Cannot run Canon MP Navigator on Vista Home Premium (32 bit)

Similar Questions

• How to activate the faults COMMITTED to an internal SATA hard drive, but not the other, on Vista Home Premium 32-bit?

  I have a set of 17-inch laptop 2008 which contains two hard drive bays internal, purchased in June.  It came with a single hard drive (traditional spinning disc).  It is running Service Pack 2, Windows Vista Home Premium 32-bit.

  My SATA controller is an Intel 82801GBM/GHM (ICH7-M family); I think it's a first-generation SATA controller (1.5 Gbps).

  I received recently a 160 GB Intel X - 25 M SSD (second generation SATA, but it is fully compatible with the first generation controllers, without additional or jumpers configuration) as a gift from my wife.  I removed my first hard drive completely, installed the SSD in the main Bay and installed Windows, drivers and the Intel SSD utility.  I then reinstalled my HDD original in the second span, completely wiped and reformatted it as a partition; It currently contains my music and other multimedia files.

  The utility Intel SSD tells me I should activate DIPM for my SSD as opposed to HIPM.  This seems to take a bit of tinkering to make Vista, and my situation is further complicated by the presence of my HARD drive (original) secondary, which prefer to use HIPM.

  I read the article on the Microsoft Web site on editing the registry to activate the misconduct, and it's something I would feel comfortable doing. However, I don't want my SSD to use DIPM, my HARD drive is expected to continue to use HIPM, and I was afraid that the proposed fix would allow the misconduct for all readers.

  Could someone let me know how I can activate DIPM for my SSD while continuing to use HIPM to my HARD drive, I'd be very grateful.

  EDIT: My Maintenance of SSD utility said simply that the State of the settings DIPM/HIPM "could not be determined." if Vista automatically selects the correct setting and the SSD utility does not just understand that, which makes my life a lot easier. but it would be nice to know for sure, so I can forget it all (if Vista already defined for me) or change the setting (if Vista did not automatically choose food appropriate for each disk management mode).

  You will need two SATA controllers: both on board or an edge and the other on PCI - E.

  Configure one who does not need TRIM/DIPM (do not use a SSD) as non-AHCI (compatible IDE/ATA-6) in the BIOS and the other (where TRIM/DIPM will be used) as AHCI.

  Connect the drive to which you DIPM AHCI controller. See http://www.abxzone.com/forums/f155/tip-how-enable-dipm-ssds-windows-120968.html for more information.

• I am running Vista Home Premium 32 bit and cannot read the SDHC 4 GB memory card

  I am running Vista Home Premium 32 bit and cannot read the SDHC 4 GB memory card, it worked in Fujitsu siemens but not now. Can anyone help in laymans terms not techno type talk how I can fix it.

  I'm a model so need to step by step instructions: o))

  Hello

  1 have had any changes made on the computer before the show?

  2. do you get an error message? If Yes, what is the full and exact error message?

  Method 1:

  I suggest to test the card by inserting it in a different USB port and later in another computer to test and check if it is detected.

  Method 2:

  I also suggest you to check if the memory card is detected by a different card reader.

  Method 3:

  I suggest you to see link and check if it helps:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

• I have windows vista Home premium 64-bit installed on my sony vaio cs36gj, which was not install updates. Or running fixit is. How updated?

  I have windows vista Home premium 64-bit installed on my sony vaio cs36gj, which was not install updates. \niehter is running thing fixit. How updated?

  Hi Vishal,

  1. what happens when you try to install Windows Update and the fix, you get any error message or error code?

  2 have you made changes on the computer before this problem?

  3 is the limited issue during the installation of specific updates?

  Problem when installing windows update, see the following Microsoft article.

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2: http://support.microsoft.com/kb/2509997

  Solve common installation issues in Windows Update, Microsoft Update and Windows Server Update Services: http://support.microsoft.com/kb/906602

  
  Notes:

  The following steps include changing the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  CHKDSK: Data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.

  Microsoft safety scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again. The data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.

  Keep us informed on the status of the issue.

• Vista Home premium 32-bit. Acer5920. . MIC on all time, cannot find to turn off

  I am running Vista Home Premium 32 bit on Acer 5920. My built-in mic. has constantly and I cannot find how to change it. I only use the microphone. for Skype. To try to resolve the problem, I lost the icon for it and cannot see a plug icon in the microphone. Help, please.

  Hello

  Check the default built-in speakers and check if the problems persists:

  To do it please check the steps mentioned below:

  1. Click Start and click on Control Panel.
  2. click on sound
  3. in the new window, click on the tab 'Read'
  4. now check if the President is in the list and right-click on it and choose activate.
  5. highlight the speaker and click "set as default".

  I hope this helps.

• I have AutoCAD 2002 a 32-bit program cannot install on my Window Vista Home - Premium 64 bit OS. Can someone help me, please?

  I have AutoCAD 2002, a 32-bit program, I can't install it on my computer which has Windows Vista Home - Premium 64 bit OS.
  Can someone help me, please?

  Hi JohnMcLarnon,

  Welcome to the community Microsoft and thanks for posting the question.

  According to the description, it looks like you can not install AutoCAD 2002, he would be grateful if you can answer this question in order to help you further.

  1. what happens when you try to install, summers - get you any error message or error code?

  2 is the issue limited only during installation AutoCAD?

  3. have you made changes on the computer before this problem?

  I suggest you to see the steps in the following Microsoft article and check if it helps.

  Solve problems with programs that cannot be installed or uninstalled: http://support.microsoft.com/mats/Program_Install_and_Uninstall?wa=wsignin1.0

  Troubleshoot installing or uninstalling programs: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-installing-or-uninstalling-programs

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  If you have any other questions or you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• I lost my BIOS password, how can I recover or change the password. I am running vista Home premium 64-bit

  I lost my password to access the bios and set up the screen. How to retrieve or change the password. I am running vista Home premium 64-bit.

  original title: I lost my password

  I lost my password to access the bios and set up the screen. How to retrieve or change the password. I am running vista Home premium 64-bit.

  Buna,

  We are forbidden to help you with the lost BIOS passwords. Contact the manufacturer.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/keeping-passwords-secure-Microsoft-policy-on/a5839e41-b80e-48c9-9d46-414bc8a8d9d4

  About questions about hardware BIOS password reset, we ask that you direct customers to the appropriate resources on the sites of manufacturers of equipment for the correct procedure.

  Please help us to ensure the safety of our community.

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  The Revedere

• Cannot access my IOGEAR BOSS with Vista home premium

  I have problems to access the directories on my external device with my new PC, and I hope you can help me.

  I just replaced my old HP Desktop running XP OS with a new DELL desktop which is under Vista Home Premium (32 bit) and now I can't access the device of utility of IOGEAR BOSS. I was able to access the external device with it and can be accessed with 2 other PC at home now. Can't seem to connect to the external device with this new system.

  What I can do:
  I am directly connected the BOSS and can access the internet via the BOSS. I also see the external device in my network. I can ping, tracert it. That's where! Just can't log in there!

  What I can't do
  Map a drive to the external device or authenticate in the unit. (When I try to access it, it prompts me for the ID/PW as it should, but he does not like the ID/PW I provided). I know that the PW & ID works calibrated it works on 2 other PC's connected on it.

  Steps to access the external device
  I am trying to access by taking the following measures:
  1 map a network drive
  2 assign the letter Z
  3 path: \\192.168.2.1\share
  4 pushes. me for ID & PW - admin\ *.
  5 ERROR Message: Logon FAILURE - NOTES: now shows the ID: Desktop\admin

  What I've done
  1 Contcted IOGEAR - checked all the settings of security, network and pwermission and reset the permissions of the external device to the original state. Did not work. They sent me to Ms & Dell.
  2. contacted Dell - did the same exact steps. They sent me Ms.

  Can anyone help?

  According to the site Web of IOGEAR (http://www.iogear.com/product/GNS1000/) it is only compatible with Windows® 98SE, 2000, ME, XP.  So so looking for a compatibility issue.  The update of the firmware is from March 2006, you might want to update the Firmware and see if that helps, but with compatibility issues, it's a scenario 'best effort '.

  Below you will find the IOGEAR support page, I hope that helps solve your problem.

  http://atenpbsr2.ATEN-USA.NET:8000/Inet_tech/form/us/index.asp

  Stephen Davies MS

• Recent problem with very slow internet browsing on all browsers Windows Vista Home Premium 32 bit

  Separated from this thread.

  Hi all I'm having the same issues as Theresa in the thread above split. I have Vista Home Premium 32 bit service Pack 2 with all the installed updates (automatically done!).  Within 3 months, this PC at home that was formerly an excellent navigation device became very slow when you browse using IE, Firefox or Chrome. It takes 30 to 50 seconds to load any web page (Yahoo, eBay, etc.). I followed all the instructions suggested to Theresa in SafeMode by Bill Smithers. Resulted in nothing other than a few cookies and Wetherbug I killed. I also run McAfee total protection and Spybot S & D every 3 days with nothing found.

  I have reset my browsers to the specifications of the factory without change.

  Comcast is my internet provider high speed and my speedtest returns 65 - 75 MB/s download and 11 Mbit/s upload very regularly. I connect directly to the bridge. I had Comcast out and they swapped unity Arris of a unit of Cisco beefier but that changes nothing. Other devices on my network domestic perform very well and do not have this problem.

  When I browse a site the CPU spikes up to 88% use in 45 seconds and is stable at 50% usage 1.7 GB memory.

  The only thing I can infer is at this time that something happened to the operating system during automatic updates or some other setting has been changed.  I could use any help or suggestions you may have! Otherwise, I love this OS and have not had any problems. Thanks, Dhoffa

  Tune Up

  Internet Explorer

   

  To improve performance for IE, you can reset internet Explorer to the factory settings. This will disable memory addons chewing and bar tools, etc. that you've installed over time.

  In Internet Explorer click on Tools in the bar and then Internet Optionscommand. Go to the Advanced tab, and then click the Reset button.
   
   
  Or disable/remove specific ones, in Internet Explorer click on Tools for button on the command bar - Manage the Addons - enable or disable Addons - select the addin - Remove or disable the button.
   
   
  There's a Fixit
   

  Troubleshoot Internet Explorer to IE quick, safe and stable

  http://support.Microsoft.com/mats/ie_performance_and_safety/en-us

   

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

   
  Other memory hogs
   
   
  You probably many useless auto startup programs. You can disable these programs.
   
   
  Click Start - all programs - Accessories - run and type
   

  msconfig
  

   
  Then go to the Startup tab uncheck the things you don't need.
   
  Use the command line column to find info on the file, if it does not use display menu - Select the columnsdisplay. Use the name of the folder that contains the file and right click - Properties - Details tab to see what it is.
   

  Explorer

  Explorer (explorer.exe) is the program that is the start menu and taskbar, windows folder and the office (which is a folder window).

  The Explorer is built on addin programs called Extensions of Shell. The standard is provided by Microsoft, but programs add their own.

   
  • Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx
  • Close the windows explore
  • Start Autoruns by right-clicking and choose Run as administrator
  • Click on the Options menu - entries and Filter Options to hide Microsoft tick and clear to understand empty slots
  • Go to the explore tab and uncheck everything to the left.
  • Reset
   

  Difficulty of the Windows system to the performance issues on Windows computers slow Fixit

  Automatically troubleshoot and fix problems of Windows performance. Enhance, optimize and speed up Windows computers and make slow PC faster.

   

  http://support.Microsoft.com/mats/slow_windows_performance/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  --

• Blue Screen at shutdown - STOP: 0x0000 008F (Vista Home Premium 32-bit)

  Whenever I stop, I get a blue screen of death.  I had not used my computer for a few months, so I do not remember if the hardware or software has been added.

  I put the BSOD to stop so I could write the codes - I googled them came but with nothing.

  Here is what says the BSOD:
  STOP: 0x0000 008F (0 x 0005 C000, 0 x C4E3, 0 x AC2E DC0C, 0 x 0000 0000 8261)

  My system runs Vista Home Premium (32 bit) on a bridge 5442 with 4 GB of Ram and an Intel Core 2 CPU 4400 running 2.00 Ghz

  Any help or advice is most appreciated.

  Thank you kindly!
  Marilyn P

  Hello

  Two main causes of this blue screen video drivers and BIOS - check with system manufacturer site for
  View of the adapter (video) and BIOS, then on site of the manufacturer of the device for the last video. There may be other drivers
  in order to check there. DISABLE the auto-pilot plant as those who are older and if updates Windows suggests
  a pilot just HIDE. Antivirus is another possibility.

  See methods of update driver generic in the next message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved .chk , which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  It comes to my convenience store generic bluescreen:

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps and happy holidays!

  Rob - bicycle - Mark Twain said it is good.

• Vista Home Premium 64-bit system file dllhost.exe is missing.

  System file dllhost.exe is missing.  sfc/scannow could not repair/replace it.  How can I get a new copy of the file dllhost.exe for Vista Home Premium 64-bit (for an AMD64 machine)? Thank you.

  This is an extract from the log after running sfc:

  00000861 [SR] cannot repair the military record [l:22 {11}] "dllhost.exe" Microsoft-Windows-COM-mother surrogate, Version 6.0.6000.16386, pA = PROCESSOR_ARCHITECTURE_AMD64 = (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, type neutral, TypeName neutral, neutral public key in the store, file is missing "
  2010-11-16 10:40:53, info CSI 00000862 [SR] this element is referenced by [ml:38 {19}, l:36 {18}] "Windows Foundation.
  2010-11-16 10:40:53, info CSI 00000863 [SR] could not reproject corrupted file [ml:520 {260}, l:46 {23}] '------? \C:\Windows\System32"\[l:22{11}]"Dllhost.exe '; source file in the store is also corrupted

  System file dllhost.exe is missing.  sfc/scannow could not repair/replace it.  How can I get a new copy of the file dllhost.exe for Vista Home Premium 64-bit (for an AMD64 machine)? Thank you.

  Extract the exe of your Windows DVD:

  http://blog.NirSoft.NET/2009/09/17/how-to-extract-missing-system-files-from-the-DVD-of-Windows-7vista/

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• How to activate the plug ins for WPM 11 on Windows Vista Home Premium 32 bit OS? __

  Cannot read dvd OMP. DVD will not auto play and got an error msg stating that the plug-ins have been disabled.  How to activate the plug ins?  I can't reinstall/repair WPM 11 under Vista.  I tried to update without success.  I ran sfc / scannow and there are no errors, found no errors or corrupted files.  Please indicate how do 11 WPM version 11.6002.18065 not work on my Vista Home Premium 32 bit OS! plug-ins have been disabled in 11 OMP

  I have installed a codec pack k - lite with no luck!

  Hi kikstart2,
   
  For the CD/DVD drive problem, try the following steps.
  1. visit the following Web site, click the "Run now" button and follow the instructions in the wizard to run the tool: http://support.microsoft.com/gp/cd_dvd_drive_problems
  2. once the tool is running, restart the computer.
  3. Insert the CD / DVD and check if it works very well.
   
  NOTE: There is no option to repair/reinstall Windows Media Player on Windows Vista.
   
  If the problem persists, restore the computer to an earlier time when everything worked well. To do this, try the following steps.
  1. Click Start, type system restore in the search box and press ENTER.
  If you are prompted for an administrator password or for confirmation, type the password, or click on continue.
  2. click on choose a different restore point and then click Next.
  3. click on a date on which the issue moved not.
  4. click on next.
  5. click on finish.
  6. check if everything works well.
   
  For more information see what is system restore?
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Windows Vista Home Premium 32 Bit > Windows 7 Home Premium 64-Bit?

  Just a question, I currently have Vista Home Premium 32 Bit OEM and want to upgrade to Windows 7 64 bit.  When you buy an upgrade pack does with Versions 32 and 64 BIT, I understand not doing a clean install, etc..  but the DVD with this capability upgrade?  as far as I can see the comments are widespread, and State if the disk used for the upgrade is a full version or an upgrade copy.   Because I would rather buy the upgrade on a whole new pack of detail for reasons of $.

  Yes, this full and updated details to level version boxed packages include records of 32 and 64-bit.

  Upgrade paths:
  When important changes to your computer, for example an upgrade, it is always recommended that you back up your system before installing a new version of Windows. In your case, you can upgrade to Windows 7 depending on the edition and the architecture of Windows Vista, you have installed. If you are running a 32-bit version of Vista and upgrade to a 64-bit (Windows 7 edition) version, you'll have a pure make install, it is the opposite case.

  If you are using Windows Vista Home Basic or Premium consumer editions, you can only upgrade to Windows 7 Home Premium or Ultimate. Also, you can make the downgrades, which means, if you are running Windows Vista Ultimate Edition now, you cannot downgrade to Windows 7 Home Premium. You perform logical upgrades:

  Windows Vista Home Basic > Windows 7 Home Basic, Premium or Ultimate
  Windows Vista Edition Home Premium > Windows 7 Home Premium or Ultimate
  Windows Vista Business > Windows 7 Professional, enterprise or ultimate edition
  Windows Vista Business > Windows 7 Enterprise
  Windows Vista Ultimate > Windows 7 Ultimate.

  Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Can I switch from Vista Home Premium 32 bit to Windows 7 Professional 64-bit?

  I wanted to basically triple - check the compatibility of my laptop current in what concerns the upgrade from Vista to Windows 7.

  As a student, I can get windows 7 professional 64 bit for £30. Their moment I'm running a 32-bit version of vista Home premium, and I wanted to confirm my laptop is up to running a 64-bit operating system, and that the upgrade from a 32-bit version of Vista to a 64-bit Windows 7 version is also possible.

  I ran the Windows 7 Upgrade Advisor, and it is said that everything should be correct regarding my hardware specifications.

  The results of the 64-bit Upgrade Advisor version:

  -"Your graphics card supports Aero de Windows interface.
  -Processor: 2.1 GHz
  -3.0 GB of RAM (I know it's 4 GB but 32-bit vista can not handle the truth)
  -80.7 GB free on C:

  The consultant warn me that I'll have to do a clean install, rather than an upgrade. I'm not worried about it, I can back up my files to an external hard drive.

  What I want to know is, I will certainly be able to upgrade Vista Home Premium 32 bit to Windows 7 Professional 64-bit, with the upgrade kit here http://store.digitalriver.com/servlet/ControllerServlet?Action=DisplayHomePage&Locale=en_GB&SiteID=msshgb at the bottom of the page?

  Thanks for your help.

  You will need to do a clean install, there is no place on the way to upgrade Windows 7 32 bit to 64 bit.

  Using the disk of 64-bit Windows 7, install Windows 7 Windows Easy Transfer Utility from the DVD (to find it, simply navigate to x:\support\migwiz, "x:" is the name of your hard drive. (In this case, you will see a collection of files, the important"that you must search for and double-click is 'migsetup'.) run it and create a DAMP (Windows Easy Transfer file), if you have an external hard drive, you can access it later when you perform a clean install of Windows 7 64-bit disk so you can stored there.

  Once you have done this, just do a clean install of Windows 7 64 bit disc. In Windows 7 64 bit disk, start Windows Easy Transfer, follow the wizard screen, tap on which is stored the WET file (external hard drive) and it will restore your personal files and settings. Reinstall the applications needed.

  http://www.notebooks.com/2009/10/07/using-Windows-easy-transfer-in-Windows-7/

  Upgrade paths:
  When important changes to your computer, for example an upgrade, it is always recommended that you back up your system before installing a new version of Windows. In your case, you can upgrade to Windows 7 depending on the edition and the architecture of Windows Vista, you have installed. If you are running a 32-bit version of Vista and upgrade to a 64-bit (Windows 7 edition) version, you'll have a pure make install, it is the opposite case.

  If you are using Windows Vista Home Basic or Premium consumer editions, you can only upgrade to Windows 7 Home Premium or Ultimate. Also, you can make the downgrades, which means, if you are running Windows Vista Ultimate Edition now, you cannot downgrade to Windows 7 Home Premium. You perform logical upgrades:

  Windows Vista Home Basic > Windows 7 Home Basic, Premium or Ultimate
  Windows Vista Edition Home Premium > Windows 7 Home Premium or Ultimate
  Windows Vista Business > Windows 7 Professional, enterprise or ultimate edition
  Windows Vista Business > Windows 7 Enterprise
  Windows Vista Ultimate > Windows 7 Ultimate. Andre Da Costa http://adacosta.spaces.live.com http://www.activewin.com

• Firefox 4.0 is now compatible with the browser ZoneAlarm 1.5.260.0 and Windows Vista Home Premium, 64-bit Service Pack 2 system?

  Firefox 4.0 is now compatible with the browser ZoneAlarm 1.5.260.0 and Windows Vista Home Premium, 64-bit Service Pack 2 system? Earlier when checking for updates it had compatibility problems. These issues have been resolved for me operation secure with Firefox 4.0?

  According to the guru on the ZoneAlarm user forum, Firefox 4 and other new browsers won't be compatible with the new version of ZoneAlarm, releasing. See:

  • http://forums.zonelabs.com/showthread.php?t=76985 & highlight = Firefox

  "You must update the following plugin:

  • Adobe PDF plugin for Firefox and Netscape 8.2.6
  1. Check your plugin versions on one of the following links:
     • http://www.Mozilla.com/en-us/pluginCheck/
     • https://www-trunk.stage.Mozilla.com/en-us/pluginCheck/
     • Note: plugin check page lacks information about all versions of the plugin
  2. Update of Adobe Reader (PDF plugin):
     • Within your existing Adobe (If you have already installed) drive:
       • Open the Adobe Reader program in your list of programs
       • Click Help > check for updates
       • Follow the instructions to update
       • If this method works for you, go to the section "download full installer ' below and go to"after the installation"below
     • Download the full installer (If you have NOT installed Adobe Reader):
       • SAVE the installer to your hard drive (save to your desktop so that you can find it after downloading). Exit/close Firefox. Run the Setup program that you have just downloaded.
       • Use one of the links below:
         • https://support.Mozilla.com/en-us/KB/using+the+Adobe+Reader+plugin+with+Firefox (click on "Install and update of Adobe Reader")
         • See also the download link': http://get.adobe.com/reader/otherversions/
     • After installation, launch Firefox and recheck your version.