Change the speed of data acquisition

Similar Questions

• Is it possible to change the name of data acquisition device?

  Hi all

  Is it possible to change the name of device of data acquisition in a pragmatic way?

  I wish I had at the beginning, when I start the data acquisition control a name that my .net program assigns to the DAQ card. Is this possible?

  Thank you

  Virginia

  Ashly thanks!

  Virginia

• How to increase the speed of data acquisition?

  Hey, currently I using 6210 OR of data acquisition and control switch. I used labview to periodically check the 7 switches and read data from 7 channels in the meantime (1 sample on request). I ran 70 loops for 10 groups of data, the cost of the time looked like 2.2 seconds.

  I would like to end a 700 loops in 2 seconds, is it possible to improve?

  Thank you

  PEM

  Look at the Terminal stop of the DAQ Assistant Express VI. You are starting and stopping of the task for the acquisition of data on each iteration of the loop.

  Starting from the help file:

  Stop

  Specifies to stop the task and release device resources when this Express VI ends execution. For ongoing tasks, this entry is FALSE by default, which means that the task is running until the application terminates. To stop the task, you can use the device again in the same application, wire control wire you the Conditional stop this entry to the same terminal of the while loop. For single-point and finished tasks, this entry is TRUE by default, which means work stoppages after all samples are acquired. To optimize the performance of single point when using this Express VI into a loop, wire control wire you the Conditional stop this entry to the same terminal of the while loop.

  Also from the help file:

  Continuous single point of entry or exit, the of VI Express DAQ Assistant cannot allow optimal operation. See Acq & chart voltage-Single Point optimization VI in examples\DAQmx\Analog In\Measure Voltage.llb for an example of techniques to create more powerful applications, single point of I/O.

• Changed the name of data

  SUMIFS (data: $C, data: $B, $A2, given: $A, "> =" & B$ 1, data: $A, "<" & (EOMONTH(A1,0) will GET ($1.0 B) + 1))

  It's the formula that I used until I changed the names of "data Plan". The original names were:

  A1

  A6

  A12

  B1

  B6

  etc...

  I changed the plan of names...  I want to start all over again... The original formula still works?

  

  The original formula should still work as long as the new plan names are spelled the same in both tables.

  SG

• Cannot change the speed of the WiFi with WN3000 Extende range

  Hi all

  I try to change the speed of the WiFi after successfully connecting to the WiFi network original and extending it with the WN3000. But the drop-down list is blocked. When I connect to the network original WiFi directly speed is up to 300 Mbps, which is why I thought I could also change in the range extender.

  

  Any idea?

  Thank you!

  Daniel

  Hello danaldo

  Then, this is why he is not allowing the 300 SBM because your main router is out which and the Extender that will reduce by half for all the devices connected to the Extender but not if they are on the network from the router. Here is a good article explaining this.

  https://www.repeaterstore.com/pages/WiFi-booster-Repeater-Extender-differences

  DarrenM

• How to change the speed of the RAM on my HP Envy m6 - 1158ca?

  Hello

  I have a laptop of m6 - 1158ca HP Envy (Intel i7 3632QM @2. 2 GHz) running Windows 8 Pro 64 bit with 8 GB of RAM. Supposed to be 1600 MHz RAM speed, but I don't see that 800 MHz through a third-party tool (CPU - Z).

  Are there settings in the BIOS I have change to change this?

  Thank you
  Véronique

  N ° there is no option in BIOS OEM that allow you to change the speed of add-on memory or speed of the bus.

  It is an option that is present in passionate desktop motherboards.

  Computer Systemboards laptop OEM and microcomputers have less optional parameters.

  Best regards

  ERICO

• Yoga 2 13 - How do I change the speed of the cursor Clickpad

  Hi all

  Just a quick question on how to change the speed of my cursor while using the Clickpad/Trackpad. For the time being, it moves quite slowly, I would increase the DPI that it moves.

  I've been through properties and mouse pointing device properties, and I can't seem to find an option here.

  Any help would be appreciated.

  Thank you

  Gavin

  Control Panel/mouse/pointer options. Same as with a mouse.

• How to change the speed of the pointer mouse?

  Hello

  I want to increase the speed of the pointer of the mouse through LabVIEW. Similar to change the speed of the pointer mouse in Windows "mouse properties".

  Thanks in advance.

  Here

• change the speed of the PC at 10 or 100 Mbps Ethernet link

  Hello

  I need to change speed Ethernet from the PC through program which is change the speed 10 or 100 Mbps.

  Is that possible, if yes, then please let me know the procedure.

  Or at least, I should be able to read the PC Ethernet speed in LabVIEW.

  Thank you

  You don't need .net 4.0 for this (.net 2.0 is pretty good) or anything else installed.

  I have attached a VI with control.

  PS: If you need to load assemblies .net 4.0 on to LabVIEW, you must follow the instructions in this link:

  http://digital.NI.com/public.nsf/allkb/32B0BA28A72AA87D8625782600737DE9

• How do I change the speed of moving on Chess titans

  How can I change the speed of the movement of my men of opponents (playing against the computer).  They are so fast, it is difficult to follow who moved where piece

  Hello

  The speed that the movements of the computer is not configurable, but you can see the position of the last piece that moved by searching for yellow flags that will appear on the piece that moved and the Exchequer this piece comes from the post.

  Also you can find some other useful settings to make Chess Titans easier to see by pressing F5 during the game Chess Titans to open the Options screen.

• can xp support a flow rate of 50 MB/s - is there a limit to the speed of data transfer, it can support?

  can xp support a flow rate of 50 MB/s - is there a limit to the speed of data transfer, it can support?

  I have a 50 MB/s via fiber optic connection and it works fine under XP.

  Steve

• Can I change the speed on a GB SFP?

  We have an ASR1002 edge router I need to connect a 100 LH SM Fiber (1310). I have a GLC-LH-SM and a SFP SFP-GE-L. I need to set the speed to the ASR for the interface of the FPS to 100/full. The IOS does not "speed" controls at the interface level. Can I set the speed to 100 for one of them and, if so, how?

  Cannot change the speed for SFP module.

  However, for the 100 M SFP Transceiver compatibility Document (link below), the ASR1002 supports the module of GLC-GE-100FX of 100 MB interconnects (split into a compatible slot in GE).

  http://www.Cisco.com/en/us/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL632702.html

  Good luck!

• I have windows 7. I want to change the speed of my cd disk drive. II am not having luck with the audio CD burning. the 'old' burning well. Help

  I HAVE WINDOWS 7 ON MY DESKTOP COMPUTER.  I'M DELETING AFTER BURNING OF AUDIO CDS TO PLAY ON MY CARS.  OLD CD WELL MADE.  I WAS TOLD THAT IF I CHANGE THE SPEED AND THE LENGTH OF 72 MINUTES AND 650 MB. IT WORKS BETTER.  WHAT ARE THE STEPS TO DO THIS

  HELP ME I'M NOT TECH SAVY AND AN ELDERLY PERSON

  Hello

  Please, do not type using all caps.  It is difficult to read and considered rude/scream.  Be considerate of the visually impaired.

  I think that's what you're looking for.

  Change settings for burning a CD or DVD in Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows/Media-Player-CD-DVD-burning-settings#1TC=Windows-7

• Change the time and date of deposit when importing

  Hi everyone, when I import images in my project, automatically first change date and time with the current date and time in the finder. So each imported file have changed the time and date when I search in the finder under the "created" or "modified" column, is this normal?. There is no way to avoid this?

  Thanks in advance

  Yes, you can prevent this! Go to the preferences of first and go to the media section. Uncheck "Write XMP IDS to files on import". Boom, done. First will not add his small beacon of metadata files when you import them. This isn't a huge deal for most publishers except Adobe apps could create media Cache files more than necessary if you re - use clips in other projects. Don't forget, however, anything, if you change the metadata (in the project Panel or metadata) file, it'll still change changed data for the clips.

• Dynamically change the Format of Date of Application

  Hi all

  I am looking for a possibility to change the format of date of Application in globalization attributes dynamically according to the user.

  Something likeAPEX_UTIL.SET_SESSION_TIME_ZONE but for the date format.

  Does anybody know how it works?

  In detail:

  I want dates in interactive reports display in a specific date format.

  If I put the following in the attributes of 'security' - call the virtual private database PL/SQL to define the security context:

  BEGIN

  If password = "MY_TEST_USER" then

  run immediately "alter session set nls_calendar =" English Hijrah "';"

  run immediately "alter session set nls_date_format =" DD-MM-YYYY "';"

  end if;

  END;

  Then, the dates are indicated correctly in reports interactive but not in the Action menu-> filter.

  If I put date_format = "DD-MM-YYYY" in the attributes of the globalization, it works very well in the interactive report filter.

  The problem is that I want to set this attribute only for some users.

  Thank's,

  Kirsten


  (APEX 4.0/APEX 4.2)

  Because you can use string syntax of substitution for the attributes of the globalization, for example, you could create an element of the AI_DATE_FORMAT application, reference & AI_DATE_FORMAT. and fill out the application element according to certain parameters in the code after the authentication of the authentication system (for example: get a parameter of an array of parameters user or somesuch).