Circulation IN the NAC policies

Similar Questions

• Actual gateway IP process to strip the NAC

  Hi all

  I did a lot of research, and I can not find good answers to some of my questions. All the big questions are answered for out-of-band configuration, but I find that it is assumed that this understanding in the Strip is taken for granted lol... I guess I'm slow = P

  1. How does the gateway IP In-band real?
  2. What is the point of the 30 subnets?
  3. Are there any access/auth pairs VLAN configurations in the band?
  4. How does quarantine work?
  5. I read that the NAC server cannot send traffic on untrusted port to a VIRTUAL LAN and that you are not allowed to trunk port. This means that there is no support for several VLAN reliable, mapped to a single server at the NAC?
  6. Can you do role with configurations mapping in the band?

  Assistance for all or part of these questions would be GREATLY appreciated!

  Thank you a lot =]

  ~ Xavier.

  Hi Xavier,.

  I'll try to answer your questions

  1. How does the Strip Real-IP Gateway?

  The CASE works in routed mode, if you have different IP addresses (on different subnets) on interfaces approved and unapproved. Because the CASE does not support routing protocols, routing must be configured through static routes

  2. What is the point of the 30 subnets?

  The idea is to have small subnets for your customers so that with this config IP customers in authentication VLAN should through the CASE even to talk to other clients on the same subnet L2.

  Click here for an explanation:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/configuration_guide/47/CAs/s_dhcp.html#wp1057889

  3 is there access/auth pairs VLAN configurations in the band?

  If you ask if there is mapping VLAN, then the answer is NO, as the purpose of the VLAN mapping must * bridge * traffic between approved and unapproved mapped VLAN, but in real-IP the L3 routing traffic CASES.

  4. How does quarantine work?

  When a client is quarantined, it works the same way as OOB, as in this phase, the client is always online to the CAs.

  So the concept is assigned to the CASE by the temporary user or the role of midlife and he applies a traffic policy you've set up temporary or the role of midlife.

  5. I have read that the NAC server cannot send traffic on untrusted port to a VIRTUAL LAN and that you are not allowed to trunk port. This means that there is no support for several VLAN reliable, mapped to a single server at the NAC?

  The restriction of VLAN "single" for Real - IP CASE applies only to the * trust * side. The CASE may be the default gateway for several subnets VLAN / IP on the * rogue * side.

  Configuring addresses VLAN / additional IP on the unreliable side by using the configuration "managed subnet.

  This is mentioned here:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/configuration_guide/45/CAs/s_deploy.html#wp1050938

  The clean access server can manage one or more subnets, with its untrusted interface, acting as a gateway for managed subnets. For more information on the setup of managed subnets, see Configuring managed subnets or static routes page 5-26.

  6. can you do role with configurations mapping in the band?

  Yes, you can do it! However, you cannot assign a VLAN as you do in OOB, but you can assign the different level of access based on IP traffic strategies and bandwidth restrictions that you assign the specific role.

  For example, check here for more details:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/configuration_guide/45/cam/m_users.html#wp1040231

  In a Word, regardless of the use of the band vs OutOfBand:

  -customers are InBand before CAs in CASE detection, authentication, the phases of assessment and remediation of posture.

  The main difference occurs when the user is allowed to access the network and that you run the IB role assignment and OOB but... :

  -in customer traffic keeps on inline flowing to the IB CAs, so you can apply different access policies (ACL) and control of bandwidth depending on the role policies (but you cannot assign a VLAN);

  -in OOB, customer traffic bypasses the CASE once it is authorized: in this case, you can apply different VLAN but (given that the CASE is no longer along the way) you cannot apply ACL and/or ensuring the policy in this case.

  I hope that answers your questions.

  Kind regards

  Federico

  --
  If this answers your question please mark the question as "answered" and write it down, so other users can easily find it.

• Logic and rules of the NAC

  I have a question about WINXP rules in the NAC server and more specifically, if a rule reports a failure, but it's part of a! the rule, this means - happening?  For example:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  &(!pc_Windows_ehkeyctl|pc_XP_MCE_KB973768_MS09-037) (red indicates failure)

  The NAC is reported as a check failed:

  pc_Windows_ehkeyctl, File Check [$SYSTEM_ROOT\ehome\ehkeyctl.dll is]

  It is a failure because it finds the file and there is a negative on the rule?

  What about this:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  &(!pc_XP_2115168_MS10-052_FileChk|pc_XP_2115168_MS10-052)

  The first part of the reports as passage, and the second reports failure... but logically, this part of the rule must pass because only after the first part?  Which apparently correct?

  Thank you!

  Gavin - Budd

  He actually reports a failure audit - and in many cases, it is expected (and confusing!).  For example, with Windows controls preconfigured, if it is a 32-bit client you will see fail the verification of 64-bit.

  Same with your second example check

  &(!pc_XP_2115168_MS10-052_FileChk|pc_XP_2115168_MS10-052)

  We expect that it is not the first cheque or spend the second control - but one of these controls will show as failed.  Clear as mud?

• I'm having a holiday in Nha Trang, Viet Nam and my stolen obtained iphone6 10:00-22:30 last night, I activated lost mode which is still pending and said the local police. What should I do?

  I'm having a holiday in Nha Trang, Viet Nam and my iphone6 who was in my bag got stolen 10:00-22:30 last night while returning to the hotel, I activated lost mode which is still pending and said the local police. find my iPhone is in offline mode. What should I do? I read online that if I erase all my data can find that my iphone will be more capable. I also read online that the stolen iphone can be replaced? What should I do? I can't fnd an e-mail to contact apple Australia I did purchase in Sydney Australia.

  Please help me.

  There is nothing for you to do.

  What to do if your iDevice is lost or stolen

  iPhone, iPod Touch and iPad

  If enable you find my phone before it was lost or stolen, you can follow only if it is connected to the Internet by Wi - Fi or cellular. What you can't do, is follow your device using a serial number or other identification number. You can't wait for Apple or anyone else to find your device for you. You can't recover your loss unless you make your device for the loss. It is not covered by your warranty.

  If your iPhone, iPod, iPod Touch, or iPad is lost or stolen, what do you do? There are things you should have done in advance - until you have lost it or it has been stolen - and things to do after the fact. Here are a few suggestions:

  This link, Re: help! I misplaced / lost my iPhone 5 today morning at delta Chelsea hotel downtown one I am not able to follow. Please help!, has some good advice about your options when your iDevice is lost or stolen.

  1. declaration of a lost or stolen Apple product

  2 find my lost iPod Touch

  3. AT & t. Sprint and Verizon can block phones stolen/tablets

  4. What-To-Do-When-Iphone-Is-Stolen

  5. use ICloud Mode lost

  6. what to do if your iOS device is lost or stolen

  7 6 ways to track and recover your lost/stolen iPhone

  8. find my iPhone

  9 report Stolen iPad | Stolen lost found online

  It pays to be proactive in following the advice on the use of find my phone before you lose your device:

  1. find my iPhone

  2 set up your iDevice oniCloud

  3. OS X Lion/Mountain Lion - in regard to my Mac

  4 the free configuration find your iPhone (even on unsupporteddevices)

• How can I send the snowdrift police to my brother

  How can I send the snowdrift police to my brother

  It comes in a zip file that you can attach it to an email. Or, simply let him download itself.
  http://www.xmasfonts.com/details/snowdrift.html

• Version of the NAC

  Dear,

  Can what version of the NAC I install VMware?

  Can anyone help please with the above query.

  Thank you

  NAC is not supported on Vmware. Yet people have managed to install NAC4.1 on Vmware, but newer version do not work.

  There is a new product called Cisco ISE, which will eventually replace the NAC. Cisco ISE can be installed on Vmware.

• Ports of the NAC

  Hello Experts,

  Have some questions that came across while doing work of the NAC at one of our subsidiaries. If there is some user ports which are not selected for the profile of the NAC, is it possible (except physical control on the cell phone of the user by allowing all ports & audit) which can be used to track the paths of users without mail for NAC.

  Second, if the user of the NAC port is manually on the vlan user (rather than quarantine or vlan temporary), which is the correct order for that.

  the user on NAC field must be typed manually to vlan user or port profile should try not controlled followed by rebound port & update.

  Apprecite all help, thank you.

  Hello

  See online:

  If there is some user ports which are not selected for the profile of the NAC, is it possible (except physical control on the cell phone of the user by allowing all ports & audit) which can be used to track the paths of users without mail for NAC.

  [Tiago] On the graphical interface of CAM, you can check which controlled uncontrolled ports are. It is the only place where ports can be determined to be managed/no managed.

  Second, if the user of the NAC port is manually on the vlan user (rather than quarantine or vlan temporary), which is the correct order for that.

  the user on NAC field must be typed manually to vlan user or port profile should try not controlled followed by rebound port & update.

  [Tiago] When you perform the configuration of the switch, the switchports can be put on the vlan user or default access vlan. It depends on the port profile settings that you have configured. By default, when a port is managed on the basis, if a client connects, an SNMP trap is sent to the CAM. The CAM check whether the machine is certified or not (check the mac address). If the machine is not certified cam becomes the vlan the authenticated vlan configured on the port profile.

  So, whenever you connect a PC to a switchport, CAM evaluates what is the vlan correct the PC to start and change it accordingly.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Support of the NAC Profiler address & ip

  Hello

  I have a layer 3 OOB NAC Profiler deployment and I am trying Profiler some IP phones from a remote location by using the statement of helper-ip address on the interface on the remote router. The problem is that the remote router acts as a dhcp server for the vlan voice and fact not forword DHCP discover for Colectionneurs of the NAC, and I can't phone ip profile. Do you know a way (an order of configuration on the router) to forword the dhcp even though the router acts as a DHCP server for this vlan?

  Thank you

  Victor

  Hi Victor,

  To do this... You must add a SVI for the voice VLAN on the switch behind the router, and then add the IP helper on the new interface VLAN voice.

  -Hassan

• Fight against exclusion the NAC mac

  Experts, assuming that few users are now authenticate & viz cisco NAC network access, they be filtered from the NAC to exclude the posture of NAC will be they be disconnected from the network & reconnected since they were connected & now are going to be ignorant of the NAC.

  How it works in this case. users will be disconnected for that to be effective, or will they be disconnected by force before it takes effect.

  Thanks to you all.

  Hello

  There is a port bouncing feature Cisco NAC that accomplishes this task for you. But it depends on your deployment mode, it is not required for each of them. Please see this link:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/configuration_guide/48/cam/m_oob.html

  Please indicate if you will find the entrance helpul. Thank you

  Farrukh

• Activation of the NAC HA puts several hosts and ASA with processor clocked at 100%

  I installed a NAC Manager and a NAC server in OOB without any problems, but when I configured the AP (high availability) with another server, my ASA and several guests in my network started work ant 100% of the cpu.

  I tried to configure each interface of the NAC on a single DMZ and the problem stops there.

  -That someone had this problem (NAC version 4.7)

  TKX

  Miguel Amaral

  Hello Miguel.

  When I started a NAC InBand HA solution I had a similar problem that I solved the heart rate HA configuration to use ETH0 just instead use ETH0 and ETH1.

  Best regards

  Luciano Carvalho

• Upgrade the NAC of 4.5 to 4.8

  Hello everyone

  I'm about to upgrade to a CNA of 4.5 to 4.8 on an application I do in a bank with 1500 users. The upgrade is due because the Bank makes its migration from PC to Windows 7

  The implementation is in a failover situation (2) and (2) CAM. the design is Out of Band, a virtual gateway and integration with a wireless LAN controller.

  I would like to know if when I upgrade the CAM and CAS´s for version 4.8 can I still use the Agent access own version 4.5 on clients? To perform the migration in several steps

  There is a StubAgent for version 4.8? or already included in the Agent 4.8? I install the StubAgent on all computers of the Bank, because they have no administrative rights.

  What is the best way to perform the upgrade of agents which does not affect users?

  Thanks in advance

  Eduardo Navas

  Hi Eduardo,

  Agent 4.5 is compatible with 4.8 CAM/CASE, although with a few restrictions:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/support_guide/agntsprt.html#wp52084

  For example, see also the following notes:

  "If you use version 4.8 of CAM/CASES with a version of the Agent plus early 4.8.0.32, then either use the requirement of the Distribution link or upgrade the Agent to the latest version to use the Distribution of files".

  "Cisco NAC Agent version 4.5.x is not supported by download version 4.6 (1) CAM because the structure of Agent installation files is different in version 4.5 (x) compared to the support in version 4.6 (1) agents."

  The NAC 4.8 agent has not any component necessary as the previous stub, for example:

  http://www.Cisco.com/en/us/docs/security/NAC/appliance/configuration_guide/48/cam/m_webagt.html#wp1473153

  Kind regards

  Fede

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Integration of the NAC Profiler - cannot add list of filters on cam

  Hi all

  I have a problem with the Profiler - integration of the NAC for endpoint profiling.

  Here's the situation:

  I have already created the integration based on the steps in the Guide: Setup Cisco NAC Appliance integration. I think that the configuration is correct, because I can do database synchronization between the Profiler and CAM. Here's the log of server profile:

  NAC_SYNC: Task_Queue_Runner commissioning
  NAC_SYNC: Profiler / END of synchronization of the NAC [add 0, upd 0, desc 0, rm 0]
  NAC_SYNC: Profiler / START the synchronization of the NAC
  INFO: [2010-12-15 11:01:09 (fcapGetHWAddr:49)] is for eth0 MAC

  I have already created a profile of endpoint named "Admin" which is based on the IP address. I also created the NAC events based on endpoint profile 'Admin '.

  The event of the NAC will present 'Admin' profile to a role of the NAC. This event aims to circumvent 'Admin' of the legalisation of the ANC visa so that the "Admin" can connect to the network automatically to a role of the NAC.

  However, when 'Admin' to connect to the network, it still is challanged by NAC. I don't see "Admin" on the filter of the CAM or the list.

  This means that the endpoint profiling is still broken.

  Is there anyone who have experience with this?

  Thanks for the support and comments

  Imad

  Hello

  You cannot add devices manually on the profiler.

  The Profiler has to detect automatically (it is the concept of profiling).

  How this Profiler detects endpoints use the modules of collector.

  Each module has endpoints detection means.

  You will find the description of each collector module here:

  http://www.cisco.com/en/US/docs/security/nac/profiler/configuration_guide/311/p_intro231.html#wp1062345.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• In the NAC MAC address filter list

  How are Faisal Hi, you? I have a question about this list of filters in the unit of the NAC. I want to do those recognized unit of the NAC mac addresses are to be get the network. However if a workstation's mac address is not in the filter list, would it not able to do the network. Is that the NAC has the ability to do? Please let me know. Thank you.

  Richard

  I'm not Faisal, but...

  You want to make additional (such as LDAP or such) or any authentication simply based on the MAC address?  If you want to only via the MAC, you can add them to the list of filters and then either set to 'allow' to allow all traffic, 'role' to put them in a specific role, or "check" to apply the evaluation of posture and then put them in the role.  If no other server authentication is configured, users who were not in the list of filters would not be able to authenticate, and they would be stuck in the authenticated VLAN.

  Thank you

  Lauren

• Configuration of the switch of the NAC

  Hello!!

  I bought a NAC server and a manager of the NAC, to centrally manage the vlan where users connect to based on authentication.

  I have several sites, but the NAC server will be at Headquarters.

  When a remote user authenticates, NAC must configure the user switch port for the vlan right.

  What is an out-of-band solution?

  Do need me a specific license for out-of-band?

  Best of look,

  Miguel Amaral

  Hello

  It's the same pattern: Yo uneed 2 licenses, one for the CAM and the other for CAs.

  One cam sets the number of cases you can add.

  That case defines how many users is supported.

  So either the CASE PAK has been lost, or never bought.

  In both cases, you will need to contact the entitiy that sold devices and demand for the PAK CASE.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Profiler in the NAC 2.1 to 3.1 upgrade

  Hi guys,.

  I'm setting up a Profiler from the NAC that accompanies 2.1 installed. I upgraded to 3.1, prayed and installed the license without any problems, but I always get this message: "ERROR: [2010-12-08 09:25:01 (main: 668)] valid no key not found [no such file or directory]" "

  The license file exists, and on the interface Web Profiler from the NAC, the State of the license is OK.

  A single line in the license file gives me this information: 'cisco 2.1 INCREMENT CCA-MANAGER countless Permanent '.

  Does anyone know if the license is linked with the version of Profiler?

  The upgrade from 2.1 to 3.1 is allowed or it is necessary to purchase a new license 3.1?

  Best regards

  Hello

  So I guess you spotted the problem here...

  You have a collector's license?

  You need 2 licenses: 1 to the server profile, and one for the collector.

  Basically, the mac address you provide is the same (eth0 ot Server Profiler), but you need a PAK Server Profiler to generate the license Server Profiler (the one you already have) and a PAK for license collector (which is missing).

  You have the collector PAK?

  If Yes, then just go to the license page and submit this PAK and the mac address.

  HTH,
  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.