. If you connect the computer directly to your modem it will either be an IP address. There will be no internet.

  The problem is that your ISP only allows you to have an active internet connection single at some point. If you plug in a different device with a different MAC address to your modem this device won't get an IP address. That you have connected the Netgear router to your modem and you have internet, then you need to clone the MAC address of the Netgear router. This is the device that is connected to your internet connection and it is the MAC address that your ISP has locked your internet connection.

  So, once again: clone the MAC address of the router netgear (internet or WAN port MAC address) of your Linksys router. Then the Linksys's router Netgear and your ISP should accept the Linksys router. The netgear router should have a status page in the web interface, showing you the right MAC address to be cloned.

• Cannot connect to my Web site on Microsoft arrived.

  I NEED URGENT ASSISTANCE. I filled the problem page to report to microsoft now 2 times. and 2 I have no RESPONSE TIME. I can not CONNECT to my Web site period. I NEED URGENT ASSISTANCE. I know that my user id its * address email is removed from the privacy * ... I don't remember my period of password that I tried all my usual passwords and nothing works the period. I clicked on reset password and all I get is an error page saying technology contact support and cannot reset my password period. I DO WORK on MY WEB site I HAVE no access period. I cannot NOT UP DATE IT or NOTHING and I HAD to have an EMERGENCY CONTACT person on this issue and RESOLVE it IMMEDIATELY. THANK U

  No one here can help you.  We are voluntary, not Microsoft employees, helping users of windows with dots and security questions.  You must go through the appropriate channels to support Live or Hotmail for assistance on their part.

• WRT160NL cannot connect to the web interface after firmware update

  I've updated the firmware to unofficial http://mirwifi.org/download/fw/WRT160NL/wrt160nl-0.1.3-pre5.bin and since then I can not connect to the router through the web interface. What can I do? Is it possible to update the firmware to the official without web interface? Thanks in advance for any help.

  The router's default IP address is 192.168.1.1. Try to ping the IP address of the router and check if you get answers from the router.

  Open the Internet browser and in the address bar type http://192.168.1.1. See if you can open the router configuration page.

  If this does not work then you can try to update the official firmware on the router using the TFTP.exe file.

  Disable the firewall on your computer. Connect the computer to the router with the Ethernet cable.

  (1) download the official firmware file from the site Web of Linksys router. Save it to your computer.

  (2) download the tftp site Web of Linksys. Follow this link to search for the file tftp. You'll find downloads for router BEFW11S4. Select the version 3.2 hardware and download the installation wizard. Save it to your computer.

  (3) run the installation wizard. In the server box, type the IP address of your router. In the password box, type the password of the router. Default password for the router is admin. Find the file of the official firmware you have already downloaded and click on upgrade.

  See if it works.

  After upgrading the Firmware on the router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• Why "problem loading page" appears when I try to start firefox? I can access the page relevent medium of internet explorer, but firefox cannot connect to the web.

  A few days ago Firefox has stopped working when you use the shortcut or exe. file. The message http://en-gb.start3.mozilla.com/firefox?client=firefox-a & rls = org.mozilla: en - GB:official appears, even if when I paste this address in internet explore it works. What is preventing firefox to connect?

  One possible cause is security software (firewall) that blocks or limits Firefox without you informing on this subject, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox in the list of permissions in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox.

  See Server not found - the problems of connection and Configure the firewall so that Firefox can access the Internet and http://kb.mozillazine.org/Firewalls

• RV120W cannot connect after restoring boot configuration?

  Hi all, being new to RV120W, I met a problem one would like to know if anyone of you have met/never been able to reproduce the following problem:

  (1) I clicked on settings of backup / restore-> mirror copy at startup. The router restarts. So I can not connect me to it with any username and password. Then I need to do a factory reset.

  (2) I clicked on settings of backup / restore-> configuration of mirror backup to perform a backup, and then press the restore startup configurations. The router restarts.

  So I can not connect me to it with any username and password. Then I need to do a factory reset.

  (3) I clicked on settings of backup / restore-> boot configuration of backup to perform a backup, and then press the restore startup configurations. The router restarts. So I can not connect me to it with any username and password. NO factory setting is necessary.

  Firmware tested: 1.0.4.10, 1.0.5.6

  My question:

  (a) is this a bug? (Or just my bad/misunderstanding?)

  (b) means that, if set to true, before performing a backup configuration, I have to restart once and save the rebooted boot configuration?

  Thanks a lot for your help!

  Johnny

  Hi Johnny, if you did as you described, it seems that you write an empty config on the startup configuration. The step that I see missing is where you specify the file to load.

  So to confirm... you click on the backup button and it generated the backup file that you saved on a computer. Then you come this file, he chose and chose the option to restore and then your credentials did not work?

  -Tom
  Please mark replied messages useful

• Cannot connect to the Web Interface using IE9 idrac6

  Hello world

  I was appalled last Saturday when I have downloaded voluntarily a remote server knowing that I would use the idrac to bring up, to see that when I tried to connect to the idrac he wouldn't my password.  I had to call the customer and send them to the site on Saturday night and I was very angry about this.

  After being, upward, that I tried several times to connect remotely and it still would not accept my password, I tried the reset of the OM Server page, but not to go.  I would put my password and it should Flash quickly "Access please wait" at the bottom of the screen, and then he would just go back to the login screen.

  I thought maybe it was a browser security issue, so I tried to add the remote site to my trusted sites and lowering of safety, but it did not help, so I tried various is to say like compatibility mode settings and still no go.  This has been tried on 2 different machines to Windows 7 with IE9, a x 64 and x 32.  Then I thought that I would try Chrome instead and it worked fine...

  So I tried a VM XP with IE8 on it, and it worked well.  It seems so - that IE9 is the culprit.

  I called in the systems management team and we tried which helps some ActiveX controls in the zone of confidence, but it did not help and he me basically what IE9 doesn't play well with the drac's and they are working on an update to fix the problem.

  This is perfect and I accept it, because I know I can get with another browser if I had to, but someone has actually managed to make it work with IE9?

  I have the same problem. But, I have found that if 'Remove' all under 'Browser history' (check everything: Cookies, history, temporary Internet files, etc...) it will allow me to connect and work for a while. Then I after a bit, it stops working. So again, I delete all log and work harder. This was a major pain in the rear lower.

  Oh, but I never have the ActiveX/native console to work. But I'm just using the Java plug-in.

• Cannot connect to a Web site

  Hi, I can't connect to a website I get "error could not connect", this is the only site that I have trouble with
  It's Academyofhomebusiness

  Cookies must be enabled, and I think that Java (no script)

• Big Brother Live Feed will not play or cannot connect to the Web site.

  I can't connect to CBS.com to watch Big Brother Live Feeds. When I hit the button 'connect', or a 'secure connection' error or nothing happens and stays of sign - in the pop-up on the idle screen and won't go away. CBS.com has two different choices to click to connect, or working. It will work in Internet Explorer.

  refer to

  • Resolve the error message "secure connection failed".

  and

  • How to clear the cache of Firefox

  Items to solve this.

• IE 8 cannot connect to the web site because of restrictions on computer

  By clicking on a link Web translates into a negative answer above.

  The first Question of troubleshooting: If the problem is new, what has changed between the time things worked and the time they do not have?

  The second issue of Windows troubleshooting: what is the status of virus/malware of the machine? If you think it's clean, what programs (and versions) allows you to determine this?

  Make sure that the computer is clean:
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Post back with answers/results for additional assistance if necessary. MS - MVP - Elephant Boy computers - don't panic!

• Cannot connect to the web portal of VMware Data recovery

  When I try to connect, I get the following error. Not sure when this started happening. What can I do to fix this?

  'Failed to authenticate the user. Please try again. »

  

  The password is the default 'vmw@re '... I did not in place while I was trying all our admin passwords.

• HP Deskjet 3545: How to reset the password of admin for HP Deskjet 3545. Cannot connect to the administrator settings page.

  I put a password for the printer. And whenever I try to open a session with him, he keeps asking the user name and password. So I want to reset the password or leave the field empty. Please help urgently.

  Hi @flame_ardor,

  Welcome to the Forums of HP Support! I understand you want to reset the password for your HP Deskjet Ink Advantage 3545.

  You should be able to do this by restoring the default network settings in the front panel of the DJ 3545:

  On the printer control panel, press the Wireless button. Wireless menu.

• Why cannot connect with DB after control DB console configure NetMgr/NetCA?

  People,
  
  Hello. I am running Oracle Database 11 GR 1 material in Oracle Linux 5.
  
  Before you configure Net Manager/Net CA, database https://localhost.localdomain:1158 control console / em, SQL * more and Developer SQL to connect to the Instance of database DB1. All instructions SQL runs correctly.
  
  After Configuration Manager Net/NetCA, all the tools of Admin above cannot connect to the Instance of database DB1 is the only case of DB.
  
  What I've done is added 2 headphones more in Net Manager.
  
  The original listener does not change which properties are: Protocol TCP/IP, Host localhost, Port 1521
  
  Can any folk tell me what causes all the administrative tools cannot connect with DB1 after configure NetManager/NetCA?

  user8860348 wrote:
  People,

  Hello. Thanks much for the reply.

  ORACLE_HOME/bin directory, the command. / sqlplus SYS/SYS used to run correctly after the installation of the database. But after stopping Linux operating system, the command. / SYS/SYS cannot connect with Dabase more sqlplus.

  I think that the command. / emctl start dbconsole should start to the top of the database. Am I wrong?

  NO, you're not correct.

  >

  Is there another way to start the database?

  sqlplus
  / as sysdba
  startup

  as shown below
  BCM@BCM-laptop: ~ $ sqlplus

  SQL * more: Production release 11.2.0.1.0 Sun Jul 17 20:05:09 2011

  Copyright (c) 1982, 2009, Oracle. All rights reserved.

  Enter the user name: / as sysdba
  Connect to an instance is idle.

  SQL > startup
  ORACLE instance started.

  Total System Global Area 1553305600 bytes
  Bytes of size 2213656 fixed
  1275070696 variable size bytes
  268435456 buffers of data bytes
  Redo buffers 7585792 bytes
  Mounted database.
  Open database.
  SQL >

• WANT to 114 does not connect to the Web server

  Have installed a 114 WANT, everything works except for the webservices - wireless eprint etc.

  I tried everything-

  1 re-install services - error cannot connect to the web server

  2. Update - error cannot connect to the web server

  3 give the static IP address

  4 restore the default settings

  I have an internet connection on all computers.  Can someone give me a hint on how to get Web services to work?

  Hi sbenzie,

  How your printer is currently connected to the network? Via Ethernet or wireless? What is your current router / network configuration? That shows your printer because it is the IP address? What happens when you try to launch applications?

  Not yet given the information above, here's what I would try.

  I suggest to reconnect the printer to the network by running the Wireless Setup Wizard and attempt to restart the web services. If this is not enough, you may change some DNS settings in printers EWS (built-in web server) to do this, put the IP address in a browser window on your PC.

  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.

  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.

  Now try to connect to Web Services again.