change the configuration

Similar Questions

• When I opened a NEW TAB, it loads 'Bing' - no matter what I try! especially to try to change the configuration settings

  Hello

  When I opened a NEW TAB, it loads 'Bing' - no matter what I try! especially to try to change the configuration settings!

  (Note I recently installed DivX player / converter / movies.. .is this the cause?)

  Then... on desktop... .double click on Mozilla... .loads ok
  Open a new tab..it loads Bing! & I hate it!

  Ive tried;

  1.Tools - options - addons - extensions & plugins - cant see anything there?
  2. On the small address bar (top right) which allows search engines to be managed - all cleared down except google & yahoo
  3. Tools - tab mix plus options - New Tabs - Load on new tabs set to Home Page (doesnt let me change it - greyed out url (conduit.com - see 5 below)
  4. Tools - tab mix plus options - New Tabs - Load on new tabs set to new tab Page - displays the url below (5) but if I try to edit it reverts back every time
  5. If I enter "about:config" & then "browser.newtab.url" in the URL bar I get
  
  browser.newtab.url;http://search.conduit.com/?ctid=CT3321897&octid=EB_ORIGINAL_CTID&SearchSource=69&CUI=&SSPV=&Lay=1&UM=5&UP=SP88BDE404-3DB6-49C4-97F5-96A64775CC57
  
  - rightclick on the selection and type 'reset' IT WONT CHANGE
  
  please can you help me?
  

  Thank you

  Stuart

  I see no mention of the duct. com in your initial post. It is often a good indication that you will taken place unwanted software.

• Can not change the configuration extreme airport

  Hello everyone, the community can maybe help me.

  I am a long-time Apple guy and can usually solve my own problems, but this one left me speechless. I have an Airport Extreme ages of less than 1 year. I set up OK and used for the last year. Now, I want to change the configuration. Specifically I add a port to the front, but I also had this problem, try to change the MAC address access lists, changing the wireless channel, allowing access as a guest, and probably any other change in config I try.

  Anyway, once I made the change, not restarting airport but then it fails to return to the top. The yellow light comes on and sometimes the utility Airport told me that he was unable to update the config. In this State I have to pull the plug to restart and once I did, the airport is back re-run without the changes I had made.

  It doesn't matter if I use the Airport 6.3.6 on El Capitan utility or Airport utility on iOS 9.2. The result is always the same. No change, fails to return to the top.

  I did a soft reset a hard reset and a factory reset. I've reconfigured from scratch (several times) and still can't seem to take a successful configuration change. I'm at the end of the ideas. I plan to return it because it's the year is February 2, but I don't want to go through the hassle if I can fix it myself or if it is a known problem that will not change with a change of equipment.

  In any case, here is specific information on the version by any chance, anyone else had this problem or knows a fix:

  Airport Extreme 802.11ac (ME918LL/A)

  Mac OS X 10.11.2

  Airport Utility 6.3.6

  iOS 9.2

  The actual configuration is crucial here.

  We need to know what is the brand and model of the modem?

  Some cable modems are at the origin of the terrible problems... especially the SB series cable modem.

  We should also see some screenshots of your configuration... Summary tab and network...

  We can work from there.

• USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

  USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

  Once again... Thanks for the tips...

• BES 5.0.3 api to change the configuration of account?

  Hello

  I want to temporarily disable the users to send and receive e-mail and messages on their devices.  What I've read, the way to do is to put "Redirect to BlackBerry" 'no' in the account configuration.  The problem I have is that I want to do from a Java application using the BES 5.0.3 Service Web interface and I can't find any way to do this.

  Can I retrieve the current value of the object AccountConfiguration and I see that it has a setter, but what is the method in the BWS interface I would use to change the configuration on the server?  If this is not yet supported, or I forgot something?

  Thank you.

  Hi and welcome to the forums!

  Currently, this feature is not supported. You can set e-mail filters or the folder redirection using BWS, but stop the flow of messages in total is not supported.

  Feel free to submit a request for this feature by using Issue Tracker (link in my signature). It is important when using file a new application to include a good deal.

  Kind regards

• Oracle EBS: change the configuration of the new server

  Hello everyone.

  I'm newbie talk about administering Oracle EBS.

  This is the scenario:

  Oracle 11.1.0.7.0 database

  Oracle EBS 12.1.3

  The single node configuration: database of the layer and the application layer runs on the same server.

  OS: RHEL 5.7

  Virtual server.

  The IT guys have cloned the production server by using the virtual server administration software in order to create a new virtual server for development purposes. The production server has been cloned successfully, the new development server is a host name and IP address different of the production server.

  The head of the computer SCIENCE Department has asked me to work in the new development server. My goal is to change the configuration of the EBS:

  1. change the ORACLE_SID of the Oracle database.

  2. change the ORACLE_HOME of Oracle database and Applications: for example, current ORACLE_HOME is/U01/production and we need the ORACLE_HOME under/u01/development

  3. change the user and group of the owners of Oracle database and Applications directories: for example, current owner of the directories of Oracle database is oramgr user and need to change the owner of oradev user, same case for Applications: current owner of inventories of Applications is user applmgr and need to change the owner of appldev user.

  Of course, it is expected after making changes, the Oracle DB and Oracle Applications must be able to function normally, I want to use the scripts to start and stop oracle the bleachers.

  Is it possible to make the mentioned changes?

  Can you please guide me to do this?

  Thanks in advance guys!

  You will need to follow the steps of the R12 cloning MOS 406982.1 Doc - essentially you are going to use the current instance as the source and make a clone with all the necessary changes you listed, and then drop the source instance

• My Lightroom has lost the connection to most of my photos, records and collections. They are still on the computer. It happened, while moving my laptop when it was running. The mouse is moved and it might have changed the configuration. How can I do my wo

  My Lightroom has lost the connection to most of my photos, records and collections. They are still on the computer. It happened, while moving my laptop when it was running. The mouse is moved and it might have changed the configuration. How can I make my Lightroom works properly again?

  I use Lightroom 6.4 on a Pc with Windows 10.

  Has disappeared? Try file-> open the new item, and then select each illustrated catalog until you find the catalog with your photos.

  If this does not work, please post a screenshot of the problem.

• New router - how to change the configuration?

  I installed a new router but don't have my installation CD for my printer Photosmart 4385.  How can I change the configuration of my network without the CD?   I downloaded the drivers and software site HPO installation, but when I ran the installer, it never asked anything on the network.

  When you start the software, make sure that the printer is not connected to your computer via USB.  Then it should ask if you want to create a USB installation or network.

  If this isn't the case, you downloaded the software "full"?  Do this.

• Change the configuration of the built-in VNC server

  I'm experimenting with a code where I want to spend the VNC server inside the workstation 7.1.2 via the VIX API by writing to the runtime configuration variables. Just now using vmrun to do that, but doesn't seem to work. So the commands are:

  vmrun writeVariable runtimeConfig RemoteDisplay.vnc.port 5900

  These back via the command readVariable reading shows that they have been properly defined. However before you use VNC viewer to connect to localhost:5900 port fails. On the other hand if I enable it in the comments running via the settings dialog box, I am able to connect to the host via VNC.

  Is this a bug, wrong orders or simply not taken care of?

  Hi DaveP,

  I think that would fall under "not supported" for now.

  In my view, the component of VNC server of the running virtual machine process reads these configuration values only when the process starts up (so when you turn on or resume the virtual machine) and then is configured correctly. He will not change his report based on these being defined via vmrun (values are basically just put in a database in memory, there is nothing to say the re component - check the values once you make those calls).

  Basically, the VNC server cannot be configured (enabled or disabled) when running. You will need to power off the virtual machine, change the configuration file and power then turn it back on.

  OK, that last paragraph is not really true, since you can configure the runtime through the user interface. But, it is true, then it's vmrun or VIX. So, the primary response is the same: 'not supported '.

  Post edited by: mattrich

• Changing the configuration of network domestic

  I use an Apple Time Capsule as a router with no problems until now. The current configuration is essentially:

  Cable modem

  |

  Time Capsule

  |         \

  |         Wireless

  |

  Hard line CAT 5 of various devices

  We'll be moving soon however, and I want over the new House to have a network in the wall. I have the skills, tools and parts, my only question is whether to change my configuration will work with the configuration that I have in mind. I would like to change it to:

  Unmanaged switch

  (Cat 5)   /           |           -(Cat 5)

  Cable modem |             Time Capsule

  |                             \

  CAT 5 in other rooms wireless

  My apologies for the crude drawing/plan. Here are my questions: the TC can continue to manage the routing/DHCP for the network in this configuration? A switch works, or should I use a managed switch? Everything that handles routing/DHCP function should she go between the cable Modem and the rest of the network, or it will work at any layer as long as it is not competing with something else trying to do the same function?

  Thanks in advance for any help.

  I'm assuming that your cable modem is a simple modem... only a single Ethernet port on the device.

  Your new network should look like this:

  Internet connection > Cable modem > router (probably your Time Capsule) > switch > Ethernet devices

  Reason... the cable modem can only provide a valid IP address.  If you have a switch connected to the cable modem... it will be a matter of chance as to which device will get the right IP address. All other devices won't be able to connect to the Internet.

  A switch will be thin and easier to use than a managed switch.

• How can I change the configuration for the output channels analog on a PXI-6704?

  I can't seem to understand how to access the configuration of the channels to the outputs analog (channel 33 and 35) for PXI-6704.

  This piece of test equipment is out of tolerance and must be calibrated.

  I have followed the procedure of calibration http://www.ni.com/pdf/manuals/374081b.pdf, but am getting hung up on step 8, where it is said to repeat steps 4-7 when changing the _cal_ao_current_offset. I can't figure out how to open this channel because it is not listed as a physical channel for step 5.

  I'm using Labview 7.1

  Thank you

  Hello! What you need to do is to add 'Internal channels' to your list of channels, so you can choose the _cal_ao_current_offset or _cal_ao_voltage_offset.  This is done through the drop-down list channel right click and select "I/o name of screening...". ».  There will be a check box that says 'Internal channels' and will provide you with all available internal channels to enter your vi Create Channel.  I have attached some photos illustrating how to do. See you soon!

• How do you change the configuration of the drive in the bios with the master and slave?

  When I bought my Dell Dimension 8300 several years ago, I had installed a DVD player and a CD + RW drive and a floppy drive installed in the system.  Very early the system crashed and the OS discs had to be reinstalled.  The Tech is frustrated and accompanied me by changing the master/slave in the bios.  My DVD player is now the master and my CD + RW is now slave.  My cd burner and DVD player play, but they do not burn or import music.  I was wondering if the fact of change that might help the problem with the stopping cd burner just in the middle of a burn error 4450 or ((0X00001162).)  Thanks for your help.

  Hello
  If you are referring to the sequence of boot Yes the bios is where you want to change it see this url http://helpdeskgeek.com/how-to/change-boot-order-xp-vista/ ... . If you are referring to master vs. slave then that is something else see this url http://www.scribd.com/doc/96827/Master-Slave-Configuration access http://support.microsoft.com/default.aspx/kb/283658 Device Manager and check for the x red or yellow?
  itunes error code points? is this correct
  I do not think that it will make a difference to change the devices around, but there's enough information here to know what to do....
  I don't think that changing the order of stertup is going to fix this problem, but again once there is info here to address this issue...
  I would however check the device mgr if there are brands so you can set from the Device Manager and there is news for this
  I think that your problems stem from itunes, if that's the case, it would be best to see if this is the case, however, if the case is you are using windows media player let us know if this post can help solve your problem, please click the mark as answer check on this page THANKS AND GOOD LUCK

• ASA send syslog messages to change the configuration

  On a router, you can send the configuration changes on the server syslog by practice,

  conf t

  Archives

  The config log

  Enable logging

  notify the syslog

  Then the router will send something like:

  . 3 August 13:12:00.776 of the PACIFIC: % PARSER-5-CFGLOG_LOGGEDCMD: user: admin connected control interface: No. Loopback76

  If I had typed in the command line, "no lo76 int.

  How do you do this on the SAA?

  Objective: I want to know when anyone does any kind of config on my ASA.

  The number of syslog 111008 and 111010 will record the command entered by the user.

  111010 concerns the configuration changes.

  Here is the syslog for your information:

  111008:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/system/message/logmsgs.html#wp4769400

  111010:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/system/message/logmsgs.html#wp4769410

  You must turn on syslog and level 5 severity, and if you do not want to see any other record, you can only connect the numbers of syslog 2 above.

• change the configuration of rman in Data Guard envrionemnt

  Hello

  can I change configuration rman on primary and standby without having to stop the replication or swtich?

  the changes are replicated or I have to manually change the two sides? (and what does it matter if im using catlaog or not?)

  v11g

  Thank you

  The changes apply only to primary and standby databases, do not need to change or stop.

  So I highly recommend to read: https://docs.oracle.com/cd/E11882_01/server.112/e41134/rman.htm#SBYDB04700

• How to change the configuration of workflow mailer in the template file

  Hello
  
  I have the setting OutboundUser = changeOnJavaMailerInstall in the mailer WF configuration. I have this empty parameter. That is to say that I want to delete changeOnJavaMailerInstall. I did this front end. But when I run the autoconfig he recovering setting. Please let me know how to make this change permanent. what template file, I need to change?
  
  Thank you
  MSR

  PL file context of search requests (/appl/admin/.xml) to see if you can find the value "changeOnJavaMailerInstall". If so, edit the file and change the value to everything you need, and then run autoconfig and bounce application services.

  HTH
  Srini