Cannot load a required step of associates module Err :-17600

Similar Questions

• In my report of diagnostic systems that it establishes that there is an error indicating the symptom is "device is not working properly." Windows cannot load the required device drivers. "I don't know what to do.

  Windows cannot load the required device drivers.  It shows the details like Microsoft ISATAP adapter reports "tv_ConfigMgrErr31.  This device won't be available until the problem is resolved.  The Plug-and-Play ID is 17.  What this mean and how can I make the correction of this error and operate?

  Hello

  Control Panel - devices - right click on - UNINSTALL - REBOOT Manager

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you wish
  and on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message
  http://support.Microsoft.com/kb/932520

  Y at - it no devices work not?

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• ISATAP #4 card cannot load drivers

  I just bought a dell studio.  my ISP is at & t with a 2wire506 of the entry door.  In the computer laptop is vista for home and I did a contective wireless and everything went well.  But the 2wire says with connective limited.  I discovered that I can't go on the internet.  system says 'not connected to the internet.  entered management devices, and discovered that the isatap #4 card did not work properly. error 31 (cannot load the required drivers) for this device.  My main hub is a desktop computer (gateway) with windows xp.  I tried to use the local network with a PPPoE connection, but it does not connect unless I plug in the line.  can you please help so I can use internet on the laptop.  and I'm supposed to be private or public wireless.  \
  Thank you
  the scorpion Queen

  Hi Queen of Scorpion,

  In my experience, Microsoft ISATAP with error code 31 is a question can be ignorable. For more information, please see the following article:

  (KB932520) On a Windows Vista-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message

  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; 932520

  In this case, I suspect this problem caused by network adapter missing or damaged. Please first reinstall the driver for your wireless card. Then try to reinstall Microsoft ISATAP by using the following steps:

  1. in the Device Manager, right click on the element of Microsoft ISATAP and choose uninstall.

  2. in Device Manager, click Action, and then select Add legacy hardware.

  3. click Next and select install the hardware that I manually select from the list (advanced user), click Next.

  4. Select network adapters and click Next.

  5. Select Microsoft in the Panel on the left and Microsoft ISATAP Adapter in the right panel.

  6. click Next and complete the remaining wizard.

  Useful article, you can consult:
  http://windowshelp.Microsoft.com/Windows/en-us/help/b3c6477e-1111-4B9F-A52A-fffdc51e9c901033.mspx

  Please let us know if you need additional assistance.

  Kind regards
  Anthony
  Microsoft technical support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• RUNDLL - error loading c:\windows\wrypap.dll - specified module cannot be found, this happens after the windows xp registry.

  RUNDLL - error loading c:\windows\wrypap.dll - specified module cannot be found, this happens after windows xp registry

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.

  If you do not have a good explanation for the name of the file in a Google search, the chances are good that your system is currently or has been infected by malware.

  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.

  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.

  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information
  .  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that you had or have an infection, followed with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• RUNDLL cannot load the lwue.uqo module

  When I start Windows XP roughly halfway through the loading process that a message box appears titled RUNDLL indicating that RUNDLL cannot load the lwue.uqo module can someone tell me what is probably causing this error and what to do about it?

  Hello

  ·        Are you able to boot to the desktop?

  ·        What is the exact error that you are experiencing?

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  Step 1:

  If the problem persists then in safe mode, I suggest you to do a clean boot. Follow the steps mentioned in the article below.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  If the problem started recently, then I suggest you do a system restore to the point when the system worked very well and see if the problem is resolved. Follow the steps mentioned in the article below.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• Norton 360 diagnosis reported: Microsoft ISATAP Adapter #2 is malfunctioning and windows cannot load the drivers required - code 31.

  Original title: ISATAP adapt #2 does not properly. How can I solve this problem?

  My Norton 360 diagnostic report detected a hardware device unusable.  The device type is: Microsoft ISATAP Adapter #2 and the device situation mentions that it is working properly and windows cannot load the drivers required - code 31.

  I think that it is also affecting my internet connection and disrupt its speed.

  Can you please help with this question?

  Thank you very much
  Tony

  Hi Tony,.

  You can try reinstalling the device driver and check if it works.
  Uninstall and reinstall the device in Device Manager.
  a. Click Start, type devmgmt.msc and press to enter.
  b. Locate the Microsoft ISATAP Adapter device
  c. right-click on the device and select uninstall
  d. restart the computer and check.

  You can also consult the following article:

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/default.aspx/KB/932520

  Hope this information is useful.

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• oracle.apps.fnd.framework.OAException: cannot load application module

  Hello

  My custom application ofa was working fine but suddenly he stops and the message below.

  oracle.apps.fnd.framework.OAException: cannot load application module

  Load class: oracle.jbo.common.java2.JDK2ClassLoader

  Charger: oacore.root:0.0.0

  Source code: / dev/u00/r12/apps/apps_st/comn/java/classes /.

  Configuration: < library > in/dev/u00/r12/apps/apps_st/comn/webapps/oacore /.

  at oracle.jbo.common.ampool.ApplicationPoolImpl.doCheckout(ApplicationPoolImpl.java:2002)

  at oracle.jbo.common.ampool.ApplicationPoolImpl.useApplicationModule(ApplicationPoolImpl.java:2793)

  at oracle.jbo.common.ampool.SessionCookieImpl.useApplicationModule(SessionCookieImpl.java:453)

  at oracle.jbo.http.HttpSessionCookieImpl.useApplicationModule (HttpSessionCookieImpl.java

  Don't know what is causing the problem. all the tips are greatly appreciated.

  Thank you

  KK

  Is - the current running in the server or Jdeveloper?

  If it is the server, you did all the changes recently? Did transfer a file? If so, you correctly transfer in binary mode?

  Delete the class files, copy the files again (binary mode if you transfer files class if the java files, transfer in ascii mode and then compile it in the server).

  Bounce the server and see what happens.

  Let us know how it goes.

  See you soon

  AJ

  PS: Please mark the answers useful/correct if it is

• I can not install updates KB973593, KB973704, kb974561, KB975960 I get the error code 646 #! In addition, Microsoft IATAP adapter #5 ROOT\ * ISATAP\0007; #7\0008; 9\0011 # device does not not impossible to load the required driver.

  The program that I have problems with, install my updates, they moved it and I get an error code 646 #. I tried to fallow the guide to fixing the problems to solve the problem though, everything I've read and tried did not work! I have plenty of room for my memory and now I'm stuck! In addition, my adapter from microsoft IATAP #5 Root\ ISATAP\0007; Microsoft IATAP adapter #7 Root\ISATAP\0008 and IATAP microsoft adapter 9 # 0011 Root\ISATAP\ these 3 devices not working properly because windows cannot load the driver for this device, and I don't have a clue on what and how to solve this problem at all. "Were the changes that I made, I started using Mozilla Firefox 3.5.3 for my internet conection and I installed two programs (1) speed of Uniblue SN 2009 and (2) Uniblue Registry Booster 2010 both programs are by Uniblue Systems. CTA Neather program worked as they said that if I uninstslled them and after that there about 2 weeks later I noticed that my updates of the program did not work. , or if these device IATAP drivers worked! I tried the system repair and recovery, which also does not solve the problem. I have a Toshiba Satellite A215 laptop 2.00 GB and my OS is; Microsoft Windows Vista Home Premium, Patch level; Service Pack 2. I'd appreciate any help to fix these problems that I'm having with these programs and drivers, I know just enough about computers to really screw things. Please I need a step by step instruction.

  Thank you

  Keith

  I had to disable the "User Account Control" (UAC), which allows you to run as administrator in Vista.  After that I turned it off, all 4 of these updates installed and it doesn't require manual installation.   Follow these steps:

  In the case of Vista view:

  1.) go to start; Control Panel; "User accounts and family safety"; User accounts.
  2.) click on 'Enable user account control or disable' (last point on the page)
  3.) clear the checkbox "Use User Account Control (UAC) to help protect your computer" and click "OK."
  4.) restart the computer, and then run the installation of the system and they work.

  If you are in Classic view:

  1.) go to start; Control Panel; Security Center
  2 screen.) in the "Windows Security Center", go to the last item "User Account Control" and click the button to turn off.

  You can also see the security shield in your Start menu.  You can also access the UAC via this.

  After that the installation of the system have been updated, make sure that you go back and turn the UAC "" and then restart your computer so that unauthorized updates do not occur.   Always try this turn off if install doesn't work.