Choice of cards-red/blue/green transit?

Similar Questions

• solid color 1 color to the constants of red/blue/green

  Hello

  Does anyone know how to convert 1 color.

  Let's say ORANGE.

  his Red value = 16448250

  its Green value = 29535

  blue = value 16711680

  is there a way to know that ORANGE and blue/green value?

  I suppose to do something like that?

  

  Thanks in advance

  Try the RGB VI color:

  

• Given to nine hp w2408 flashes red/blue/green/black/white when idle

  How can I disable this?  I think that it is still factory testing or burn-in mode, but I can't seem to find how to turn it off.

  At least he only does when idle, but I'd rather turn it off except closing cycle through these colors.

  Thank you!

  -Jason

  I actually found a solution for this but what works was to reset the default monitor.  After that, this mode is disabled.

• Features red and green Qosmio F30-117 - display problems-

  Hello

  I have a qosmio F30-117, and until recently, I was thrilled with everything about it.

  Then, mid session, graphics started to deteriorate, which fixed a reboot.

  Then a few days later, he did it again and this time when I rebooted it came with a display corrupted, a lot of aa in all directions then red and green lines everywhere.

  Managed to get by selecting safe mode with network and got a desktop computer but still with red and green lines everywhere.

  Now its got worse again, when I start the screen of the laptop itself is empty, becomes something because it is not completely black as if it was when its engine turned off, but his Blanck.

  To check I have connected to an external monitor and managed to get again in safe mode with network, but still very bad and always red and green lines everywhere.

  I started to take a ride on the old good www and there are many posters and articles with problems and many mentioning the lines red and green etc...
  so I'm not alone, but no one seems to know exactly what it is.

  Some have mentioned the grateful Toshiba this as a problem and make even if out of warranty repairs.
  Thus, ideas, advice and does anyone know if Tosh have agreed the problem and offer any help?

  Thanks in advance

  Hello

  In my opinion, this looks like a problem of graphics card GPU eventually started to malfunction, and in this case to replace the motherboard.

  > Some mentioned Toshiba grateful that as a problem and make even if out of warranty repairs.
  Thus, ideas, advice and does anyone know if Tosh have agreed the problem and offer any help?

  It doesn't have to be dull I ve also found this update from Toshiba product support page, but there is nothing listed on the problems of F30
  http://EU.computers.Toshiba-Europe.com/innovation/generic/PRODUCT_UPDATE_SUPPORT

  What to say. Seems only a technician ASP might solve your problem, but replacing motherboard is a costly affair so it s your own decision to want to do

  In any case... good luck...

• RED and green flashing 1532 AP

  Hello

  I have a 5508 controller with internal antennas 2700 Series and external antenas. All work fine, internal APS APs green led and when someone connect turn blue.

  But with the external antenas, the led flashes green and red, I check the AP and is perfectly recheable of ping, is well recorded on WLC and have the user and EVERYTHING works fine! ...

  My question is what does flashing red and green?

  PD: the newspaper of WLC nothing shows up not bad

  Thank you

  your 2700 has enough power?

• Red/yellow/green points

  Is it possible to expand the red/yellow/green points top left? Have a client who is visually impaired. The arrow cursor to expand, but it's hard to navigate on the points - they seem pretty tiny when the user is 94. Thank you!

  Hi awwhite975,

  I understand that you want to resize the closing , minimize the , or maximize a window of buttons across all applications on Mac. your client I can give some suggestions to help out you.

  First of all, I would look to see if they use a Mac to Retina display. If they are, you should see something like the image below when you go to the System Preferences > monitors.

  

  As you can see, you will have the possibility to enlarge the text, in addition to these buttons. Take a look at the first article below who speaks with a Retina display.

  With the help of a Retina display
  https://support.Apple.com/en-us/HT202471

  Now, if they do not use a Mac of the retina, then you can simply change the resolution on a different scale. It just won't look too strong, but will accomplish what you're looking for. It is located in the same place, System Preferences > displays and you will see an option for chipped. It would be more a matter of selecting the resolution that suites your client.

  OS X Yosemite: set the resolution of your screen
  https://support.Apple.com/kb/PH19043

  The last thing you can do is allow zoom to your customer. This can create a small window which will zoom around the cursor, so they can click on one of the buttons. Take a look at the following article to go on these types of accessibility on a Mac.

  OS X Mavericks: use accessibility features
  https://support.Apple.com/kb/PH14322

  Have a great day!

• Stor.E USB HDD PX1399E - 2 20 - light continues to flash red / blue

  Stor E usb hdd, no access that passes light continues to flash red/blue, which means?
  (constant alternating red/blue 2 x / sec., and not not not flashing as read/write)

  * RESOLVED: * already tried several cables, also with dual usb (Y-cable).
  the solution was a cable with an interferencefilter close to the HARD drive.

  Post edited by: borel

  > RESOLVED: already tried several cables, also with dual usb (Y-cable).
  > solution was a cable with an interferencefilter close to the HARD drive.

  Thanks for your comments!

• 32W1333DB does not turn on - standby blinks red and green

  IV recently bought nine toshiba Led backlight LCD 32w1333db.
  can someone help tv doesn't turn on no tv or distance, standby flashes red and green...

  Thank you

  Unplug the power to the TV and wait a bit.
  Then reconnect and press the power button on the remote to power ON the TV.

  It work?

• Toshiba 40L5441DG - Led shows red and green light

  My Toshiba 40L5441DG were now waiting for 72hrs, and the Led is showing red and green lights.
  I just bought 3 weeks ago... I need help pls.

  If I understand you right when you try to turn on your TV on the LED is green, but there is no pic, right?

• My printer does not print black text, it prints in blue-green

  I recently bought a Dell all-in-one computer. When I plugged my HP Photosmart Premium all-in-One printer to the new computer, it displays only text in blue-green.  What I am doing wrong?

  HI Ms Pat 341,

  You have downloaded the appropriate on the new computer drivers? The steps, you visit the Dell support site http://support.dell.com/support/downloads/index.aspx?s=dhs&cs=19

  Once you find your printer, download the latest drivers.

  I hope this helps. Just reply to the results.

• HP Office Jet 6000 E609n Red & Blue lites flashing after installing new trolleys

  The subject little line about everything said.  After you have installed 3 new ink carts (made many times before) the ink Light Magenta and Cyan continue to Flash.  After printing a 'HP Deskjet general purpose Test-Print Page assessment', all 4 squares show own colors, perfectly informed, so I know that the ink carts are installed correctly, etc...  (Clicked in place)

  No matter what I try the lights continue to Flash.  Cannot get 'Toolbox' show, or else that could help.

  Any help appreciated.

  Thanks in advance.

  Steve

  After a lot of digging around to ask questions and even back to where the ink carts have been recently purchased, the conclusion is that the ink level monitors do not work when using reloaded ink carts. (Yes, those carts to Office Max which I forgot to mention in original post.) HP designed their carts to original ink for 'single use '. So now the printer "think" the cyan and magenta ink carts are low causing the red & blue lights flashing.

  　

  Not long after this printer was purchased in January 2010 the Toolbox stop working, even if HP carts have always been used... until now. Recently I reinstalled the HP digital imaging software and the Toolbox works again. What's weird, is that the Toolbox shows low ink on the three colors, but only the red & blue lights blink. (The black wagon is still an original HP.)

  　

  Bottom line: next time I'll pay 3 extra bucks for carts HP ink cartridges so flashing lights don't drive us crazy. LOL either that or put a piece of tape insulation on them for now.

• Video appears with red or green dots

  Original title: problem starting with Windows Vista SP2

  Hello

  I have problems with my Vista PC. It all started when I was playing a game and he hung all of a sudden. The keyboard responds No and no more than the mouse. I also noticed that there is no hard disk activity and decided to turn the PC through the AC power. The next day, I was surprised that the BIOS and Vista boot screens has red and green vertical stripes on them respectively. And after that start logo does not come out and there is also no disk activity. I tried to attempt using the Memory Diagnostic tool Windows and the Startup Repair to fix the problem, but don't have seen no improvement. However, at certain times (rare) Vista will start normally. Even if I managed to connect, if the computer is left idle the monitor turns white and move the mouse or press a key on the keyboard does not help. Please solve my problem!

  Specifications of the PC:

  Dell XPS 420 (desktop PC)

  Intel Core 2 Quad Q6600 (2.40 GHz)

  3 GB RAM

  NVIDIA GeForce 9800 GT 512 MB (version 270.61)

  Genuine Windows Vista Home Premium build 6002 SP2 x 32 with the latest updates

  Windows Experience Index: 5.5

  Hello

  colored dots and/or stripes normally relate to a graphic problem

  That's all the help I can give you

  and when you go to the Dell forums you post your question there. the same thing you are doing here

  http://en.community.Dell.com/support-forums/default.aspx

  and there join/sign in button in the upper right corner!

• Windows Movie Maker, after the problem - red and green

  When I change my movie with Windows Movie Maker preview is fine, but after the publication of the project, the film is red and green. What can I do to fix this?

  I solved this problem. But I think it was because of the video quality of my webcam. Director of Windows try to enhance the video at the time of publication. So that's my new problem. Can I update my webcam as well?

• Dotted lines of red/blue passing vertically on my photos of GoPro

  Hello

  I took a series of still images on a GB pro (black Hero3) with a Time lapse 60 sec setting.  The image size is 4000 x 3000.

  I am trying to create a time-lapse video that I did using the software suite from GoPro.  However, I have problems when you try this first Pro, as the final video does not render correctly.

  Action taken:

  1. Create the new project - accept the default settings.
  2. Click Import to start a media.
  3. Select the image and check image select.
  4. Drag the file with the framerate of 25 fps to the timeline.
  5. Click on file.
  6. Click export media.
  7. Tick match sequence settings.
  8. Click Export.

  This creates an MPEG file, but the image is distorted and has red/blue dotted lines vertically.

  

  I suspect that this is due to using the wrong sequence or codec, but don't know what should be in these settings.

  It's turned equivalent using the software of the GoPro.

  

  Any help would be appreciated!

  Thanks in advance!

  [title published by mod]

  Using El Capitan?

  First graphic question Pro?

• Red and green frames

  I work with first CS6. in my CS6-Projekt I imported an AVCDH Clip of my Panasonic HDC-TM700. An AVCHD Clip from a Canon camera, I had stabilized a color corrected and the new blocks to a H.264, HD1080i25.mp4 and also imported for my project. When I take this Clips to my timeline, I have red and green frames on my Panasonic AVCHD-original file. When I made this file I also have red a green frames in the new file.

  Why export a movie as a file and then re - import? You can always add an existing sequence in a new sequence (nesting) to make a new, less cluttered way of working. In this way made even frames red and green?