Cannot VPN in the network through PIX501

Similar Questions

• Comments Win XP cannot connect to the network when Cisco VPN works on Mac

  Guest OS (Win XP) on the merger connects to the network, no problem. However, when I start a Cisco VPN on my Mac (not in the guest operating system) and then start Fusion/guest OS, the guest cannot connect to the network.

  I was able to use this configuration for a year on an old MacBook Pro (unibody). Last month, I got a new MacBook Pro and flying over my virtual machine image. I don't check for a few weeks. I'm sure I fly over the image correctly because everything else seems OK or if the IT guys doing something to block my traffic over the VPN.

  Config

  -Fusion - Version 3.1.0 (261 058)

  -Mac - 10.6.4

  So far, I have tried the following

  -started to merge and XP without VPN on Mac - OK (bridge autodetect)

  -launched VPN to work, and then launched Fusion - no network

  -tried ipconfig/release, ipconfig / renew - not always no network

  -tried NAT - do always no network

  Thanks in advance. For any help or suggestion will be greatly appreciated.

  Bernie

  The NAT value and then restart the virtual machine.  Works for me with the VPN client built into a cisco router.

  Do not work the real on 10.6.4 cisco software unless you really need to.

• "Cannot connect to the network." When you enter the correct password for wireless network

  Hello

  I have the HP Photosmart C7200 all-in-One series.

  This seems relatively insignificant compared to some of the problems posted here, but nevertheless it is a problem.  I have a Verizon FiOS (Actiontec) router.  I am trying to connect to it wireless; the network key is using WPA authentication.  I followed all the instructions in the quick start guide.

  My printer detects my network and application authentication key.  I enter the correct key, the printer is trying to establish a connection, but after about 15 to 25 seconds, I get the error message, "cannot connect to the network.  I know that my key is correct; I connect to my router very well through several laptops, PDA, etc.  I have reset the settings network default manufacturer and tried without success.

  I don't know what kind of trouble shooting I'm supposed to do here.  The printer detects the router (albeit low signal strength) whenever I try to connect, I enter the password each time and I get the error each time.

  Your help is greatly appreciated.

  Edit: I printed the test report wireless network, here are the results:

  Radio on   PASS

  The radio work   PASS

  Ethernet cable not plugged in   PASS

  Network name (SSID found)   PASS

  Security   PASS

  The printer settings compatible with the configuration of the wireless router   PASS

  No filtering   IN CASE OF FAILURE

  Connected   Not work

  The signal strength   Very low

  Other networks detected matching you the network name (SSID)   NO.

  I know this sounds strange, but try changing channel by channel 11 of the wireless router.

• I want to send the .ps file to the network through the on-board system postscript printer.

  I use the HP LaserJet 5100 printer.

  I want to send the .ps file to the network through the on-board system postscript printer (the ARM Cortex microcontroller is used and the TCP/IP stack is worn).

  I am able to send the file .ps for postscript using the windows system network printer and the file goes to the printer.

  When the .ps file is sent to the printer by using the command line: copy test.ps\\printer_server\printer_port, is the driver is come into picture.

  Please help me.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Cannot save via the speaker through programs such as Audacity. Solvable?

  Cannot save via the speaker through programs like Audacity without horrible sound quality. Solvable?

  Hello

  • What happens when you try to save through the loudspeaker?
  • You receive an error message?
  • If it works well before?
  • What were the changes made before the issue started?
  • You are able to register normally?
  As you can not record with audacity, the problem seems to be related to the audacity.
  I suggest you to contact the support of Audacity for assistance on the issue. See the help link - below

  http://Audacity.sourceforge.NET/contact/

• [Issue] Is it possible to change the order of connection of the network through the powershell command or back?

  Hello my dear

  I would like to ask how to change the binding of the network through the powershell command or back order.

  I know it could be changed as below.

  http://Windows.Microsoft.com/en-GB/Windows/change-network-protocol-bindings-order#1TC=Windows-7

  but I want to change it via text command. Because sometimes, I change it many servers via GUI and then happened a long time depending on the amount of servers.

  If it can be modified it using the command text, or registry, it will be useful for me.

  Thank you.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  http://social.technet.Microsoft.com/forums/en-us/home
  http://social.msdn.Microsoft.com/forums/en-us/home

• PIX501 customer VPN - cannot access inside the network with VPN Session

  What follows is based on the config on the attached link:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

  PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

  We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

  Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

  We have the same problem with the customer 4.0.3(c)

  Thanks in advance for any help!

  =======================================

  AKCPIX00 # sh run

  : Saved

  :

  6.2 (3) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname AKCPIX00

  domain.com domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  fixup protocol sip udp 5060

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  external IP address #. #. #. # 255.255.240.0

  IP address inside 192.168.1.5 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool akcpool 10.0.0.1 - 10.0.0.10

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address akcpool pool akcgroup

  vpngroup dns 192.168.1.10 Server akcgroup

  vpngroup akcgroup by default-domain domain.com

  vpngroup split tunnel 101 akcgroup

  vpngroup idle 1800 akcgroup-time

  vpngroup password akcgroup *.

  vpngroup idle 1800 akc-time

  Telnet timeout 5

  SSH #. #. #. # 255.255.255.255 outside

  SSH timeout 15

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd dns 192.168.1.10

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  AKCPIX00 #.

  Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

  mymap outside crypto map interface

  ISAKMP allows outside

  Enter these two commands should be enough to reset the ipsec and isakmp.

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x

  Hello

  I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside.

  If anyone can share some light... There's got to be something escapes me...

  Here's my sh run

  Thank you

  Raul

  -------------------------------------------------------------------------------

  DLSYD - ASA # sh run

  : Saved
  :
  ASA 9.1 Version 2
  !
  hostname DLSYD - ASA
  domain delo.local
  activate the encrypted password of UszxwHyGcg.e6o4z
  names of
  mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
  !
  interface GigabitEthernet0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/1
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/2
  Post description
  10 speed
  full duplex
  nameif Ext
  security-level 0
  IP 125.255.160.54 255.255.255.252
  !
  interface GigabitEthernet0/3
  Description Int
  10 speed
  full duplex
  nameif Int
  security-level 100
  IP 192.168.255.2 255.255.255.252
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  clock timezone IS 10
  clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
  DNS lookup field inside
  DNS domain-lookup Int
  DNS server-group DefaultDNS
  192.168.1.90 server name
  192.168.1.202 server name
  domain delo.local
  permit same-security-traffic intra-interface
  network dlau40 object
  Home 192.168.1.209
  network dlausyd02 object
  host 192.168.1.202
  network of the object 192.168.1.42
  host 192.168.1.42
  dlau-utm network object
  host 192.168.1.50
  network dlauxa6 object
  Home 192.168.1.62
  network of the 192.168.1.93 object
  host 192.168.1.93
  network dlau-ftp01 object
  Home 192.168.1.112
  dlau-dlau-ftp01 network object
  network dlvpn_network object
  subnet 172.16.1.0 255.255.255.0
  the object-group Good-ICMP ICMP-type
  echo ICMP-object
  response to echo ICMP-object
  ICMP-object has exceeded the time
  Object-ICMP traceroute
  ICMP-unreachable object
  DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
  Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
  DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
  Ext_access_in access list extended icmp permitted any object-group Good-ICMP
  Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
  Ext_access_in list extended access permit tcp any object dlausyd02 eq https
  Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
  Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
  Ext_access_in access-list extended permitted ip object annete-home everything
  pager lines 24
  Enable logging
  asdm of logging of information
  MTU 1500 Ext
  MTU 1500 Int
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 713.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
  !
  network dlausyd02 object
  NAT (Int, Ext) interface static tcp https https service
  dlau-utm network object
  NAT (Int, Ext) interface static tcp smtp smtp service
  network dlauxa6 object
  NAT (Int, Ext) interface static tcp 444 444 service
  network dlau-ftp01 object
  NAT (Int, Ext) interface static tcp ftp ftp service
  Access-group Ext_access_in in Ext interface
  Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
  Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication enable LOCAL console
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  LOCAL AAA authentication serial console
  the ssh LOCAL console AAA authentication
  http server enable 44310
  http server idle-timeout 30
  http 192.168.0.0 255.255.0.0 Int
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec pmtu aging infinite - the security association
  trustpool crypto ca policy
  Telnet 192.168.1.0 255.255.255.0 management
  Telnet timeout 30
  SSH 192.168.0.0 255.255.0.0 Int
  SSH timeout 30
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  No ipv6-vpn-addr-assign aaa
  no local ipv6-vpn-addr-assign
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 61.8.0.89 prefer external source
  SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  WebVPN
  port 44320
  allow outside
  Select Ext
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_DLVPN group strategy
  attributes of Group Policy GroupPolicy_DLVPN
  WINS server no
  value of server DNS 192.168.1.90 192.168.1.202
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DLVPN_STAcl
  delonghi.local value by default-field
  WebVPN
  AnyConnect Dungeon-Installer installed
  time to generate a new key 30 AnyConnect ssl
  AnyConnect ssl generate a new method ssl key
  AnyConnect ask flawless anyconnect
  encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
  vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
  username admin password encrypted tFU2y7Uo15ahFyt4
  type tunnel-group DLVPN remote access
  attributes global-tunnel-group DLVPN
  address pool DLVPN_Pool
  Group Policy - by default-GroupPolicy_DLVPN
  tunnel-group DLVPN webvpn-attributes
  enable DLVPN group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the netbios
  Review the ip options
  inspect the ftp
  inspect the tftp
  !
  global service-policy global_policy
  SMTPS
  Server 192.168.1.50
  Group Policy - by default-DfltGrpPolicy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:67aa840d5cfff989bc045172b2d06212
  : end
  DLSYD - ASA #.

  Hello

  Add just to be sure, the following configurations related to ICMP traffic

  Policy-map global_policy
  class inspection_default
  inspect the icmp
  inspect the icmp error

  Your NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other.

  I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured?

  Can you same ICMP the directly behind the ASA which is the gateway to LANs?

  If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA

  Int Management-access

  As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN.

  -Jouni

• VLAN internal cannot access the Internet through PIX501

  Hello

  Im having problems with my current setup. We have Cat3750 switch which acts as a base for intervlan routing. At the same time, we have PIX501 as a firewall.

  the firewall is configured to statically map our Web server to the external network. The Web server is accessible from outside.

  My problem is the following. Internal users cannot connect to the internet. Each user has been defined with gateway for their assignment of VLANS corresponding. VLAN internal works fine but can not access the internet.

  Also, all users within our network cannot ping inner (192.168.1.7) address of the Web server. the Web server is directly connected to the switchport aboard PIX.

  Our facility is the following: modem DSL - PIX 501 - Cat3750 (InterVLan routing) - access switches.

  Pleasee see connected PIx and Cat3750 running config or reference.

  all inpiuts will be highly appreciated.

  Kind regards

  udimpas

  Add a default route on your 3750 score inside the PIX interface.

  IP route 0.0.0.0 0.0.0.0 192.168.1.5

• Client VPN cannot get inside the network

  The VPN client connects to the 2600 on the serial interface, should be able to get to the 10.10.0.0 network beyond 192.168.1.14. The customer ping responds failure of external serial interface address.

  If you still have problems... can you check that there is a static route BOF 192.168.100.0/24 on router 192.168.1.14 and initiate a tracert to a host on the network of 10.10.x.x at 192.168.100.7 and see where it goes... your tests show that the VPN client knows how to get to this subnet, but it seems that there is a problem of routing between 10.X.X.X going 192.168.100.0

  I hope that helps!

• Unable to connect to the internet and VPN in the network.

  I have an ADSL account and when I vpn in our network using cisco VPN 3015 vpn client can't access the internet more locally. I have to use our internal proxy server on the network. Is it possible to make the vpn tunnel but also use the local internet DSL for browsing connection?

  You must set up split tunnelling tunnel, while only some packets are sent through the tunnel, the rest get out in clear packages just as usual.

  In 3015, create a list of network under Config - Mgmt policy - traffic Mgmt - list networks, this list includes your internal networks (you want to be dug traffic). Then go under the group to which the client connects to, on the Client configuration tab, select only the network of tunnels in the list, and then select your list from the drop-down list box. Reconnect and're you good to go.

  Keep in the spirit of split-mining is considered a bit of a security risk because your PC is now accessible from the Internet AND you have a VPN directly in your internal network. If someone can take possession of your PC, then they have access to everything. You can also watch in allowing both client firewall stuff.

• T61 does not connect to the network through a station

  I have a T61hat all of a sudden this week the network connection has stopped working when I am connected through my docking station. If I remove and plug the network cable into the T61 it immediately connects, but when I first connected it does not connect. It was working fine earlier this week. I was reading some email in Outlook and suddenly realized that I had lost my network connection. I tried to run the utility Lenovo system update and the updates of Windows and I'm perfectly up-to-date. A virus scan that found nothing. I tried to uninstall the driver of my network and then restart and allowing PnP to reinstall. None of this has worked. Also, I have a partner who has also a T61 with a docking station. I plugged my laptop on my own and got the same results, so this isn't a hardware problem with the docking station itself.

  Our technicians of equipment replaced the motherboard in my T61 and that seems to have solved my problem. Haven't seen the network problem in a week now.

• Cannot depend on the network discovery and streaming media

  I use Win7 Pro., SP1.

  Some time ago, the I realized that I can not use home network more. I can't turn on my discovery of home network and streaming media. The network discivery always returns OFF.

  The following services are all on (automatic): support TCP/IP NetBios and DNS Client, Function Discovery Resource Publication, SSDP Discovery.

  Please notify.

  Hello Dudi,

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the question and your efforts to resolve.

  I also know that the inconvenience that you are experiencing because of the discovery of the network and streaming media problems. I'm going to

  certainly will help.

  Network discovery is a network setting that determines if your computer can find other computers and devices on the network and whether other computers on the network can find your computer.

  This problem can occur because of incorrect network discovery and streaming media settings.

  For network discovery, I suggest you use the steps in this article and check if it helps.
  Reference:
  You can't turn on the discovery of network and Sharing Center in Windows Server 2008, Windows Server 2008 R2 or Windows Server 2012
  https://support.Microsoft.com/en-us/KB/2722035
  (Also valid for Windows 7)

  For media streaming, refer to the suggestions of gifted xI replied on 24 December 2010 and check.
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-turn-on-media-streaming-another-Windows-7/b765ec7a-8c7a-4147-8645-fedc3a5fc991

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Cannot connect to the network or perform system restore after installing updates have been

  WIN 7 Home Premium running on a gateway PC connected to the internet via an ethernet connection using a RealTek network adapter for the past 5 years with no problems. Running Avast Pro antivirus / internet security.  09/02/2016, Microsoft and Avast downloaded and installed updates on the PC.  After the PC auto-redémarré as part of the Microsoft updates, I couldn't connect to the internet.  Connect to the network now says unidentified network - no network connection.  The adapter looks like to she always sees the (watch 100 Mbps) connection, but no data packet move.  Device Manager indicates that the unit is working normally.

  I ran through the resolution of the problems of Windows network. I checked the cable was attached, reset the home modem, reset the adapter (toggle), uninstalled/reinstalled using the latest adapter driver available.  I have disabled the Windows Firewall because Firewall Avast wouldn't start.  I disabled all the Avast settings to see if it eliminated the problem.  I tried to run the system restore before the updates but continue to spread the message that there was an unexplained error and restore failed.  All this was done in Normal mode. I restarted mode safe and had the same problems without success.

  I was able to clear the problem by manually uninstalling updates of security Windows which were loaded on 09/02/2016 through the programs and features Control Panel. Then I did the repair of Avast program operation.  I rebooted the computer and the internet connection worked. Then I reinstalled manually updates Windows security on the Windows Update program.