Chassis numbering after power fail? Persistence?

Similar Questions

• UEFI auto turn on after power failure

  I bought a desktop computer HP Pavillion PC500-225es (have a holiday home in Spain where the suffix are).

  It is running Windows 8.1 equipped a UEFI BIOS.

  I want the PC automatically restarts when power is restored after a power failure, but I don't see any option to do this in the UEFI BIOS. Is it normal for a UEFI BIOS? I have had many computers with a BIOS for old style and that I can remember all had the ability to set the auto restart after power fail.

  I don't know how a UEFI BIOS integrates with Windows 8.1 but I see no option for this in point 8.1 of Windows either.

  Someone at - it ideas?

  In addition, because the PC was bought in Spain, the BIOS is in Spanish. It seems not be anyway to change that in English, my native language. Not a big problem I can get in Spanish and may apply to the Google translate if I have to, but it would be easier if there was an option to switch to English.

  I ran the HP Support Assistant, and everything is up-to-date, there is no update to download BIOS.

  I guess I'm just stuck with the situation unless HP come with an update of the BIOS to add installation.

  Please see the BIOS for the motherboard Jasmine settings the settings you are looking for. Although this document is intended for the 'Jasmine' motherboard and your computer uses the "JasmineR', the settings should be similar if not the same thing.

  To access the BIOS Setup page... "Turn on the computer and immediately press the F10 key repeatedly, once per second, until the opening of the Computer Configuration utility."

  The following options are found in the Power Options:

  Messages POST (Power On Self Test)	Turn on or off
  After the loss of power	Previous state, or disable
  POSITION of delay (in seconds)	Zero, 5, 10, 15, 20 or 60 seconds

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• HP Pavilion Entertainment PC: laptop power on password after 3 failed tent and says system disable 15908722.

  laptop power on password after 3 failed attempts and says system disable 15908722.

  Hello

  Please enter:

  00660304

  Kind regards.

• does not start after the fail of power - current

  The machine makes grinding noises rhythmically squaky again and again until I have pull the plug. By pressing the button start does not stop the grinding effort (to start). It allows you to return after a few hours, but this time, there is nothing. It seems that he is not getting enough juice to do more than run fans briefly.

  I took it to a store where they tried to sell me a new machine that I don't want. They were first it upward from the starting System. They defragmented and other stages of the interview, but failed to solve my problem. Alleged that it was the motherboard, memory, etc. I had NO problem before this last failure and run diagnostic in the shop in my previous city with no problems.

  The model is:

  HP Pavilion Elite HPE - 480 t series XM558AV #ABA

  I made no changes to my machine at all because he was running very well and does everything that I needed. The shop removed a memory stick that I replaced as soon as I got home.

  It feels like the machine is not getting enough power to turn on. Fans of turn and stop. The Start button is useless once it is pressed at the beginning and I have to remove the plug to stop attempts to start.

  Starting after power outage has had a problem with this device, but it would eventually start so far. Any suggestions?

  Hi Chris,

  Try the steps listed in the link below.

  http://support.HP.com/us-en/document/c01884928

• HP pavilion entertainment pc: laptop power on password after 3 failed attempts

  laptop power on password after 3 failed attempts and says system disable 50942279. Thanks for giving me a password

  @sky1987

  Enter 45620879

  REO

• Acer aspire one P531h does not illuminate after power to the top

  My netbook aspire one P531h, running on Win Xp 32 bit, shows a black screen only after power on and the power led remains lit steady green. Problems started awhile the 'evil' netbook to start.  After one or 2 low power it started again. Then the battery fails to charge beyond a certain level and now it will fail to start.

  I search the web and forum and there seems to be a BIOS problem.  I found the instructions on how to flash/upgrade to day other models but not this one.

  I tried:

  Method of draining the power as described by lowendguru on youtube and eslewhere.

  I downloaded the new BIOS software, but missing instructions for Flash for this model.

  Looking forward to hear from you.

  Hello

  I sent you a private message. I can't help you more.

• Desktop screen blank after power loss

  This problem seems to have several solutions, but I think I've tried most of them.  I have Windows XP SP3.  Was in the middle of a copy of a floppy disk drive hard when the power failed suddenly.

  Now, the computer starts to an empty office of light blue, but without icons or the Start button.  Can use CTRL-ALT-DEL to run Explorer and run programs.  I can not start Internet Explorer from the Explorer.  Microsoft Help however starts Internet Explorer and I can move around the Internet.  Norton Internet Security begins at the start so I did not have a virus problem.  I tried the recovery system back to before the disaster but I get the same result.  I just tried the Microsoft Hotfix but still the same result.  This program, however, wiped out all my previous Restore Points.  I have tried all the suggestions of Regedit because I am not sure how they correct the problem.  My best guess is that a. DLL or. SYS file is corrupt.  Is it possible to determine what is bad by the processes or Services that are not running?

  Any other suggestions or corrections?

  PROBLEM SOLVED.

  Registry required a change to the value of Shell.

  REGEDIT

  [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon] "Shell" = "explorer.exe".

  I found that the value has been replaced by "progman.exe.

  After the reboot, the computer reported that he could not find a Restore Point from 26/10/2010.  I said not restore at a different point and he finished with a few slight differences in my usual startup; but the Desktop buttons and start were in place.

• Problem after update failed

  Hello world
  today after a failed update my double D6633 Z3 does not start.

  The message "the software update failed. Make sure that your phone is connected to the computer and try again. "flashes on my screen.

  The issue is that PC companion can not find my phone. I tried all my USB ports but still does not work.

  Have you any suggestions?

  Thank you

  You may need to perform a repair of software using PC Companion. The process will erase all internal memory. You might need to charge your device for about 1 to 2 hours until the device has so at least 60% battery.

  Make sure that the device is not connected to the computer or laptop and turned off (sometimes you have to press the power button / stop and volume until what the machine vibrates 3 times or on some devices, it must push the small button near the tray on the back of the camera or SIM).

  Open PC companion-> support area-> update phone software / Tablet-> repair my phone/Tablet blue highlighted. Follow the steps, do not plug your phone until you are prompted to press volume down while plugging in the USB cable. If PC companion does not start the repair process, you may need to run Windows 7 compatibility mode (in some cases XP).

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• HP 280 G1 (N9E78EA): Partition disappears after power failure, watch now unallocated

  Hello!
  I have a PC
  HP 280 i5 - 4590S G1 / 8 GB/500/DVD-RW/W10P + 7Pro64
  and
  Pro series SSD Plextor 128GB 2.5 "SATA SSD M6.
  
  Partition disappears after power failure, watch now unallocated.
  I tried to use TestDisk to see what was going on. After crossing the 'Analysis' command and deep research, but the partition disappears.
  Any suggestions on what I should do next?

  Your SSD have lost files due to the power failure system sudden. I suggest you run CHKDSK to fix this error. Also remember, if the data stored in your SSD are important to you, then first the software of raw data as WDR pro of stellar phoenix recovery and then apply diagnoses to repair.

• Airport Extreme (ME918LL/A) must be Factory Reset after power cycling

  whenever I power cycle the router (at the suggestion of Cox), I end up having to reset completely by holding the small button in the back (for factory reset).

  after power failure cycling or power (it is on a surge protector) he will be a solid clear amber and not actually broadcast all networks.  several fun power do not help, the only thing that works is a clean factory reset.  THEN trying to set up the network using an iphone 6 s (macbook air and mac mini/PC portable airport utility never works) it will take two or three tries, even if I am standing less than 5 feet from the base station, in clear visibility.

  its really begins to age, Wastin' 30 minutes each time that the router is the bike power

  AirPort Extreme is defective and must be replaced. Please contact the Apple Support for a replacement unit.

  Click on the link contact us at the bottom right of this page to get the process underway.

• Power failed and now iMac trying to reboot several times

  Continuous power failed and computer try to restart Gets the part of the journey through the bar on the screen, then restarts.

  -iMac 27 "equipped with the latest system and all software are uptodate.

  -All the devices are disconnected.

  -Tried to hold down option, also I tried shift key and no change in the attempts to restart.

  -Unplug the power cord for a few minutes, but no help.

  Any other suggestions?

  Try to do a reset of the PRAM, if this does not work try starting on the (command-R) recovery Partition at startup and run disk utility - repair disk. If errors appear on your hard drive is damaged and must be replaced.

  Resets of LANDAU and SMC Intel iMac

• Satellite M30X-111 died after about 15 sec after power to the top

  Hello
  My M30X 111 died after about 15 sec after power upward. The blue light comes on, the fan starts and then turns off & the dies machine - however, the blue switch remains on. Then I have to keep the power button up to swith off the machine.

  I can't go as far as the BIOS and it does not start from CD, etc.

  Thanks in anticipation,

  Hello

  The laptop goes to home Toshiba screen?
  If yes there is no hardware malfunction but perhaps something wrong with the software.

  You suggested that it of not possible to enter the BIOS. How have you tried to get into the BIOS?
  As far as I know, this unit uses a Phoenix BIOS so you must press the F2 key immediately after switching on. Press the "F2" key several times to make sure that the option has been enabled.

  The alternative to boot from the CD/DVD drive is using the C key. The same procedure here: press the C key immediately after starting the laptop.
  (the CD must be inserted before you start)

• GSM7224v2 loses the configuration after power failure

  As the topic title says - this device (new for me but flea market) loses its configuration after power off.

  I don't see any button cell within the unit for volatile memory backup. Surely the configuration lives in non-volatile storage?

  I am being dumb and I'm missing something?

  Hi neidlo

  Welcome to the community!

  Yes configuration lives in a non-volatile memory, when it is saved. Until it is saved, it is in RAM.

  When configuring the switch, it is not automatically saved. Using Web Interface (GUI)? A "Save" button should do.

  Please let us know whether or not this was the burden

  Kind regards

• Lenovo IdeaCentre Q180 behavior after power failure

  Hello

  I need a computer that automatically restarts after a power failure.
  I find nothing on the IdeaCentre Q180 behavior in such a case.

  Did the reboot of the IdeaCentre Q180 himself after power failure or is it possible to activate this feature?

  This behavior is very important for my new system.

  Thank you for your response.

  Kind regards
  Theodoor

  Hi theodoor, welcome to the forums.

  I am not personally acquainted with the Q180, but I had a quick glance in the simulator of BIOS and I am sure that the service you're looking for is available in the BIOS.

  Please see the photo attached, (too big to post), it will open in the same window, so please click on your back button on the browser to return to this site.