WRT54G V8 cannot connect to the web-based configuration page?

Similar Questions

• Possible security for the Web-based Configuration

  My colleagues and I found something very interesting today... Despite having configured the FTP security settings (which have been confirmed to set up and in funcitoning. I can't open an FTP session to our remote target without specifying a username admin and the password) If you open the configuration tool based OR web in a browser, you can send via FTP to and from the target using the file remote browser without being connected to all! Everyone knows this?

  Apparently, these permissions are separate from FTP, but you can define these special permissions on the page of the security configuration for the web-based configuration utility.

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• WRT160NL cannot connect to the web interface after firmware update

  I've updated the firmware to unofficial http://mirwifi.org/download/fw/WRT160NL/wrt160nl-0.1.3-pre5.bin and since then I can not connect to the router through the web interface. What can I do? Is it possible to update the firmware to the official without web interface? Thanks in advance for any help.

  The router's default IP address is 192.168.1.1. Try to ping the IP address of the router and check if you get answers from the router.

  Open the Internet browser and in the address bar type http://192.168.1.1. See if you can open the router configuration page.

  If this does not work then you can try to update the official firmware on the router using the TFTP.exe file.

  Disable the firewall on your computer. Connect the computer to the router with the Ethernet cable.

  (1) download the official firmware file from the site Web of Linksys router. Save it to your computer.

  (2) download the tftp site Web of Linksys. Follow this link to search for the file tftp. You'll find downloads for router BEFW11S4. Select the version 3.2 hardware and download the installation wizard. Save it to your computer.

  (3) run the installation wizard. In the server box, type the IP address of your router. In the password box, type the password of the router. Default password for the router is admin. Find the file of the official firmware you have already downloaded and click on upgrade.

  See if it works.

  After upgrading the Firmware on the router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• Errors of certificate RV042 browser by connecting to the web-based GUI

  I put the RV042 for QuickVPN access.  The router config recommend turning on HTTPS in the firewall when using QuickVPN.  The side effect of this is any web browser get me certificate errors and warns me not not to continue to connect to the router config.  How can I fix this so the browser does not throw these messages?

  Router Linksys brand is using the latest firmware for this material (1.3.13.02 - tm)

  Hi Tim,.

  The deeper issue, it's because of the certification on the cisco.com area which you do not own. And when you connect to your router probably with your own domain name or ip address that it compares this information with the information stored in the certificate. Because it will never match across is a mistake. The RV0xx series routers are not able to install 3rd party certificates, then it will not be able to resolve in their current version. I'm not aware of any decision to modify the code to solve this problem. The RV220W and SA500 series routers have the ability to install a third-party certificate. The SA is the only other model that has the ability in the line of small business to double WAN.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• Cannot connect to the Web Interface using IE9 idrac6

  Hello world

  I was appalled last Saturday when I have downloaded voluntarily a remote server knowing that I would use the idrac to bring up, to see that when I tried to connect to the idrac he wouldn't my password.  I had to call the customer and send them to the site on Saturday night and I was very angry about this.

  After being, upward, that I tried several times to connect remotely and it still would not accept my password, I tried the reset of the OM Server page, but not to go.  I would put my password and it should Flash quickly "Access please wait" at the bottom of the screen, and then he would just go back to the login screen.

  I thought maybe it was a browser security issue, so I tried to add the remote site to my trusted sites and lowering of safety, but it did not help, so I tried various is to say like compatibility mode settings and still no go.  This has been tried on 2 different machines to Windows 7 with IE9, a x 64 and x 32.  Then I thought that I would try Chrome instead and it worked fine...

  So I tried a VM XP with IE8 on it, and it worked well.  It seems so - that IE9 is the culprit.

  I called in the systems management team and we tried which helps some ActiveX controls in the zone of confidence, but it did not help and he me basically what IE9 doesn't play well with the drac's and they are working on an update to fix the problem.

  This is perfect and I accept it, because I know I can get with another browser if I had to, but someone has actually managed to make it work with IE9?

  I have the same problem. But, I have found that if 'Remove' all under 'Browser history' (check everything: Cookies, history, temporary Internet files, etc...) it will allow me to connect and work for a while. Then I after a bit, it stops working. So again, I delete all log and work harder. This was a major pain in the rear lower.

  Oh, but I never have the ActiveX/native console to work. But I'm just using the Java plug-in.

• WRT110-problem accessing the Web-based Setup Page

  I can't access the configuration page based on web for the WRT110 router I have. I am able to make a connection on two computers without the router, but when I add them I get an error message in my browser.

  I tried to access the configuration page based on the web both of my computers and some information were followed by Ecritel.net, but I'm having no luck. I receive the following error message "missed connection: connection to the server was reset while the page is loading." The network link was interrupted for negotiating a connection. Please try again. »

  Any advice would be greatly appreciated! Thank you!

  Actually, I get a different error message now. I made a few adjustments to things like the start menu, which is a problem before. Here is the new error message I received:

  Network timeout Server 192.168.1.1 takes too long to respond. The requested site did not respond to a connection request and the browser has stopped waiting for a response

  Can experience the high demand server or a temporary outage? Try again later.

  Are you unable to navigate to other sites? Check the computer's network connection.

  Is your computer or a network protected by a firewall or proxy? Incorrect settings can interfere with browsing the web.

  Still having trouble? See your network administrator or your Internet service provider for assistance.

  Someone at - it ideas? I searched on the Internet, but nothing I've tried works. Thank you in advance!

• missing components of the web-based configuration

  Hi all

  I have two controllers cRIO-9074 on my network, both with the OR-RIO 4.0 software installed.  When I open a web browser to display utilities 'OR configuration & monitoring Web-based', a cRIO not show four of the eight tools on the left side of the interface of Silverlight.  Missing the Console Remote File Browser, Web Server Configuration and installed the Configuration Tools.

  I would like for the user of this system be able to download its data files, every day or so using the remote file browser, so this feature would be nice to have. Any ideas?

  Kind regards

  Marvin Perry, DRESSED

  
  

• Big Brother Live Feed will not play or cannot connect to the Web site.

  I can't connect to CBS.com to watch Big Brother Live Feeds. When I hit the button 'connect', or a 'secure connection' error or nothing happens and stays of sign - in the pop-up on the idle screen and won't go away. CBS.com has two different choices to click to connect, or working. It will work in Internet Explorer.

  refer to

  • Resolve the error message "secure connection failed".

  and

  • How to clear the cache of Firefox

  Items to solve this.

• Why "problem loading page" appears when I try to start firefox? I can access the page relevent medium of internet explorer, but firefox cannot connect to the web.

  A few days ago Firefox has stopped working when you use the shortcut or exe. file. The message http://en-gb.start3.mozilla.com/firefox?client=firefox-a & rls = org.mozilla: en - GB:official appears, even if when I paste this address in internet explore it works. What is preventing firefox to connect?

  One possible cause is security software (firewall) that blocks or limits Firefox without you informing on this subject, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox in the list of permissions in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox.

  See Server not found - the problems of connection and Configure the firewall so that Firefox can access the Internet and http://kb.mozillazine.org/Firewalls

• IE 8 cannot connect to the web site because of restrictions on computer

  By clicking on a link Web translates into a negative answer above.

  The first Question of troubleshooting: If the problem is new, what has changed between the time things worked and the time they do not have?

  The second issue of Windows troubleshooting: what is the status of virus/malware of the machine? If you think it's clean, what programs (and versions) allows you to determine this?

  Make sure that the computer is clean:
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Post back with answers/results for additional assistance if necessary. MS - MVP - Elephant Boy computers - don't panic!

• Cannot connect to the web portal of VMware Data recovery

  When I try to connect, I get the following error. Not sure when this started happening. What can I do to fix this?

  'Failed to authenticate the user. Please try again. »

  

  The password is the default 'vmw@re '... I did not in place while I was trying all our admin passwords.

• Cannot connect to wrt54gl Web configuration page.

  I can't access the web-based configuration page. The default user name and password have not changed. When I type in the admin password to default the connection disappears and the reappers. No wrong password message or anything. I ping the router and the router comes back 4 packs. Devices on the network are working well, I can not access the installation page either. I don't know if it's the ideal shape for this or not, so if it's not made me know.

  Thanks for any help!

  I do not recommend updating the firmware that would erase the settings anyway. Just reset and reconfigure.

• down loaded more recent firefox and now it does not connect to the web.

  Just did the new down load and restarting the Fire Fox cannot connect to the web.
  No problem before this new version.
  IE works fine. Chrome works very well.
  Only fire fox does not.

  You get this error message.

  See also article Firefox cannot load websites, but can other browsers .

• WANT to 114 does not connect to the Web server

  Have installed a 114 WANT, everything works except for the webservices - wireless eprint etc.

  I tried everything-

  1 re-install services - error cannot connect to the web server

  2. Update - error cannot connect to the web server

  3 give the static IP address

  4 restore the default settings

  I have an internet connection on all computers.  Can someone give me a hint on how to get Web services to work?

  Hi sbenzie,

  How your printer is currently connected to the network? Via Ethernet or wireless? What is your current router / network configuration? That shows your printer because it is the IP address? What happens when you try to launch applications?

  Not yet given the information above, here's what I would try.

  I suggest to reconnect the printer to the network by running the Wireless Setup Wizard and attempt to restart the web services. If this is not enough, you may change some DNS settings in printers EWS (built-in web server) to do this, put the IP address in a browser window on your PC.

  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.

  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.

  Now try to connect to Web Services again.