Similar Questions

• Cannot access the Web server in the DMZ from the inside using IP global

  Hi all

  I hope it's a very simple question.

  I'm running a PIX 515 firewall v6.3. I set up a Web server in my DMZ and use static NAT for re-branded it overall static IP address. Access from the outside of the demilitarized zone works remarkably well. I can access inside the interface Web site using the internal IP, but I can't access it from inside interface using the global IP are entrusted to him.

  Is there a particular reason why this would not be allowed? My feeling was that the request would be forwarded via the external interface (as it is a global IP address) and then be bounced back by my sense of the ISP the request would come to the new external interface (as the static NAT is applied to the external interface).

  However if I try and access the global IP from my inside interface, then the browser can not find the server.

  can someone explain why this is so? Any information would be appreciated.

  see you soon,

  Wayne

  ---------------------------------

  6.3 (3) version PIX

  interface ethernet0 100full

  interface ethernet1 100full

  interface ethernet2 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif dmz security50 ethernet2

  hostname helmsdeep

  domain p2h.com.sg

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  no correction protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  No fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  acl_out list access permit tcp any host 203.169.113.110 eq www

  access-list 90 allow the host tcp 10.1.1.27 all

  pager lines 24

  debug logging in buffered memory

  Outside 1500 MTU

  Within 1500 MTU

  MTU 1500 dmz

  IP address outside pppoe setroute

  IP address inside 192.168.1.1 255.255.255.0

  dmz 10.1.1.1 IP address 255.255.255.0

  no failover

  failover timeout 0:00:00

  failover poll 15

  No IP failover outdoors

  No IP failover inside

  no failover ip address dmz

  location of PDM 202.164.169.42 255.255.255.255 inside

  location of PDM 202.164.169.42 255.255.255.255 dmz

  location of PDM 10.1.1.26 255.255.255.255 dmz

  location of PDM 10.1.1.26 255.255.255.255 outside

  location of PDM 172.16.16.20 255.255.255.255 outside

  location of PDM 192.168.1.222 255.255.255.255 inside

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  Global (dmz) 1 10.1.1.101 - 10.1.1.125

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  NAT (dmz) 0-list of access 90

  NAT (dmz) 1 0.0.0.0 0.0.0.0 0 0

  static (dmz, external) 203.169.113.110 10.1.1.27 netmask 255.255.255.255 0 0

  Access-group acl_out in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.222 255.255.255.255 inside

  enable floodguard

  string fragment 1

  Console timeout 0

  Terminal width 80

  Code v6 pix or less don't let you have traffic "back" or return flow via the same interface on which it was sent. Having also your bounce back off of an external server traffic is never a good idea, because you won't be able to distinguish which and rogue attacks by spoofing someone outside your network.

  Since you are using pix 6.3 code, you may be able to outside the NAT. Add this static to your config:

  static (dmz, upside down) 203.169.113.110 10.1.1.27 netmask 255.255.255.255 0 0

  You may need to run a clear xlate after adding the new static statement. Note that the interfaces: it's demilitarized zone, inside inside, dmz.

  I would like to know if it works.

• Not able to enable the web server in exe

  Hello

  I have a problem with starting a web server. I Vi which allow the address of the directory to be published and after that it makes the stream server. And there are a few jpg files and some html files in the directory. And jpg files are attached to html files. And then there are a few vi which adds the other façades Vi:s of images. And that the program runs the image files in the directory on the server are written (updated). So the point is access through a Web browser on the site where some hyperlinks and behind links that there are photos of a few front panels. And my applications automatically updated images.

  Problem is that the server will not go when I've built and run the application. In the development environment, it works perfectly. I tried this on another PC too, but the exe will not connect to the server on one of the computers.

  Need help, thank you

  There is the attached web server startup file.

  Version is 8.2

  Hello!

  http://digital.NI.com/public.nsf/allkb/3B2160B128EE09A886256B60006FFA66

  Run in LabVIEW application to run Web server is different from the development environment. Please, look at the link above and try it if she could help you.

  ARO

  Do Nguyen

  National Instruments technical support

• PHP form script is missing from the web server or PHP is not properly configured on your web hosting provider. Help - I get this message on my site when the form is filled out and you press send... Check if the form PHP script has been downloaded correctl

  PHP form script is missing from the web server or PHP is not properly configured on your web hosting provider. Help - I get this message on my site when the form is filled out and you press send... Check if the form PHP script has been downloaded correctly, contact your host about the configuration of PHP.

  Hi Graham,

  If you, please add your site to this link ( http://my-site.com/scripts/form_check.php ) and make sure that all green checkmarks are appearing. If they don't, let us know what errors you seem to receive and include the link to your site.

  In addition, check out this guide on the forums of Muse troubleshooting: Troubleshooting Muse form used on the servers of third party Widgets

  I hope this helps!

  Emily

• start the Web server in different folders

  I developed a compiled VI (Smarts - Net .exe) that has been designed to operate in a specific folder (\Smarts-Net) and activated the Server Web page of Smarts - Net .html in the same folder.  So far so good.

  The application receives data in real time produced another of our programs and generates graphs to show "what happens".

  My clients would like run multiple instances of my program for their customers, but want to isolate their customer 'A' customer 'B' so that they cannot display the data on the other.  I can start my application using different IP ports so that I can have multiple views, but I want to further isolate the data of the customer in different folders.

  I did a 'manager' program that will create a subfolder of the folder in my main application (\Smarts-Net) so that it would appear as "\Smarts-Net\JobA" and copy all the files in the main folder in the new subfolder.  I then change the of Smarts - Net .ini file with the new pathname of the file and the new port like this number:

  [Smarts-Net]
  server.app.propertiesEnabled = True
  Server.OLE.Enabled = True
  Server.TCP.servic = "My Server computer/VI"
  server.vi.propertiesEnabled = True
  WebServer.DirectoryIndex = "index.htm"
  WebServer.LogEnabled = True
  WebServer.LogPath=C:\Smarts-Net\Logs\Smarts-Net.log
  WebServer.MimeTypes = (a LOT of Mime types in here... I left aside for this post)
  WebServer.Port = 9501
  WebServer.Enabled = True
  WebServer.RootPath=C:\Smarts-Net\JobA
  WebServer.TcpAccess = "" + c * ' "
  WebServer.ViAccess = "' + * '"
  DebugServerEnabled = False
  DebugServerWaitOnLaunch = False

  After you change the .ini file, I start the application (Smarts - Net .exe) to the new folder.

  This is where I need help.  If I try to display the VI from another computer using an address like http://snape:9600/JobA/Smarts-Net.html, I get an "HTTP 404 - File not found" error.  But, if I try to http://snape:9600 / Smarts - Net .html, I get the VI Panel!

  Thus, it seems that I can change the Port in the .ini file, but not the RootPath.  Does anyone know how to get the html to load from a different folder from the one specified when I created the application code?

  Hello Steve,.

  From your description it looks that the web server is already doing what you say you need for.

  There is a difference between the URL path, the path that is entered in the browser and the path of file system, the location of the file on the disk.

  The WebServer.RootPath token specifies the directory of the file system that corresponds to the root directory, "/", in the URL. You have specified C:\Smarts-Net\JobA as root your path so all files in this directory will be the URL of the http://mycomputer:myport / myFile. If you want the URL of http://mycomputer:myport/Logan/myFile then you need to have your root C:\Smarts-Net\ directory.

  Does make sense?

  Nathan

• Activation of scripts on the Web server

  I found this, but cannot locate Scripting on the Web Server: Configuration page

  Activation of scripts on the Web server

  To use the script with a Web service, you must enable the feature on the Web of LabVIEW server. In LabVIEW, select the script on the Web Server: Configuration page in the dialog box Options to enable the use of scripts on the Web server.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7738

  It seems that scripting is enabled automatically.

• run the Web server in vmware

  Hello
  I run the Web server in the os(xp pro) host and now I want to run the Web server in the guest operating system
  I put things in the host operating system, follow
  router setting page (shared ip settings page)
  1 DHCP using OFF
  2 DMZ host server using on 192.168.10.201
  3. setting of virtual server 192.168.10.201 port TCP port internal external port 81 81
  TCP/IP
  1 use the following IP 192.168.10.201
  2 gateway 192.168.10.1
  3. the DNS settings of
  4. on the Advanced tab > Internet connection sharing > VMware Network Adapter VMnet 8
  for now, when someone tries to access my WAN IP then page host server is apear (from external network)
  If I stop server Web host then cannot access my WAN IP

  and in VMware, I put the (Windows XP Pro)
  TCP/IP configuration
  1 use the following IP 192.168.88.201
  2. default gateway 192.168.88.2
  3. the DNS settings of
  4. click the guest OS tab and click Edit > virtual network editor > NAT VMnet host is VMnet8
  5. setting NAT > Port forwarding > Add >: host port 81 machine virtual ip address 192.168.88.201 port 81
  and at the moment access to 192.168.88.201 in the guest operating system is ok the page is apear
  but nothing is apear when try and access my WAN IP external network and if I start it the host Web server then the host page is apear that im is not the intention of
  How can I make the Web server of the guest to access other networks operating system?
  in the guest operating system, I can access Web server of the customer by access 192.168.10.201
  but I can't access Web server of the client by typing host operating system access the 192.168.10.201
  any ideas? My version of vmware's vmware-workstation - 6.5.2 for windows

  Hi Teayun,

  Thanks for visiting the site of the community of Microsoft Windows XP. The question you have posted is related to VMware and would be better suited to the VMware or TechNet community. Please visit the link below to find a community that will support what ask you

  http://www.VMware.com/support/
  http://TechNet.Microsoft.com/en-us/default.aspx Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• NAT problem for the Web server

  
  I have configured the new cisco asa 5512. I can't access our Web site from outside. We host our internal site
  This is how I configured. Internal IP of the Web server is 192.168.1.19
  in the following config, I changed my public ip of the webserver to 99.99.99.99
  Can someone help me with this.
   
  the Web server object network
  Home 192.168.1.19
  NAT 99.99.99.99 static (inside, outside)
  NAT (inside, outside) interface static tcp www www service
  outside_access_in tcp allowed access list any object Webserver eq www
  Access-group outside_access_in in interface outside

  It is not open by default, but you already enabled.

  Remember that all you need is a translation you have:

   object network Webserver host 192.168.1.19 nat (inside,outside) static 99.99.99.99

  And the list of access allowing access to desired ports:

   access-list outside_access_in permit tcp any object Webserver eq www access-list outside_access_in permit tcp any object Webserver eq 8080 access-group outside_access_in in interface outside 

• PIX 501 problems with the web server internal.

  I want to open for my internal Web server, so it can be accessed from outside and I read about it here and how to do it and I do what I think of his right, but I can´t operate.

  Now I just tried to open the http port standard 80 but later I want to open a specific port and also use SSL on the web server for added security.

  Then I would like my setup now get help and also how to do when using other ports and SSL later.

  Thanks Thomas!

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  alfta hostname

  domain ciscopix.com

  names of

  name 192.168.1.16 TerminalPC

  name 192.168.3.0 Lager

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 255.255.255.0 Lager

  permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list outside_cryptomap_40 255.255.255.0 255.255.255.0 Lager

  outside_cryptomap_60 ip access list allow

  192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  outside_access_in tcp allowed access list all eq www

  host 62.108.197.90 eq www

  IP outdoor 62.108.197.90 255.255.255.192

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 62.108.197.10 255.255.255.255 outside

  location of PDM 62.108.197.11 255.255.255.255 outside

  location of PDM 192.168.1.0 255.255.255.255 inside

  location of PDM TerminalPC 255.255.255.255 inside

  location of PDM 192.168.2.0 255.255.255.0 outside

  location of PDM Lager 255.255.255.0 outside

  location of PDM 192.168.2.0 255.255.255.0 inside

  location of PDM 62.108.197.137 255.255.255.255 outside

  location of PDM 62.108.197.137 255.255.255.255 inside

  location of PDM 195.67.210.72 255.255.255.255 outside

  location of PDM 62.108.197.90 255.255.255.255 inside

  PDM logging 100 information

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  static (inside, outside) tcp 62.108.197.90 www TerminalPC www netmask 255.255.255.255 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 62.108.197.65 1

  Enable http server

  http 62.108.197.10 255.255.255.255 outside

  http 62.108.197.11 255.255.255.255 outside

  http 195.67.210.72 255.255.255.255 outside

  http 192.168.1.0 255.255.255.0 inside

  http 62.108.197.137 255.255.255.255 inside

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set esp strong - esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  peer set card crypto outside_map 20 195.198.46.88

  outside_map card crypto 20 the transform-set ESP-DES-MD5 value

  outside_map 40 ipsec-isakmp crypto map

  card crypto outside_map 40 correspondence address outside_cryptomap_40

  peer set card crypto outside_map 40 62.108.197.137

  outside_map card crypto 40 the transform-set ESP-DES-MD5 value

  outside_map 60 ipsec-isakmp crypto map

  card crypto outside_map 60 match address outside_cryptomap_60

  peer set card crypto outside_map 60 195.198.46.88

  card crypto outside_map 60 the transform-set ESP-DES-MD5 value

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 62.108.197.137 netmask 255.255.255.255

  ISAKMP key * address 195.198.46.88 netmask 255.255.255.255

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 sha hash

  10 1 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet 192.168.1.0 255.255.255.255 inside

  Get out your ACL - access-list outside_access_in permit tcp any host 62.108.197.90 eq www

  And a new application:

  outside_access_in list access permit tcp any host 62.108.197.90 eq www

  Access-group outside_access_in in interface outside

  * You have the group-access above on your original configuration message, BUT not on the above post.

  Don't forget to issue clear xlate after the change and also record with write mem.

  Try to do this in the pix CLI instead of using PDM.

  Hope this helps and let me know how you go.

  Jay

• Not possible to activate the scripts on the Web server

  Hello

  I would like to create a page .html for Web with a bit of scripting ESP included - Services because now I understand just this:

  <% for (i=0; i<3; i++) {
    ...some text...
   } %>

  According to this document NOR, I first need to enable scripting:

  To use the script with a Web service, you must enable the feature on the Web of LabVIEW server. In LabVIEW, select the script on the Web Server: Configuration page in the dialog box Options to enable the use of scripts on the Web server.

  I activated the Web server and it works OK. But there is nothing called "Scripting" in the configuration page - and the script is executed (the code is just printed in the form of simple text).

  Anyone know how to activate the ESP script?

  Version: LV 2012.

  Best regards, Jan

  Hi Jan,

  In fact, you use the ESP file instead of a static HTML file.  For example, if we had the static html file:

  Hello world

  This file can be located at something like /MyWebService/HelloWorld.html.

  If I then do something like have a page to say "Hello, Jan" or "Hello, Mark" I could use ESP.  In this case, your code might look like:

  <>

  var xname = form ['name'];

  %>

  Hello, @@xname

  The URL of such a web method is perhaps something like jan/MyWebService/Hellovar/Jan where Jan string literal passed to the terminal of a web method that can resemble

  

  In this example, the string "Jan" is passed to the terminal of the value of the VI.  What implementation of the Web method in the spec to build his signature might look like in /Hellovar /: value.

  So, back to your original question.  You embed not ESP breast and the HTML document.  Instead, you embed HTML inside a document of ESP and the rendering of the document in HTML format when accessing the URL of the Web method.  While the paper you mentioned earlier has an example project in that you can use as a reference

• What is the web server integrated for Windows XP Professional?

  Hello

  I would like to know what the web server integrated for Windows XP Professional.

  I don't know of a free web server like Apache or IIS.

  I want to host my site on the net using the web server integrated in XP (not IIS).

  Thanks in advance.

  It is not just any server web, other than IIS, integrated with Windows XP Professional.

  You think perhaps of Personal Web Server (PWS) which was part of the old operating systems like Windows NT.  Which no longer exists in Windows XP Professional - it has been replaced by IIS.

  -B-
  http://www.officeforlawyers.com | http://www.OneNote-tips.com
  Author: Guide to counsel for Microsoft Outlook

• WANT to 114 does not connect to the Web server

  Have installed a 114 WANT, everything works except for the webservices - wireless eprint etc.

  I tried everything-

  1 re-install services - error cannot connect to the web server

  2. Update - error cannot connect to the web server

  3 give the static IP address

  4 restore the default settings

  I have an internet connection on all computers.  Can someone give me a hint on how to get Web services to work?

  Hi sbenzie,

  How your printer is currently connected to the network? Via Ethernet or wireless? What is your current router / network configuration? That shows your printer because it is the IP address? What happens when you try to launch applications?

  Not yet given the information above, here's what I would try.

  I suggest to reconnect the printer to the network by running the Wireless Setup Wizard and attempt to restart the web services. If this is not enough, you may change some DNS settings in printers EWS (built-in web server) to do this, put the IP address in a browser window on your PC.

  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.

  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.

  Now try to connect to Web Services again.

• under vista and it cannot open the Web 192.168.1.1 for linksys router

  I have a Linksys wrt54gl router wireless and I hard wire plugged into my computer so I connected to the internet broadband router. Connections to work because the flashing lights on the front of the router blink correctly.  So I open internet explore and type 192.168.1.1 in the hope that I get the page for the router setting, but instead, I get a message that explore cannot detect the Web site. Wrong address. I get a similar error with Firefox.  The computer was working fine connected directly to the internet bandwidth so sure the internet works. The IP address is set to automatic detection. Someone at - it ideas?

  Hello

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• PIX 501 in the firewall of the Web server

  Hello

  At the suggestion of a colleague, we bought a firewall PIX 501 to protect our new Win2003 web server and a UNIX/Oracle DB server.

  I've never worked with before firewalls.

  Our servers are located in a cage at the ISP and belong to us. There are only two servers providing web site. I have read the documentation in the Getting Started book and it does not answer my question.

  We have 2 web sites with different IP numbers on our web server. Let's say 140.5.5.4 and 140.5.5.5. I understand that I have will redefine the numbers with the firewall (192,...) but I do not understand how the routers at the ISP will be able to route requests for two websites to the firewall when it has one IP number, say 140.5.5.1?

  Any help is appreciated.

  Thank you, Jerry

  Jerry,

  what you are referring is called port forwarding. Whether you a PIX with a public IP address 12.1.1.1 and your web servers are respectively and 12.1.1.2 12.1.1.3. Port forwarding is really a 2 step process:

  * a static translation of the public IP address of the PIX (12.1.1.1) at the address of the web server (12.1.1.2)...

  static (inside, outside) tcp 12.1.1.1 12.1.1.2 www www netmask 255.255.255.255 0 0

  * an intermediate statement basically "all web requests should be allowed in the pix outside of the interface"...

  driving permit tcp host 12.1.1.1 eq www everything

  Here is a link that will help you to clarify this point:

  www.Cisco.com/warp/Customer/707/28.html

  This should help you get started. Regarding the basic configuration, it takes config examples on the Cisco site, if you have access CCO.

  Let me know if it helps.

  Rob H.

• Connect to the Web server

  Just bought a HP Photosmart 7520 installed on Windows 7 Pro and cannot connect to the web server despite having internet connection any ideas

  Hi, sorry to hear that you're having trouble is your new printer connected to the HP web services. Here is a link to a post that covers some possible causes and solutions for connectivity issues. Hope that this help get you connected, but post back if your still having the problem.

  Good luck.

  http://h30434.www3.HP.com/T5/eprint-print-apps-mobile-printing-and-ePrintCenter/eprint-apps-connectivity-troubleshooting-please-review/TD-p/572635