Cisco 1220 series b AP

a cisco AP1220B series will support wpa2?

Hi William,.

My understanding is that the AP1220b was released prior to the adoption of the WPA2 and does not support.

Sorry man!

Rob

Tags: Cisco Wireless

Similar Questions

-Adding memory for Cisco 7200 Series hardware

Can anyone help point me to any document from Cisco on the addition of memory SDRAM and Flash in the Cisco 7200 series routers?

Thanks in advance.

DTA

Does that help?

http://www.Cisco.com/en/us/products/HW/routers/PS341/products_installation_guide_book09186a00800f0371.html

Cisco 1602i series Access point installation

Hello everyone. I tried to configure cisco AIR-CAP1602i-E-K9 series access point is default for the configuration files and other settings, I guess you are looking for WLC. but I do not have a WLC I want to configure the AP a standalone conceerne Access point. I connected via switch where all the ports on the switch are vlan 10 switch is connected to a router and I have configured the router as DHCP server. It is my first time that I've never touched a cisco point for configuration of access. below is the error that was coming up on the screen countinously when I access the AP via the console. Kindly any assistance in this regard would be highly appreciated. Thank you

* 00:18:46.324 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
Not in a bound State.
* 00:19:31.824 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
* 00:19:36.828 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
* 00:19:36.948 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.218, mask 255.255.255.0, hostname AP64f6.9dee.87d1

Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:19:42.824 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

* 00:19:51.823 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
Not in a bound State.
* 00:20:37.323 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
* 00:20:42.327 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
* 00:20:42.447 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.219, mask 255.255.255.0, hostname AP64f6.9dee.87d1

Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:20:48.323 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

* 00:20:57.323 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
Not in a bound State.
* 00:21:42.822 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
* 00:21:47.826 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
* 00:21:47.946 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.220, mask 255.255.255.0, hostname AP64f6.9dee.87d1

Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:21:53.822 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

* 00:22:02.822 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
Not in a bound State.
* 00:22:48.322 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
* 00:22:53.326 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
* 00:22:53.446 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.221, mask 255.255.255.0, hostname AP64f6.9dee.87d1

Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:22:59.322 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

* 00:23:08.322 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
Not in a bound State.
* 00:23:53.821 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
* 00:23:58.825 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
* 00:23:58.945 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.222, mask 255.255.255.0, hostname AP64f6.9dee.87d1

Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)

If you do not have WLC, you will need to convert this access point in stand-alone mode. See below on this post. You must required image before this conversion. If you have a support contract with Cisco you can download from Cisco.com

https://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

https://mrncciew.com/2013/12/13/AP-conversion-using-mode-button/

HTH

Rasika

Pls note all useful responses *.

Question of the router Cisco RV series

Hello

I have a question. We sell a lot of cisco 800 routers. Now for some clients, we have that they are expensive.

Then we thought about the RV series, but I can't find any good routing performance for these routers specifications.

If I go to:

http://www.Cisco.com/Web/partners/downloads/765/tools/quickreference/routerperformance.PDF

I see a lot of details of the cisco product, but the RV series isn't here.

Can someone tell me what are the specifications of performance of these routers? (packets per second, Mbit/s data rate)

Thanks in advance,

Tom

You can also access the data at smallnetbuilder. There are many different performance tests

http://www.SmallNetBuilder.com/lanwan/router-charts/view

Trouble getting a Cisco 2600 series AP to stay connected to WLC 5508

Hello

I recently loaded the independent our old APs upgrade to LWAPs. We have a WLC 5508 to our Virtual Co - Lo and I use Flexconnect to accommodate local switch and dhcp on our sites. I have updated more than 50 APs and joined them to the controller. These include only the 1130AG and 1240AG models. However they work perfectly and stay connected to the controller. I'm having is with a new batch of 2600 series APs stay connected to the controller. I tried to do research in what may cause disconnect it but have yet to find a solution. I use DNS to resolve queries for CAPWAP & LWAPP APs to the controller on our EXTENSIVE network. Read other messages I thought that this is perhaps a problem with packages to drop but have had our provider that manages Sonicwalls at both ends of the WAN confirm for me that there is no packet loss. Here are the logs that I collected through the puttty of the WLC & AP. Any help would be greatly appreciated.

AP, I do the test on:

NAME: "AP2600', DESCR: 'Cisco Aironet 2600 Series (IEEE 802.11n) Access Point.

PID: AIR-CAP2602I-A-K9, VID: V01, SN: FTX1740J8V1

WLC in question:

Name of the manufacturer... Cisco Systems Inc..

Product name... Cisco controller

Version of the product... 7.3.112.0

Bootloader Version... 1.0.1

Retrieving Image Version field... 6.0.182.0

Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27

Build Type....................................... DATA + WPS

System name... wificontroller

Location of the system... Corp

Contact System... Net engineer

ObjectID of system... 1.3.6.1.4.1.9.1.1069

Redundancy mode... People with disabilities

IP Address....................................... 10.250.32.8

Last Reset....................................... Software reset

Time system... 190 days 3 hours 34 minutes 24 seconds

Location of the time zone of the system... (GMT - 5:00) Eastern (USA and Canada)

The country is set... USA - United States

Operating environment... Utilities (0 to 40 ° C)

Limits the internal temperature alarm... 0 to 65 ° C

-Other - or ITU (q)

... Internal temperature 38 C

Outdoor temperature... + 20 C

Fan Status....................................... Ok

State of 802. 11 b network... Activated

State of 802. 11A network... Activated

Number of wireless LANs... 14

Number of Active Clients... 71

Built-in MAC address... C8:9 C: D: 8 1: 52:E0

Power supply 1... Currently, OK

Power supply 2... Absent

Maximum number of taken access points supported... 100

Here is the result which leaves on concluded that the AP joins the WLC for a short period and then goes offline

WT-4thFlr-AP3 #.

* 15:42:04.419 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST

., 3)

* 15:42:11.443 Dec 14: EVT-4-AVT %: write flash: / done event.capwap

* 15:42:11.483 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode

* 15:42:11.487 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION

* 15:42:11.487 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246

* 15:42:11.571 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.

* 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).

* 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller

* 15:42:12.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246

* 15:42:14.303 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246

* 15:42:14.303 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8

* 15:42:15.127 Dec 14: "Promiscuous" from Ethernet mode

* 15:42:15.535 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP

* 15:42:15.667 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1

* 15:42:15.667 Dec 14: AC setting hop first MAC: 0017.c575.a23c

* 15:42:15.855 Dec 14: % CAPWAP-5-JOINEDCONTROLLER: AP joined controller wificontroller

* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file

* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file

* 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: map No. LS Flex to load ACL configuration file. To connect to the controller to get the configuration file

* 15:42:15.915 Dec 14: LWAPP-4-CLIENTEVENTLOG %: no central Dhcp configuration file map to load. To connect to the controller to get the configuration file

* 15:42:15.915 Dec 14: % LWAPP-3-CLIENTERRORLOG: connected mode

* 15:42:23.639 Dec 14: FEDS-6-ACTIVATED %: Signature of IDS is loaded and enabled

* 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 0 disabled

* 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 1 disabled

* 15:45:43.783 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST

(. 11).

* 15:45:43.787 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode

* 15:45:43.787 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION

* 15:45:43.787 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246

* 15:45:43.867 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.

* 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).

* 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller

* 15:45:44.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246

* 15:45:46.315 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246

* 15:45:46.315 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8

* 15:45:46.487 Dec 14: "Promiscuous" from Ethernet mode

* 15:45:49.903 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP

* 15:45:50.031 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1

* 15:45:50.031 Dec 14: AC setting hop first MAC: 0017.c575.a23c

Here are the results of the client debugging capwap event about to access:

WT-4thFlr-AP3 #debug capwap customer event

Display debugging EVENT customer CAPWAP is on

WT-4thFlr-AP3 #.

* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

* 15:55:08.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:08 UTC 14 December 2013

* 15:55:25.579 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:55:25.587 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

* 15:55:25.827 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:55:25.835 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

* 15:55:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:56 UTC 14 December 2013

* 15:56:25.735 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:56:25.743 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

* 15:56:25.983 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:56:25.991 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

* 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

* 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

* 15:56:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:56:56 UTC 14 December 2013

Here are the results of debug capwap client package in detail:

WT-4thFlr-AP3 #.

* 14 Dec 15:59:01.823: <   start="" of="" capwap="" packet ="">>

* 15:59:01.823 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:01.823 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST

* 15:59:01.823 Dec 14: Msg length: 0

* 15:59:01.823 Dec 14: Msg SeqNum: 44

* 14 Dec 15:59:01.823: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:01.831: <   start="" of="" capwap="" packet ="">>

* 15:59:01.831 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:01.831 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:01.831 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE

* 15:59:01.831 Dec 14: Msg length: 15

* 15:59:01.831 Dec 14: Msg SeqNum: 44

* 15:59:01.831 Dec 14:

* 15:59:01.831 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11

* 15:59:01.831 Dec 14: the vendor identifier: 0 x 00409600

* 15:59:01.831 Dec 14:

* 15:59:01.831 Dec 14:

IE: UNKNOWN IT IS ABOUT 151

* 15:59:01.831 Dec 14: IE length: 5

* 15:59:01.831 Dec 14: decode the routine unavailable, Hex Dump printing

* 15:59:01.831 Dec 14:

52 80 46 00 AC

* 14 Dec 15:59:01.831: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:20.931: <   start="" of="" capwap="" packet ="">>

* 15:59:20.931 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:20.931 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

* 15:59:20.931 Dec 14: Msg length: 93

* 15:59:20.931 Dec 14: Msg SeqNum: 38

* 15:59:20.931 Dec 14:

* 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 89

* 15:59:20.931 Dec 14: the vendor identifier: 0 x 00409600

* 15:59:20.931 Dec 14:

* 15:59:20.931 Dec 14:

IE: RRM_NEIGHBOR_CTRL_PAYLOAD

* 15:59:20.931 Dec 14: IE length: 83

* 15:59:20.931 Dec 14: decode the routine unavailable, Hex Dump printing

* 15:59:20.931 Dec 14:

00 0 HAS FA 20 08 01 00 07 0A 20 08 03 00 01 FA F4

01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7

22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F

53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00

00 00 00 00 00 00 00 00 00 00 00 00 00 01 06 0B

01 01 01

* 14 Dec 15:59:20.931: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:20.931: <   start="" of="" capwap="" packet ="">>

* 15:59:20.931 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

* 15:59:20.931 Dec 14: Msg length: 8

* 15:59:20.931 Dec 14: Msg SeqNum: 38

* 15:59:20.931 Dec 14:

* 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

* 15:59:20.931 Dec 14: result of Code: CAPWAP_SUCCESS

* 14 Dec 15:59:20.931: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:21.139: <   start="" of="" capwap="" packet ="">>

* 15:59:21.139 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:21.139 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:21.139 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

* 15:59:21.139 Dec 14: Msg length: 111

* 15:59:21.139 Dec 14: Msg SeqNum: 39

* 15:59:21.139 Dec 14:

* 15:59:21.139 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 107

* 15:59:21.139 Dec 14: the vendor identifier: 0 x 00409600

* 15:59:21.139 Dec 14:

* 15:59:21.139 Dec 14:

IE: RRM_NEIGHBOR_CTRL_PAYLOAD

* 15:59:21.139 Dec 14: IE length: 101

* 15:59:21.139 Dec 14: decode the routine unavailable, Hex Dump printing

* 15:59:21.143 Dec 14:

01 0 TO FA 20 08 01 F4 00 07 0A 20 08 00 01 0C FA

01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7

22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F

53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00

00 00 00 00 00 00 00 00 00 00 00 00 00 24 28 2

30 34 38 3 40 95 99 9 01 01 01 01 01 01 01 A1

01 01 01 01 01

* 14 Dec 15:59:21.143: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:21.143: <   start="" of="" capwap="" packet ="">>

* 15:59:21.143 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:21.143 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

* 15:59:21.143 Dec 14: Msg length: 8

* 15:59:21.143 Dec 14: Msg SeqNum: 39

* 15:59:21.143 Dec 14:

* 15:59:21.143 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

* 15:59:21.143 Dec 14: result of Code: CAPWAP_SUCCESS

* 14 Dec 15:59:21.143: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:25.547: <   start="" of="" capwap="" packet ="">>

* 15:59:25.547 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:25.547 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST

* 15:59:25.547 Dec 14: Msg length: 14

* 15:59:25.547 Dec 14: Msg SeqNum: 45

* 15:59:25.547 Dec 14:

* 15:59:25.547 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10

* 15:59:25.547 Dec 14: the vendor identifier: 0 x 00409600

* 15:59:25.547 Dec 14:

* 15:59:25.547 Dec 14:

IE: RRM_LOAD_DATA_PAYLOAD

* 15:59:25.547 Dec 14: IE length: 4

* 14 Dec 15:59:25.547: slot ccaLoad 0 rxLoad 0 txLoad 0 33

* 14 Dec 15:59:25.547: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:25.555: <   start="" of="" capwap="" packet ="">>

* 15:59:25.555 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:25.555 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:25.555 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

* 15:59:25.555 Dec 14: Msg length: 0

* 15:59:25.555 Dec 14: Msg SeqNum: 45

* 14 Dec 15:59:25.555: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:25.795: <   start="" of="" capwap="" packet ="">>

* 15:59:25.795 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:25.795 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST

* 15:59:25.795 Dec 14: Msg length: 14

* 15:59:25.795 Dec 14: Msg SeqNum: 46

* 15:59:25.795 Dec 14:

* 15:59:25.795 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10

* 15:59:25.795 Dec 14: the vendor identifier: 0 x 00409600

* 15:59:25.795 Dec 14:

* 15:59:25.795 Dec 14:

IE: RRM_LOAD_DATA_PAYLOAD

* 15:59:25.795 Dec 14: IE length: 4

* 14 Dec 15:59:25.795: slot ccaLoad 1 rxLoad 0 txLoad 0 0

* 14 Dec 15:59:25.795: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:25.803: <   start="" of="" capwap="" packet ="">>

* 15:59:25.803 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:25.803 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:25.803 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

* 15:59:25.803 Dec 14: Msg length: 0

* 15:59:25.803 Dec 14: Msg SeqNum: 46

* 14 Dec 15:59:25.803: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:30.375: <   start="" of="" capwap="" packet ="">>

* 15:59:30.375 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:30.375 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

* 15:59:30.375 Dec 14: Msg length: 17

* 15:59:30.375 Dec 14: Msg SeqNum: 40

* 15:59:30.375 Dec 14:

* 15:59:30.375 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 13

* 15:59:30.375 Dec 14: the vendor identifier: 0 x 00409600

SlotId: 0

Mobile Mac Addr: BC:52:B7:E3:17:CB

* 14 Dec 15:59:30.375: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:30.375: <   start="" of="" capwap="" packet ="">>

* 15:59:30.375 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

* 15:59:30.379 Dec 14: Msg length: 8

* 15:59:30.379 Dec 14: Msg SeqNum: 40

* 15:59:30.379 Dec 14:

* 15:59:30.379 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

* 15:59:30.379 Dec 14: result of Code: CAPWAP_SUCCESS

* 14 Dec 15:59:30.379: < end="" of="" capwap="" packet ="">>

* 14 Dec 15:59:30.387: <   start="" of="" capwap="" packet ="">>

* 15:59:30.387 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 15:59:30.387 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 15:59:30.387 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

* 15:59:30.387 Dec 14: Msg length: 0

* 15:59:30.387 Dec 14: Msg SeqNum: 47

* 14 Dec 15:59:30.387: < end="" of="" capwap="" packet ="">>

* 14 Dec 16:00:00.387: <   start="" of="" capwap="" packet ="">>

* 16:00:00.387 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

* 16:00:00.387 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST

* 16:00:00.387 Dec 14: Msg length: 0

* 16:00:00.387 Dec 14: Msg SeqNum: 48

* 14 Dec 16:00:00.387: < end="" of="" capwap="" packet ="">>

* 14 Dec 16:00:00.395: <   start="" of="" capwap="" packet ="">>

* 16:00:00.395 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

* 16:00:00.395 Dec 14: HLEN 2, Radio ID 0, WBID 1

* 16:00:00.395 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE

* 16:00:00.395 Dec 14: Msg length: 15

* 16:00:00.395 Dec 14: Msg SeqNum: 48

* 16:00:00.395 Dec 14:

* 16:00:00.395 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11

* 16:00:00.395 Dec 14: the vendor identifier: 0 x 00409600

* 16:00:00.395 Dec 14:

* 16:00:00.395 Dec 14:

IE: UNKNOWN IT IS ABOUT 151

* 16:00:00.395 Dec 14: IE length: 5

* 16:00:00.395 Dec 14: decode the routine unavailable, Hex Dump printing

* 16:00:00.395 Dec 14:

52 80 81 00 AC

* 14 Dec 16:00:00.395: < end="" of="" capwap="" packet ="">>

Try reducing the mtu on ap 2600.

Cannot complete Set Up resettlement Officejet 6450 with Mac and N Cisco router series

I have been using - no problem - my printer wireless HP Officejet J6450 with my Mac OS X Snow Leopard. Months later, I upgraded my Mac to Lion.

Recently died my router (Netgear G series) and we had to install and to set up a new-(series N Cisco). Now, I am unable to complete the Set Up for my HP printer. Everything is fine until I get to the final installation and it says unable to complete.

I have been dedicated to support Apple and update of my Mac, hoping their work around go possible, but to no avail. Grateful for the help! Thank you!

I got it, I got it, I got it!

The last whim, it's that I didn't know that I had to install the network on the printer! Once I did and ran the setup of the new wizard it worked! You helped make my WEEEEEKKK! Thank you so much. Wish I could give you 200 Kudos. I would!

Cisco 1200 Series AP - expand the network?

Hello

I have a Cisco AP's 1200 and there are 2 rooms in my house where I do not have enough reception.

Can I use something like a Repeater or a bridge? I have active encryption LEAP.

Thanks for your help,

Concerning

Bottom

Not exactly - the second access point in your case would be configured as a Repeater, so nothing would be connected to it except the power cord. It is tuned for the AP main reason for which the flow of this AP will be half of the regular AP among other things.

What I would do if I were you (because I don't like repeaters) is buy a linksys router and plug the modem cable on it.

This does two things - you have now the possibility to create a network internal behind this 'physical firewall' using the NAT translation. You have also 4 ports that you can plug stuff in to share a connection.

So, you plug the two AP in the linksys box and now you have two RF cells that provide flow high with out having to repeat.

The drawback here is to get a cable to the furthest AP.

The result is the AP do not have to be next to the cable box and you can now location in more desirable places around your home to maximize coverage without sacraficing flow.

The added benefit to protect your data from queries ping not allowed and do'ers wrong trying to pop locks easy.

see the "shields up" pages on www.grc.com who will explain better than I probably...

Shutdown order to Cisco TelePresence-series C API:

Hi all

I'm looking for a PLC control this codec decision. I checked the C API TC4 and TC5 series for control of such but I wasn't able to find it.

All the world knows the command shutdown the codec?

Thank you!

Hello

In the operative part of the judgment, I found a single command on TC5.1, do not verified the TC4

xcommand priming Action: stop

You can try this command in the operative part of the judgment.

Kind regards

Vivek

Cisco 1900 series ssl vpn license

Hello

Since the FL-SSLVPN10-K9 license cannot be purchased, I wonder what are the options on my router CISCO1921-SEC/K9 should I now if I want to use SSL VPN, if any?

Thanks in advance

Kind regards

Herman

I think the best way is to allow the new AnyConnect 4 which is also valid for the IOS-based VPN gateways:

http://www.Cisco.com/c/dam/en/us/products/security/AnyConnect-og.PDF

Cisco profile series - vs vs C40 C20 C60 codec

Hi people,

Is there an online guide that can give me some information about comparisons between codecs c20, c40 and c60 on video profile 42 series systems and why it has such a big difference in the price that is, what have you found to this extra cost?

Also, is it possible to connect an external projector codec to view the video of the codec on the overhead?

Thank you

Hello.

Yes, it will be possible. You have several inputs and outputs on different codecs.

The main difference between the C series are physiqueet inputs and outputs and call functions. See the tables below.

Models top means more inputs and outputs.

There are more features than this, but the list shows key capabilities

	C20	C40	C60	C90

Resolution	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
End to end	720p30 +.	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
End to end double-flow	p15 1280/768	1280 × 768 p 30	1600 x 1200 30 / 1080 p 30	1600 x 1200 30 / 1080 p 30
Output and input physical
Mic input	2 mini jacks	2 XLR	4 XLR	8 XLR
Video in	1 + 1 DVI HDMI	2 + 1 DVI HDMI	2 + 2 DVI HDMI	4 HDMI + DVI 2
		1 S - video / Comp	1 S - video / Comp	HD - SDI 4 component 2
				1 comp / S-Video
Video output	2 HDMI	1 + 1 DVI HDMI	1 HDMI + 1 DVI + Comp	2HDMI + 2 DVI + Comp
MultiSite	NO.	4 way	4 way	4 way
Resolution

576 p 30 720 p 30 1080 p 30/720 p 60 Other API API API GPIO GPIO Processing power

Thank you

Marius

block websites Web of Cisco 800 series Router

Hello

I have a Cisco router running. I want to block certain websites (facebook, twitter, etc.) and download files with extensions such as

*.AVI, *.mp3, *.mp4, *.exe, *.wma, *.wmv and *.torrent etc...

I want to block for some users (based on the MAC address) and allow other users to have access to it on the same network.

Help me to do this?

Here's what you do:

IP block ip extended access list

allow an ip

permit tcp host 192.168.0.100 any eq www

permit tcp host 192.168.0.107 any eq www

I suggested to do the following:

IP block ip extended access list

permit tcp host 192.168.0.100 any eq www

permit tcp host 192.168.0.107 any eq www

Can't you see the difference?

Concerning

Alain

Remember messages useful rate.

Cisco C, series SX TC6.2 Programmable buttons programmable appeal reserved by system

After the TC6.2, I noticed that all 4 first slots for the mode of APPEAL programmable programmable buttons are now reserved by the system.

The user guide on the other hand always details that all five of them should be available.

No explanation by Cisco engineers why this is so?

Thank you and best wishes,

Mihail

Hello

I think that you have a multiway configured in your system. In this mode, the buttons are reserved for functions such as hold, RESUME, fusion, new calls.

This was as it's been for multiway is introduced, not only TC6.2 version.

Concerning

Cisco 6500 Series install w / sup

Hello

I am new to this forum and have been assigned to a project to make a "provisional" for a few Cisco management frameworks installation 6509, 6504, 6513 and 6500 all with SUP32. I've only used before independent Cisco Catalyst switches so this is all new to me. Everything I do is assign an IP address for another team can access it remotely to make customizations/configurations.

I tried to do some research to find a bit of a tutorial or installation guide to make these small configurations. Cisco is reluctant to disclose information on these topics. Or am I looking in the wrong place. As I said, all I have to do is assign and IP of the device, so it can be accessed remotely, so it is a simple configuration (or we could think of it) but my experience of Cisco is limited.

If anyone can help me with this it would be greatly appreciated. Here is a list of the equipment, I will install more in detail.
- Cisco 6509 w / SUP32GE-3 b
- Cisco 6504 w / SUP3210GE-3 b
- Cisco 6513 w / SUP32GE-3 b
Any information or direction would be great! Thank you!

Excellent. This should be very easy for you. When you receive the text file, look at the first two lines. They should read:

Enable

config t

Then the rest of the config. The reason why these two 1 lines are important is because 'activate' you will get to the exec mode, "config t" you will get to setting mode and if there is a switch out-of-the-box, it will be the only way to get into configuration mode. If these 2 lines starts the text file, just bring up the switch, and when you see the "switch > ' prompt, copy/paste the contents of the text file directly to the console session." If these two lines are missing since the beginning of the text file, all you have to do to get to a mode configuration is that, when you comfort at the switch when it arrives to the ' switch > ' command prompt is of type (- Enter - mean return carriage or all simply by pressing "Enter" on the keyboard):

enable - input -.

config t - enter-

Then copy the contents of the configuration and paste it directly to the session you have open. When the dough is finished, type:

end - enter-

WR - enter-

This will save the config for the switch. That's all.

Easy vpn server issues of Cisco 800 series.

Hello.

I want to deploy the easy vpn server on cisco 876 and 877 10 routers and access from a remote location (company headquarters). When I leave the firewall of the router off the vpn server works. When I turn it on it doesn't.

Although I allow all traffic to my ip for example 80.76.61.158 I can't access the vpn server.

I tried a place to let the firewall off and it worked fine.

I use SDM to configure the vpn server. Any ideas what I can do with the cause of firewall I really can't leave it "open."

Thanks in advance.

It would be a good idea to paste the configuration of the VPN server to the firewall.

Kind regards

Kamal

AnyConnect vpn client gives error of certificate on ios cisco 2800 series

Dear all,

I set up a vpn on cisco router ios simple anyconnect 2811

I also configured natting on the inorder of router to access the internet for local users

My problem

I can not connect same vpn if I use the method of the anyconnect vpn client

Also please tell me how to access internal resources by configuring split tunneling

the error I get is as below

* 08:16:35.947 Feb 8: 252:error:14094416:SSL routines: SSL3_READ_BYTES:sslv3 certificate alert unknown:../../../../cisco.comp/pki_ssl/src/openssl/dist/ssl/s3_pkt
.c:1062:SSL alert number 46

Here is my configuration

ABC host name
!

start the flash system: c2800nm-advsecurityk9 - mz.124 - 24.T1.bin

!
AAA new-model
!
!
AAA authentication login default local
local connection SSL-VPN-AUTH authentication AAA
!
!
AAA - the id of the joint session
!
dot11 syslog
IP source-route
!
!
IP cef
!
!
IP-server names 4.2.2.2
!
Authenticated MultiLink bundle-name Panel
!
!
!
Crypto pki trustpoint ABC
enrollment selfsigned
crl revocation checking
rsakeypair ABC 1024
!
!
ABC crypto pki certificate chain
self-signed certificate 04
3082023 HAS 308201 3 A0030201 02020104 300 D 0609 2A 864886 F70D0101 04050030
27312530 2306092A 864886F7 0D 010902 73 732 6569 6173742D 6B 686177 16166D
616E6565 6A2D7261 31313032 30383038 32333036 5A170D32 30303130 301E170D
3030305A 31303030 30273125 30230609 2 A 864886 F70D0109 0216166D 65 73732
2D6B6861 69617374 77616E65 656A2D72 6130819F 300 D 0609 2A 864886 F70D0101
01050003 818 0030 81890281 8100C16D 1007E434 AFAEE3C1 90141205 E7785754
FA3C4589 3D6B3D47 57BC54A5 7237E7FE 9B7CA69C 999B4DAF 835B98E9 972CFD03
5A43488C 05E82E10 9B540AB9 5A54AB0C 525FED0E 05B6F2FF 6703F0BD F28AE6F2
9E98298D E184CCDC 2D54741D 589 9731 C2BA5191 59DC7DC8 1F03C116 DDCF21EB D
0BB4E931 02F61F64 D64A6F36 92F70203 010001A 3 76307430 0F060355 1 130101
FF040530 030101FF 30210603 551D 1104 1A 301882 7373 656961 2 73742D6B 166D
68617761 2 726130 1 230418 30168014 2FA1E05E 1BD981A0 1F060355 6E65656A
A3485444 0B151D9E 44A3F6F6 301D 0603 551D0E04 1604142F A1E05E1B D981A0A3
4854440B 151D9E44 A3F6F630 0D06092A 864886F7 010104 05000381 810096EF 0D
39D4EEED E3CA162B E6BC1B61 0C3C66ED 02884209 0F4B54F1 BA7BEFF4 CAA206CE
44 C 99817 134363 2 F29A9E6A 945AA1B4 E4B85ED7 1800DAA1 30BE25C3 8340AE80
714F8FBD 9A433C4B 3EE2204D 88F7AB6D 929B5C88 5E7BC2B9 25754390 1622DB7B
EEB11694 F381E995 59C825BE 52EA5923 F87C43A3 98744BE8 BB27C381 BE14
quit smoking
!
!
privilege of username XXXX XXXX 15
username password ABC ABC
Archives
The config log
hidekeys
!
!
!
!
!
!
!
!
interface FastEthernet0/0
IP address | public IP address. 255.255.255.252
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
!
interface FastEthernet0/1
IP 192.168.0.7 255.255.255.0
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
!
interface FastEthernet0/2/0
no ip address
Shutdown
automatic duplex
automatic speed
!
local pool IP 10.10.10.1 intranet 10.10.10.254
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 GATEWAY
no ip address of the http server
IP http secure server
!
!
IP nat inside source map route sheep interface FastEthernet0/0 overload
!
extended IP access allow-traffic-to-lan list
deny ip 192.168.0.0 0.0.0.255 10.10.10.0 0.0.0.255
Licensing ip 192.168.0.0 0.0.0.255 any
!
access-list 101 permit ip 192.168.0.0 0.0.0.255 10.10.10.0 0.0.0.255
!
!
!
sheep allowed 10 route map
match ip address allow-traffic-to-lan
!
!
!
WebVPN EIAST gateway
IP address | public-ip | port 443
redirect http port 80
SSL trustpoint ABC
development
!
WebVPN install svc flash:/webvpn/anyconnect-win-2.5.2018-k9.pkg sequence 1
!
WebVPN context XYZ
SSL authentication check all
!
!
political group XYZ
functions compatible svc
SVC-pool of addresses "intranet".
SVC split include 10.10.10.0 255.255.255.0
SVC-Server primary dns 213.42.20.20
Group Policy - by default-XYZ
list of authentication SSL-VPN-AUTH of AAA.
area of bridge XYZ XYZ
10 Max-users
development
!
end

Thank you

Jvalin

You could hit the next bug

CSCtb73337 AnyConnect does not work with IOS if cert not trust/name of offset
which is set at 12.4 (24) T02.

Please update the code and give it a try.

Cisco 1220 series b AP

Similar Questions

Maybe you are looking for