Change the amplitude of the Agilent function generator output while the output is on

Similar Questions

• function generator (HP 33120) running to the superior at 1 kHz by Labview

  Hi all

  To run a function HP 33120 Labview generator, I downloaded a driver "Agilent 33XXX Series", also attached to this message. But the files of vi (for example 'Waveform.vi Standard' or "Arbitrary Waveform.vi") available in this driver, do not allow the function generator generations a more signal of 1 kHz, while I need about 200 kHz. Manually the function generator can easily generate a signal to 15 MHz.

  So I need a pilot/vi of this function generator that can generate a signal to about 200 kHz. Kindly help me.

  Thanks in advance

  Concerning

  Fadi

  Dear Dennis

  I think I had hardware problem where I was able to change the frequency of 1000 Hz and 999Hz and so one but I was unable to move from 1000 Hz to 1001hz and so on. But now it is resolved.

  Thanks again

• NI LabVIEW driver for the SRS DS345 function generator generates error "(Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system."

  Hello

  We have a generator function SRS DS345.

  I just downloaded the driver NOR for the instrument on http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9149659CE034080020E748....

  After installation, the DS345 appears in MAX, and I can well communicate with him.

  However, if I run the srds345 to Started.vi, I get an error "location information insufficient (Hex 0xBFFF0011) or the device or resource is not present in the system" from initialize it with Options.vi srds345 sub - vi.

  The only change I did Exchange address GPIB 14 to 19, which is our function generator GPIB address. In addition, the

  Functions of SRS DS345 generator of function palette is empty, even after you restart LabVIEW (see attachment). I'm using LabVIEW 8.5.1.

  Your help in resolving this issue is appreciated. Thank you.

  Best regards

  Peter

  Have you installed the driver from LabVIEW or copied directly from inst.lib?

  The first is easier, and you don't have to restart LV more...

  Error in a not filled gpib address points. I have not checked if this driver has a resource name visa or a string of gpib address old but in the first case, try the little triangle on the right at the slect address instead of by hand.

• Continuity of the functions of the basic function generator and the right time

  I need to create a sine wave, point by point, which will be forwarded to the MIP and finally to a channel of analog output on a PCI-6014

  Ive tried a few different ways to do it, but everyone has some problems with her slider.

  with the 'generator.vi of the base feature.

  and also the "sine waveform.vi.

  There seems to be problems with this lack of points.

  someone helpfully pointed, its very likely windows interrupts the origin of the problem

  Here is a schematic representation of the panels front and rear

  the back panel

  

  the façade has a few points that are missing

  

  Another way to do that seems to work better known that the signal "simulate" express vi.

  It's great because it's actually a way of sine 1htz occur at 1htz.

  There are also all the points.

  The problem is that as soon as I put in my request, she grinds to stop.

  Program speed about changes 10khtz less than 1htz when the basic function generator is replaced with this express vi.

  

  A third idea or concept that has been proposed is to put a programmer to slow the timetable.

  It is once again, works fine, no more points are missed in the plot.

  Yet, he kills again the speed of execution of the program as everything can wait 1ms (or the recripocal of sampling points interval time).

  

  Someone at - it an idea on how I can get a sine wave in PID, then, in the analog waveform without a huge amount of the efficiency of the program. Im sure this is simple.

  Nevermind

  accedanta do the 2nd option from the top.

  go just to increase the number of samples for now leave the rest of the fastest of the program

• Cannot change PopUp LOV width and height in version 4.2.5.00.08. I change the values of 450 400 in the Popup list template values (Section of the window), but my function genList0_f07_$ _row (), retains the same settings. Is this a bug?

  Hello

  I use APEX 4.2.5.00.08 to my app.

  I have a region of reports, where I display a column set. A column is the column attribute "display as" the value 'Popup LOV (LOV based query).

  I press the button to retrieve the LOV, I get a popup of 450 x 400 pixels.

  I go to the side of the model and navigate to "Popup list of values of model", where I can see in the section 'Window' attributes 'Width' and 'Height' value 450 and 400. I edit them and save them and there is nothing going on. I'm sure that the template belongs to my selected theme.

  I saw in the HTML source code that is the called function:

  <!--

  
  function genList0_f07_$ _row)
  {
  w = open ("wwv_flow_utilities.gen_popup_list" +)
  « ? p_filter ="+
  "& p_name = ' + escape ('f07') +.
  ' & p_element_index = ' + escape ('0') +.
  ' & p_elem_id = ' + escape ('f07_0000').
  ' & p_form_index = ' + escape ('0') +.
  ' & p_max_elements = ' + escape ("") +.
  ' & p_escape_html = ' + escape ("") +.
  ' & p_ok_to_query = ' + escape ('YES').
  ' & p_flow_id = ' + escape ('114') +.
  ' & p_page_id = ' + escape ('100201') +.
  ' & p_session_id = ' + escape ('16021544706004').
  ' & p_eval_value = ' + escape ("") +.
  ' & p_translation = ' + escape ('NO') +.
  ' & p_lov = ' +.
  ' & p_lov_checksum = ' +.
  ' & p_item_id = ' + escape('-683997768') +.
  ' & p_column_id = ' + escape ('25022622060292812'),
  "winLov,"
  "Scrollbars = 1, resizable = 1, width =400, height =450"); "
  If (w.opener is nothing)
  w.opener = auto;
  w.Focus ();
  }
  ->

  I see that the values has not changed. I also connected and disconnected. I am inclined to believe that it is a bug of the APEX.

  The only solution I think is to replace this function, which is NOT ideal.

  Thank you

  Digital

  The parameters are generated only, nothing you can do about it because it does not use the model for these properties of the couple. Other things work fine for example the names of button or title window etc. I guess that, Yes, it is a bug. It's still there in the apex 5 too, I checked. The default values of the template do not match, the value in the generated code is always 400/450. So I guess it's pretty much a wait on 5.1.

  Here's a fun hack to make it work well on your page (works in apex 5 too, because the code is always the same). Put this in the execute on loading of the page section:

  (function(){
    var _open = window.open;
    window.open = function(){
      if ( arguments[1] === "winLov" ) {
        arguments[2] = "Scrollbars=1,resizable=1,width=500,height=700";
      };
      return _open.apply(window, arguments);
    };
  })();
  

  Change the settings to your liking. This will replace the existing window.open call, which is what the popup lov use and replace it with our own code. It does not interfere with other things. As the name of the new window is always "winLov" for the popup lov, it is the argument that is checked.

  During the call to window.open to open a new window with the name "winLov", parameters are replaced with your own version of it. The window is called as usual, using the stored reference.

  Edit:

  Yes, do not use the trick of resizing. My hack can be a bit tedious, but it's much less invasive for the end user (see open, bam, resize. "Even gets funky on multiple monitors). Also, this thing in the popup lov template will affect each lov popup that you use in the application, which is much less interesting than my specific page code.

  Edit2:

  I did a little digging in the source code, and I don't know why it does not work. Popup lovs are actually equipped to deal with it. My guess is that the parameters are recovered only after that the lists were generated, causing the package variables global to use their default values instead of model parameters.

• How to dynamically change the generated query through the "query by example".

  Hi all. I'm relatively new to the ADF, so I've been beating my head against a wall trying to figure out how to do this... Any help would be greatly appreciated!
  
  What I try to do is to make a custom search (query) against a set of tables in the database. Normally, I would use just the ability to "filter" the af: table to do this (query by example). However, the query I need to run has three specific requirements:
  
  1. I need to change the 'WHERE' clause differently according to the field in which the user enters criteria in. For example:
  -If the user enters something in the field 'name' of filter, the default ADF BC will do is add '%' to the value entered, turning it into a query "begins by". I also want to prepend a '%' to the input value, (for example "doe %'), it becomes a query 'contains '. I don't want the user to see the '%', I put at the beginning of the field in the UI, however.
  -If the user enters a value of 9 digits in the field 'SSN', do a query of "accurate". If they penetrate only 4 digits, do a query "ends by". (I could always just a query "ends by" - for example "% of values" - even if they have put in 9 digits, and that would work.) However, an exact match will run faster because of the index on the field, so I want to use that if we put 9-digit.)
  
  2. I also need to change the SELECT part of the query based on which fields are used in the filter.
  
  3. If the user enters the filter values in several fields, I need 'OR' them together. The default functionality, it's that they are 'linked' together.
  
  Can someone point me in the right direction? My thought was somehow replace the manner in which the query is generated when the user presses ENTER to run the filter. But, I can't seem to understand where and how to connect it to this process to customize the SELECTION and WHERE the parts of the generated query. I'm sure that there is a way, and I hope more experienced ADF'ers can direct me to the solution.
  
  Thank you!
  
  Published by: 926392 on June 25, 2012 15:39
  
  Published by: 926392 on June 25, 2012 15:40

  Check this post in the ADF Code corner for the necessary information:
  http://www.Oracle.com/technetwork/developer-tools/ADF/learnmore/30-table-filter-queries-169172.PDF

  Thank you
  Nini

• Need to change the generated text automatically report pdf

  I implemented the pdf but it generated text from xml autogenrated.
  
  If I need to change this text then what should I do for this?
  
  
  Here's my xsl file and the output generated in pdf format.
  
  <? XML version = "1.0" encoding = "UTF-8"? >
  < xsl: stylesheet version = "1.0" xmlns: xsl = "http://www.w3.org/1999/XSL/Transform".
  xmlns:fo = "http://www.w3.org/1999/XSL/Format".
  xmlns:fn = "http://www.w3.org/2005/xpath-functions" >
  
  < xsl: output method = "xml" Indent = "Yes" encoding = "utf-8" omit-xml-declaration = "yes" / >
  
  
  
  
  < xsl: template match = "/" >
  
  < fo:root >
  
  < fo:layout - master-set >
  < fo:simple - page-master master-name = "my page" >
  < fo:region - body margin = "in 1" / >
  < fo:region - before measure = 'in 1' background-color = "silver" / >
  
  < / fo:simple - page-master >
  < / fo:layout - master-set >
  
  < fo:page - master-reference sequence = "my page" >
  
  
  < fo:static - content stream name = "xsl-region-before" >
  < fo:block height = "150px" width = "1024px" background-color = 'blue' >
  < fo: external-graphic width = "340px" src = "http://localhost:9000/web-determinations9000/images/logo.png"/ > "
  
  < / fo:block >
  < / fo:static - content >
  
  
  
  < fo:flow = "xsl-region-body" flow-name >
  
  < fo:block >
  < xsl: mode if apply-templates = sΘlectionner 'dump' = ' / session, entity, instance, attribute "/ >
  < / fo:block >
  < / fo:flow >
  < / fo:page - sequence >
  < / fo:root >
  < / xsl: template >
  
  
  pdf output-
  
  What is the student card? =
  65.0
  Is scored more than 80% % = true
  true
  What is the name of the student? =
  ASF
  What is lastname? =
  ASDF
  Student is eligible for the gold medal? =
  true
  
  
  If I want to "is the student card?" the text-only student Id then what changes I need to do this?

  Hello

  Here is the sample code for your understanding:

  
  
  
  
  
  
  
  
  
       
            
            
       
  
  
  
       
            
            
            
       
  
       
            
            
            
       
  
  
  
  
  
       
            Student ID:
       
  
  
  
  

  Thank you
  Aakarsh

• Pavilion x 2 10-n101nv: how to change the function keys

  Hello I have the hp pavilion x 2 10-n101nv, the F function keys selection key works it is light slight increase use and on but if I press the fn becomes F1 F2 F3 f4, how can I change

  Hello

  You can change the default action as follows.

  Shut down the laptop.  Tap away at the esc you key start Notepad to open the Start Menu.  Select the Bios ( f10 ) option, and then change the figure in the document at the following link.

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c02035108 & DocLang = in & docLocale = en_US &...

  Kind regards

  DP - K

• Green function screen changes the video original colors

  Hello.
  I just started using the green screen feature in iMovie and it works great except for one thing.
  It changes some of the colors in my original video and I can't seem to fix it.
  The top image is therefore the original video with green screen and the 2nd image when the functionality of greenscreen and the bottom are applied.

  As soon as it is applied, it changes dark blue skirt of the topic to the violet and also adds a purple tint on silver back, his sword and his shield.
  I tried with different backgrounds and it still changes the color. Also tried in iMovie and same problem.
  If the blue skirt was perform the greenscreen function, it would turn out just see through, is not?
  Any ideas on how to fix it? Thank you in advance! * NOTE: Screenshot taken in iMovie, but I tried them both and same question *.

  

  Lla problem is the magenta used to counter green in the suppression of spill. I don't know how to control it in iMovie, if it is still possible. The question on the forum of iMovie.

• Change the function of the shortcut key of media on the laptop itself player

  Hey everybody,

  I was wondering if anyone knew a way to change what is the shortcut key to player of media on the laptop itself? I have the power button / stop, Internet, Media Player, Play/Pause, Stop, Rewind and fast forward, but the Media Player shortcut key is pretty useless to me and I would like to change its function, to open Outlook instead, but nobody knows if it's even possible?

  I'm almost certain that there is a way, but I can't seem to find, if someone can help me, then I would be really happy,

  See you soon.

  Hello

  I remember that it was possible to attribute the different functions of the control buttons on several units.
  I put t know which unit you use, but you should check the application of Toshiba control buttons that could be installed on your laptop.
  You should find it in the control panel

  This application could allow lets you configure the control buttons.
  But if this software does not have this option, you will not be able to change the features

• How can I change the function of the multimedia button in my keyboard?

  Hello

  I want to change the function of the media in my keyboard button, because if you press the button, the media Center launch, but the problem is, I can´t use the media center due to many reasons, so I want, when I press the media button, only Windows Media Player launches and not the Media Center?

  Who knows what I have to do?
  Thank you very much for your help!

  Hello Sailor

  Can you please write what model of phone you have?

  Anyway, check it please Toshiba controls tool. You can find it in the control panel.

• How to change the feature function keys?

  Hello all I'm new here :)

  I have a stupid problem which is whenever I try to click on the keys function in programs, games, etc... It does not work for this program or game it's just what's on them!

  For an example, when I click F9 or F10 it changes the volume, and when I click on F2 and F3 they change the brightness of the screen! Doesn t refresh F5 and! That s it they do anything, how can I change that to their old original methods as in Windows Vista and XP!

  I don't know if the problem is with Windows or Toshiba laptop, I have a Toshiba Satellite Windows 8.

  Pleaaaaaaaaase help someone! This is urgent.

  You can change to operate in standard mode.
  To make this assignment of Toshiba Office Open > system settings > keyboard and change mode Standard mode F1 - F12 function keys.

  After the reboot it check again.

• Satellite L305 - how to change the function of the media player keys?

  How can I change the function of my buttons in Media Player on top of my laptop?
  I know that if you go to Toshiba Assist, optimize, Support Button, you can change the function of certain keys, but the only options I have are the keys Mute and the CD/DVD.
  [http://img52.imageshack.us/img52/4572/toshibabuttonsupport.jpg]
  I am trying to make the button media player opens iTunes, not WMP and even for play/pause, stop, fast forward and rewind.

  Even if I'm here, I have a problem with my Ctrl + 1 never work. I can't spend the first tab of firefox or aim. I can't do a group control 1 when you play. Anyone know why/how can I fix it?

  Hey,.

  If you press the button on the media player, only Windows Media Player or DVD Toshiba player can be started and not iTunes. This configuration is not possible. As you can read in the user's manual, only these programs can be started.
  Then the other multimedia keys work correctly, and you can use it with media player?

  Concerning your other question:
  I would try to clean the cooling system using a jet of compressed air. This can blow the dust cooling fans and, therefore, it of not necessary to disassemble the laptop.

• Is it possible to change the function of the buttons play/Pause on Satellite P100-347

  Hello.

  I would like to would like to know if there is a way to change the play / pause button on my phone to stop the opening of windows media Center. I like to use itunes to listen to my music and the other buttons (back, forward and stop), all work with other programs, but there is no way to use the play and pause function without opening of the Media Center.

  It seems that you can only change the internet and function of CD/DVD in the Panel.
  Thanks in advance.

  Hello

  Just reply: no, not possible to change playback / pause feature keys s

  The Toshiba control utility offers two options.
  It allows you to assign and select a program for the internet button and touch CD/DVD.

• How to change the default function of the function keys f1 to f12

  I prefer to use as FUNCTION KEYS function keys. I don't want the default value to a fast forward or backward, stop or sound options. I want f2 f2 (edit excel cell) and so on.

  Currently, I press fn everytime. It's boring.

  Is it possible to change the default key for what was originally planned? HP did find that impossible so far.

  On a HP G72 laptop keyboard.

  You can disable this feature by turning off "Action keys Mode" in the BIOS...
  
  Here is the document, which will help you in this... http://support.HP.com/us-en/document/c02035108