Cisco 1200 Series AP - expand the network?

Similar Questions

• Aironet 1200 series - power of the weak signal near AP

  I recently bought an access point of the Aironet 1200 (AIR-AP1231G-A-K9) series and the initial setup - IP configuration on the AP, the installer does a SSID and turn on the radio.

  I used my laptop to connect to the SSID that I created, but to my surprise the signal strength of my SSID was only 2 bars and sometimes 1 bar and I'm within 2 feet of the access point. However, the speed of connection/signal quality was varying between 24 Mbps and 36 Mbps.

  Why is the signal strength so low?

  Is is because I did not buy them with external antennas?

  I missed something during the initial Setup?

  Y at - it an option that I have change/fine adjust in the GUI to get the best signal strength?

  Help, please.

  "Is is because I did not buy them with external antennas?

  Yes, that's correct. There is no internal antennas on this model of AP.

  You need at least one, preferably two antennas of the same type for each radio. If you have the old 'A' radio with the paddle antenna, then you only need one or two antennas of radio 2.4 G.

  Good luck

  Scott

• HP Photosmart 6510 series connects to the network and Internet, but not the computer.

  Hey all,.

  I have a desktop H8-1228 and 6510 e - printer.  I got both products at the same time.  I did the initial installation, and everything worked perfectly.  I was able to print of my HP Touchpad (the printer was on the floor and my Touchpad was down.).  Recently, I made a trip for two weeks.  I turned off the printer.  This seems to have been a mistake.  Now, he will only contact my network and Internet, but not the computer.  The Setup program keeps telling me that it is 'Impossible to find the printer' and that he wants me to check the IP address of the printer.  I did this many times by printing the HP's Configuration Page from the printer screen.  I also used Windows "Add a printer" without success.

  I have installed and uninstalled the software several times; every time that remove the icon of the printer and the Standard TCP/IP port in the "Devices and printers" section in Control Panel.  A few minutes earlier, I used Regedit to delete any reference to the series of HP Photosmart 6510 in the registry, believing that it could help my situation.  There can be no. :-(  I did the installation with the same problems that I had all the other times that I tried to install it.

  No help from you the printer experts will be greatly appreciated.  I'm not a novice as you can see.  This situation, however, launched my posterior. :-))

  Hi old_geekster,

  You may want to enable disable all startup programs in msconfig until you are able to access the Web integrated printer server. It seems that there is something in the communication with the printer's operating system blocking. It will most likely software firewall or security related.

  HP has designed a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity: The HP Print and Scan doctor. HP recommend you to download and install Print and scan doctor no matter what time you need to solve a problem with your HP printer from the link below.

  I would like to know what are the errors you receive?

  http://www.HP.com/go/tools

• console series via the network - supported?

  Hello

  I tried to configure the console series accessible over the network.

  But the error message:

  serial0 [msg.serial.pipe.posix.bind.bind]: unable to bind the socket to the server: no such file or directory

  My config:

  Serial0.present = 'TRUE '.

  Serial0.filetype = 'pipe '.

  Serial0.filename = "telnet://192.168.222.1:10000".

  Serial0.yieldOnMsrRead = 'TRUE '.

  Serial0.pipe.endpoint = 'server '.

  192.168.222.1 is the ip address of my PC and the port tcp/10000 is not used.

  Thank you

  It is not officially supported on the merger, but try this:

  Serial0.present = 'TRUE '.

  Serial0.filetype = 'network '.

  Serial0.filename = "0.0.0.0:10000".

  Serial0.network.endpoint = 'server '.

  Serial0.startConnected = 'TRUE '.

  (or you can replace to a host interface address 0.0.0.0, if you do not want to listen on all interfaces).

  See you soon,.

  --

  Darius

• My computer can not VAT registration and access the internet when connected to the network [secure] through wireless.

  Original title: fix problem 'local only' what is wireless.
   
  -My computer is a HP Pavilion dv5, running windows vista edition Home premium

  -My computer can identify and access the internet when connected to the network through a cable.

  -My computer can identify and access the internet when it is connected to the grace wireless network [without warranty].
  -My computer can't identify [unidentified network] and [room only] internet access when it is connected to the [secure] grace wireless network?
  -Other information systems, identify and access the internet when it is connected to the [secure] grace wireless network.
  -J' confirmed the network, try password works in "safe mode with network", manually configured (TCP/IPv4) using a connected computer.
  S ' Please, I'm desperate and in urgent need of help.

  Hello

  1. If it works well before?

  2 have you made any changes to the computer before the show?

  Method 1:

  You may experience connectivity problems or performance issues when you connect a portable computer that is running Windows Vista or Windows 7 to a wireless access point:
  http://support.Microsoft.com/kb/928152

  Method 2: Uninstall and reinstall the network adapter drivers.

  Follow the steps mentioned.

  (a) click Start, right click on computer.
  (b) click on properties, click on Device Manager
  (c) expand the network card, right-click the wireless adapter option
  (d) click on uninstall
  (e) now go to your computer/wireless device manufacturer's website, download the updated drivers and install them.

  Follow the below mentioned article:
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Intel wifi adapter xps m2010 disabled in Device Manager and in the network and sharing Center

  Original title: intel wifi adapter xps m2010

  for some reason any my intel pro wireless network adapter not turn on using the shortcut keys or by selecting with the mouse. Says its disabled in device in network and sharing Center Manager yet it does give me the option to activate it. Im confused

  Hi pillowgod,

  1. When did you start to question?

  2. you remember to make changes to the computer before this problem?

  You can check the following link and try to run the manual Intel WiFi diagnostic tool to check the functionality of your WiFi adapter.

  http://www.Intel.com/support/wireless/WLAN/sb/CS-025780.htm

  You can also try uninstalling and reinstalling the Intel wireless card and check.

  a. Click Start and type in Device Manager in the start search and press ENTER.

  b. expand the network adapters in the Device Manager

  c. right-click on the device, and then click Properties

  d. click on the driver tab and click on uninstall the drivers and click OK.

  e. restart the computer and check.

  You can also see the Intel Web site and try to download the latest version of the card wifi drivers.

  http://Downloadcenter.Intel.com/default.aspx

  You can also check out the link:

  http://www.Intel.com/support/wireless/WLAN/sb/CS-025807.htm

  Hope this information is helpful

• Some applications stopped the connection to the network, while the rest of them still not connect...

  A month ago, I realized that Hulu Desktop not working not. Gives me a generic error message. but nothing else. I thought that it was related with Hulu Desktop, then, naturally I looked for support on their site.

  During this time, I realized application Pandora AIR One did not work either. I thought that this might be related with Adobe Flash player or Adobe AIR. My first goal turned in this sense.

  Then I finally realized than iTunes, and also stopped the Cisco VPN client connection to the network.

  I use these applications on a daily basis, make none of the apps took about two weeks. Try to find a common solution in question, and possibly on another two weeks...

  Moreover, the rest of the applications work fine, no glicth: these are some of the applications, I use every day without any problem:

  • Internet Explorer
  • Chrome
  • Firefox
  • Opera
  • Safari
  • FileZilla FTP

  First of all the error messages I get:

  Windows Sidebar Gadgets (Weather, RSS Reader, etc.)
  Unable to connect to the service.

  Cisco AnyConnect VPN Client
  Connection failed: the host is unreachable.

  Hulu Desktop
  We're sorry, but Hulu Desktop is unable to connect to the server.
  Please check your internet connection settings and try again.

  Pandora
  Your computer has problems of connection to the network.
  Click 'connect' to try again.

  iTunes
  iTunes could not connect to the iTunes Store.
  Make sure your network connection is active and try again.

  This is the only application error messages. Windows is not trow an error.
  Here are a few things I tried, with the hope of resolving this problem of connection of mystery:
  (not in this specific Ref. necessarily)
  • Wireless connection with wired connection of switch to a router
  • Connect my laptop directly to the cable modem
  • Turning off Windows Firewall (firewall)
  • Reset the Windows Firewall to the default settings
  • Deactivation of Microsoft Security Essentials (anti-virus)
  • Open the computer in Mode safe mode with networking
  • Uninstall and reinstall these applications and the related necessary subsets such as Flash Player, AIR, etc.

  A friend suggested the creation of a local account on Windows. So I tried that too. I created two accounts; an admin and a guest. Not surprisingly (!) these requests, I'm having problems for almost a month or two, worked. No error message, just worked.
  Here's the thing: I still don't know what's causing this problem on my main account from the system.
  I can move all my settings and configurations of the new account system. But what happens if these problems occur again. It's already a big hassle, autour file transfer and the account settings.
  Has anyone out there have similar problems and/or has the answer, please help me. It's so frustrating. I appreciate any leads or you can provide solutions.
  Thank you
  Osman
  p.s. I do not think that everything is relevant but here's HW and SW Details:
  Windows 7 Professional 64 bit
  Dell Precision M4300 laptop
  All the toutes les mises updates update Windows Update, all mentioned applications, drive, Flash, AIR, etc are up to date.

  I found the solution. :-)

  Open Internet Options, Advanced tab. Click the reset button in the box 'Settings reset Internet Explorer'.

  My applications are now online.

  Read this article if you need help to reset IE:

  http://Windows.Microsoft.com/en-us/Windows7/reset-Internet-Explorer-settings

• Reinstall the network card, but there is an error code (31)?

  Hi all! This is my first time asking in this forum so please guide me if I make mistakes.

  I use a Dell Inspiron laptop n5110, and recently I had problems with my wireless internet connection. Most of the time at halfway then I am browsing or buffering videos, my internet would simply cut all of a sudden and it goes to show that its connected, but there is not internet access/no access to the network. Sometimes, it just goes to a network not identified without internet access.

  To resolve this problem, I accessed my disabled device manager then activated my network card and the internet reconnected instantly. However, it was not a permanent solution and the same problem has occurred over and over again, sometimes in succession. I called the guy in charge of my internet and I doubt it's a problem on their side, so I thought it would probably be a problem with my network card.

  I uninstalled my network card and reinstalled, but now I can not connect to internet at all. Nothing shows up on my list of connections available now. The only reason why I am able to ask this question is because I'm using my iphone usb hotspot.

  I checked my network card and it shows "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) ». I hope someone can help me with this. Sorry for the long post as well, I just thought that some of you will want to know what happened before.

  Hello

  Welcome to the Microsoft community!

  I really appreciate your efforts to solve the problem and provide us with the required information that will help us troubleshoot and fix your problem.

  As the error code says, the question arises if the device driver is corrupted and Windows cannot update the drivers for the network card. I suggest you refer to the solution recommended for Code 31 has been provided in the following Knowledge Base article:

  Error codes in the Device Manager in Windows

  In addition, I would suggest trying the following methods and check if the problem persists.

  Method 1:

  According to the error code, I suggest you run the troubleshooter devices & hardware and check if it helps.

  Open the hardware and devices Troubleshooter

  If the problem persists, try the following method.

  Method 2:

  Uninstall and reinstall the network driver from the Dell support site.

  Step 1:

  (a) press the Windows key + R.

  (b) type devmgmt.msc in the run window.

  (c) expand the network adapters in the Device Manager list.

  (d) right click on the concerned device driver and click Uninstall.

  After you have uninstalled the driver, proceed to the next step.

  Step 2:

  Download and install the latest driver from the following link network.

  Drivers Dell Inspiron 15R (N5110, Early 2011)

  Note: Select the Windows 7 as the network and operating system under article of the category.

  Check whether the problem is resolved.

  Additional information:

  Wireless and wired network problems

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• Connected to the network but no internet access?

  I had problem connecting to internet. What is happening is that my computer connects to my wifi network, but then a yellow sign with exclamation sign will appear and it says "no Internet access. I'm tired of checking my browsers and they do not connect. I tried ping and he said something in the sense of "cannot find server". Tried to update the drivers, but either they are up to date, or even can not be updated because it is not connected to the internet. Finally, I tried the system restore, and it worked miraculously! But now, about a few days later, the problem came again and I restored the system again. But I thought I can't do this forever. Is there a way to fix it or at least to know what is the problem?

  Before I restored it, I wrote the changes that making it in my programs and updates that will be removed or modified. They are here:

  Adobe Reader X (10.1.4) MUI 10.1.4
  Microsoft (Bluetooth) 06/21/2006 6.1.7601.17889
  Fix for Package_for_KB2732487 (KB2732487)
  Update of security for Package_for_KB2705219 (KB2705219)
  Update of security for Package_for_KB2712808 (KB2712808)
  Update of security for Package_for_KB2722913 (KB2722913)
  Update of security for Package_for_KB2731847 (KB2731847)
  Update for Package_for_KB2647753 (KB2647753)
  Update for Package_for_KB2729094 (KB2729094)
  Update for Package_for_KB2732500 (KB2732500)

  Adobe Reader X (10.1.3) MUI 10.1.3
  Microsoft (Bluetooth) 06/21/2006 6.1.7601.17607

  Also, I know that this is not a problem with my router or modem because all other devices in my house can access the internet except for mine. I tried to connect my laptop through an ethernet cable, and it still does not work.

  My computer is an Acer Aspire Timeline X 5830TG-6614

  Thanks for the help!

  Hi FinalEclipse,

  Follow the steps below to update your network adapter driver:

  1. If your computer is a Dell, HP, Sony, etc., go to the manufacturer Web site and download the driver for your network card, specific to your computer model and save the file to your desktop so that it is easy to locate.
  2. On your computer, click Start
  3. Right click on computer then Properties
  4. Select Device Manager
  5. Expand the network adapters
  6. Right-click on your network map, and then select Update driver software
  7. Select Browse my computer for driver software
  8. Click Browse
  9. Select desktop
  10. Select the driver that you saved in step 1.
  11. Click Next and follow the remaining instructions.

  Let us know if that helps.

• Installation Failed for HP Laserjet 1200 Series in the new computer laptop with Windows 8, 64-bit

  Name of the product - HP Laserjet 1200 Series PCL 6 Driver

  Operating system: Windows 8 Home Edition, 64-bit

  Error message: cannot find the series 1200 on the network. To locate manually click ok...

  Changes Made - this is an installation on the new laptop, in Windows 8, 64-bit

  Description:

  1 installation of an existing network, consistedof a desk and two wireless laptops.

  2. the two portable computers have Windows 7, 64 bit. Above the named printer is accessed successfully for laptops.

  3 replaces one of cell phones with 8 64-bit Windows.

  4. the path of the 1200 series is: wireless printer to the router, router to the desktop via ethernet, from desktop to a printer via a cable.

  5. the configuration of the wireless printer is

  Name: HP Laserjet 1200 Series PCL 5

  Port: \\Central\HPLaserj

  Printer: HP Laserjet 1200 Series PCL 5

  Driver: HPMCPM25. GPD 5.8.2008

  Problem

  Impossible to re-create this path with Windows 8, 64-bit configuration.

  a. when I try to download a driver always end up with a file called UPD-pcl6 - x 64 - 5.6.0.14430

  This seems to be a universal PCL 6 printer driver, can successfully decompress the file and create a folder

  b. during installation, I can see the desktop ICON printer (name: \\central\HPLaserj); So far so good

  c. process is unable to locate a driver and ordered to locate manually.

  d. accessing the HP Universal Driver files fails because a driver is not found.

  e. caraa attempt enter fails because you can't enter address above (\\central\HPlaserj). Cannot enter HPLaserj for the address, which obviously does not work.

  f. when the installation showed a list of drivers, the only one that I found was a universal PCL 6, which is what I thought, I tried to download the original.

  This set up has worked successfully to Windows 7 64 bit. It seems that I need help much more expertise to guide me through this whole upward.

  Problem solved.

  This link gives a good overview of the solution

  http://www.sadjad.net/blog/2012/11/28/Windows-8-shared-printer-driver/

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?

• OfficeJet 6500 E709n series cannot be contacted over the network. Reinstalled, rebooted several times.

  Running Win 7/32 on two different computers HP laptop and updates on 2 iPhones and 2 iPad2s. I also have DirecTV whole House wireless set up through this network. The router is an E4200 of Cisco (Linksys), with the latest firmware and software updates, running Mixed Mode WPA2/WPA encryption.

  I installed, removed, rebooted and reinstalled the printer several times and do not see it, other than on the router's routing tables. I am unable to ping and can't see any (other than Cisco) software.

  I have tried to use the installation wizard 'automatic' in the menu of the printer #8, has made 'restore defaults', is 'advanced configuration', IP address and used auto and even with the SSID and key, I'm headed to an IP address that is not even close to be part of my network. I tried manual IP and combination of wireless configuration and put the IP address that shows on the Cisco Routing table. I tried "restore default settings", and then reinstalled the software after you have uninstalled and restarted everything. I tried HP Network Diagnostic Utility, and it can't find any problems on my network, another it does not find the printer.

  Nothing is allowing me to see the printer, except when I connect it via USB.

  Does anyone have any ideas where I can go for an answer?

  I found a solution validated by PrintDoc that worked:

  A static IP address is always a good idea for a printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address). If you don't know it, enter the current IP address.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the gateway and DNS white. Click on ' apply

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

  -instead of remake "Add a printer", I was able to change the properties of my current setup and add a new TCP/IP port, using the name of the computer, I had specified in the static DHCP entry in my router. Finally, it worked and I'm now able to print again from my laptop and the application of 'Print-N-Share' on my iPad and iPhone.

  Thanks PrintDoc! You got me most of the way and I managed to finish it.

• the need to increase the speed of the network on my vpshere 4.1 with cisco 3750

  Hello

  Must I increase now my network speed on my esxi vpshere 4.1 my switch cisco 3750.  the rdp on the erp application is now affected with speed.  What would be the best solution on this?  each host on my vpshere have two NICs for the network of the vm and vmotion.  each network adapter is 1 G and cisco 3750 is the bandwidth of 1 G.

  Add multiple NICs for vmotion separated and the vm network?  do all the network adapters in vm network stuck for a bandwidth of submission?  or do I just have to prioritize the rdp session in my cisco switch?  or all will help?

  help please, thank you.

  It is recommended to separate management, vmotion, storage and LAN VM traffic from each other (or in the case of 10 G, use QOS at the rate limit and separate each type of traffic...

  On a standard server with 50 or so VM on it, double 1Gbit nic is much band bandwidth for traffic of vm... and actually on the blades, I saw 2x1GB nic handle all traffic very well...

  RDP uses about 121kbits/s of traffic per session rdp (on average)... I highly doubt that the speed of ar causing you performance issues your card network interface, but you should easily be able to tell if you are having problems of saturation of the network with a simple PRTG, MRTG or solarwinds type of surveillance.