Cannot uninstall legacy NOR-488. 2

Similar Questions

• Uninstall the NOR 488.2

  How can I uninstall the 488.2 OR...?, I do not find it on remove/uninstall program in WIN7.

  IT IS TOO EASY... JUST GO TO CONTROL PANEL / UNINSTALL A PROGRAM / NATIONAL INSTRUMENTS PROGRAMMS / DOUBLE CLICK AND CHOOSE OR 488 TO REMOVE... RESTART AND COMPETE WITH THE UNSTALLATION... TOO EASY

  Thank you

• Installation of NI-VISA and NOR-488. 2 on Mac

  I have a new Mac on which I am trying to install instrumentation OR (VISA and GPIB) pilots, and things don't work any tips would be appreciated. I downloaded the most recent version of these two (14.0 visa) and 3.0.1 for the GPIB, ran the installers (restart the computer between the two installed) and then tried to run the VISA configuration utility and the GPIB configuration utility to verify that the drivers were ok (at this point, no measuring equipment is attached to the machine (ultimately, the material will be a USB-> RS232 adapter and a USB-> adapter GPIB).

  The two configuration utilities crashed running. Config GPIB obtained in what concerns to the top of its window and then crashed a few seconds later; NI-VISA never even managed to finish to display the home screen.

  In reviewing reports of incidents, accidents seem to be in the OR-PAL driver at low altitude. The report indicates that

  / Library/Frameworks/nipalu. Framework/versions/1/nipalu

  Abort() called

  Poking around the list of files mentioned in the uninstall NOR-PAL guide, it seems that the kernel extension nipalk.kekt was not actually installed correctly (it is absent of/Library/Extensions and/System/Library/Extensions, and according to the uninstall folder, it should be present in both. I tried to copy the kext above a machine that does not have a functioning VISA/GPIB install, but OSX refused to load because it has not actually been installed.

  My plan right now is follow the uninstaller for VISA, GPIB and NOR-PAL and then try to run the installers, but I fear that I will end up in the same place. Y at - it something special or something needed to get these drivers to install correctly (i.e. should things be installed in a specific order, should I try to install VISA 5.4 and then do an upgrade installation 14, try to sacrifice a goat, stuff like that)?

  The material is a Mini Mac OSX 10.9.5 running.

  Thanks for any help.

  And just to follow up with a few additional details, I went through the same procedure on a second Mac that was fresh out of the box. When running Setup for NOR-488, one of the things that we tried to install was an "Update" the subsystem NI Core Services of pilots. This was despite the fact that the VISA facility has implemented a much newer version of the kernel drivers.

  Thus, it seems that the problem is that NEITHER-488 Setup does not correct version control before overwriting the subsystem of pilots. He obviously checked that the driver has been installed, since the action has been listed as "update" instead of "install".  At least in principle, running the installer of NOR-488 first, then the VISA installer should work, but for some reason some the only time where I tried in my tests, it did not work. Maybe, I haven't had a full work of sanitation among other failed attempts. Just for the record, is the sequence that seems to work

  (0) remove all traces of any agreement, failed to install. Follow the steps described in the files uninstall.txt for NOR-488. 2, NI-VISA and NOR-PAL. The uninstall for this latter guide is located in/Library/Application Support / National Instruments/NOR-PAL

  (1) perform a standard installation of NI-VISA 14.0. Restart the computer. Check VISA works (just run the config utility)

  (2) perform a standard installation of NOR-488. 2 3.0.1. Restart the computer. The VISA and GPIB crash when access

  (Optional) curse (2A) to the length

  (3) perform a standard installation of NI-VISA 14.0. Restart the computer. The VISA and GPIB should now be functional.

  Tested on a pair of 'Late 2012' Mac mini OSX 10.9.4 running. One machine was Labview 2014 before you install the drivers for the instrumentation, the other had not installed LabVIEW.

• Problem installing NOR-488. 2 for windows 7

  Facing some installation issues that need your support.

  Tried to install NOR-488. 2 for windows 7 and there is a window

  pop up. See attachment.

  CAN advice there at - it a patch of window to fix this?

  Thank you

  Mike.T

  Managed to solve the problem.

  I have uninstall all programs of NOR (Please make sure that all traces of programs OR is deleted).

  Website below can help guide by removing all programs of NOR.

  http://digital.NI.com/public.nsf/allkb/B4BF3B96988453B98625728100009670

  Then I proceed to the installation of the last worm NOR-488. 2 3.1, followed by the installation of the hardware (card GPIB).

  Finally the Labview 7.1.

  Now test to see if my old labview software and hardware can operate smoothly in windows 7...

  Thanks for the support!

• Device driver Upgrde-NOR-488. 2

  I am running NI 2.73 device driver on my Windows 7 system.  I want to update the device to the most recent driver and more great NOR-488. 2 (I think version 3.0.2).  I can just install the new device driver or do I need to uninstall the old stuff OR first?

  Thanks, Mike

  Done and done.  I wasn't sure if there was a setting to MAX to do.  Thanks for your help.  We will examine this topic 'closed '.

• I can't uninstall two extensions. I tried the troubleshooting tips given in "Cannot uninstall an add-on" but that did not help. Maybe because I have 4.1 and it is for 3.5/3.6. I disabled the but I'd rather not have it on my computer.

  I went through the steps on 'cannot uninstall an add-on. " Uninstall in safe mode doesn't seem to work and when I try to uninstall it manually, I'm either wrong, or that the information does not apply to 4.1 because I don't see anything in the folder that contains that matches the ID in the extension folder.

  I also tried to look in the folder of installation of firefox and uninstall from the Control Panel, but no luck there.

  Any help would be greatly appreciated

  For InternetEngine - feed Applications. see:

  • http://forums.techguy.org/all-other-software/995275-solved-message-webpage-2-a.html

  Control Panel > programs and features - disable or uninstall Internet engine

• NOR-488. 2 missing

  Hello

  I made a kit of distribution for one of my programs, but then decided to add on the program. When I went to build another distribution kit, Labwindows stops halfway through and said that NEITHER-488. 2 could not be found in the directory and insert the Labwindows DVD driver. After that I inserted the disc, it still can't find the NOR-488. 2. This has happened on two separate computers with installed Labwindows. What can I do to get this driver?

  
  

• error 7 GPIB / NOR-488

  Ladies and gentlemen,

  I am trying to contact a Keithley SMU 236 on Labview 2009 running on Windows XP.

  Write orders by VISA works very well, but written with functions GPIB does not work. I got following error messages:

  7 Fehler ist bei GPIB: Schreiben in GPIB_TEST.vi aufgetreten

  G is:

  LabVIEW: Datei nicht found. Die Datei wurde possibly is Debby, oder der path please angegeben ist oder. Use Sie zum example unter Windows als Pfadseparator einen umgekehrten Schragstrich (\), Mac OS of unter einen colon ( und unter Linux einen Schragstrich (/).) ME Sie based BACK-Eingabefensters Datei oder die Richtigkeit the Pfads explorers.
  =========================
  NOR-488: GPIB-Schnittstelle existiert nicht.

  Since it is the German here is a summarized translation:

  error 7 in GPIB:WRITE in GPIB_Test.vi

  possible reasons:

  LABVIEW: File not found.

  [..]

  NOR-488: GPIB Interface does not exist.

  ----------------------------------------------

  The program is attached.

  Thx for your help!

  NOR does not sell Agilent GPIB boards. It's like Microsoft, selling Apple products. In order to use a Board of Agilent GPIB, you need to use VISA. In addition, read this:

  http://digital.NI.com/public.nsf/allkb/3B3626D9C1F999218625694200791AD7?OpenDocument

• Connection problem-NOR-488 GPIB: connection to the driver or device error

  Hello

  I am trying to connect with my tunable laser "Santec" by GPIB-USB-HS. I received the file VI Labview (instrument driver) for my model of tunable laser STL-210 http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=2791 . When I run any VI, for example the "laser_on_off.vi" file I received the error message "NOR-488: connection to the driver or a device error. I checked the 'measurement and automation explorer' and Communicator of NOR-488. 2 gives me the following message appears when I send "interrogate" send string * IDN?

  ----------------

  It is meaningless.

  You have to step way back. The Setup instructions for the GPIB-USB-HS shows you first run diagnostics. Finally, you have done this and got a failure. That's why you get "NOR-488: connection to the driver or a device error. Until the diagnostics pass, you lose everything just your time with anything else. Please provide details on the failure when you run the diagnostic tests.

• LV 2016: LabVIEW could not create the required channel file permission error endpoint; NOR-488: Error of hardware detected DMA

  I just installed the new 2016 LabVIEW with the two patches and wanted to check the new feature.

  When you create a channel writer, there was a pop up select the Channel end point, but whatever the option chosen, there is a window saying "LabVIEW could not create the required channel endpoint", error ccode: 8 file authorization error

  NOR-488: Error detected DMA hardware.

  I have error permition from file to file, file that is?

  By chance, do you have re-defined the default data directory in LabVIEW?  LabVIEW uses to host files for the warp threads, and if you moved from its default position in your profile (C:\Users\\Documents\LabVIEW data), especially if you moved it to the root of C:, it could become unalterable.  This must remain in your profile!

  Bob Schor

• NOR-488: The non-existent GPIB interface. During the generation of the Application in LV8.5

  Joined a vi that I'm building in an exe file.  It contains a single CONDUIT, but whenever I try to build it I get the following error...

  -----------------------------
  Error 7 is is produced to invoke the node in AB_EXE.lvclass:Build.vi-> AB_Build.lvclass:Build_from_Wizard.vi-> AB_UI_FRAMEWORK.vi-> AB_Item_OnDoProperties.vi-> AB_Item_OnDoProperties.vi.ProxyCaller

  Possible reasons:

  LabVIEW: File not found. The file may have been moved or deleted, or the path to the file would be incorrectly formatted for the operating system. For example, use- as Windows path separators: on Mac OS, and Linux. Check that the path is correct using the command prompt or file Explorer.
  =========================
  NOR-488: The non-existent GPIB interface.

  Name of the method: Build: Application
  -------------------------------

  I saw other people with this problem, and I tried their solutions.  I have quit labview, created a new project, new vi... no luck.  I can build on another box, but not mine.  He points to a configuration problem, but I can't.  Any suggestions?

  I just thought of it... While trying to think of everything that was different from when he worked in now... I realized that I turned off my firewall during installation!  I checked off and now the application will build.

  Thanks for the help of the crows Fan and I gave a congratulations for your post on the builder application error codes.

• get an uninstalled program which will not uninstall when I try it says it is the file is absent and cannot uninstall

  I have a particular program I am wanting to uninstall and I repeatedly get an error message indicates file is absent and cannot uninstall and I went through trying thing Manager uninstaller utility, and when it gives me the list of programs it is not, then it gives the option to type in the code of the file or something Well I don't have because he says that's not on my computer anywhere, but I can't always get rid of the program.
  Help!

  It's a Windows Vista Dell, not sure what the other computer details

  Hello

  1. what program you want to uninstall?

  2 are you able to uninstall any program?

  3. were there any changes made to the computer before the show?

  Please run the Microsoft fixit from the link below.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

• Cannot uninstall a program. HKEY unaccessable

  Cannot uninstall a program. Error message says not able to open H_Key_Local_Machine 32 / Windows/Current Version/Shared DLLs.

  Hello

  It is always helpful if you give the name of the program you want to uninstall

  the manufacturer of the program may have an uninstall tool or a special method to uninstall

  Try this free version of the program revouninstaller

  http://www.revouninstaller.com/revo_uninstaller_free_download.html

• I can not using F8 safe mode, so I can not get access to my admin account and therefore cannot uninstall my program

  original title: administrator, f8 safe mode access

  My computer problem begins with not being about to uninstall a program. I need administrator permissions. I am the administrator with a password. I'm not invited to give a. Nothng happens when I press a button with a shield on it. I received another message that tells me "unable to open the access control editor: the system cannot find the specified file. I found the instructions online to restart the computer (by pressing the F8 key) in safe mode. Once in safe mode I can essentially take possession of the C drive and reset admin ACCT. in SUMMARY, I can't have with using F8 safe mode (I tried once bagillion) so I can not get access to my admin account and therefore cannot uninstall my program. Can anyone help?

  I don't know anything about "reset admin account" but here are two things that may help the case to start in safe mode.  First, enter the mode safe mode with f8 key is a matter of time.  On my computer (Dell) during the boot process, I'm going to get a screen send me options of start of f2 and f12, which is to enter the BIOS.  I can start hitting key f8 then but you will in safe mode unless I'm hit immediately after that the screen with f2 & f12 choices goes.  I just hit several times for a few moments at this time.

  If this does not work for you, here's another possibility: http://www.howtogeek.com/howto/windows-vista/force-windows-to-boot-into-safe-mode-without-using-the-f8-key/

• Error 16, corrupted files cannot uninstall/reinstall

  I recently downloaded creative cloud and Flash Professional CC of the trial. Then trying to open Flash I got an error 16. So stupidly, I deleted the files manually thinking I could reinstall just by using creative cloud. However now creative cloud always think installed sound and is unable to uninstall it. I tried to restore the files, but still have error 16 and cannot uninstall by using creative cloud. so I don't know what to do. I also used Creative cloud cleanser but it does not work, after you have reinstalled creative cloud he always thinks its installed and will not let me uninstall it.

  
  

  This is a re-post because the Member of staff who responded to her did not respond when his advice did not work.
  

  Please try: Configuration error. CC, CS. I hope this helps.