Change partitions g6-1170sp HD

Similar Questions

• Bootcamp for repair after changing partitions in El Capitan

  (For a better format version, please visit this link.) I did have luck with answers on itself)

  I wanted to create a shared partition that I could access between my install Bootcamp and OS X I have been on Yosemite and utility disk would allow me to resize or create new partitions, but I heard that I could do it by upgrading to El Capitan.

  It worked well, I could reduce my OSX partition and create a new partition with the remaining space, however, when I try to start directly in my bootcamp partition running Windows 8.1, I now get an error:

  
  Your PC needs to be repaired 
  
  An unexpected error has occurred. 
  
  Error code: 0xc000000e 
  

  According to some messages that I found, this may indicate that the hybrid MBR is damaged and needs to be recreated, so I tried this by following this link.

  I also tried to boot into a Windows and running recovery disk

  bootrec /rebuildbcd 

  but it does not work. It returns

  The requested system device cannot be found. 

  So, looks like it has something to do with my EFI partition, because according to other messages, maybe I need to assign a drive letter to the EFI partition, but it does not appear when I use diskpart. I see the output similar to:

  
  > list vol 
  
  Volume ### Ltr Label        Fs  Type      Size    Status 
  
  ---------- --- ------------ ----- --------- -------- ---------- 
  
  Volume 0 E IRV_CCSA_X6      UDF  DVD-ROM  4120 MB  Healthy 
  
  Volume 1 C BOOTCAMP        NTFS  Partition 93 GB    Healthy 
  
  Volume 2 D Removable                        0 B      No Media 
  

  However, I think that's because I see when I run diskutil in OS x:

  
  $ diskutil list 
  
  /dev/disk0 (internal, physical): 
  
   #: TYPE NAME SIZE IDENTIFIER
  
  0: GUID_partition_scheme *500.3 GB disk0
  
  1: EFI EFI 209.7 MB disk0s1
  
  2: Apple_CoreStorage Macintosh HD 340.5 GB disk0s2
  
  3: Apple_Boot Recovery HD 650.0 MB disk0s3
  
  4: Microsoft Basic Data Storage 58.7 GB disk0s4
  
  5: Microsoft Basic Data BOOTCAMP 100.1 GB disk0s5
  
  /dev/disk1 (internal, virtual):
  
  #: TYPE NAME SIZE IDENTIFIER
  
  0: Apple_HFS Macintosh HD +340.1 GB disk1 Logical Volume on disk0s2 E516E87A-D86D-459A-904F-FD299B379969 Unencrypted
  

  I even tried refined, that doesn't seem to change anything.

  Another note, my Windows partition is fine, because I can always start using Parallels, just a direct start in Bootcamp is not.

  I am quite confused where to go from here. Nothing seems to work and I've tried several dozen approaches with no luck. How can I fix Bootcamp?

  Article Nerder is one of the worst possible solutions and causes more data loss. It also provides a clear warning. Can you post the output of the following OS X Terminal commands?

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

• Change Partitions and install Windows 7 Ultimate

  I have 2 GB of ram & when I bought my Sony laptop, I got Best Buy Geek Squad partition my 150 GB C:\ drive to have a G:\ and H:\ drive partitions. I want to remove or delete partitions G:\ & H:\ and C:\ use all of the 150 GB less space reserved for shadow copies of backup.  Disk Mgr, I cannot extend the C:\.volume. After I develop C:\ I want to upgrade Vista Ultimate to Windows 7 Ultimate, or install a full version of Windows 7 Ultimate, regardless of the method will work best... All my data is backed up & I have all my DVD software if I have to reinstall all my programs.  What is the simplest and most accurate procedure to implement these two changes? Aka VDS disk management won't allow C:\ to extend its volume in the free space of 50 GB. For some reason, backups of photos take almost all C:\ 100 GB with free space only 1.45 even after I have remove all except the most recent backup.  I am very frustrated and if I knew how, I would go in the BACK, rub everything and load Windows 7 Ultimate full version and start all over again, but I don't know enough to know if it will work.  I appreciate your instructions... Thank you.

  Since you have backups of your user files and your programs can be installed again, the simplest method is the one that is most likely to lead to a stable system of Windows 7 for long distances. Boot from the Windows 7 DVD. Use the facilities on the DVD to remove all the present partitions. Next, install a new Windows 7 system hard disk. Once completed the installation stage, let the system updated with all the security and update other Microsoft offerings. Then, install your programs, and copy backup your user files.
  It is also possible to boot from the Windows 7 DVD and use its facilities to remove G and H. Then you can develop C to fill up the drive and install Windows 7 on C.
  There are tutorials on Details he to do that and other options on the web.
  Tom Ferguson

• CUCM administration bulk - bulk change partition for CTI Route points?

  Hi support them.

  I was wondering if anyone has encountered this... I'm trying to block of the waypoints for the ITC 100 + change in another partition within CUCM 8.6.2

  I have made the numbers of phone book in the past, however impossible to find a way within the administration of the bulk to the CTI route points. Anyone has an idea on how to achieve this quickly and simply?

  See you soon

  You cannot update CTI Points of the road as you can with the phones of update, you should delate them and re - add with BAT

  =============================
  Please do not forget to messages useful rate, by clicking on the stars below.

  =============================

• Follow-up change partition and swap partition

  Hello

  Using oracle 11.2.0.3.

  We have a summary table which has replaced entire partitions every night by an exchange of partition whenever data is modified. for us to have a compression.

  This table is composite date range / hash-partitioned

  We are consideruing either to build a summary table or mview on this summary with the same strategy partitionin table.

  A read partition the track changes to refresh this second mview since requires no newspapers mview but was wondering if would work in our scneario.

  Anyone know if it would work - make some conditiosn must be met for 'updating fast/incremenatl' take place.

  Now second summary table/mview would be simple counties + sum of data in the first table aggregated measures but high in order to reduce the amount of data.

  Achieve couldn't track the separate use if wanted to use partition change.

  Thank you

  What you have said I think you could make this work.

  On the other hand, if you do not have 'normal' mview updates via a mview diary and only refreshing the mview as a side effect of the exchange of partition I consider simply write the code to make your table a partitioned table, write 'create in select' / 'Exchange' in order to keep the summary table.  It would be probably more effective than the generic approach of Oracle.

  Concerning

  Jonathan Lewis

• Changing partitions...

  My Mac is saved on an external LaCie drive that has multiple partitions, as shown. It is rarely used and has 17 GB of unused space that I want to add to the partition of LaCie SuperDuper.

  How can I move it's space, bringing together two icons on the desktop?

  

  You cannot "merge" two partitions. It would mean so reformat the disk and selecting a new partition scheme.

• Windows is not booting - recent hardware change

  Hi guys,.

  I have an imac 21.5 2011 mid running el capitan (10.11.6)

  In this imac, I have a bootcamp partition (windows 7) that used to work fine until I tried to resize the partition.
  To resize, I used the Mac os disk utility to free up the space in the osx partition and used minitool partition Wizard on the side windows 7 back this free size.

  Therefore, seems to be bcd windows was broken and I can't start windows more.

  I tried:

  • following this subject: no boot after device changed partitions
  • try to do a bootcamp-> could not start him even usb key using down option (only macos, bootcamp and recovery disks available)

  I saved the bootcamp partition (copy of files and also do a dump of R/W dmg from it)

  What can I do now?
  I can't use windows recovery options that I had set on pc because it does not start on the key.

  Could you help her?

  Thank you very much.

  You need a W7 DVD to boot from and repair Windows. For the record, terminal of OSX, please after the release of

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  Orders 'sudo' will ask for your password.

• How to set the size of the partition you want on the Satellite C850-12D with W7 Pro?

  Hi all
  I recently got a new laptop, Satellite Pro C850-12D with seven Pro: disk (500 GB) is first broken down like this:
  -a hidden little, 1.46 GB
  -the folder C: one, Go 449,47 (visible by the user)
  -a hidden, 14.83 Gb

  I would reduce the C: 100 GB partition in order to create a new one for the DATA.

  So, I begin the process by using seven disk management tools, but the disposable size after reduction seems limited to a maximum of GB 226,685: C is greater than or equal to 233 570 GB.

  I tried defragmenting C but its minimum size is 233 570 GB

  Is there a method to overcome this limit and achivce my goal of 100 GB?

  Hello

  I highly recommend creating a recovery disk before you change partitions on the HARD drive!
  The Toshiba recovery media creator helps you create this disk and this are necessary in case something would be wrong with your HARD drive.

  Back to the question of the partition:
  You will need to use a 3rd third party tool like * Gparted * in order to change the size of the partition.

• How can I configure Satellite A300-148 boot from the recovery partition?

  Hello

  I had some problems when trying to install MAC - OSX, for her, where the partition table is deleted, then I retrieve the entire score as it is, but I can not start in any case.
  Then I decide temproraly install another copy of vista drive Vista (not the partition), then set up my laptop to boot from the recovery partition and reinstall the good copy.
  My problem is, it's all here, the only problem is, I need to configure the system to boot from the recovery partition.

  My device is:
  Satellite A300-148

  Thanks to the device.
  Ahmed.

  Hello

  If you have already changed the partitions of HARD drive and deleted files from the HARD disk, then your HARD drive recovery is too bad!

  But to make sure that the HARD drive recovery is not possible please press F8 immediately after the power of the laptop. Usually a start menu should appear and you should be able to choose the option called fix my computer. Then you should be able to choose recovery option.

  But like I said that this is only possible if your HARD drive was not formatted!

  If you have formatted the HARD drive and changed partitions then you will need a Toshiba DVD recovery that you have not because you didn t he create at the beginning. Is this good? Well, then you must order the recovery DVDs if you want to retrieve the laptop to factory settings.

  Welcome them

• HP Envy M6: How to change partations when installing a windows recovery.

  Hi guys, I have a query imp and I did discuss with the experts here,

  I bought a HP ENVY M6 and its partation is very iritating to me, there 750 GB hard drive and it is partationed in 4 disks providing 100 GB 250 GB 200 GB 100 GB partations doing like this, my records are presented in a photo... I don't like this partation, I dun use too readers it irritates me, what I like is 3 disks, disk hard 100 GB C for windows, 100 GB for my data imp as works, studies and pictures etc and the rest mix 500 GB for movies and songs and games,...

  So, my problem is that my laptop has windows genuine in there and I don't have a cd box or the key of windows with me, it came pre insalled. so I don't have the key for activation with me, I have just the RECOVERY DISC as pictured.

  

  what I want to do is I want to install windows from the beginning and I want to do partation again and format records there, too, is it posible I go to the home screen format partations and partation partations and then install my this windows from the RECOVERY DRIVE, coz I want this windows genuine...

  the option of partation windows give at the beginning of installation illustrated

  yuzzii wrote:

  is it possible that I have make a usb bootable from the recovery disk and start the installation of him?

  pls see this post, full

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/I-want-to-change-partitions-when-installing-Windows-from-a/m-p/4889272

  Who is spamming. Don't create messages about the same thing. I won't answer any questions about the same thing in another post by you. See and read the rules for participation that you have accepted.

• How to create Secureboot DELL PE disk with NTFS partition

  Hi Tyler

  I tried with /secureboot command line switch, but its not allow me to change partition to NTFS format.

  Answer me as soon as possible

  Thank you

  Deepak

  Deepak,

  To start under UEFI, you need to boot from a FAT32 partition and since USB Thumb drives allow only one partition, the tools for FAT32 only locks. A secondary drive which is NTFS, or even a network drive could be used to store your WIM files if they are bigger, then the limitation of 4 GB to FAT32. Just start with the key USB ImageAssist and point the tool corresponding to the NTFS drive or use it to map a network drive.

  Thank you

  Gary

• Adding partition in the cos

  Hello

  On one of my servers of homelab, I can't seem to add local storage as a vmfs volume. I have two identical hosts with 650 GB of local hard disk in it. Host esx03 I have on the part of those 650 GB configured for the COS and the remaining part as local VMFS volume. But on the host esx04, I can't seem to configure it.

  ESX03:

  fdisk-l

  Disk/dev/sdd: 640.1 GB, 640135028736 bytes

  255 heads, 63 sectors/track, 77825 cylinders

  Units = cylinders of 16065 * 512 = 8225280 bytes

  Device boot start end blocks Id system

  / dev/sdd1 * 1 140 1124518 + 83 Linux

  / dev/sdd2 141 154 fc VMware VMKCORE 112455

  / dev/SDS3 155 77825 623892307 + 5 extended

  / dev/sdd5 155 77825 623892276 fb VMware VMFS

  On ESX04, it looks like this:

  Disk/dev/sdd: 640.1 GB, 640135028736 bytes

  255 heads, 63 sectors/track, 77825 cylinders

  Units = cylinders of 16065 * 512 = 8225280 bytes

  Device boot start end blocks Id system

  / dev/sdd1 * 1 32 83 257008 + Linux

  / dev/sdd2 33 9213277 1179 + fb VMware VMFS

  / dev/SDS3 1180 77825 615658995 5 extended

  / dev/257008 1211 1180 sdd5 + fc VMware VMKCORE

  Now, I did these commands to try to add an additional VMFS volume:

  Fdisk/dev/sdd

  Command (m for help): n

  Control action

  l logical (5 or more)

  p primary partition (1-4)

  l

  First cylinder (1212-77825, default 1212):

  Using the default 1212

  Last cylinder or size + or + sizeM or + sizeK (1212-77825, default 77825):

  Using the default 77825

  Command (m for help): t

  Partition number (1-6): 6

  HEX code (type L to list codes): fb

  Type of system has changed partition 6-fb (VMware VMFS)

  Command (m for help): w

  The partition table has been changed!

  Calling ioctl() to re-read the partition table.

  WARNING: Re-reading the partition table failed with error 16: device or resource busy.

  The kernel still uses the old table.

  The new table will be used at the next reboot.

  Error closing file

  Now after reboot the partition disappeared again.

  Any tips?

  http://www.GabesVirtualWorld.com

  Hi n,

  It seems that the partition is in fact not be written correctly, which is usually the case when I/O is the disk that you are trying to update. Unfortunately, this creates obvious problems when dealing with local disk.

  First of all, I would recommend using the ESX partedUtil command. That's what the VI client calls on the back-end when the host application to perform the work with partitions.

  If partedUtil does not write successfully the partition, boot disk rescue/live Linux of your choice. The Linux operating system will run entirely in memory, so no I/O does happen directly on the drive, which will allow you to change the table to partition without difficulty.

  It may be easier to use the tool to free opensorce, GParted (http://gparted.sourceforge.net/).

  See you soon!

  Steve

  There are 10 types of people in this world. Those who understand binary and those who do not.

• External HDD DWC 3 130 TB good size and lost data

  Hello

  I have all the backup data on my external HARD drive and other important data photos.
  I have a problem with my laptop and I used the backup (MBR, etc.).

  I also use Partition Wizard Home edition to resize my hard drive in my laptop.
  Unfortunately, after that in windows 8 Toshiba external HARD drive disappear.

  I used two software to find out what happened.
  One does not find the Toshiba HDD, the second find the HARD drive, but first of all, the size which show me was 14.66 TB and all partitions and data was missing.

  How to solve this problem and how to recover my data?

  Thank you.

  Hello

  I guess that's your HARD drive:
  http://www.Toshiba.com/us/accessories/storage/Canvio-desktop-hard-drives/3TB/HDWC130XK3J1

  I guess due to changing partition size, the size of the partition has changed and now it s not visible using the 3rd party software.
  To be honest, I have no idea of what changes have been made, but without doubt, you will need to create the partitions with NTFS file format once more.

• I am interesting to install Linux in Satellite 300 d - 22K

  Y at - it any linux distribution recommended for Satellite 300 d - 22K?

  I have two partition in C: it is the Windows operating system. normal and E: HDDRecovery. Is it possible to install linux in safe E: and HDDRevery unit in usb pen?

  Thank you.

  Just something important for you: recovery image is saved in this folder HDDRecovery. If you remove from here or change partition, you will not be able to reuse this image.

  If you want to create this DVD using "Toshiba Recovery Disc Creator' of recovery. When you have this DVD of recovery facilities, you can do what you want. Later, you can use this DVD to reinstall Vista.

  You can try to install Linux, but please note that this model of laptop is not made Linux supported.

• Satellite C870D-12F initialize Win8

  Hello

  My Satellite will not start (windows 8) more, and I'm not as able to reset to the factory settings.
  The hard drive is still ok if I put it in another PC I can see all the partitions.

  Someone at - he sees something wrong in the properties or the partition type?

  Thanks in advance for any help.

  Sincere greetings

  + The message was edited: part of the message has been deleted.

  First of all: I won't help you if you change partition properties.

  Is that if the partition has been modified in the past or if the recovery files have been removed, deleted or moved to another source and then recovery of HARD drive option is not available more!

  So even if you would try to change the recovery partition now, it will not help because the flag which marks the partition as the partition recovery more isn t valid.

  You the last chance to retrieve the laptop to factory settings is the use of the recovery media.
  If you n t have this support, you can order the CD here:
  http://backupmedia.Toshiba.EU/landing.aspx